The wiphy information is getting very close to being too
much for a typical netlink dump message and adding the
radar attributes to channels and interface combinations
can push it over the limit, which means userspace gets no
information whatsoever. Therefore, remove these again for
now, no driver actually supports radar detection anyway
and a modified userspace is required as well.
We're working on a solution that will allow userspace to
request splitting the information across multiple netlink
messages, which will allow us to add this back.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_beacon_add_tim() function might be called
by drivers with BHs enabled, which causes a potential
deadlock if TX happens at the same time and attempts to
lock the tim_lock as well. Use spin_lock_bh to fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This just converts a manually-implemented loop into a do..while loop
in con_work(). It also moves handling of EAGAIN inside the blocks
where it's already been determined an error code was returned.
Also update a few dout() calls near the affected code for
consistency.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This just rearranges the logic in con_work() a little bit so that a
flag is used to indicate a fault has occurred. This allows both the
fault and non-fault case to be handled the same way and avoids a
couple of nearly consecutive gotos.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An error occurring on a ceph connection is treated as a fault,
causing the connection to be reset. The initial part of this fault
handling has to be done while holding the connection mutex, but
it must then be dropped for the last part.
Separate the part of this fault handling that executes without the
lock into its own function, con_fault_finish(). Move the call to
this new function, as well as call that drops the connection mutex,
into ceph_fault(). Rename that function con_fault() to reflect that
it's only handling the connection part of the fault handling.
The motivation for this was a warning from sparse about the locking
being done here. Rearranging things this way keeps all the mutex
manipulation within ceph_fault(), and this stops sparse from
complaining.
This partially resolves:
http://tracker.ceph.com/issues/4184
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Collect the code that tests for and implements a backoff delay for a
ceph connection into a new function, ceph_backoff().
Make the debug output messages in that part of the code report
things consistently by reporting a message in the socket closed
case, and by making the one for PREOPEN state report the connection
pointer like the rest.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Eliminate most of the problems in the libceph code that cause sparse
to issue warnings.
- Convert functions that are never referenced externally to have
static scope.
- Pass NULL rather than 0 for a pointer argument in one spot in
ceph_monc_delete_snapid()
This partially resolves:
http://tracker.ceph.com/issues/4184
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define and use functions that encapsulate operations performed on
a connection's flags.
This resolves:
http://tracker.ceph.com/issues/4234
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
commit "ip_gre: allow CSUM capable devices to handle packets"
aa0e51cdda, broke GRE_CSUM case.
GRE_CSUM needs checksum computed for inner packet. Therefore
csum-calculation can not be offloaded if tunnel device requires
GRE_CSUM. Following patch fixes it by computing inner packet checksum
for GRE_CSUM type, for all other type of GRE devices csum is offloaded.
CC: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE-GSO generates ip fragments with id 0,2,3,4... for every
GSO packet, which is not correct. Following patch fixes it
by setting ip-header id unique id of fragments are allowed.
As Eric Dumazet suggested it is optimized by using inner ip-header
whenever inner packet is ipv4.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This member of struct virtio_chan is calculated from nr_free_buffer_pages
so change its type to unsigned long in case of overflow.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deadlock might be caused by allocating memory with GFP_KERNEL in
runtime_resume and runtime_suspend callback of network devices in iSCSI
situation, so mark network devices and its ancestor as 'memalloc_noio'
with the introduced pm_runtime_set_memalloc_noio().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sock_diag_lock_handler() and sock_diag_unlock_handler() actually
make the code less readable. Get rid of them and make the lock usage
and access to sock_diag_handlers[] clear on the first sight.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userland can send a netlink message requesting SOCK_DIAG_BY_FAMILY
with a family greater or equal then AF_MAX -- the array size of
sock_diag_handlers[]. The current code does not test for this
condition therefore is vulnerable to an out-of-bound access opening
doors for a privilege escalation.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating a file structure in function get_empty_filp() might fail because
of several reasons:
- not enough memory for file structures
- operation is not allowed
- user is over its limit
Currently the function returns NULL in all cases and we loose the exact
reason of the error. All callers of get_empty_filp() assume that the function
can fail with ENFILE only.
Return error through pointer. Change all callers to preserve this error code.
[AV: cleaned up a bit, carved the get_empty_filp() part out into a separate commit
(things remaining here deal with alloc_file()), removed pipe(2) behaviour change]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If the socket is full, we're better off just waiting until it empties,
or until the connection is broken. The reason why we generally don't
want to time out is that the call to xprt->ops->release_xprt() will
trigger a connection reset, which isn't helpful...
