Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
Pull ARM SoC updates from Arnd Bergmann:
"These are updates for SoC specific code, mostly in the 32-bit
architecture:
- A rework for handling MMIO accesses in Renesas SoCs in a more
portable way
- Updates to SoC version detection in NXP i.MX SoCs.
- Smaller bug fixes for OMAP, Samsung, Marvell, Amlogic"
* tag 'arm-soc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: Kconfig: meson: drop pinctrl
ARM: mxs: Add serial number support for i.MX23, i.MX28 SoCs
MAINTAINERS: switch mvebu tree to kernel.org
MAINTAINERS: Add an entry for MikroTik CRS3xx 98DX3236 boards
ARM: shmobile: Stop using __raw_*() I/O accessors
ARM: shmobile: sh73a0: Remove obsolete static mapping
ARM: shmobile: sh73a0: Use ioremap() to map SMP registers
ARM: shmobile: sh73a0: Use ioremap() to map L2C registers
ARM: shmobile: r8a7779: Remove obsolete static mappings
ARM: shmobile: r8a7779: Use ioremap() to map SMP registers
ARM: shmobile: r8a7779: Use ioremap() to map INTC2 registers
ARM: shmobile: r8a7778: Introduce HPBREG_BASE
ARM: OMAP1: clock: Use IS_ERR_OR_NULL() to clean code
ARM: OMAP2+: Remove redundant null check before clk_prepare_enable/clk_disable_unprepare
ARM: OMAP2+: Remove redundant assignment to variable ret
ARM: OMAP2+: Fix kfree NULL pointer in omap2xxx_clkt_vps_init
ARM: OMAP2+: Fix memleak in omap2xxx_clkt_vps_init
ARM: exynos: extend cpuidle support to P4 Note boards
ARM: imx: mach-imx6q: correctly identify i.MX6QP SoCs
ARM: imx: imx7ulp: Add a comment explaining the B2 silicon version
...
Pull asm-generic cross-architecture timer cleanup from Arnd Bergmann:
"This cleans up two ancient timer features that were never completed in
the past, CONFIG_GENERIC_CLOCKEVENTS and CONFIG_ARCH_USES_GETTIMEOFFSET.
There was only one user left for the ARCH_USES_GETTIMEOFFSET variant
of clocksource implementations, the ARM EBSA110 platform. Rather than
changing to use modern timekeeping, we remove the platform entirely as
Russell no longer uses his machine and nobody else seems to have one
any more.
The conditional code for using arch_gettimeoffset() is removed as a
result.
For CONFIG_GENERIC_CLOCKEVENTS, there are still a couple of platforms
not using clockevent drivers: parisc, ia64, most of m68k, and one Arm
platform. These all do timer ticks slighly differently, and this gets
cleaned up to the point they at least all call the same helper
function.
Instead of most platforms using 'select GENERIC_CLOCKEVENTS' in
Kconfig, the polarity is now reversed, with the few remaining ones
selecting LEGACY_TIMER_TICK instead"
* tag 'asm-generic-timers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
timekeeping: default GENERIC_CLOCKEVENTS to enabled
timekeeping: remove xtime_update
m68k: remove timer_interrupt() function
m68k: change remaining timers to legacy_timer_tick
m68k: m68328: use legacy_timer_tick()
m68k: sun3/sun3c: use legacy_timer_tick
m68k: split heartbeat out of timer function
m68k: coldfire: use legacy_timer_tick()
parisc: use legacy_timer_tick
ARM: rpc: use legacy_timer_tick
ia64: convert to legacy_timer_tick
timekeeping: add CONFIG_LEGACY_TIMER_TICK
timekeeping: remove arch_gettimeoffset
net: remove am79c961a driver
ARM: remove ebsa110 platform
arm64: Kconfig.platform: amlogic updates for v5.11
- ship only the necessary clock controllers
* tag 'amlogic-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: meson: ship only the necessary clock controllers
Link: https://lore.kernel.org/r/7hlfehjgv8.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.11, please pull the following:
- Rafal adds initial support for the Broadcom 4908 which are SoCs used
in home routers and are based on the DSL architecture and using
Broadcom Brahma-B53 CPUs.
