Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xnEACgkQMUfUDdst+ylj1QCfaIzUNuFfzTmyB6K6iZrRNhCc
WPgAnRLkkEpI/3rRo7jKwGQsuIuyybUu
=r149
-----END PGP SIGNATURE-----
Merge tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues"
* tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
serial: omap: fix missing comma
serial: sh-sci: Enable the driver on all ARM platforms
serial: mfd: Staticize local symbols
serial: omap: fix a few checkpatch warnings
serial: omap: improve RS-485 performance
mrst_max3110: fix unbalanced IRQ issue during resume
serial: omap: Add support for optional wake-up
serial: sirf: remove duplicate defines
tty: xuartps: Fix build error when COMMON_CLK is not set
tty: xuartps: Fix build error due to missing forward declaration
tty: xuartps: Fix "may be used uninitialized" build warning
serial: 8250_pci: add Pericom PCIe Serial board Support (12d8:7952/4/8) - Chip PI7C9X7952/4/8
tty: xuartps: Update copyright information
tty: xuartps: Implement suspend/resume callbacks
tty: xuartps: Dynamically adjust to input frequency changes
tty: xuartps: Updating set_baud_rate()
tty: xuartps: Force enable the UART in xuartps_console_write
tty: xuartps: support 64 byte FIFO size
tty: xuartps: Add polled mode support for xuartps
tty: xuartps: Implement BREAK detection, add SYSRQ support
...
I worried that the delay of the sdma_run_channel0() maybe too long for
interrupt context, so I added the workqueues for RX/TX DMA.
But tested with bluetooth device, I find that the delay of sdma_run_channel0()
is about 8us (tested in imx6dl sabreauto board). I think the delay
is acceptable.
This patch removes the RX/TX workqueues for DMA, it makes the
code more clear.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dmaengine_tx_status to simplify the code, do not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the (xmit->tail > xmit->head) is true and the xmit->head is 0,
we only need one DMA scatterlist in actually. Current code uses two DMA
scatterlists in this case, this is obviously wrong.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume the following situation:
If the DMA is enabled, and the a TX DMA operation is working,
But we have not issued the TX DMA operation (or we have issued the
TX DMA operation with dma_async_issue_pending(), but the DMA has not
started to move the data from the memory to the TXFIFO).
At this time, we may get the wrong status of the transmitter when we
call the imx_tx_empty. In such situation, only check the USR2_TXDC
does not enough for us.
This patch checks the DMA's situation, and return 0 when the TX DMA is
working.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver does not implement the flush_buffer hook for
uart_ops. When we enable the DMA for the driver, and test it with Bluetooth,
we may meet the following bug for TX:
[1] User application may call the flush operation at any time.
The uart_flush_buffer() calls the uart_circ_clear() to set
the xmit->head and xmit->tail with 0.
[2] The TX DMA callback can be called at any time too.
The dma_tx_call() will update the xmit->tail.
If [2] occurs just after the [1], we will get the wrong xmit->tail.
This patch implements the flush_buffer hook to fix this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f7d2c0bbdb, as it
causes build errors when the driver is built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a warning where resource_size_t is larger than void *:
drivers/tty/serial/imx.c:1542:6: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Since iomem_base is a void *, casting to unsigned long is safe.
It's unclear to me that this comparison is truly needed, but it's there
on several other drivers as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f7d2c0bbd (serial: i.MX: evaluate linux,stdout-path property) introduced
the following sparse warning:
drivers/tty/serial/imx.c:1916:77: warning: Using plain integer as NULL pointer
Pass NULL as the last argument of add_preferred_console() instead of zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The slave_config is not initialized, so some of its fields may
be set with random data which may causes the failure in the following
dmaengine_prep_slave_sg().
This patch fixes this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devicetrees may have the linux,stdout-path property to specify the
console. This patch adds support to the i.MX serial driver for this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only enable the DMA support when the following are meet:
[1] The uart port supports the hardware flow control(CTS/RTS).
(Some uart port does not support the CTS/RTS.)
[2] The application enables the CTS/RTS.
[3] The Soc is imx6q.
For the sdma's firmware limit, we do not support the DMA except
the imx6q platform.
[4] The uart is not used as a console.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was not possible to set custom-baudrates like 62500.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will add the DMA support for the imx uart. For the firmware's limit,
only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can
support the DMA.
This patch adds the necessary macro and helper to distinguish the
imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart"
to enable the DMA support.
This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_console() check makes the clocks(clk_per and clk_ipg) opened
even when we close the console uart.
This patch enable/disable the clocks in imx_console_write(),
so we can keep the clocks closed when the console uart is closed.