Let's make an exception for soft RPC calls, since they have to provide
timeout guarantees.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
In fast open the sender unncessarily reduces the space available
for data in SYN by 12 bytes. This is because in the sender
incorrectly reserves space for TS option twice in tcp_send_syn_data():
tcp_mtu_to_mss() already accounts for TS option space. But it further
reserves MAX_TCP_OPTION_SPACE when computing the payload space.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mem cgroup socket limit is only used if the config option is
enabled. Found with sparse
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch found a locking bug in netif_set_xps_queue in which we were not
releasing the lock in the case of an allocation failure.
This change corrects that so that we release the xps_map_mutex before
returning -ENOMEM in the case of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we handle icmp errors in each transport protocol's err_handler,
for icmp protocols, that is ping_err. Since this handler only care
of those icmp errors triggered by echo request, errors triggered
by echo reply(which sent by kernel) are sliently ignored.
So wrap ping_err() with icmp_err() to deal with those icmp errors.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Merge misc patches from Andrew Morton:
- Florian has vanished so I appear to have become fbdev maintainer
again :(
- Joel and Mark are distracted to welcome to the new OCFS2 maintainer
- The backlight queue
- Small core kernel changes
- lib/ updates
- The rtc queue
- Various random bits
* akpm: (164 commits)
rtc: rtc-davinci: use devm_*() functions
rtc: rtc-max8997: use devm_request_threaded_irq()
rtc: rtc-max8907: use devm_request_threaded_irq()
rtc: rtc-da9052: use devm_request_threaded_irq()
rtc: rtc-wm831x: use devm_request_threaded_irq()
rtc: rtc-tps80031: use devm_request_threaded_irq()
rtc: rtc-lp8788: use devm_request_threaded_irq()
rtc: rtc-coh901331: use devm_clk_get()
rtc: rtc-vt8500: use devm_*() functions
rtc: rtc-tps6586x: use devm_request_threaded_irq()
rtc: rtc-imxdi: use devm_clk_get()
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
rtc: rtc-pcf8583: use dev_warn() instead of printk()
rtc: rtc-sun4v: use pr_warn() instead of printk()
rtc: rtc-vr41xx: use dev_info() instead of printk()
rtc: rtc-rs5c313: use pr_err() instead of printk()
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
rtc: rtc-ds2404: use dev_err() instead of printk()
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
...
After I came across a help text for SUNGEM mentioning a broken sun.com
URL, I felt like fixing those up, as they are now pointing to oracle.com
URLs.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like its possible to open thousands of TCP IPv6
sessions on a server, all landing in a single slot of TCP hash
table. Incoming packets have to lookup sockets in a very
long list.
We should hash all bits from foreign IPv6 addresses, using
a salt and hash mix, not a simple XOR.
inet6_ehashfn() can also separately use the ports, instead
of xoring them.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
We should get 'type' and 'code' from the outer ICMP header.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
This patch enhances the IB core support for Memory Windows (MWs).
MWs allow an application to have better/flexible control over remote
access to memory.
Two types of MWs are supported, with the second type having two flavors:
Type 1 - associated with PD only
Type 2A - associated with QPN only
Type 2B - associated with PD and QPN
Applications can allocate a MW once, and then repeatedly bind the MW
to different ranges in MRs that are associated to the same PD. Type 1
windows are bound through a verb, while type 2 windows are bound by
posting a work request.
The 32-bit memory key is composed of a 24-bit index and an 8-bit
key. The key is changed with each bind, thus allowing more control
over the peer's use of the memory key.
The changes introduced are the following:
* add memory window type enum and a corresponding parameter to ib_alloc_mw.
* type 2 memory window bind work request support.
* create a struct that contains the common part of the bind verb struct
ibv_mw_bind and the bind work request into a single struct.
* add the ib_inc_rkey helper function to advance the tag part of an rkey.
Consumer interface details:
* new device capability flags IB_DEVICE_MEM_WINDOW_TYPE_2A and
IB_DEVICE_MEM_WINDOW_TYPE_2B are added to indicate device support
for these features.
Devices can set either IB_DEVICE_MEM_WINDOW_TYPE_2A or
IB_DEVICE_MEM_WINDOW_TYPE_2B if it supports type 2A or type 2B
memory windows. It can set neither to indicate it doesn't support
type 2 windows at all.
