Adding IRQ defintions for DaVinci DM355 and default interrupt
priorities for DM355
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Clear any set bits in the 'NEXT' field of the MDCTL register in the
Power and Sleep Controller (PSC) before setting any new bits.
This also allows some minor cleanup by removing some no longer
needed lines of code.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:
- Only handle the number of GPIOs the chip actually has. So
for example on dm6467, GPIO-42 is the last GPIO, and trying
to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.
- Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
previously, only the first five were enabled, so GPIO-80
and above (on dm355) wouldn't trigger IRQs.
- Use the right IRQ for each GPIO bank. The wrong values were
used for dm355 chips, so GPIO IRQs got routed incorrectly.
- Handle up to four pairs of 16-bit GPIO banks ... previously
only three were handled, so accessing GPIO-96 and up (e.g. on
dm355) would oops.
- Update several comments that were dm6446-specific.
Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.
One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs. Some
bitmap logic could fix that if needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Original code for 2.6.10 and 2.6.28 series done by Texas Instruments
and MontaVista, but major updates and rework done by Troy Kisky and
David Brownell.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use clock framework instead of hard-coded CLOCK_TICK_RATE for
determining timer tick frequencies.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping. From now on, drivers should always use
ioremap() instead of IO_ADDRESS().
In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is a significant rework of the low-level clock, PLL and Power
Sleep Controller (PSC) implementation for the DaVinci family. The
primary goal is to have better modeling if the hardware clocks and
features with the aim of DVFS functionality.
Highlights:
- model PLLs and all PLL-derived clocks
- model parent/child relationships of PLLs and clocks
- convert to new clkdev layer
- view clock frequency and refcount via /proc/davinci_clocks
Special thanks to significant contributions and testing by David
Brownell.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In non-SMP mode, the variable section attribute specified by DECLARE_PER_CPU()
does not agree with that specified by DEFINE_PER_CPU(). This means that
architectures that have a small data section references relative to a base
register may throw up linkage errors due to too great a displacement between
where the base register points and the per-CPU variable.
On FRV, the .h declaration says that the variable is in the .sdata section, but
the .c definition says it's actually in the .data section. The linker throws
up the following errors:
kernel/built-in.o: In function `release_task':
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
To fix this, DECLARE_PER_CPU() should simply apply the same section attribute
as does DEFINE_PER_CPU(). However, this is made slightly more complex by
virtue of the fact that there are several variants on DEFINE, so these need to
be matched by variants on DECLARE.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Got this warning from Kconfig:
boolean symbol INPUT tested for 'm'? test forced to 'n'
because INPUT is tristate, not bool.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert PCI root bus resources for the FRV-based MB93090 development kit
motherboard. This is required because the CPU's window onto the PCI bus
address space is considerably smaller than the CPU's full address space
and non-PCI devices lie outside of the PCI window that we might want to
access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
reiserfs: fix j_last_flush_trans_id type
fs: Mark get_filesystem_list() as __init function.
kill vfs_stat_fd / vfs_lstat_fd
Separate out common fstatat code into vfs_fstatat
ecryptfs: use memdup_user()
ncpfs: use memdup_user()
xfs: use memdup_user()
sysfs: use memdup_user()
btrfs: use memdup_user()
xattr: use memdup_user()
autofs4: use memchr() in invalid_string()
Documentation/filesystems: remove out of date reference to BKL being held
Fix i_mutex vs. readdir handling in nfsd
fs/compat_ioctl: fix build when !BLOCK
Fix autofs_expire()
No need for crossing to mountpoint in audit_tag_tree()
Safer nfsd_cross_mnt()
Touch all affected namespaces on propagation of mount
Fix AUTOFS_DEV_IOCTL_REQUESTER_CMD
This is a version incorporating Christoph's suggestion.
Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
mmap2 uses a fixed page shift of 12, regardless of the PAGE_SIZE setting.
Fix up the mmap2 code to add some sanity checks on the mapping, and to
update pgoff accordingly.
