Convert to YAML and add generic IP core compatibles "cnm,codadx6",
"cnm,codahx4", "cnm,coda7541", and "cnm,coda960" in addition to the SoC
specific compatibles. The new generic compatibles are already used in
the SoC device trees and replace the free form comments. For example:
- compatible : should be "fsl,<chip>-src" for i.MX SoCs:
(a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27
turns into:
properties:
compatible:
oneOf:
- items:
- const: fsl,imx27-vpu
- const: cnm,codadx6
This allows to properly specify the secondary JPEG unit interrupt that
is only present on cnm,coda960.
Also add the missing "fsl,imx6dl-vpu", "cnm,coda960" compatible.
The AXI bus connection to the internal SRAM is different between i.MX6Q
and i.MX6DL, which requires the driver to load a different firmware
depending on the SoC.
Further, specify the power-domain property for i.MX6 and change the
clock order from "ahb", "per" to "per", "ahb". This order is currently
used in all SoC device trees.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to establish required properties based on the selected
bus type, make the 'bus-type' property mandatory. As this change
documents an endpoint property, also document the 'remote-endpoint'
one now that the 'endpoint' schema has been expanded.
Binary compatibility with existing DTB is kept as the driver does not
enforce the property to be present, and shall fall-back to default
parallel bus configuration, which was the only supported bus type, if
the property is not specified.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document and adjust the compatibles for i.MX7S based boards.
The Toradex boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit:
0e030a373d ("can: flexcan: fix endianess detection")
the fsl,imx53-flexcan isn't compatible with the fsl,p1010-flexcan any more. As
the former accesses the IP core in Little Endian mode and the latter uses Big
Endian mode.
With the conversion of the flexcan DT bindings to yaml, the dt_binding_check
this throws the following error:
Documentation/devicetree/bindings/clock/imx5-clock.example.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx53-flexcan', 'fsl,p1010-flexcan'] is too long
Additional items are not allowed ('fsl,p1010-flexcan' was unexpected)
'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
'fsl,imx6q-flexcan' was expected
'fsl,lx2160ar1-flexcan' was expected
From schema: /builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
The error is fixed by replacing the "fsl,p1010-flexcan" compatible
(which turned out the be incompatible) with "fsl,imx25-flexcan" in the
binding example.
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111213548.1621094-1-mkl@pengutronix.de
[robh: Add "fsl,imx25-flexcan" as fallback]
Signed-off-by: Rob Herring <robh@kernel.org>
As both the i.MX35 and i.MX53 flexcan IP cores are compatible to the i.MX25,
they are listed as:
compatible = "fsl,imx35-flexcan", "fsl,imx25-flexcan";
and:
compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
in the SoC device trees.
This patch fixes the following errors, which shows up during a dtbs_check:
arch/arm/boot/dts/imx53-ard.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx53-flexcan', 'fsl,imx25-flexcan'] is too long
Additional items are not allowed ('fsl,imx25-flexcan' was unexpected)
'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
'fsl,imx6q-flexcan' was expected
'fsl,lx2160ar1-flexcan' was expected
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Fixes: e5ab9aa7e4 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-4-mkl@pengutronix.de
[robh: drop singular fsl,imx53-flexcan and fsl,imx35-flexcan]
Signed-off-by: Rob Herring <robh@kernel.org>
Add documentation for new optional properties in the exynos bus nodes:
interconnects, #interconnect-cells, samsung,data-clock-ratio.
These properties allow to specify the SoC interconnect structure which
then allows the interconnect consumer devices to request specific
bandwidth requirements.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The fsl,stop-mode property is a phandle-array and should consist of one phandle
and two 32 bit integers, e.g.:
fsl,stop-mode = <&gpr 0x34 28>;
This patch fixes the following errors, which shows up during a dtbs_check:
arch/arm/boot/dts/imx6dl-apf6dev.dt.yaml: can@2090000: fsl,stop-mode: [[1, 52, 28]] is too short
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Fixes: e5ab9aa7e4 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-5-mkl@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
RFC for adding a support for typical voltage scaling connection
In few occasions there has been a need to scale the voltage output
from bucks on BD71837. Usually this is done when buck8 is used to
power specific GPU which can utilize voltages down to 0.7V. As lowest
the buck8 on BD71837 can go is 0.8V, and external connection is used to
scale the voltages.
