Integer division may truncate the result.
Use DIV_ROUND_UP to ensure new voltage setting falls within specified range.
Also properly handle the case min_vol < desc->min to ensure we don't return
negative value for selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regulator is always on for any reason then cache that when the
consumer is created and use it to optimise away the need to take locks
or recurse up the supply tree when consumers do enable or disable calls.
The scheduling of asynchronous work for bulk enables is also skipped.
We don't actually check if the device physically supports control on the
basis that constraints allowing status changes on physically always on
regulators are nonsensical anyway.
This is a very common pattern in hardware - it's normal to have some
power supplies that have either no software control or are critical to
system function - so many systems should be able to benefit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
commit 4ca1e1d "regulator: Convert 88pm8607 to set_voltage_sel" accidentally
changed the value writing to vol_reg.
What we want is to write val instead of selector to vol_reg.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts tps65090 regulator driver to use generic regmap
enable/disable operations.
Also move struct tps65090 to include/linux/mfd/tps65090.h because
the regulator driver needs to access the rmap field of struct tps65090.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename get_current_limit and set_current_limit callbacks
to max8997_get_current_limit and max8997_set_current_limit for
better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 4d26f7 "regulator: max8660: Use devm_kzalloc()" missed to
replace kzalloc by devm_kzalloc. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_set_optimum_mode needs set_mode to properly work.
Add checking for set_mode callback in case it may be not implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the enable(), disable() and is_enabled() operations for most regmap
based regulators come down to reading and updating a single register bit
we can factor out the code and allow these drivers to just define which
bit to update using the enable_reg and enable_mask fields in their desc
and then use operations provided by the core.
As well as the code saving this opens the door to future optimisation of
the bulk operations - if the core can realise that we are updating a
single register for multiple regulators then it should be able to combine
these updates into a single physical operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since the voltage selector operations are intended to directly map a
bitfield in the device register map into regulator API operations the
code for implementing them is usually very standard we can save some
code by providing standard implementations for devices using the regmap
API.
Drivers using regmap can pass their regmap in in the regmap_config
struct, set vsel_reg and vsel_mask in their regulator_desc and then
use regulator_{get,set}_voltage_sel_regmap in their ops. This saves
a small amount of code from each driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since many regulators use regmap for register I/O and since there's quite
a few very common patterns in the code allow drivers to pass in a regmap
to the core for use in generic code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In current implementation, to support set_suspend_voltage and set_suspend_mode
the regulator code needs the regulator driver to implement both
set_suspend_enable and set_suspend_disable callbacks.
This patch removes this limitation. In the case set_suspend_enable and/or
set_suspend_disable are NULL, the regulator code assumes we don't need to
do any thing to enable/disable regulator when system is suspended and
then will continue to handle set_suspend_mode and set_suspend_voltage.
Currently the regulator core creates suspend state related sysfs entries only
if both set_suspend_enable and set_suspend_disable callbacks are not NULL.
A side-effect of this change is that the regulator core will create suspend
state related sysfs entries unconditionally now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to implement set_voltage() as there is only a very small
range of selectors for the regulators in the WM8994 and the voltages are
not expected to vary frequently at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't support missing configs at all so segfaulting isn't that bad
but since we've got checks in the code move the dereference after them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
commit 268a1 "regulator: twl-regulator: Use DIV_ROUND_UP at appropriate places"
introduced an off-by-one bug for setting vsel.
The linear calculation code in twl6030smps_list_voltage() does subtract index
by 1 so we need the vsel++ after DIV_ROUND_UP.
The original code use this trick to differentiate if we are going to set the
voltage to 0 or the voltage falls within the linear calculation range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes the code easier to read.
Also add checking the case when no desc id is matched. This is required because
if no desc id is matched, the poiner info is pointed to twl_of_match[i].data
which may be not NULL. Checking info is NULL or not latter does not catch the
error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The n_bits is only used in max8997_get_voltage_proper_val to check the valid
range for variable i.
Current code already ensures min_vol never greater than desc->max,
which means the variable i always in the valid range:
0 .. (desc->max - desc->min)/desc->step.
Thus we can remove the checking (i >= (1 << desc->n_bits) and then remove
n_bits from struct voltage_map_desc.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