Error handling bits based on 4280e3126f
("frv: fix mmap2 error handling").
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix allmodconfig compilation breakage.
[IA64] smp_flush_tlb_mm() should only send IPI's to cpus in cpu_vm_mask
[IA64] export smp_send_reschedule
This patch fixes the following compilation error caused by recursive
inclusion of kernel.h which defines BUILD_BUG_ON().
In this case, the case it catches will be caught by the case
CONFIG_PARAVIRT=n, so removing it would not hurt compile time check
very much. So fix the breakage by removing it.
CC arch/ia64/kernel/asm-offsets.s
In file included from include/linux/bitops.h:17,
from include/linux/kernel.h:15,
from include/linux/sched.h:52,
from arch/ia64/kernel/asm-offsets.c:9:
arch/ia64/include/asm/bitops.h: In function 'set_bit':
arch/ia64/include/asm/bitops.h:47: error: implicit declaration of function 'BUILD_BUG_ON'
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Stop the FRV arch from attempting to #include <linux/blk.h> as it doesn't
exist.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
* master.kernel.org:/home/rmk/linux-2.6-arm: (48 commits)
[ARM] S3C24XX: ADC: Check pending queue before freeing adc client
[ARM] S3C: Fix ADC driver sparse warning
[ARM] Osiris: Fix double initialisation in machine block
[ARM] Anubis: Fix sparse warnings for items that should be static
[ARM] JIVE: Fix sparse warnings about items which should be static
[ARM] S3C: Fix sparse warning from missing 's3c_device_hwmon'
[ARM] S3C24XX: Fix sparse error in gpiolib.c
[ARM] 5455/1: Fix IRQ noise from VIC code
[ARM] 5454/1: ep93xx_eth: fix sparse warnings
[ARM] remove .gitignore from include/asm-arm
Update MAINTAINERS
mxc defconfig updates
mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
mx31ads: Depend on all the WM8350 core dependencies for WM1133-EV1 board
Fix ifdef in plat-mxc/irc.c
MX1ADS: remove I2C ifdefs
qong: remove AIPS[12] mappings from machine-specific iotable
mx31ads: imoux pins should be passed in as unsigned int
MXC: remove orphan imx_init_uart() definition
mx31: pin definition for csi
...
This renames include/asm-h8300/timer.h into arch/h8300/include/asm: it
was left over just because that file had been created in the -mm tree
before the whole h8300 header subdirectory had been moved, and then got
merged in the old location afterwards.
(See commits e0b0f9e4ea: "h8300: update
timer handler - new files" and 758db3f211:
"[h8300] move include/asm-h8300 to arch/h8300/include/asm" for details).
This also removes a left-over .gitignore file in include/asm-arm that
became stale when the ARM header files were moved (which happened in
multiple commits, just see "git log -- include/asm-arm" for details).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: move include/asm-m32r/* to arch/m32r/include/asm/
m32r: move include/asm-m32r headers to arch/m32r/include/asm
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix microcode driver newly spewing warnings
x86, PAT: Remove page granularity tracking for vm_insert_pfn maps
x86: disable X86_PTRACE_BTS for now
x86, documentation: kernel-parameters replace X86-32,X86-64 with X86
x86: pci-swiotlb.c swiotlb_dma_ops should be static
x86, PAT: Remove duplicate memtype reserve in devmem mmap
x86, PAT: Consolidate code in pat_x_mtrr_type() and reserve_memtype()
x86, PAT: Changing memtype to WC ensuring no WB alias
x86, PAT: Handle faults cleanly in set_memory_ APIs
x86, PAT: Change order of cpa and free in set_memory_wb
x86, CPA: Change idmap attribute before ioremap attribute setup
Check pending queue and remove the adc client being released.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.
