If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This MIPS driver does not support COMPILE_TEST yet and failed to build
under my radar.
Replace 'mtd' chich is not defined in the scope of xway_nand_remove()
by nand_to_mtd(chip). The mistake has been added in the long series
dropping nand_release().
Tested with a 7.3.0 MIPS GCC toolchain built with Buildroot.
Fixes: 9fdd78f7bc ("mtd: rawnand: xway: Stop using nand_release()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200626065511.16424-1-miquel.raynal@bootlin.com
A MDMA issue has been solved on Kernel 5.7. The effect of this fix is
that the MDMA driver is now deferred and the FMC2 NFC driver is also
deferred. All is working fine but there is a FMC2 log in the console:
stm32_fmc2_nfc 58002000.nand-controller: failed to request tx DMA
channel: -517
This patch removes the display of this log in the console in case of
this error is -EPROBE_DEFER.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-2-git-send-email-christophe.kerello@st.com
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Implement ECC correctable and uncorrectable error handling for EDU
reads. If ECC correctable bitflips are encountered on EDU transfer,
read page again using PIO. This is needed due to a NAND controller
limitation where corrected data is not transferred to the DMA buffer
on ECC error. This applies to ECC correctable errors that are reported
by the controller hardware based on set number of bitflips threshold in
the controller threshold register, bitflips below the threshold are
corrected silently and are not reported by the controller hardware.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-3-kdasu.kdev@gmail.com
BAM is DMA controller on QCOM ipq platforms, BAM mode on NAND driver
is set by writing BAM_MODE_EN bit on NAND_CTRL register.
NAND_CTRL is an operational register and in BAM mode operational
registers are read only.
So, before enabling BAM mode by writing the NAND_CTRL register, check
if BAM mode was already enabled by the bootloader, and enable BAM mode
only if it is not enabled already.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591948696-16015-3-git-send-email-sivaprak@codeaurora.org
Instead of manipulating the statically allocated structure and copy
timings around, allocate one at identification time and save it in the
nand_chip structure once it has been initialized.
All NAND chips using the same interface configuration during reset and
startup, we define a helper to retrieve a single reset interface
configuration object, shared across all NAND chips.
We use a second pointer to always have a reference on the currently
applied interface configuration, which may either point to the "best
interface configuration" or to the "default reset interface
configuration".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-29-miquel.raynal@bootlin.com
The Kioxia/Toshiba TH58NVG2S3HBAI4 NAND memory is not ONFI compliant.
The timings of the NAND chip memory are quite close to ONFI mode 4 but
is breaking that spec.
By providing our own set of timings, erase block read speed is increased
from 6910 kiB/s to 13490 kiB/s and erase block write speed is increased
from 3350 kiB/s to 4410 kiB/s.
Tested on IMX6SX which has a NAND controller supporting EDO mode.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-27-miquel.raynal@bootlin.com
The name/suffix data_interface is a bit misleading in that the field
or functions actually represent a configuration that can be applied by
the controller/chip. Let's rename all fields/functions/hooks that are
worth renaming.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ONFI parameter page of a chip might define more fine grained
tPROG_max and tBERS_max. When we do not have this information, we
default to the highest possible values (they are maxima anyway).
There is no point setting these fields at runtime, so explicitly move
these defaults to the main ONFI SDR timings structure. This way, we
will also be able to return a pointer to mode 0 directly when we will
create a default reset configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-18-miquel.raynal@bootlin.com
Right now the core uses onfi_fill_data_interface() to initialize the
nand_data_interface object embedded in nand_chip, but we are about to
allocate this object dynamically and let manufacturer drivers provide
their own interface config. Let's patch the onfi_fill_data_interface()
so it can initialize an interface config that's not the one
currently attached to the nand_chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-14-miquel.raynal@bootlin.com