* tag 'arm-soc/for-5.11/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: add config for Broadcom BCM4908 SoCs
arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files
dt-bindings: arm: bcm: document BCM4908 bindings
Link: https://lore.kernel.org/r/20201128163410.1691529-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add ARCH_BCM4908 config that can be used for compiling DTS files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Almost all machines use GENERIC_CLOCKEVENTS, so it feels wrong to
require each one to select that symbol manually.
Instead, enable it whenever CONFIG_LEGACY_TIMER_TICK is disabled as
a simplification. It should be possible to select both
GENERIC_CLOCKEVENTS and LEGACY_TIMER_TICK from an architecture now
and decide at runtime between the two.
For the clockevents arch-support.txt file, this means that additional
architectures are marked as TODO when they have at least one machine
that still uses LEGACY_TIMER_TICK, rather than being marked 'ok' when
at least one machine has been converted. This means that both m68k and
arm (for riscpc) revert to TODO.
At this point, we could just always enable CONFIG_GENERIC_CLOCKEVENTS
rather than leaving it off when not needed. I built an m68k
defconfig kernel (using gcc-10.1.0) and found that this would add
around 5.5KB in kernel image size:
text data bss dec hex filename
3861936 1092236 196656 5150828 4e986c obj-m68k/vmlinux-no-clockevent
3866201 1093832 196184 5156217 4ead79 obj-m68k/vmlinux-clockevent
On Arm (MACH_RPC), that difference appears to be twice as large,
around 11KB on top of an 6MB vmlinux.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A separate Kconfig option HAVE_S3C2410_WATCHDOG for Samsung SoCs is not
really needed and the s3c24xx watchdog driver can depend on Samsung ARM
architectures instead.
The "HAVE_xxx_WATCHDOG" pattern of dependency is not popular and Samsung
platforms are here exceptions. All others just depend on
CONFIG_ARCH_xxx.
This makes the code slightly smaller without any change in
functionality.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
Select TI chip id driver for TI's SoCs based on K3 architecture to provide
this information to user space and Kernel as it is required by other
drivers to determine SoC revision to function properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
I got a build failure with CONFIG_ARCH_SPRD=m when the
main portion of the clock driver failed to get linked into
the kernel:
ERROR: modpost: "sprd_pll_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_comp_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_probe" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_regmap_init" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
This is a combination of two trivial bugs:
- A platform should not be 'tristate', it should be a 'bool' symbol
like the other platforms, if only for consistency, and to avoid
surprises like this one.
- The clk Makefile does not traverse into the sprd subdirectory
if the platform is disabled but the drivers are enabled for
compile-testing.
Fixing either of the two would be sufficient to address the link failure,
but for correctness, both need to be changed.
Fixes: 2b1b799d76 ("arm64: change ARCH_SPRD Kconfig to tristate")
Fixes: d41f59fd92 ("clk: sprd: Add common infrastructure")
Acked-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_COMMON_CLK_VERSATILE doesn't really do anything other than hiding
Arm Ltd reference platform clock drivers. It is both selected by the
platforms that need it and has a 'depends on' for those platforms. Let's
drop the selects and convert CONFIG_COMMON_CLK_VERSATILE into a
menuconfig entry. With this make CONFIG_ICST visible.
Move the 'select REGMAP_MMIO' to the drivers that require it (SP810 did
not).
This also has the side effect of enabling CONFIG_ICST for COMPILE_TEST
as it was not visible before.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The VExpress power-off/reset driver is not needed on 64-bit platforms as
PSCI power-off and reset can be used instead. Stop selecting it so it
can be disabled and not always built-in.
CONFIG_VEXPRESS_CONFIG can also be dropped as it was a dependency for
CONFIG_POWER_RESET_VEXPRESS.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
Unlike on arm32, the HAVE_ARM_ARCH_TIMER config symbol does not exist on
arm64.
Note that the toplevel ARM64 symbol always selects ARM_ARCH_TIMER, so
support for it is always included.
Fixes: 628d30d1cc ("arm64: Add platform selection for BCM2835.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make zynqmp_firmware driver as optional to disable it, if user don't
want to use default zynqmp firmware interface.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
i.MX SoC update for 5.5:
- Add arm64 Kconfig option for the NXP S32 platform.
