This patch adds support for a per-target dm_flush_fn method. This is needed
to allow dm-loop to invalidate page cache mappings in response to BLKFLSBUF
ioctl commands.
Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate the setting of device I/O limits from dm_get_device(). dm-loop will
use this.
Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found a problem within device-mapper that occurs in low-mem situations. It
was found using a mirror target but I think in theory it would hit any setup
that stacks device-mapper devices (like LVM on top of multipath).
Since device-mapper core uses the common fs_bioset in clone_bio(), and a
private, but still global, bio_set in split_bvec() it is possible that the
filesystem and the first level target successfully get bios but the lower
level target doesn't because there is no more memory and the pool was drained
by upper layers. So the remapping will be stuck forever. To solve this
device-mapper core needs to use a private bio_set for each device.
Signed-off-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the low memory situation dm-crypt needs to use a private mempool of bios to
avoid blocking.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is designed to help dm-crypt comply with the
new constraints imposed by the following patch in -mm:
md-dm-reduce-stack-usage-with-stacked-block-devices.patch
Under low memory the existing implementation relies upon waiting for I/O
submitted recursively to generic_make_request() completing before the original
generic_make_request() call can return.
This patch moves the I/O submission to a workqueue so the original
generic_make_request() can return immediately.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restructure the dm-crypt write processing in preparation for workqueue changes
in the next patches.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restructure part of the dm-crypt code in preparation for workqueue changes.
Use 'base_bio' or 'clone' variable names consistently throughout. No
functional changes are included in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the facility to wipe the encryption key from memory (for example while a
laptop is suspended) and reinstate it later (when the laptop gets resumed).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a target preresume hook.
It is called before the targets are resumed and if it returns an error the
resume gets cancelled.
The crypt target will use this to indicate that it is unable to process I/O
because no encryption key has been supplied.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Device-mapper devices are not accessible until a 'resume' ioctl has been
issued. For userspace to find out when this happens we need to generate an
uevent for udev to take appropriate action.
As discussed at OLS we should send 'change' events for 'resume'. We can think
of no useful purpose served by also having 'suspend' events.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After initialising m->ti, there's no need to pass it in subsequent calls to
static functions used for parsing parameters.
Signed-off-by: Micha³ Miros³aw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove trailing space from 'dmsetup table' output.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a snapshot became invalid while there are outstanding pending_exceptions,
when pending_complete() processes each one it forgets to remove the
corresponding exception from its exception table before freeing it.
Fix this by moving the 'out:' label up one statement so that
remove_exception() is always called. Then __invalidate_exception() no longer
needs to call it and its 'pe' argument become superfluous.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename sibling_count to ref_count and introduce get and put functions.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a workqueue so that I/O can be queued up to be flushed from a separate
thread (e.g. if local interrupts are disabled).
A new per-snapshot spinlock pe_lock is introduced to protect queued_bios.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rearranges the pending_complete() code so that the functional
changes in subsequent patches are clearer.
By consolidating the error and the non-error paths, we can move
error_snapshot_bios() and __flush_bios() in line.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rearranges the snapshot_map code so that the functional changes in
subsequent patches are clearer.
The only functional change is to replace the existing read lock with a write
lock which the next patch needs.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When suspending a device-mapper device, dm_suspend() sleeps until all
necessary I/O is completed. This state is triggered by a callback from
persistent_commit(). But some I/O can still be issued *after* the callback
(to prepare the next metadata area for use if the current one is full). This
patch delays the callback until after that I/O is complete.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
read_exception() and write_exception() only return an error if supplied with
an out-of-range index. If this ever happens it's the result of a bug in the
calling code so we handle this with an assertion and remove the error handling
in the callers.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the error handling when store.read_metadata is called: the error should be
returned immediately.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The chunk size of snapshots cannot be changed so it is redundant to require it
as a parameter when activating an existing snapshot. Allow a value of zero in
this case and ignore it. For a new snapshot, use a default value if zero is
specified.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While reading the code I found a bug in the error path in alloc_dev in dm.c
When blk_alloc_queue fails there is no call to free_minor.
This patch fixes the problem.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new ioctl code passes the wrong file pointer to the underlying device.
No file pointer is available so make a temporary fake one.
ioctl_by_bdev() does set_fs(KERNEL_DS) so it's for ioctls originating
within the kernel and unsuitable here. We are processing ioctls that
originated in userspace and mapping them to different devices. Fixing the
existing callers that pass a NULL file struct and consolidating the
fake_file users are separate matters to solve in later patches.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export blkdev_driver_ioctl for device-mapper.
If we get as far as the device-mapper ioctl handler, we know the ioctl is not
a standard block layer BLK* one, so we don't need to check for them a second
time and can call blkdev_driver_ioctl() directly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an ioctl is performed on a multipath device simply pass it on to the
underlying block device through current_path. If current path is not yet
selected, select it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an ioctl is performed on a device with a linear target, simply pass it on
to the underlying block device.
Note that the ioctl will pass through the filtering in blkdev_ioctl() twice.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the core device-mapper infrastructure to accept arbitrary ioctls on a
mapped device provided that it has exactly one target and it is capable of
supporting ioctls.