* modify existing provides and consumers code to the new param of
ib_alloc_mw and the ib_mw_bind_info structure
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Fix an Oops in the pNFS layoutget code
- Fix a number of NFSv4 and v4.1 state recovery deadlocks and hangs
due to the interaction of the session drain lock and state management
locks.
- Remove task->tk_xprt, which was hiding a lot of RCU dereferencing bugs
- Fix a long standing NFSv3 posix lock recovery bug.
- Revert commit 324d003b0c. It turned out
that the root cause of the deadlock was due to interactions with the
workqueues that have now been resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRJUfVAAoJEGcL54qWCgDySIoP/2QC2qNKqfcoIwOqOAR0pu5m
wHybR67WXt/R6EK17l273apHfnJQb/IFFKRBfAIAW0vy4bJLwHMtutIeUweFWht2
hmluYqVWAa9lPwaY1YMolo8Mfizaj0cY3QHv2ogF4poY0SLO6L8O/xo8n8nrn/pk
QJW9tcvz43A2tbW92t833sQMFQSSjs9L2tvxM/BEahLrSEE4dl6WMWscmHQ/IXt/
Hs3ADc4//dDF36k5lu7tU0qaVNDacjMXCV6Bw0HUCWCwjWzqmPxSlTDKAcer2vpm
UawKDFTF4X1QYwbtGlNju0xhsSGRg7ZNRVEeRxqSROT280nzpp7C3CjM9sECtM2l
SR9RqoYfBsEAyWZtsALApuSBZZZHOvUfVJEL1Cm0ZSeEbWSOO/DT07KRVgfb97h4
hmE7pn5htgXdiGN2YCphMjrqjaoP4aKmULenj1h1jHbDOgrlqp2QLWqg/5NxMsTw
M3vmYqQWkW60JN6e1pWJbsoyUkSMTVycRNrZ6WgShtd1lrz3tg66rDXYWdIhU6pT
6qAKrkXnM5JkLoMoImNQod00Vr1ZXpVc8DLoFtug8rGohCdFJhWkYHefqVJ9rFhv
2S2NpKDsFiA0q3aK0/YAkUnykYDAnLn7BM5SvhJjq8mKru4bP70PrN9LO8aqhE4E
fFgj2MGG5QwrL0/GMuls
=dthb
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix an Oops in the pNFS layoutget code
- Fix a number of NFSv4 and v4.1 state recovery deadlocks and hangs due
to the interaction of the session drain lock and state management
locks.
- Remove task->tk_xprt, which was hiding a lot of RCU dereferencing
bugs
- Fix a long standing NFSv3 posix lock recovery bug.
- Revert commit 324d003b0c ("NFS: add nfs_sb_deactive_async to avoid
deadlock"). It turned out that the root cause of the deadlock was
due to interactions with the workqueues that have now been resolved.
* tag 'nfs-for-3.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (22 commits)
NLM: Ensure that we resend all pending blocking locks after a reclaim
umount oops when remove blocklayoutdriver first
sunrpc: silence build warning in gss_fill_context
nfs: remove kfree() redundant null checks
NFSv4.1: Don't decode skipped layoutgets
NFSv4.1: Fix bulk recall and destroy of layouts
NFSv4.1: Fix an ABBA locking issue with session and state serialisation
NFSv4: Fix a reboot recovery race when opening a file
NFSv4: Ensure delegation recall and byte range lock removal don't conflict
NFSv4: Fix up the return values of nfs4_open_delegation_recall
NFSv4.1: Don't lose locks when a server reboots during delegation return
NFSv4.1: Prevent deadlocks between state recovery and file locking
NFSv4: Allow the state manager to mark an open_owner as being recovered
SUNRPC: Add missing static declaration to _gss_mech_get_by_name
Revert "NFS: add nfs_sb_deactive_async to avoid deadlock"
SUNRPC: Nuke the tk_xprt macro
SUNRPC: Avoid RCU dereferences in the transport bind and connect code
SUNRPC: Fix an RCU dereference in xprt_reserve
SUNRPC: Pass pointers to struct rpc_xprt to the congestion window
SUNRPC: Fix an RCU dereference in xs_local_rpcbind
...
When an entry flagged with "nomatch" was tested by ipset, it
returned the error message "Kernel error received:
Directory not empty" instead of "<element> is NOT in set <setname>"
(reported by John Brendler).