- Drop imx_anatop_usb_chrg_detect_disable() function which becomes
unneeded, since all the necessary charger setup is done by the USB
PHY driver now.
- Add serial number support for i.MX6/7 SoCs by reading 64-bit SoC
unique ID from OCOTP block.
- Replace i.MX machine specific coherency exit implementation using
the generic v7_exit_coherency_flush() function.
* tag 'imx-soc-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: use generic function to exit coherency
ARM: imx: Add serial number support for i.MX6/7 SoCs
ARM: imx: Drop imx_anatop_usb_chrg_detect_disable()
arm64: Introduce config for S32
Link: https://lore.kernel.org/r/20191105150315.15477-2-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Realtek ARM64 based SoC for v5.5
Enable reset controllers and add a mailing list to MAINTAINERS.
* tag 'realtek-arm64-soc-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek:
arm64: realtek: Select reset controller
MAINTAINERS: Add mailing list for Realtek SoCs
Link: https://lore.kernel.org/r/20191030041000.31848-1-afaerber@suse.de
Signed-off-by: Olof Johansson <olof@lixom.net>
Add configuration option for the NXP S32 platform family in
Kconfig.platforms. For starters, the only SoC supported will be Treerunner
(S32V234), with a single execution target: the S32V234-EVB (rev 29288)
board.
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the BCM2711 to ARCH_BCM2835, but use new machine board code
because of the differences.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Florian Fanelli <f.fainelli@gmail.com>
ARCH_MXC platforms needs system counter as broadcast timer
to support cpuidle, enable it by default.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
This pull request contains Broadcom ARM64-based SoCs Kconfig.platform
changes for 5.3, please pull the following:
- Jim adds the ability for ARCH_BRCMSTB to use reset controllers
- Doug adds the ability for ARCH_BRCMSTB to use the PINCTRL framework
- Florian enables the use of the BCM7038 Level 1 interrupt controller
for ARCH_BRCMSTB
* tag 'arm-soc/for-5.3/soc-arm64' of https://github.com/Broadcom/stblinux:
arm64: Enable PINCTRL for ARCH_BRCMSTB
arm64: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
arm64: Enable BCM7038_L1_IRQ for ARCH_BRCMSTB
Signed-off-by: Olof Johansson <olof@lixom.net>
Texas Instruments AM65x fixes for v5.2
- Fix up a Kbuild warning when SOC_TI is not set
* tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: arch_k3: Fix kconfig dependency warning
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips like
BCM7211 which adopted that pin controller for GPIO.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Allow the use of reset controllers on ARCH_BRCMSTB such as the recently
introduced RESET_BRCMSTB driver.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During randconfig builds, I occasionally run into an invalid configuration
drivers/soc/imx/soc-imx8.o: In function `imx8_soc_init':
soc-imx8.c:(.init.text+0x144): undefined reference to `soc_device_register'
while CONFIG_SOC_BUS is not set, the building failed like this. This patch
selects SOC_BUS to fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a7e26f356c ("soc: imx: Add generic i.MX8 SoC driver")
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
arm64: tegra: Core fixes for v5.2-rc1
This enables the ARM_GIC_PM driver by default for Tegra in order to
increase build coverage.
* tag 'tegra-for-5.2-arm64-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Select ARM_GIC_PM
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable ARM_GIC_PM for 64-bit Tegra devices. This is required to ensure
that the driver gets built into kernel and helps to register the AGIC
device when enabled in DT.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Select the TISCI Interrupt Router, Aggregator drivers and all its
dependencies for TI's SoCs based on K3 architecture.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
SoCFPGA DTS updates for v5.2
- Add base support for Agilex platform
- Add 'cap-mmc-highspeed' Stratix10 and 32-bit SoCFPGA platform
- Increase Stratix10 QSPI support to 100 MHz
* tag 'socfpga_dts_updates_for_v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA
arm64: dts: stratix10: increase QSPI max frequency to 100MHz
arm64: dts: stratix10: enable MMC highspeed support
ARM: dts: socfpga: enable MMC highspeed support
Signed-off-by: Olof Johansson <olof@lixom.net>