[We can't use unlocked_ioctl because we need 'inode': 'file' might be NULL.
Is it worth changing this?]
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Arnd Bergmann <arnd@arndb.de> wrote:
> Am Wednesday 21 June 2006 21:31 schrieb Alasdair G Kergon:
> > static struct block_device_operations dm_blk_dops = {
> > .open = dm_blk_open,
> > .release = dm_blk_close,
> > +.ioctl = dm_blk_ioctl,
> > .getgeo = dm_blk_getgeo,
> > .owner = THIS_MODULE
>
> I guess this also needs a ->compat_ioctl method, otherwise it won't
> work for ioctl numbers that have a compat_ioctl implementation in the
> low-level device driver.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Just some minor comment nits.
- little-endian is better than low-endian
- and since it is called essiv everywere it should also be essiv
in the comments (and not ess_iv)
Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts dm-crypt to use the new block cipher type where
applicable. It also changes simple cipher operations to use the new
encrypt_one/decrypt_one interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need to be careful when referencing mirrors[i].rdev. It can disappear
under us at various times.
So:
fix a couple of problem places.
comment a couple of non-problem places
move an 'atomic_add' which deferences rdev down a little
way to some where where it is sure to not be NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch broke the ability to do a user-request check of a raid1.
This patch fixes the breakage and also moves a comment that was dislocated
by the same patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we
- shut down a clean array,
- restart with one (or more) drive(s) missing
- make some changes
- pause, so that they array gets marked 'clean',
the event count on the superblock of included drives
will be the same as that of the removed drives.
So adding the removed drive back in will cause it
to be included with no resync.
To avoid this, we only update the eventcount backwards when the array
is not degraded. In this case there can (should) be no non-connected
drives that we can get confused with, and this is the particular case
where updating-backwards is valuable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On an nForce4-equipped machine with two SATA disk in raid1 setup using dmraid,
we experienced frequent deadlock of the system under high i/o load. 'cat
/dev/zero > ~/zero' was the most reliable way to reproduce them: Randomly
after a few GB, 'cp' would be left in 'D' state along with kjournald and
kmirrord. The functions cp and kjournald were blocked in did vary, but
kmirrord's wchan always pointed to 'mempool_alloc()'. We've seen this pattern
on 2.6.15 and 2.6.17 kernels. http://lkml.org/lkml/2005/4/20/142 indicates
that this problem has been around even before.
So much for the facts, here's my interpretation: mempool_alloc() first tries
to atomically allocate the requested memory, or falls back to hand out
preallocated chunks from the mempool. If both fail, it puts the calling
process (kmirrord in this case) on a private waitqueue until somebody refills
the pool. Where the only 'somebody' is kmirrord itself, so we have a
deadlock.
I worked around this problem by falling back to a (blocking) kmalloc when
before kmirrord would have ended up on the waitqueue. This defeats part of
the benefits of using the mempool, but at least keeps the system running. And
it could be done with a two-line change. Note that mempool_alloc() clears the
GFP_NOIO flag internally, and only uses it to decide whether to wait or return
an error if immediate allocation fails, so the attached patch doesn't change
behaviour in the non-deadlocking case. Path is against current git
(2.6.18-rc4), but should apply to earlier versions as well. I've tested on
2.6.15, where this patch makes the difference between random lockup and a
stable system.
Signed-off-by: Daniel Kobras <kobras@linux.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch that allowed linear arrays to be reconfigured on-line
allowed in a bug which results in divide by zero - not all
mddev->array_size were converted to conf->array_size.
This patch finished the conversion and fixed the bug.
The offending patch was commit 7c7546ccf6.
Thanks to Simon Kirby <sim@netnation.com> for the bug report.
Cc: Simon Kirby <sim@netnation.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers. Fix.
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places we use number (0660) someplaces names (S_IRUGO). Change all
numbers to be names, and change 0655 to be what it should be.
Also make some formatting more consistent.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has to be done in ->load_super, not ->validate_super
Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator.
Effects on non-lockdep kernels:
- the introduction of the following function variants:
extern struct block_device *open_partition_by_devnum(dev_t, unsigned);
extern int blkdev_put_partition(struct block_device *);
static int
blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags);
which on non-lockdep are the same as open_by_devnum(), blkdev_put()
and blkdev_get().
- a subclass parameter to do_open(). [unused on non-lockdep]
- a subclass parameter to __blkdev_put(), which is a new internal
function for the main blkdev_put*() functions. [parameter unused
on non-lockdep kernels, except for two sanity check WARN_ON()s]
these functions carry no semantical difference - they only express
object dependencies towards the lockdep subsystem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RAID5 recently changed to RAID456
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus... (and fly spell found more).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size calculation made assumtion which the new offset mode didn't
follow. This gets the size right in all cases.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix problems with new bmap based access to bitmap files.
1/ When not using a file based bitmap, attach a NULL list of buffers
to each page so the common free_buffer routine can cope.
2/ Use submit_bh to read as well as write, rather than vfs_read.