The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the
feedback pin using suitable voltage/resistors.
|---------------|
| buck 8 |-------+----->Vout
| | |
|---------------| |
| |
| |
+-------+--R2----+
|
R1
|
V FB-pull-up
This will scale the voltage as follows:
- Vout_o = Vo - (Vpu - Vo)*R2/R1
- Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
>From HW point of view this does not need to be limited to buck 8. This
connection can be used to adjust output from any of the bucks on
BD71837/47/50.
As this seems to be a 'de-facto' way to scale the voltages on BD71837 it
might be a good idea to support computing the new voltage ranges for
bucks based on the V-pull-up and resistor R1/R2 values given from
device-tree. This allows describing the external HW connection using DT
to correctly scale the voltages.
This RFC uses "rohm,feedback-pull-up-r1-ohms" and
"rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but
these names (without the picture) might not be too descriptive. I am
grateful for all suggestions as better and more descriptive names.
This patch series is an RFC because this connection feels somewhat
"hacky". OTOH - when hack becomes widely used, it is less of an hack and
more of a standard - and occasionally supporting HW hacks using SW may
benefit us all, right? :)
The other thing some projects do is allowing the change of BD71837 buck8
voltages when buck8 is enabled. This however will introduce voltage
spikes as buck8 was not originally designed for this. The specific HW
platform must be evaluated to be able to tolerate these spikes. Thus
this patch series does not support buck8 voltage changes when buck8 is
enabled. I wonder if this should be allowed per some config option(?) I
don't want to help people frying their boards... Opinions? Is there
suggested way of allowing this type of features at own risk? Config or
even Some #ifdef which is not listed in Kconfig? Device-tree property?
If you have (good) suggestions I could add the optional (non default)
DVS support for non DVS bucks on BD71837.
Matti Vaittinen (3):
dt-bindings: regulator: BD71837 support commonly used feedback
connection
dt-bindings: regulator: BD71847 support commonly used feedback
connection
regulator: bd718x7: Support external connection to scale voltages
.../regulator/rohm,bd71837-regulator.yaml | 48 +++++
.../regulator/rohm,bd71847-regulator.yaml | 49 ++++++
drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++-
3 files changed, 254 insertions(+), 7 deletions(-)
base-commit: 3cea11cd5e
--
2.21.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Note:
- The patch is made by the collaboration of
Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Cheng-Yi Chiang <cychiang@chromium.org>
v6:
- Documentation: Addressed suggestions from Rob Herring.
- Define "maxItems: 1" in dmic-gpios property.
- Only keep one example and add dmic-gpios property in.
v5:
- Machine driver:
- Fix a format string warning (Reported-by: kernel test robot <lkp@intel.com>).
detailed info at https://lore.kernel.org/patchwork/patch/1331087/
v4:
- Machine driver: Addressed suggestions from Tzung-Bi.
- Remove redundant judgments in dmic_set() and dmic_get().
- Remove 1 level indent of judgment of IS_ERR(data->dmic_sel).
v3:
- Machine driver: Addressed suggestions from Tzung-Bi.
- Move variables "dmic_switch" and "dmic_sel" into struct sc7180_snd_data.
- Remove redundant judgments in dmic_set().
v2:
- Documentation: Modify the dimc-gpios property description and examples.
- Machine driver:
- Remove "qcom,sc7180-sndcard-rt5682-m98357-2mic" compatible
- See gpio property and use anadditional control.
Thanks for the review!
Ajye Huang (2):
ASoC: google: dt-bindings: modify machine bindings for two MICs case
ASoC: qcom: sc7180: Modify machine driver for 2mic
.../bindings/sound/google,sc7180-trogdor.yaml | 8 ++-
sound/soc/qcom/sc7180.c | 61 +++++++++++++++++++
2 files changed, 68 insertions(+), 1 deletion(-)
--
2.25.1
"Shane.Chien" <shane.chien@mediatek.com>:
From: "Shane.Chien" <shane.chien@mediatek.com>
This series of patches is to fix vaud18 power leakage problem.
vaud18 will be enable only when mt6359 audio path is turned on.
Change since v2:
- fix dt-binnding syntex error
Change since v1:
- use dapm regulator supply widget for vaud18 control.
- add vaud18 regulator property in mt6359 dt-binding.
Shane.Chien (2):
ASoC: Fix vaud18 power leakage of mt6359
dt-bindings: mediatek: mt6359: Add new property for mt6359
.../devicetree/bindings/sound/mt6359.yaml | 9 +++++++
sound/soc/codecs/mt6359.c | 25 +-------------------
sound/soc/codecs/mt6359.h | 8 -------
3 files changed, 10 insertions(+), 32 deletions(-)
--
1.7.9.5
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Document the compatible for SolidRun LX2160A based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