Also remove the clock enable/disable oprations in the probe, we do not
need them any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console's clocks are disabled after the uart driver is probed.
It makes that we can see less log from the console now
(though we still can get all the log by the `dmesg`).
So enable the clocks for console, and we can see all the log again.
This patch also disables the sport->clk_per when we fail to enable
the sport->clk_ipg;
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_IMX_CONSOLE is not selected the following build warnings
appear:
drivers/tty/serial/imx.c:274:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:283:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
imx_port_ucrs_save() and imx_port_ucrs_restore() are only used when
CONFIG_CONSOLE_POLL or CONFIG_SERIAL_IMX_CONSOLE are selected, so protect these
functions declaration with a proper ifdef.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code opens the clocks when the uart driver is probed.
This will wastes some power if several uarts are enabled, but not really
used.
So close these clocks for uart, and enable the clocks only when
the uart is used.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart works in the DCE mode by default, but sometime we need it
works at the DTE mode.
This patch adds the support for the DTE mode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only want to enable hardware flow control if RTS/CTS pins
are connected.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the overrun error (ORE) interrupt and increases the
counter in case of overrun.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 677fe55 (serial: imx: Fix recursive locking bug) introduces an
uninitialized variable warning as below.
CC drivers/tty/serial/imx.o
drivers/tty/serial/imx.c: In function ‘imx_console_write’:
include/linux/spinlock.h:340:2: warning: ‘flags’ may be used uninitialized in this function [-Wuninitialized]
drivers/tty/serial/imx.c:1214:16: note: ‘flags’ was declared here
Initialize the variable to suppress the warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe
on SMP) introduced a recursive locking bug in imx_console_write().
The callchain is:
imx_rxint()
spin_lock_irqsave(&sport->port.lock,flags);
...
uart_handle_sysrq_char();
sysrq_function();
printk();
imx_console_write();
spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD
The bad news is that the kernel debugging facilities can dectect the
problem, but the printks never surface on the serial console for
obvious reasons.
There is a similar issue with oops_in_progress. If the kernel crashes
we really don't want to be stuck on the lock and unable to tell what
happened.
In general most UP originated drivers miss these checks and nobody
ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by
a large number of developers.
The solution is to avoid locking in the sysrq case and trylock in the
oops_in_progress case.
This scheme is used in other drivers as well and it would be nice if
we could move this to a common place, so the usual copy/paste/modify
bugs can be avoided.
Now there is another issue with this scheme:
CPU0 CPU1
printk()
rxint()
sysrq_detection() -> sets port->sysrq
return from interrupt
console_write()
if (port->sysrq)
avoid locking
port->sysrq is reset with the next receive character. So as long as
the port->sysrq is not reset and this can take an endless amount of
time if after the break no futher receive character follows, all
console writes happen unlocked.
While the current writer is protected against other console writers by
the console sem, it's unprotected against open/close or other
operations which fiddle with the port. That's what the above mentioned
commit tried to solve.
That's an issue in all drivers which use that scheme and unfortunately
there is no easy workaround. The only solution is to have a separate
indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to
smp_processor_id() before calling into handle_sysrq() and resets it to
-1 after that. Then change the locking check to:
if (port->sysrq_cpu == smp_processor_id())
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(port->lock, flags);
else
spin_lock_irqsave(port->lock, flags);
That would force all other cpus into the spin_lock path. Problem
solved, but that's way beyond the scope of this fix and really wants
to be implemented in a common function which calls the uart specific
write function to avoid another gazillion of hard to debug
copy/paste/modify bugs.
Reported-and-tested-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cdc8da3998.
In my attempt to fix a build warning on arm randconfig a build error on
imx_v6_v7_defconfig was introduced, so revert it for now.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_CONSOLE_POLL is not defined, the following build warning happens:
drivers/tty/serial/imx.c:274:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:283:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
Move imx_port_ucrs_saver/restore under CONFIG_CONSOLE_POLL ifdef block to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silences the following checkpatch error:
ERROR: that open brace { should be on the previous line
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
platform_get_drvdata always retrun a valid value after probe succeed.
It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
These error paths are used more often now after deep changes to the
clock code and pinctrl is still new for imx. So help debugging and give
clues in the boot log.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the part of the effort to enable SPARE_IRQ for imx platform,
the macro MXC_INTERNAL_IRQS will be removed. The imx serial driver
has a references to it for a decision on flags of request_irq call
based on rtsirq is beyond MXC_INTERNAL_IRQS. However the searching
on imx platform code tells that rtsirq will never be beyond
MXC_INTERNAL_IRQS. That said, the check, consequently the reference
to MXC_INTERNAL_IRQS are not needed, so remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