This makes read and write more symetric.
3/ sync the file before reading, to ensure that the page cache has no
dirty pages that might get written out later.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out. I don't believe this is a supportable
approach.
This patch changes the approach to use the same approach as swap files. i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.
swapfile only uses parts of the file that provide a full pages at contiguous
addresses. We don't have that luxury so we have to cope with pages that are
non-contiguous in storage. To handle this we attach buffers to each page, and
store the addresses in those buffers.
With this approach the pagecache may contain data which is inconsistent with
what is on disk. To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file. If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used. And new version of mdadm will have support for this.
This approach simplifies a lot of code:
- we no longer need to keep a list of pages which we need to wait for,
as the b_endio function can keep track of how many outstanding
writes there are. This saves a mempool.
- -EAGAIN returns from write_page are no longer possible (not sure if
they ever were actually).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it. The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.
This patch tidies that up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_active is never called, and the BITMAP_ACTIVE flag is never users or
tested, so discard them both.
Also remove some out-of-date 'todo' comments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap gets a collection of pages representing the bitmap when it
initialises the bitmap, and puts all the references when discarding the
bitmap.
It also occasionally takes extra references without any good reason, and
sometimes drops them ... though it doesn't always drop them, which can result
in a memory leak.
This patch removes the unnecessary 'get_page' calls, and the corresponding
'put_page' calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular, this means that we use 4 bits per page instead of a whole
unsigned long.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap has some attributes per-page. Handling of these attributes in
largely abstracted in set_page_attr and clear_page_attr. However
get_page_attr exposes the format used to store them. So prior to changing
that format, introduce test_page_attr instead of get_page_attr, and make
appropriate usage changes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).
However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work. The same result can be
achieved by doing the waiting directly in bitmap_unplug.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).
The file also wasn't closed if adding the bitmap file failed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as raid5 sync_request is WAY too big.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes. e.g.
A B C D
D A B C
E F G H
H E F G
(columns are drives, rows are stripes, LETTERS are chunks of data).
This is similar to raid10's 'far' mode, but not quite the same. So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.
So remove the message for non-active arrays.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
This delay turns out to be too short for some real workloads. So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning was slightly useful back in 2.2 days, but is more an annoyance
now. It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change made this goto unnecessary, so reformat the code to make it
clearer what is happening.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy device-mapper error messages to include context information
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you misuse the device-mapper interface (or there's a bug in your userspace
tools) it's possible to end up with 'unlinked' mapped devices that cannot be
removed until you reboot (along with uninterruptible processes).
This patch prevents you from removing a device that is still open.
It introduces dm_lock_for_deletion() which is called when a device is about to
be removed to ensure that nothing has it open and nothing further can open it.
It uses a private open_count for this which also lets us remove one of the
problematic bdget_disk() calls elsewhere.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a library function dm_create_error_table() to create a table that rejects
any I/O sent to a device with EIO.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move definitions of core device-mapper functions for manipulating mapped
devices and their tables to <linux/device-mapper.h> advertising their
availability for use elsewhere in the kernel.
Protect the contents of device-mapper.h with ifdef __KERNEL__. And throw
in a few formatting clean-ups and extra comments.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge dm_create() and dm_create_with_minor() by introducing the special value
DM_ANY_MINOR to request the allocation of the next available minor number.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return sense if dm_split_args is called with a NULL input parameter.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kcopyd should accumulate errors - otherwise I/O failures may be ignored
unintentionally.
And invert 'success' (used in a future patch), using a more intuitive
!(read_err || write_err).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a mirror is reduced in size, clear the part of the bitmap that is no
longer used.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the 'sizeof' in the region log bitmap size calculation: it's uint32_t, not
unsigned long - this breaks on some archs.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refactor the code that creates the core and disk log contexts to avoid the
repeated allocation of clean_bits introduced by the last patch.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On-disk logs for dm-mirror devices are currently hard-coded to use 512 byte
hard-sector-sizes. This patch fixes dm-log so it will work with devices with
non-512-byte hard-sector-sizes.
To maintain full compatibility, instead of moving the clean-bits bitset to a
bitset, and enlarges the disk-header buffer to encompass both the header and
the bitset. The I/O routines for the bitset are removed, and the I/O routines
for the disk-header now also read/write the bitset.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The table is indexed from 0, so an index equal to t->num_targets should be
rejected.
(There is no code in the current tree that would exercise this bug.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The device-mapper core does not perform any remapping of bios before passing
them to the targets. If a particular mapping begins part-way into a device,
targets obtain the sector relative to the start of the mapping by subtracting
ti->begin.
The dm-raid1 target didn't do this everywhere: this patch fixes it, taking
care to subtract ti->begin exactly once for each bio.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In alloc_dev(), we register the device with the block layer and then continue
to initialize the device. But register_disk() makes the device available to
be opened before we have completed initialising it.
This patch moves the final bits of the initialization above the disk
registration.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reference counting on dm-mod is zero if no mapped devices are open. This
is incorrect, and can lead to an oops if the module is unloaded while mapped
devices exist.