The internal error code was not properly transformed before returning
to userspace, fixed.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
Eric Dumazet wrote:
| Some strange crashes happen in rt6_check_expired(), with access
| to random addresses.
|
| At first glance, it looks like the RTF_EXPIRES and
| stuff added in commit 1716a96101
| (ipv6: fix problem with expired dst cache)
| are racy : same dst could be manipulated at the same time
| on different cpus.
|
| At some point, our stack believes rt->dst.from contains a dst pointer,
| while its really a jiffie value (as rt->dst.expires shares the same area
| of memory)
|
| rt6_update_expires() should be fixed, or am I missing something ?
|
| CC Neil because of https://bugzilla.redhat.com/show_bug.cgi?id=892060
Because we do not have any locks for dst_entry, we cannot change
essential structure in the entry; e.g., we cannot change reference
to other entity.
To fix this issue, split 'from' and 'expires' field in dst_entry
out of union. Once it is 'from' is assigned in the constructor,
keep the reference until the very last stage of the life time of
the object.
Of course, it is unsafe to change 'from', so make rt6_set_from simple
just for fresh entries.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Neil Horman <nhorman@tuxdriver.com>
CC: Gao Feng <gaofeng@cn.fujitsu.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reported-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c9af6db4c1 (net: Fix possible wrong checksum generation)
has a suspicous piece:
- skb_shinfo(skb1)->gso_type = skb_shinfo(skb)->gso_type;
-
+ skb_shinfo(skb)->tx_flags = skb_shinfo(skb1)->tx_flags & SKBTX_SHARED_FRAG;
skb1 is the new skb, therefore should be on the left side of the assignment.
This patch fixes it.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull workqueue [delayed_]work_pending() cleanups from Tejun Heo:
"This is part of on-going cleanups to remove / minimize usages of
workqueue interfaces which are deprecated and/or misleading.
This round drops a number of usages of [delayed_]work_pending(), which
are dangerous as they lack any form of synchronization and thus often
lead to buggy / unnecessary code. There are a couple legitimate use
cases in kernel. Hopefully, they can be converted and
[delayed_]work_pending() can be removed completely. Even if not,
removing most of misuses should make it more difficult to find
examples of misuses and thus slow down growth of them.
These changes are independent from other workqueue changes."
* 'for-3.9-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
wimax/i2400m: fix i2400m->wake_tx_skb handling
kprobes: fix wait_for_kprobe_optimizer()
ipw2x00: simplify scan_event handling
video/exynos: don't use [delayed_]work_pending()
tty/max3100: don't use [delayed_]work_pending()
x86/mce: don't use [delayed_]work_pending()
rfkill: don't use [delayed_]work_pending()
wl1251: don't use [delayed_]work_pending()
thinkpad_acpi: don't use [delayed_]work_pending()
mwifiex: don't use [delayed_]work_pending()
sja1000: don't use [delayed_]work_pending()
John W. Linville says:
====================
One last batch of stragglers intended for 3.9...
For the iwlwifi pull, Johannes says:
"I hadn't expected to ask you to pull iwlwifi-next again, but I have a
number of fixes most of which I'd also send in after rc1, so here it is.
The first commit is a merge error between mac80211-next and
iwlwifi-next; in addition I have fixes for P2P scanning and MVM driver
MAC (virtual interface) management from Ilan, a CT-kill (critical
temperature) fix from Eytan, and myself fixed three different little but
annoying bugs in the MVM driver.
The only ones I might not send for -rc1 are Emmanuel's debug patch, but
OTOH it should help greatly if there are any issues, and my own time
event debugging patch that I used to find the race condition but we
decided to keep it for the future."
For the mac80211 pull, Johannes says:
"Like iwlwifi-next, this would almost be suitable for rc1.
I have a fix for station management on non-TDLS drivers, a CAB queue
crash fix for mesh, a fix for an annoying (but harmless) warning, a
tracing fix and a documentation fix. Other than that, only a few mesh
cleanups."
Along with that is a fix for memory corruption in rtlwifi, an
orinoco_usb fix to avoid allocating a DMA buffer on the stack, an a
hostap fix to return -ENOMEM instead of -1 after a memory allocation
failure. The remaining bits implement 802.11ac support for the mwifiex
driver -- I think that is still worth getting into 3.9.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 68c3316311 (v4 GRE: Add TCP segmentation offload for GRE)
introduced a bug in error path.
dst is attached to skb, so will be released when skb is freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values provided for ceph_copy_to_page_vector() and
ceph_copy_from_page_vector() serve no purpose, so get rid of them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The functions used for working with ceph page vectors are defined
with char pointers, but they're really intended to operate on
untyped data. Change the types of these function parameters
to (void *) to reflect this.
