The GPIO was incorrectly named. As it has no user in the whole kernel
tree, just rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Modify the sh7757_dmae1_slave to add paramters of RSPI's slave_id.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This has turned in to quite a mess, and with CPUs that care using
dmaengine now it's about time to start cleaning up after the legacy DMA
code. For starters, kill off the stubs for the CPUs that don't do
anything, as well as all of the unused definitions. This leaves us with a
set of IRQs and base addresses we can deal with later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
cpu-sh4a headers take priority over cpu-sh4 ones by virtue of the build
system, there's no need to try and mingle sh4a stuff in cpu-sh4.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7734.
This adds support SCIF, TMU and RTC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR of SH7763, SH7764, SH7780 and SH7785 is constitution same as SH7757.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR of SH7723 and SH7730 is constitution same as SH7724.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current div6 clocks can specify their current parent clocks
from its register value if it is registered
by sh_clk_div6_reparent_register().
This patch modifies all div6 clocks into SH_CLK_DIV6_EXT().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unused indices produce empty entries in the clock array, which then lead to
Oopses at boot-time.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current sh clocks are using pm_runtime frame work instead of old hwblk.
So, HWBLK_UNKNOWN, HWBLK_DBG and HWBLK_SUBC are not needed for now.
Now mstp32 clocks are registered by sh_clk_mstp32_register(),
but the clock which isn't defined by SH_CLK_MSTP32() macro
will be crash. because it doesn't have enable_reg.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current sh clocks are using pm_runtime frame work instead of old hwblk.
So, HWBLK_UNKNOWN and HWBLK_DBG are not needed for now.
Now mstp32 clocks are registered by sh_clk_mstp32_register(),
but the clock which isn't defined by SH_CLK_MSTP32() macro
will be crash. because it doesn't have enable_reg.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current clk_ops doesn't support .init which
is used to select external clock on ecovec
without CONFIG_SH_CLK_CPG_LEGACY.
To solve this problem, this patch add div6_reparent_clks
to clock-sh7724.
This patch solve compile error too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in support for GPIO/pinmux on the SH-X3 proto CPUs. This will
subsequently be used by the x3proto board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the MMCIF romImage boot support
for sh7724 and the Ecovec board. With this patch
applied and CONFIG_ROMIMAGE_MMCIF selected the
romImage kernel image can be written to a MMC card
and booted directly by the sh7724 cpu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that DMA slave IDs are only used used in platform specific code and have
become opaque cookies for the rest of the code, we can make the, CPU specific
too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR_TS_HIGH_SHIFT is defined as a shift of TS high bits in CHCR register,
relative to low bits. The TS_INDEX2VAL() macro has to take this into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently address translation is default-enabled regardless of whether
CONFIG_MMU is set or not in the SH-4 case, this fixes it up, and also
makes the control init word a bit more readable in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the status of the utlb and itlb entries through debugfs.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the TLB wiring code depends on MMUCR.URB for working out where
to place the wired entry, but fails to take the replacment counter in to
consideration. This fixes up the wiring logic and ensures that wired
entries remain so.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_tlb_page() can be used to flush TLB entries that map executable
pages. Therefore, we need to ensure that the ITLB is also flushed in
local_flush_tlb_page().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
DMA CHCR register layout is equal on sh7722 and sh7724, reuse definitions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the store queue API and the PMB remapping take unsigned long for
their pgprot flags, which cuts off the extended protection bits. In the
case of the PMB this isn't really a problem since the cache attribute
bits that we care about are all in the lower 32-bits, but we do it just
to be safe. The store queue remapping on the other hand depends on the
extended prot bits for enabling userspace access to the mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tested to work with a SIU ASoC driver on sh7722 (migor).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the original arch/sh/drivers/dma/dma-sh.c and the new SH dmaengine drivers
do not take into account bits 3:2 of the Transfer Size field in the CHCR
register, besides, bit-field defines set bit 2, but the mask only passes bits
1:0 through. TS_16BLK and TS_32BLK macros are bogus too. This patch fixes all
these issues for sh7722 and sh7724, other CPUs stay unchanged and might need to
be fixed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements dynamic probing for the system FPGA. The system reset
controller contains a fixed magic read word in order to identify the
FPGA. This just utilizes a simple loop that scans across all of the fixed
physical areas (area 0 through area 6) to locate the FPGA.
The FPGA also contains register information detailing the area mappings
and chip select settings for all of the other blocks, so this needs to be
done before we can set up anything else.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Provide a new extended page flag, _PAGE_WIRED and an SH4 implementation
for wiring TLB entries and use it in the fixmap code path so that we can
wire the fixmap TLB entry.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
This paves the way for allowing individual CPUs to overload the
individual flushing routines that they care about without having to
depend on weak aliases. SH-4 is converted over initially, as it wires
up pretty much everything. The majority of the other CPUs will simply use
the default no-op implementation with their own region flushers wired up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We use flush_cache_page() outright in copy_to_user_page(), and nothing
else needs it, so just kill it off. SH-5 still defines its own version,
but that too will go away in the same fashion once it converts over.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the flush_dcache_mmap_lock()/flush_dcache_mmap_unlock()
definitions are identical across all CPUs, so just provide them
generically in asm/cacheflush.h.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_dcache_all() is used internally by the SH-4 cache code, it is not
part of the exported cache API, so make it static and don't export it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a central point for CPU cache initialization routines.
This replaces the antiquated p3_cache_init() method, which the vast
majority of CPUs never cared about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of reorganizing for allowing nommu to use the new
and generic cache.c, no functional changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