This patch claims a reference to the module whenever a device is created, and
drops it again when the device is freed.
Devices must be removed before dm-mod is unloaded.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid races, _minor_lock must be held while changing mapped device
reference counts.
There are a few paths where a mapped_device pointer is returned before a
reference is taken. This patch fixes them.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a chicken and egg problem between the block layer and dm in which the
gendisk associated with a mapping keeps a reference-less pointer to the
mapped_device.
This patch uses a new flag DMF_FREEING to indicate when the mapped_device is
no longer valid. This is checked to prevent any attempt to open the device
from succeeding while the device is being destroyed.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While removing a device, another another thread might attempt to resurrect it.
This patch replaces the _minor_lock mutex with a spinlock and uses
atomic_dec_and_lock() to serialize reference counting in dm_put().
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
idr_pre_get() can sleep while allocating memory.
The next patch will change _minor_lock into a spinlock, so this patch moves
idr_pre_get() outside the lock in preparation.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One part of the system can attempt to use a mapped device before another has
finished initialising it or while it is being freed.
This patch introduces a place holder value, MINOR_ALLOCED, to mark the minor
as allocated but in a state where it can't be used, such as mid-allocation or
mid-free. At the end of the initialization, it replaces the place holder with
the pointer to the mapped_device, making it available to the rest of the dm
subsystem.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Persistent snapshots currently store a private copy of the chunk size.
Userspace also supplies the chunk size when loading a snapshot. Ensure
consistency by only storing the chunk_size in one place instead of two.
Currently the two sizes will differ if the chunk size supplied by userspace
does not match the chunk size an existing snapshot actually uses. Amongst
other problems, this causes an incorrect 'percentage full' to be reported.
The patch ensures consistency by only storing the chunk_size in one place,
removing it from struct pstore. Some initialisation is delayed until the
correct chunk_size is known. If read_header() discovers that the wrong chunk
size was supplied, the 'area' buffer (which the header already got read into)
is reinitialised to the correct size.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a NULL dereference spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
otherwise we get nasty messages about locks not being released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This loop that sets up the hash_table has problems.
Careful examination will show that the last time through, everything but
the first line is pointless. This is because all it does is change 'cur'
and 'size' and neither of these are used after the loop. This should ring
warning bells... That last time through the loop,
size += conf->strip_zone[cur].size
can index off the end of the strip_zone array. Depending on what it finds
there, it might exit the loop cleanly, or it might spin going further and
further beyond the array until it hits an unmapped address.
This patch rearranges the code so that the last, pointless, iteration of
the loop never happens. i.e. the one statement of the last loop that is
needed is moved the the end of the previous loop - or to before the loop
starts - and the loop counter starts from 1 instead of 0.
Cc: "Don Dupuis" <dondster@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
reshape_position is a 64bit field that was not 64bit aligned. So swap with
new_level.
NOTE: this is a user-visible change. However:
- The bad code has not appeared in a released kernel
- This code is still marked 'experimental'
- This only affects version-1 superblock, which are not in wide use
- These field are only used (rather than simply reported) by user-space
tools in extemely rare circumstances : after a reshape crashes in the
first second of the reshape process.
So I believe that, at this stage, the change is safe. Especially if people
heed the 'help' message on use mdadm-2.4.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors. However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... being careful that mutex_trylock is inverted wrt down_trylock
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a write due to barrier failure, we don't reset 'remaining', so
it goes negative and never hits 0 again.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An md array can be asked to change the amount of each device that it is using,
and in particular can be asked to use the maximum available space. This
currently only works if the first device is not larger than the rest. As
'size' gets changed and so 'fit' becomes wrong. So check if a 'fit' is
required early and don't corrupt it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
raid5 overloads bi_phys_segments to count the number of blocks that the
request was broken in to so that it knows when the bio is completely handled.
Accessing this must always be done under a spinlock. In one case we also call
bi_end_io under that spinlock, which probably isn't ideal as bi_end_io could
be expensive (even though it isn't allowed to sleep).
So we reducde the range of the spinlock to just accessing bi_phys_segments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wait_event_lock_irq puts a ';' after its usage of the 4th arg, so we don't
need to.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows reshape to be triggerred via sysfs (which is the only way to start
it happening).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of checkpointing at each stripe, only checkpoint when a new write
would overwrite uncheckpointed data. Block any write to the uncheckpointed
area. Arbitrarily checkpoint at least every 3Meg.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds raid5_reshape and end_reshape which will start and finish the
reshape processes.
raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage
accidental use.
Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry.
and Make sure that you have backups, just in case.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to allow that different stripes are of different effective sizes, and
use the appropriate size. Also, when a stripe is being expanded, we must
block any IO attempts until the stripe is stable again.
Key elements in this change are:
- each stripe_head gets a 'disk' field which is part of the key,
thus there can sometimes be two stripe heads of the same area of
the array, but covering different numbers of devices. One of these
will be marked STRIPE_EXPANDING and so won't accept new requests.