(Note that the functions now assume void pointer arithmetic works
like arithmetic on char pointers.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add support for CEPH_OSD_OP_STAT operations in the osd client
and in rbd.
This operation sends no data to the osd; everything required is
encoded in identity of the target object.
The result will be ENOENT if the object doesn't exist. If it does
exist and no other error occurs the server returns the size and last
modification time of the target object as output data (in little
endian format). The size is a 64 bit unsigned and the time is
ceph_timespec structure (two unsigned 32-bit integers, representing
a seconds and nanoseconds value).
This resolves:
http://tracker.ceph.com/issues/4007
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Simplify the way the data length recorded in a message header is
calculated in ceph_osdc_build_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When !CONFIG_PROC_FS dev_mcast_init() is not defined,
actually we can just merge dev_mcast_init() into
dev_proc_init().
Reported-by: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the vars ip_rt_gc_timeout is used only when
CONFIG_SYSCTL is selected.
move these vars into CONFIG_SYSCTL.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to net/core/net-sysfs.c, group procfs code to
a single unit.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device is not able to handle checksumming it will
be handled in dev_xmit
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contain updates for your net-next tree, they are:
* Fix (for just added) connlabel dependencies, from Florian Westphal.
* Add aliasing support for conntrack, thus users can either use -m state
or -m conntrack from iptables while using the same kernel module, from
Jozsef Kadlecsik.
* Some code refactoring for the CT target to merge common code in
revision 0 and 1, from myself.
* Add aliasing support for CT, based on patch from Jozsef Kadlecsik.
* Add one mutex per nfnetlink subsystem, from myself.
* Improved logging for packets that are dropped by helpers, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Connection tracking helpers have to drop packets under exceptional
situations. Currently, the user gets the following logging message
in case that happens:
nf_ct_%s: dropping packet ...
However, depending on the helper, there are different reasons why a
packet can be dropped.
This patch modifies the existing code to provide more specific
error message in the scope of each helper to help users to debug
the reason why the packet has been dropped, ie:
nf_ct_%s: dropping packet: reason ...
Thanks to Joe Perches for many formatting suggestions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net/ipv6/reassembly.c:82:72: warning: incorrect type in argument 3 (different base types)
net/ipv6/reassembly.c:82:72: expected unsigned int [unsigned] [usertype] c
net/ipv6/reassembly.c:82:72: got restricted __be32 [usertype] id
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This probably is the last big pull request for wireless bits
for 3.9. Of course, I'm sure there will be a few stragglers here
and there...surely a few bug fixes as well... :-) (In fact, I see
that Johannes has already queued-up a few more for me while I was
preparing this...)
Included are a number of pulls...
For mac80211-next, Johannes says:
"The biggest change I have is undoubtedly Marco's mesh powersave
implementation. Beyond that, I have a patch from Emmanuel to modify the
DTIM period API in mac80211, scan improvements and a removal of some
previous workaround code from Stanislaw, dynamic short slot time from
Thomas and 64-bit station byte counters from Vladimir. I also made a
number of changes myself, some related to WoWLAN, some auth/deauth
improvements and most of them BSS list cleanups."
"This time, I have relatively large number of fixes in various areas of
the code (a memory leak in regulatory, an RX race in mac80211, the new
radar checking caused a P2P device problem, some mesh issues with
stations, an older bug in tracing and for kernel-doc) as well as a
number of small new features. The biggest (in the diffstat) is my work
on hidden SSID tracking."
"Please pull to get
* radar detection work from Simon
* mesh improvements from Thomas
* a connection monitoring/powersave fix from Wojciech
* TDLS-related station management work from Jouni
* VLAN crypto fixes from Michael Braun
* CCK support in minstrel_ht from Felix
* an SMPS (not SMSP, oops) related improvement in mac80211 (Emmanuel)
* some WoWLAN work from Amitkumar Karwar: pattern match offset and a
documentation fix
* some WoWLAN work from myself (TCP connection wakeup feature API)
* and a lot of VHT (and some HT) work (also from myself)
And a number of more random cleanups/fixes. I merged mac80211/master to
avoid a merge problem there."
