The target beacon transmission time has to be synced with the HW
TSF when configuring beacon timers in Adhoc mode. Failing to do this
would cause erroneous beacon transmission, for example, on completion
of a scan run to check for IBSS merges.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle multi-interface situations by checking if
AP interfaces are already present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time granularity for the ANI task is different for AP and
station mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for allowing only one IBSS interface to be
configured.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required when issuing commands to the firmware.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use a locally stored reference.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 stores the association state in ieee80211_bss_conf.
Use this and remove the local state, which is incorrect anyway
since it is stored globally and not on a per-VIF basis.
Restarting ANI and reconfiguration of HW beacon timers when a
scan run ends requires more work. This is handled by iterating
over the active interfaces.
Finally, remove the useless check for associated status in RX
processing.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTS protection can be obtained from mac80211 directly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's BSS info can be used for this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition of a station might fail - handle this error
properly by removing the VAP on the target.
Also, bail out immediately if the max. no of interfaces
has been reached.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update capabilites on the target once, when
start() is called, there is no need for redundant
updating on adding an interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple interfaces can be configured if a slot is free
on the target. Monitor mode also requires a slot.
The maximum number of stations that can be handled in
the firmware is 8, manage the station slots accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AR7010 based devices are recognized as storage media.
Sending a CD-EJECT command to the device will 'convert' it into
a WLAN device. Do this within the driver itself, removing the
dependancy on an external program (usb_modeswitch).
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All mwl8k parts perform rate control in firmware. Make this known to
mac80211 so that it does not launch minstrel. Also, because actual tx
rate information is not available from the firmware, invalidate the
rate status before returning the skb to mac80211.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When configuring rx antennas using CMD_RF_ANTENNA, the argument input is
the number of antennas to be enabled. For AP, we support 3 rx antennas
and hence set the field to 3. For tx antennas, value is a bitmap, so 0x7
enables all three.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PS mode of each link according to a bitmap polled from
fw_status. Manually notify mac80211 about PS mode changes in connected
stations.
mac80211 will only be notified about PS start when the station is in PS
and there is a small number of TX blocks from this link ready in HW.
This is required for waking up the remote station since the TIM is
updated entirely by FW.
When a station enters mac80211-PS-mode, we drop all the skbs in the
low-level TX queues belonging to this sta with STAT_TX_FILTERED
to keep our queues clean.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Count the number of FW TX blocks allocated per link. We add blocks to a
link counter when allocated for a TX descriptor. We remove blocks
according to counters in fw_status indicating the number of freed blocks
in FW. These counters are polled after each IRQ.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove an active hlid when chip wakeup fails. In addition rename the
involved functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.
Disable mac80211 automatic link PS-mode handling by supporting
IEEE80211_HW_AP_LINK_PS in HW flags.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Report a TX rate idx of -1 and count 0 when returning untransmitted
skbs to mac80211 using ieee80211_tx_status(). Otherwise mac80211
tries to use the returned (essentially garbage) status.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP-mode we require a per link tx-queue.
This allows us to implement HW assisted PS mode for links,
as well as regulate per-link FW TX blocks consumption.
Split each link into ACs to support future QoS for AP-mode.
AC queues are emptied in priority and per-link queues are
scheduled in a simple round-robin fashion.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a sta starts transmitting immediately after authentication, sometimes
the FW deauthenticates it. Fix this by marking the sta "in-connection"
in FW before sending the autentication response.
The "in-connection" entry is automatically removed when connection
succeeds or after a timeout.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Check the conditions for the high/low TX queue watermarks when the
spin-lock is taken. This prevents race conditions as tx_queue_count and
the flag checked are only modified when the spin-lock is taken.
The following race was in mind:
- Queues are almost full and wl1271_op_tx() will stop the queues, but it
doesn't get the spin-lock yet.
- (on another CPU) tx_work_locked() dequeues 15 skbs from this queue and
tx_queue_count is updated to reflect this
- wl1271_op_tx() does not check tx_queue_count after taking the
spin-lock and incorrectly stops the queue.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The mac_address should be set also when ht caps are disabled.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the standard ALIGN() macro instead of redefining similar macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx fw supports ack status reporting for tx frames, so
add the IEEE80211_HW_REPORTS_TX_ACK_STATUS flag to our supported
features.
Since we do the rate control in the fw, we'll probably want
to adjust the STA_LOST_PKT_THRESHOLD heuristics in the future, to
account for retransmissions as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some blocking functions were called while holding the rcu lock for
accessing STA information. This can lead to a deadlock.
Save the required info beforehand and release the rcu without
blocking.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
for debugging purposes, wl12xx determines whether a rx packet
is a beacon packet.
however, it checks only the frame_control subtype without checking
the actual packet type, which leads to false identification in some
cases.
use ieee80211_is_beacon instead.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In revision > 6.1.3.0.0 the firmware expects memory configuration command
as part of boot. This was missing if driver boots in PLT mode.
The patch adds the memory configuration command, which fixes PLT commands
tx continuous and rx statistics.
Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ret is used to store int types. Using an u8 will break the error
handling.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Linux-next as of 20110217 complains when building for OMAP1.
LD vmlinux
`hci_sock_cleanup' referenced in section `.init.text' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
`hci_sock_cleanup' referenced in section `.init.text' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
make: *** [vmlinux] Error 1
A recent patch by Gustavo (Bluetooth: Merge L2CAP and SCO modules
into bluetooth.ko) introduced this by calling the hci_sock_cleanup
function in the error path of bt_init.
Fix this by dropping the __exit marking for hci_sock_cleanup.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch prevents a crash when remote host tries to create a LE
link which already exists. i.e.: call l2test twice passing the
same parameters.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET"
added an extra udelay to the reset routine. As the required
delay is already present, remove this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new RT5390 chip support
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revise/Add GPIO register related definitions
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the definition of protection related registers more precisely
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e81e0aef32 "rt2x00 : avoid
timestamp for monitor injected frame." as it breaks proper timestamp insertion
into probe responses injected by hostapd for example.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Benoit PAPILLAULT <benoit.papillault@free.fr>
Cc: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only devices that don't have RTS/CTS offload need to check for
IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT.
By swapping both conditions we keep the same number of needed conditionals
for devices without RTS/CTS offload but save one conditional on devices
with RTS/CTS offload.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_PWR_CFG_* setting need to consider below cases
-compesate 20M/40M tx power delta for 2.4/5GHZ band
-limit maximum EIRP tx power to power_level of
regulatory requirement
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select
default antenna using gpio control way even if we do not turn on
antenna diversity feature.
Seperate the meaning of TX/RX chain and antenna. Some chips use
2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain
but may have 2 RX antennas to do antenna diversity.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code has many macros that are no longer needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