- conf->expand_progress tracks how the expansion is progressing and
is used to determine whether the target part of the array has been
expanded yet or not.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remainder of this batch implements raid5 reshaping. Currently the only
shape change that is supported is added a device, but it is envisioned that
changing the chunksize and layout will also be supported, as well as changing
the level (e.g. 1->5, 5->6).
The reshape process naturally has to move all of the data in the array, and so
should be used with caution. It is believed to work, and some testing does
support this, but wider testing would be great for increasing my confidence.
You will need a version of mdadm newer than 2.3.1 to make use of raid5 growth.
This is because mdadm need to take a copy of a 'critical section' at the
start of the array incase there is a crash at an awkward moment. On restart,
mdadm will restore the critical section and allow reshape to continue.
I hope to release a 2.4-pre by early next week - it still needs a little more
polishing.
This patch:
Previously the array of disk information was included in the raid5 'conf'
structure which was allocated to an appropriate size. This makes it awkward
to change the size of that array. So we split it off into a separate
kmalloced array which will require a little extra indexing, but is much easier
to grow.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
status_resync - used by /proc/mdstat to report the status of a resync, assumes
that device sizes will always fit into an 'unsigned long' This is no longer
the case...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are counting failed devices twice, once of the device that is failed, and
once for the hole that has been left in the array. Remove the former so
'failed' matches 'missing'. Storing these counts in the superblock is a bit
silly anyway....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I really should make this a function of the personality....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This flag should be set for a virtual device iff it is set for all underlying
devices.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use bd_claim_by_disk.
Following symlinks are created if dm-0 maps to sda:
/sys/block/dm-0/slaves/sda --> /sys/block/sda
/sys/block/sda/holders/dm-0 --> /sys/block/dm-0
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use bd_claim_by_disk.
Following symlinks are created if md0 is built from sda and sdb
/sys/block/md0/slaves/sda --> /sys/block/sda
/sys/block/md0/slaves/sdb --> /sys/block/sdb
/sys/block/sda/holders/md0 --> /sys/block/md0
/sys/block/sdb/holders/md0 --> /sys/block/md0
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow drive geometry to be stored with a new DM_DEV_SET_GEOMETRY ioctl.
Device-mapper will now respond to HDIO_GETGEO. If the geometry information is
not available, zero will be returned for all of the parameters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Store an up-pointer to the owning struct mapped_device in every table when it
is created.
Access it with:
struct mapped_device *dm_table_get_md(struct dm_table *t)
Tables linked to md must be destroyed before the md itself.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change dm_get_mdptr() to take a struct mapped_device instead of dev_t.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch stores a printable device number in struct mapped_device for use in
warning messages and with a proposed netlink interface.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If dm_suspend() is cancelled, bios already added to the deferred list need to
be submitted. Otherwise they remain 'in limbo' until there's a dm_resume().
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before removing a snapshot, wait for the completion of any kcopyd jobs using
it.
Do this by maintaining a count (nr_jobs) of how many outstanding jobs each
kcopyd_client has.
The snapshot destructor first unregisters the snapshot so that no new kcopyd
jobs (created by writes to the origin) will reference that particular
snapshot. kcopyd_client_destroy() is now run next to wait for the completion
of any outstanding jobs before the snapshot exception structures (that those
jobs reference) are freed.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This flag should be set for a virtual device iff it is set for all
underlying devices.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't know what type sector_t has. Sometimes it's unsigned long, sometimes
it's unsigned long long. For example on ppc64 it's unsigned long with
CONFIG_LBD=n and on x86_64 it's unsigned long long with CONFIG_LBD=n.
The way to handle all of this is to always use unsigned long long and to
always typecast the sector_t when printing it.
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dm-mirror has potential data corruption problem: while on-disk log shows
that all disk contents are in-sync, actual contents of the disks are not
synchronized. This problem occurs if initial recovery (synching) is
interrupted and resumed.
Attached patch fixes this problem.
Background:
rh_dec() changes the region state from RH_NOSYNC (out-of-sync) to RH_CLEAN
(in-sync), which results in the corresponding bit of clean_bits being set.
This is harmful if on-disk log is used and the map is removed/suspended
before the initial sync is completed. The clean_bits is written down to
the on-disk log at the map removal, and, upon resume, it's read and copied
to sync_bits. Since the recovery process refers to the sync_bits to find a
region to be recovered, the region whose state was changed from RH_NOSYNC
to RH_CLEAN is no longer recovered.
If you haven't applied dm-raid1-read-balancing.patch proposed in dm-devel
sometimes ago, the contents of the mirrored disk just corrupt silently. If
you have, balanced read may get bogus data from out-of-sync disks.
The patch keeps RH_NOSYNC state unchanged. It will be changed to
RH_RECOVERING when recovery starts and get reclaimed when the recovery
completes. So it doesn't leak the region hash entry.
Description:
Keep RH_NOSYNC state unchanged when I/O on the region completes.
rh_dec() changes the region state from RH_NOSYNC (out-of-sync) to RH_CLEAN
(in-sync), which results in the corresponding bit of clean_bits being set.