And regarding iwlwifi-next, Johannes says:
"We continue work on our new driver, but I also have a WoWLAN and AP mode
improvement for the previous driver and a change to use threaded
interrupts to prepare us for working with non-PCIe devices."
Regarding wl12xx, Luca says:
"A few more patches intended for 3.9. Mostly some clean-ups I've been
doing to make it easier to support device-tree. Also including one bug
fix for wl12xx where the rates we advertise were wrong and an update in
the wlconf structure to support newer firmwares."
For the nfc-next bits, Samuel says:
"This is the second NFC pull request for 3.9.
We have:
- A few pn533 fixes on top of Waldemar refactorization of the driver, one of
them fixes target mode.
- A new driver for Inside Secure microread chipset. It supports two
physical layers: i2c and MEI. The MEI one depends on a patchset that's
been sent to Greg Kroah-Hartman for inclusion into the 3.9 kernel [1]. The
dependency is a KConfig one which means this code is not buildable as long
as the MEI API is not usptream."
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
For the ath6kl bits, Kalle says:
"There's not anything special here, most of the patches are just code
cleanup. The only functional changes are using the beacon interval from user
space and fixing a crash which happens when inserting and removing the
module in a loop."
Also, I pulled the wireless tree in order to resolve some pending
merge issues. On top of that, there is a bunch of work on brcmfmac
that leads up to P2P support. Also, mwifiex, rtlwifi, and a variety
of other drivers see some basic cleanups and minor enhancements.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow our own family as the protocol value for socket creation.
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't really a need to have a separate file for it.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the default behavior for a looooooong time.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbor is cloned in xfrm6_fill_dst but seems to never be released.
Neighbor entry should be released when XFRM6 dst entry is destroyed
in xfrm6_dst_destroy, otherwise references may be kept forever on
the device pointed by the neighbor entry.
I may not have understood all the subtleties of XFRM & dst so I would
be happy to receive comments on this patch.
Signed-off-by: Romain Kuntz <r.kuntz@ipflavors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In osd_req_encode_op() there are a few cases that handle osd
opcodes that are never used in the kernel. The presence of
this code gives the impression it's correct (which really can't
be assumed), and may impose some unnecessary restrictions on
some upcoming refactoring of this code.
So delete this effectively dead code, and report uses of the
previously handled cases as unsupported.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If osd_req_encode_op() is given any opcode it doesn't recognize
it reports an error.
This patch fleshes out that routine to distinguish between
well-defined but unsupported values and values that are simply
bogus.
This and the next commit are related to:
http://tracker.ceph.com/issues/4126
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Update ceph_osd_op_name() to include the newly-added definitions in
"rados.h", and to match its counterpart in the user space code.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add the definition of ceph_osd_state_name(), to match its
counterpart in user space.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are no actual users of ceph_osdc_wait_event(). This would
have been one-shot events, but we no longer support those so just
get rid of this function.
Since this leaves nothing else that waits for the completion of an
event, we can get rid of the completion in a struct ceph_osd_event.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_create_event(), and it
provides 0 as its "one_shot" argument. Get rid of that argument and
just use 0 in its place.
Replace the code in handle_watch_notify() that executes if one_shot
is nonzero in the event with a BUG_ON() call.
While modifying "osd_client.c", give handle_watch_notify() static
scope.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is no caller of ceph_calc_raw_layout() outside of libceph, so
there's no need to export from the module.
Furthermore, there is only one caller, in calc_layout(), and it
is not much more than a simple wrapper for that function.
So get rid of ceph_calc_raw_layout() and embed it instead within
calc_layout().
While touching "osd_client.c", get rid of the unnecessary forward
declaration of __send_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only callers of ceph_osdc_init() and ceph_osdc_stop()
ceph_create_client() and ceph_destroy_client() (respectively)
and they are in the same kernel module as those two functions.
There's therefore no need to export those interfaces, so don't.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Two of the three callers of the osd client's send_queued() function
already hold the osd client mutex and drop it before the call.
Change send_queued() so it assumes the caller holds the mutex, and
update all callers accordingly. Rename it __send_queued() to match
the convention used elsewhere in the file with respect to the lock.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The "num_reply" parameter to ceph_osdc_new_request() is never
used inside that function, so get rid of it.