This fixes the following sparse warning:
adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The .init_machine entry in mach-osiris.c had the same entry
twice, so remove one definition to fix the following warning
from sparse:
mach-osiris.c:416:3: warning: Initializer entry defined twice
mach-osiris.c:418:3: also defined here
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'anubis_ide_platdata' statis as it is not used outside
the file it is in, fixing the following sparse warning:
mach-anubis.c:246:27: warning: symbol 'anubis_ide_platdata' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warning due to s3c_device_hwmon being
missing from <plat/devs.h>
devs.c:380:24: warning: symbol 's3c_device_hwmon' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>
gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'x86/uv' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: UV BAU distribution and payload MMRs
x86: UV: BAU partition-relative distribution map
x86, uv: add Kconfig dependency on NUMA for UV systems
x86: prevent /sys/firmware/sgi_uv from being created on non-uv systems
x86, UV: Fix for nodes with memory and no cpus
x86, UV: system table in bios accessed after unmap
x86: UV BAU messaging timeouts
x86: UV BAU and nodes with no memory
Jeff Garzik reported this WARN_ON() noise:
> Kernel: 2.6.30-rc1-00306-g8371f87
> Hardware: ICH10 x86-64
>
> This is a regression from 2.6.29. Microcode spews the following WARNING
> multiple times during boot:
>
> ------------[ cut here ]------------
> WARNING: at fs/sysfs/group.c:138 sysfs_remove_group+0xeb/0xf0()
> Hardware name: sysfs group ffffffffa0209700 not found for
> kobject 'cpu0'
Keep sysfs files around for cpus even when we failed to locate
microcode for them at the moment of module loading. The appropriate
microcode firmware can become available later on.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This change resolves the problem of too many single page entries
in pat_memtype_list and "freeing invalid memtype" errors with i915,
reported here:
http://marc.info/?l=linux-kernel&m=123845244713183&w=2
Remove page level granularity track and untrack of vm_insert_pfn.
memtype tracking at page granularity does not scale and cleaner
approach would be for the driver to request a type for a bigger
IO address range or PCI io memory range for that device, either at
mmap time or driver init time and just use that type during
vm_insert_pfn.
This patch just removes the track/untrack of vm_insert_pfn. That
means we will be in same state as 2.6.28, with respect to these APIs.
Newer APIs for the drivers to request a memtype for a bigger region
is coming soon.
[ Impact: fix Xorg startup warnings and hangs ]
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <20090408223716.GC3493@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The VIC code will attempt to perform som
default set_irq_chip() and set_irq_chip_data()
on all IRQs supported by the VIC, while the new
IRQ handling code strictly checks for the global
NR_IRQS to be respected also for these IRQs.
This patch will respect the interrupt mask passed
to the VIC driver and will prevent it from
attempting to call these functions on any unused
interrupts.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having flush_tlb_mm->smp_flush_tlb_mm() send an IPI to every cpu
on the system is occasionally triggering spin_lock contention in
generic_smp_call_function_interrupt().
Follow x86 arch's lead and only sends IPIs to the cpus in mm->cpu_vm_mask.
Experiments with this change have shown significant improvement in this
contention issue.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
KVM will use smp_send_reschedule to force a cpu out of guest mode.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch correctly sets BAU memory mapped registers to point
to the sending activation descriptor table and target payload table.
The "Broadcast Assist Unit" is used for TLB shootdown in UV.
The memory mapped registers that point to sending and receiving
memory structures contain node numbers.
In one case the __pa() function did not provide the node id of
memory on blade zero in configurations where that id is nonzero.
In another case, it was assumed that memory was allocated on
the local node. That assumption is not true in a configuration
in which the node has no memory.
Tested on the UV hardware simulator.
[ Impact: fix possible runtime crash due to incorrect TLB logic ]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1LuR5Z-0007An-B8@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: remove some pointless conditionals before kfree()
sbus: changed ioctls to unlocked
sparc: asm/atomic.h on 32bit should include asm/system.h for xchg
sparc64: Fix smp_callin() locking.
This patch removes several i.MX board specific defconfig files in favour
for a mx1_defconfig, mx27_defconfig and mx3_defconfig. All config files
have all currently available boards, i.MX specific drivers and the network
device drivers for the boards enabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