This is harmful if on-disk log is used and the map is removed/suspended
before the initial sync is completed. The clean_bits is written down to
the on-disk log at the map removal, and, upon resume, it's read and copied
to sync_bits. Since the recovery process refers to the sync_bits to find a
region to be recovered, the region whose state was changed from RH_NOSYNC
to RH_CLEAN is no longer recovered.
If you haven't applied dm-raid1-read-balancing.patch proposed in dm-devel
sometimes ago, the contents of the mirrored disk just corrupt silently. If
you have, balanced read may get bogus data from out-of-sync disks.
The RH_NOSYNC region will be changed to RH_RECOVERING when recovery starts
on the region and get reclaimed when the recovery completes. So it doesn't
leak the region hash entry.
Alasdair said:
I've analysed the relevant part of the state machine and I believe that
the patch is correct.
(Further work on this code is still needed - this patch has the
side-effect of holding onto memory unnecessarily for long periods of time
under certain workloads - but better that than corrupting data.)
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a snapshot becomes invalid, s->valid is set to 0. In this state, a
snapshot can no longer be accessed.
When s->lock is acquired, before doing anything else, s->valid must be checked
to ensure the snapshot remains valid.
This patch eliminates some races (that may cause panics) by adding some
missing checks. At the same time, some unnecessary levels of indentation are
removed and snapshot invalidation is moved into a single function that always
generates a device-mapper event.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The siblings "list" is used unsafely at the moment.
Firstly, only the element on the list being changed gets locked (via the
snapshot lock), not the next and previous elements which have pointers that
are also being changed.
Secondly, if you have two or more snapshots and write to the same chunk a
second time before every snapshot has finished making its private copy of the
data, if you're unlucky, _origin_write() could attempt its list_merge() and
dereference a 'last' pointer to a pending_exception structure that has just
been freed.
Analysis reveals that the list is actually only there for reference counting.
If 5 pending_exceptions are needed in origin_write, then the 5 are joined
together into a 5-element list - without a separate list head because there's
nowhere suitable to store it. As the pending_exceptions complete, they are
removed from the list one-by-one and any contents of origin_bios get moved
across to one of the remaining pending_exceptions on the list. Whichever one
is last is detected because list_empty() is then true and the origin_bios get
submitted.
The fix proposed here uses an alternative reference counting mechanism by
choosing one of the pending_exceptions as primary and maintaining an atomic
counter there.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Say you have several snapshots of the same origin and then you issue a write
to some place in the origin for the first time.
Before the device-mapper snapshot target lets the write go through to the
underlying device, it needs to make a copy of the data that is about to be
overwritten. Each snapshot is independent, so it makes one copy for each
snapshot.
__origin_write() loops through each snapshot and checks to see whether a copy
is needed for that snapshot. (A copy is only needed the first time that data
changes.)
If a copy is needed, the code allocates a 'pending_exception' structure
holding the details. It links these together for all the snapshots, then
works its way through this list and submits the copying requests to the kcopyd
thread by calling start_copy(). When each request is completed, the original
pending_exception structure gets freed in pending_complete().
If you're very unlucky, this structure can get freed *before* the submission
process has finished walking the list.
This patch:
1) Creates a new temporary list pe_queue to hold the pending exception
structures;
2) Does all the bookkeeping up-front, then walks through the new list
safely and calls start_copy() for each pending_exception that needed it;
3) Avoids attempting to add pe->siblings to the list if it's already
connected.
[NB This does not fix all the races in this code. More patches will follow.]
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
drivers/char/ftape/lowlevel/fdc-io.c: Correct a comment
Kconfig help: MTD_JEDECPROBE already supports Intel
Remove ugly debugging stuff
do_mounts.c: Minor ROOT_DEV comment cleanup
BUG_ON() Conversion in drivers/s390/block/dasd_devmap.c
BUG_ON() Conversion in mm/mempool.c
BUG_ON() Conversion in mm/memory.c
BUG_ON() Conversion in kernel/fork.c
BUG_ON() Conversion in ipc/sem.c
BUG_ON() Conversion in fs/ext2/
BUG_ON() Conversion in fs/hfs/
BUG_ON() Conversion in fs/dcache.c
BUG_ON() Conversion in fs/buffer.c
BUG_ON() Conversion in input/serio/hp_sdc_mlc.c
BUG_ON() Conversion in md/dm-table.c
BUG_ON() Conversion in md/dm-path-selector.c
BUG_ON() Conversion in drivers/isdn
BUG_ON() Conversion in drivers/char
BUG_ON() Conversion in drivers/mtd/
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes a mempool user, which is basically just a wrapper around
kzalloc(), to use the common mempool_kmalloc/kfree, rather than its own
wrapper function, removing duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes several mempool users, all of which are basically just
wrappers around kmalloc(), to use the common mempool_kmalloc/kfree, rather
than their own wrapper function, removing a bunch of duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert two mempool users that currently use their own mempool-backed page
allocators to use the generic mempool page allocator.
Also included are 2 trivial whitespace fixes.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
We dereference bitmap both one line above and one line below this check
rendering this check quite useless.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The code that handles bios that span table target boundaries by breaking
them up into smaller bios will not split an individual struct bio_vec into
more than two pieces. Sometimes more than that are required.