Note that ceph_sync_write() passes 2 for that argument, while all
other callers pass 1. It doesn't matter, but perhaps someone should
verify this doesn't indicate a problem.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes 0 as its "flags" argument. Get rid of that argument and
replace its use in ceph_osdc_writepages() with 0.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes 0 as its "dosync" argument. Get rid of that argument and
replace its use in ceph_osdc_writepages() with 0.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes the value true as its "nofail" argument. Get rid of that
argument and replace its use in ceph_osdc_writepages() with the
constant value true.
This and a number of cleanup patches that follow resolve:
http://tracker.ceph.com/issues/4126
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Should not use assignment in conditional:
warning: suggest parentheses around assignment used as truth value [-Wparentheses]
Problem introduced by:
commit 14bbd6a565
Author: Pravin B Shelar <pshelar@nicira.com>
Date: Thu Feb 14 09:44:49 2013 +0000
net: Add skb_unclone() helper function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They well deserve a separated unit.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry noticed (and bisected) that commit df881293c6
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.
Cc: Jouni Malinen <j@w1.fi>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use ipv6_addr_hash() and a single jhash invocation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker says:
====================
Two relatively small cleanup patches here, plus a reimplementation
of the patch Neil had questions about[1] in the last development
cycle.
Tested on today's net-next, between 32 and 64 bit x86 machines using
the server/client in tipc-utils, as usual.
[1] http://patchwork.ozlabs.org/patch/204507/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If mesh plink debugging is enabled, this gets annoying in
a crowded environment, fast.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mesh peering events into strings and make the
debug output a little easier to read. Also stop printing
the llid and plid since these don't change across peering
states and are random numbers anyway so they just amount
to noise.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_ht_cap_ie_to_sta_ht_cap() will clean up the
ht_supported flag and station bandwidth field for us
if the peer beacon doesn't have an HT capability element
(is operating as non-HT).
Also, we don't really need a special station ch_width
member to track the station operating mode any more so use
sta.bandwidth instead.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an interface is set down while authenticating or
associating, there's a station entry that will be
removed by the flushing in do_stop() and that will
cause a warning. It's otherwise harmless, but avoid
the warning by calling ieee80211_mgd_stop() first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 620038f6d2, gcc is throwing the following warning:
CC [M] net/sunrpc/auth_gss/auth_gss.o
In file included from include/linux/sunrpc/types.h:14:0,
from include/linux/sunrpc/sched.h:14,
from include/linux/sunrpc/clnt.h:18,
from net/sunrpc/auth_gss/auth_gss.c:45:
net/sunrpc/auth_gss/auth_gss.c: In function ‘gss_pipe_downcall’:
include/linux/sunrpc/debug.h:45:10: warning: ‘timeout’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_DEFAULT args); \
^
net/sunrpc/auth_gss/auth_gss.c:194:15: note: ‘timeout’ was declared here
unsigned int timeout;
^
If simple_get_bytes returns an error, then we'll end up calling printk
with an uninitialized timeout value. Reasonably harmless, but fairly
simple to fix by removing the printout of the uninitialised parameters.
Cc: Andy Adamson <andros@netapp.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
[Trond: just remove the parameters rather than initialising timeout]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Rewrite server shutdown to remove the assumption that there are no
longer any threads running (no longer true, for example, when shutting
down the service in one network namespace while it's still running in
others).
Do that by doing what we'd do in normal circumstances: just CLOSE each
socket, then enqueue it.
Since there may not be threads to handle the resulting queued xprts,
also run a simplified version of the svc_recv() loop run by a server to
clean up any closed xprts afterwards.
Cc: stable@kernel.org
Tested-by: Jason Tibbitts <tibbs@math.uh.edu>
Tested-by: Paweł Sikora <pawel.sikora@agmk.net>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
svc_age_temp_xprts expires xprts in a two-step process: first it takes
the sv_lock and moves the xprts to expire off their server-wide list
(sv_tempsocks or sv_permsocks) to a local list. Then it drops the
sv_lock and enqueues and puts each one.
I see no reason for this: svc_xprt_enqueue() will take sp_lock, but the
sv_lock and sp_lock are not otherwise nested anywhere (and documentation
at the top of this file claims it's correct to nest these with sp_lock
inside.)
Cc: stable@kernel.org
Tested-by: Jason Tibbitts <tibbs@math.uh.edu>
Tested-by: Paweł Sikora <pawel.sikora@agmk.net>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
As the number of iovecs in a send request is already limited within
UIO_MAXIOV(i.e. 1024) in __sys_sendmsg(), it's unnecessary to check it
again in TIPC stack.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change overload control to be purely byte-based, using
sk->sk_rmem_alloc as byte counter, and compare it to a calculated
upper limit for the socket receive queue.