This patch adds a loop to break the second piece up into as many pieces as
are necessary.
Cc: "Abhishek Gupta" <abhishekgupt@gmail.com>
Cc: Dan Smith <danms@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dm-stripe target currently does not enforce that the size of a stripe
device be a multiple of the chunk-size. Under certain conditions, this can
lead to I/O requests going off the end of an underlying device. This
test-case shows one example.
echo "0 100 linear /dev/hdb1 0" | dmsetup create linear0
echo "0 100 linear /dev/hdb1 100" | dmsetup create linear1
echo "0 200 striped 2 32 /dev/mapper/linear0 0 /dev/mapper/linear1 0" | \
dmsetup create stripe0
dd if=/dev/zero of=/dev/mapper/stripe0 bs=1k
This will produce the output:
dd: writing '/dev/mapper/stripe0': Input/output error
97+0 records in
96+0 records out
And in the kernel log will be:
attempt to access beyond end of device
dm-0: rw=0, want=104, limit=100
The patch will check that the table size is a multiple of the stripe
chunk-size when the table is created, which will prevent the above striped
device from being created.
This should not affect tools like LVM or EVMS, since in all the cases I can
think of, striped devices are always created with the sizes being a
multiple of the chunk-size.
The size of a stripe device must be a multiple of its chunk-size.
(akpm: that typecast is quite gratuitous)
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- wrong test for 'is this a BARRIER bio'
- not freeing on all possible paths.
- using r1_bio after freeing it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor number should be freed after del_gendisk(). Otherwise, there could
be a window where 2 registered gendisk has same minor number.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to unfreeze and release bdev otherwise the bdev inode with
inconsistent state is reused later and cause problem.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sometimes it doesn't so make the code more like the version-0 code which
works.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- version-1 superblock
+ The default_bitmap_offset is in sectors, not bytes.
+ the 'size' field in the superblock is in sectors, not KB
- raid0_run should return a negative number on error, not '1'
- raid10_read_balance should not return a valid 'disk' number if
->rdev turned out to be NULL
- kmem_cache_destroy doesn't like being passed a NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mdu_array_info_t->size is 'int', which isn't big enough for the size (in KB of
each component in) some arrays.
So rather than a random overflow, set size to -1 when it cannot be set
correctly.
To update aspect on an array, userspace will sometimes:
get_array_info
change one field
set_array_info
in this case, we don't want the '-1' in 'size' to change to size, or look like
a size change at all. So test for that in update_array_info.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fix to the device-mapper-log-bitset-fix-endian patch that
switched to ext2_* versions of the set and clear bit functions. The
find_next_zero_bit function also has to be the ext2 one. Otherwise the
mirror target tries to recover non-existent regions beyond the end of
device.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
.. just as we already have for raid5.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While a read-only array doesn't not really need a bitmap, we should
not remove the bitmap when switching an array to read-only because
a/ There is no code to re-add the bitmap which switching to read-write,
b/ There is insufficient locking - the bitmap could be accessed while it is
being removed.
Cc: Reuben Farrelly <reuben-lkml@reub.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
super_1_sync only updates fields in the superblock that might have changed.
'raid_disks' and 'size' could have changed, but this information doesn't get
updated.... until this patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As 'array_size' is a 'sector_t', it may overflow inappropriately when shifted
10 bits. So We should cast it to a loff_t first.
There are two places with this problem, but the second (in update_raid_disks)
isn't needed so just remove it:
The only personality that handles ->reshape currently is raid1,
and it doesn't change the size of the array.
When added for raid5/6, reshape again won't change the size of the array,
at least not straight away.
This code might be need for reshaping 'linear' but linear->shape,
if implemented, should probably do the i_size_write itself.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The snapshot and origin targets are incapable of handling barriers and need to
indicate this.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Record I/O timing statistics
The start time is added to struct dm_io, an existing structure allocated
privately internally within dm and attached to each incoming bio.
We export disk_round_stats() from block/ll_rw_blk.c instead of creating a
private clone.
Signed-off-by: Jun'ichi "Nick" Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Record basic I/O statistics for mapped devices.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce substantially the amount of code using PF_MEMALLOC, as envisaged in the
original FIXME.
If you're using lvm2, for this patch to work correctly you should update to
lvm2 version 2.02.01 or later and device-mapper version 1.02.02 or later.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the code responsible for the on-disk mirror logs by using the
set_le_bit test_le_bit functions of ext2. That makes the BE machines keep the
bitmap internally in LE order - it does mean you can't use any other type of
operations on the bitmap words but that looks to be OK in this instance. The
efficiency tradeoff is very minimal as you would expect for something that
ext2 uses.
This allows us to remove bits_to_core(), bits_to_disk() and log->disk_bits.
Also increment the mirror log disk version transparently to avoid sharing with
older kernels that suffered from the 64-bit BE bug.
Signed-off-by: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move snapshot metadata loading to happen when the table is created instead of
when the device is resumed. Writes to the origin device don't trigger
exceptions until each snapshot table becomes active when resume() is called on
each snapshot.