For all connection messages, irrespective of message importance,
the overload limit is set to a constant value (i.e, 67MB). This
limit should normally never be reached because of the lower
limit used by the flow control algorithm, and is there only
as a last resort in case a faulty peer doesn't respect the send
window limit.
For datagram messages, message importance is taken into account
when calculating the overload limit. The calculation is based
on sk->sk_rcvbuf, and is hence configurable via the socket option
SO_RCVBUF.
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The tipc function discard_rx_queue() is just a duplicated
implementation of __skb_queue_purge(). Remove the former
and directly invoke __skb_queue_purge().
In doing so, the underscores convey to the code reader, more
information about the current locking state that is assumed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
After commit 3c294cb3 "tipc: remove the bearer congestion mechanism",
we try to grab the broadcast bearer lock when sending multicast
messages over the broadcast link. This will cause an oops because
the lock is never initialized. This is an old bug, but the lock
was never actually used before commit 3c294cb3, so that why it was
not visible until now. The oops will look something like:
BUG: spinlock bad magic on CPU#2, daemon/147
lock: bcast_bearer+0x48/0xffffffffffffd19a [tipc],
.magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 147, comm: daemon Not tainted 3.8.0-rc3+ #206
Call Trace:
spin_dump+0x8a/0x8f
spin_bug+0x21/0x26
do_raw_spin_lock+0x114/0x150
_raw_spin_lock_bh+0x19/0x20
tipc_bearer_blocked+0x1f/0x40 [tipc]
tipc_link_send_buf+0x82/0x280 [tipc]
? __alloc_skb+0x9f/0x2b0
tipc_bclink_send_msg+0x77/0xa0 [tipc]
tipc_multicast+0x11b/0x1b0 [tipc]
send_msg+0x225/0x530 [tipc]
sock_sendmsg+0xca/0xe0
The above can be triggered by running the multicast demo program.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need to use mac_len, lets cleanup things.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.
[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality. It only exports skb_mac_gso_segment()
function.
[ Use skb_reset_mac_len() -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mesh powersaving was added, pending bcast/mcast frames may go out the
CAB queue now. Unfortunately, the queue was only set up for AP mode, so we
would try to tx on the IEEE80211_INVAL_HW_QUEUE. Allow cab_queue for mesh
interfaces as well.
Fixes the following warning (or crash without MAC80211_VERBOSE_DEBUG):
WARNING: at net/mac80211/tx.c:1223 __ieee80211_tx+0x162/0x35f [mac80211]()
Modules linked in: mac80211_hwsim mac80211 cfg80211 [...]
Pid: 3085, comm: avahi-daemon Tainted: G W 3.8.0-rc1+ #377
Call Trace:
[<ffffffff81045c20>] warn_slowpath_common+0x83/0x9c
[<ffffffff81045c53>] warn_slowpath_null+0x1a/0x1c
[<ffffffffa083aef0>] __ieee80211_tx+0x162/0x35f [mac80211]
[<ffffffffa083cb1d>] ieee80211_tx+0xd3/0xf9 [mac80211]
[<ffffffffa083cc0f>] ieee80211_xmit+0xcc/0xd5 [mac80211]
[<ffffffffa083db59>] ieee80211_subif_start_xmit+0xc53/0xcd8 [mac80211]
[<ffffffff81319acd>] dev_hard_start_xmit+0x259/0x3ce
[<ffffffff81333d6b>] sch_direct_xmit+0x74/0x17d
[<ffffffff8131a0b1>] dev_queue_xmit+0x230/0x414
[<ffffffff8134877a>] ip_finish_output2+0x348/0x3aa
[<ffffffff81349029>] ip_finish_output+0x6c/0x71
[<ffffffff81349046>] NF_HOOK_COND.constprop.44+0x18/0x58
[<ffffffff8134a03a>] ip_mc_output+0x134/0x13c
[<ffffffff8134835a>] dst_output+0x18/0x1c
[<ffffffff81349a24>] ip_local_out+0x20/0x24
[<ffffffff8134a8cf>] ip_send_skb+0x16/0x3c
[<ffffffff8136bfba>] udp_send_skb+0x254/0x2b9
[<ffffffff8136c85e>] udp_sendmsg+0x5a8/0x7d4
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