If you're using lvm2, for this patch to work properly you should update to
lvm2 version 2.02.01 or later and device-mapper version 1.02.02 or later.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'level' of an md array can be set as either a number of a string. When
one is set, the other must be marked 'undefined'. This wasn't being done
in one place: where new arrays are created.
Result: if md1 is a raid1, it is stopped and a raid5 is created there, it
might still appear to be a raid1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
e.g. The sx8 driver uses names like sx8/0.
This would make a md component dev name like
/sys/block/md0/md/dev-sx8/0
which is not allowed. So we change the '/' to '!' just like
fs/partitions/check.c(register_disk) does.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DM doesn't need to bounce bio's on its own, but the block layer defaults
to that in blk_queue_make_request(). The lower level drivers should
bounce ios themselves, that is what they need to do if not layered below
dm anyways.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Decrease the number of pointer derefs in drivers/md/multipath.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Alasdair G Kergon <agk@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also export current (average) speed and status in sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Writing major:minor to md/new_dev will bind that device to the array.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/md/md.c: In function `offset_show':
drivers/md/md.c:1670: warning: long long unsigned int format, different type arg (arg 3)
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This the role that a device has in an array can be viewed and set.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the checks - that dev size is never less than array size - into
bind_rdev_to_array to make sure it always happens properly (there is one place
where currently it doesn't).
Also reject any superblock which claims an array size smaller than the device
in question can hold.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If array is active, try to reshape, else just set the value.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow it to be set to a particular version, or 'none'.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... only before array is started of course.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we do a user-requested check/repair, we lose count of the outstanding
requests...
Also make sure that when anything is written to md/sync_action, the
RECOVERY_NEEDED flag is set and the thread is woken up so any changes take
effect.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we update a page_cache page in the kernel, we need to flush_dache_page or
userspace might not see the change.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the needlessly global function md_new_event() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
.. because they aren't used outside md.c
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commands written to sysfs files may, or my not, be \n terminated. We want to
accept with case. For this we use cmd_match.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md sometimes call put_page on NULL pointers (treating it like kfree). This is
not safe, so define and use a 'safe_put_page' which checks for NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel should not be imposing these policy limits: The time between
bitmap updates should certainly be allowed to be more than 15 seconds, and
if someone wants a bitmap chunk size in excess of 4MB, the kernel isn't the
place to stop them.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code to overwrite/reread for addressing read errors in raid1/raid10
currently assumes that the read will not alter the buffer which could be used
to write to the next device. This is not a safe assumption to make.
So we split the loops into a overwrite loop and a separate re-read loop, so
that the writing is complete before reading is attempted.
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).
These personalities have fairly artificial 'numbers'. The numbers
are use to:
1- provide an index into an array where the various personalities
are recorded
2- identify the module (via an alias) which implements are particular
personality.
Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely). Module identification can be done using an alias
based on level rather than 'personality' number.
The current 'raid5' modules support two level (4 and 5) but only one
personality. This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.
With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.
This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
...because that seems to be the preferred practice these days.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- replace open-coded hash chain with hlist macros
- Fix hash-table size at one page - it is already quite generous, so there
will never be a need to use multiple pages, so no need for __get_free_pages
No functional change.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace multiple kmalloc/memset pairs with kzalloc calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Substitute:
page_cache_get -> get_page
page_cache_release -> put_page
PAGE_CACHE_SHIFT -> PAGE_SHIFT
PAGE_CACHE_SIZE -> PAGE_SIZE
PAGE_CACHE_MASK -> PAGE_MASK
__free_page -> put_page
because we aren't using the page cache, we are just using pages.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this patch it is possible to poll /proc/mdstat to detect arrays appearing
or disappearing, to detect failures, recovery starting, recovery completing,
and devices being added and removed.
It is similar to the poll-ability of /proc/mounts, though different in that:
We always report that the file is readable (because face it, it is, even if
only for EOF).
We report POLLPRI when there is a change so that select() can detect
it as an exceptional event. Not only are these exceptional events, but
that is the mechanism that the current 'mdadm' uses to watch for events
(It also polls after a timeout).
(We also report POLLERR like /proc/mounts).
Finally, we only reset the per-file event counter when the start of the file
is read, rather than when poll() returns an event. This is more robust as it
means that an fd will continue to report activity to poll/select until the
program clearly responds to that activity.
md_new_event takes an 'mddev' which isn't currently used, but it will be soon.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add in correct read-error handling for resync and read-only situations.
When read-only, we don't over-write, so we need to mark the failed drive in
the r10_bio so we don't re-try it. During resync, we always read all blocks,
so if there is a read error, we simply over-write it with the good block that
we found (assuming we found one).
Note that the recovery case still isn't handled in an interesting way. There
is nothing useful to do for the 2-copies case. If there are 3 or more copies,
then we could try reading from one of the non-missing copies, but this is a
bit complicated and very rarely would be used, so I'm leaving it for now.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Largely just a cross-port from raid1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are inadvertently setting the R1BIO_Uptodate bit on read errors when we
decide not to try correcting (because there are no other working devices).
This means that the read error is reported to the client as success.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
