Print the most useful information during tx timeout to help debug.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DMA read watermark to 4 on 5703 in PCIX mode. This is needed to
prevent some tx timeouts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following problem:
http://bugzilla.kernel.org/show_bug.cgi?id=7969
The MSI state needs to be saved during suspend. PCI state saved
during tg3_init_one() does not contain valid MSI state because
MSI hasn't been enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During kernel bootup, a new T60 laptop (CoreDuo, 32-bit) hangs about
10%-20% of the time in acpi_init():
Calling initcall 0xc055ce1a: topology_init+0x0/0x2f()
Calling initcall 0xc055d75e: mtrr_init_finialize+0x0/0x2c()
Calling initcall 0xc05664f3: param_sysfs_init+0x0/0x175()
Calling initcall 0xc014cb65: pm_sysrq_init+0x0/0x17()
Calling initcall 0xc0569f99: init_bio+0x0/0xf4()
Calling initcall 0xc056b865: genhd_device_init+0x0/0x50()
Calling initcall 0xc056c4bd: fbmem_init+0x0/0x87()
Calling initcall 0xc056dd74: acpi_init+0x0/0x1ee()
It's a hard hang that not even an NMI could punch through! Frustratingly,
adding printks or function tracing to the ACPI code made the hangs go away
...
After some time an additional detail emerged: disabling the NMI watchdog
made these occasional hangs go away.
So i spent the better part of today trying to debug this and trying out
various theories when i finally found the likely reason for the hang: if
acpi_ns_initialize_devices() executes an _INI AML method and an NMI
happens to hit that AML execution in the wrong moment, the machine would
hang. (my theory is that this must be some sort of chipset setup method
doing stores to chipset mmio registers?)
Unfortunately given the characteristics of the hang it was sheer
impossible to figure out which of the numerous AML methods is impacted
by this problem.
As a workaround i wrote an interface to disable chipset-based NMIs while
executing _INI sections - and indeed this fixed the hang. I did a
boot-loop of 100 separate reboots and none hung - while without the patch
it would hang every 5-10 attempts. Out of caution i did not touch the
nmi_watchdog=2 case (it's not related to the chipset anyway and didnt
hang).
I implemented this for both x86_64 and i686, tested the i686 laptop both
with nmi_watchdog=1 [which triggered the hangs] and nmi_watchdog=2, and
tested an Athlon64 box with the 64-bit kernel as well. Everything builds
and works with the patch applied.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Convert the PDA code to use %fs rather than %gs as the segment for
per-processor data. This is because some processors show a small but
measurable performance gain for reloading a NULL segment selector (as %fs
generally is in user-space) versus a non-NULL one (as %gs generally is).
On modern processors the difference is very small, perhaps undetectable.
Some old AMD "K6 3D+" processors are noticably slower when %fs is used
rather than %gs; I have no idea why this might be, but I think they're
sufficiently rare that it doesn't matter much.
This patch also fixes the math emulator, which had not been adjusted to
match the changed struct pt_regs.
[frederik.deweerdt@gmail.com: fixit with gdb]
[mingo@elte.hu: Fix KVM too]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Ian Campbell <Ian.Campbell@XenSource.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Zachary Amsden <zach@vmware.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
/proc/pmu/info contains AC Power: 0 when booting without battery.
Force AC Power, it will be updated whenever the battery state changes.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move all the initialized variables to bss.
Mark a version string as const.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Speed up memory registration by filling in MTTs directly when the CPU
can write directly to the whole table (all mem-free cards, and to
Tavor mode on 64-bit systems with the patch I posted earlier). This
reduces the number of FW commands needed to register an MR by at least
a factor of 2 and speeds up memory registration significantly.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For Tavor, we currently reserve separate MPT and MTT space for FMRs to
avoid abusing the vmalloc space on 32 bit kernels. No such problem
exists on 64 bit kernels so let's not do it there.
This way we have a shared pool for MR and FMR resources, used on
demand. This will also make it possible to write MTTs for regular
regions directly from driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We allocate the MTT table with alloc_pages() and then do pci_map_sg(),
so we must call pci_dma_sync_sg() after the CPU writes to the MTT
table. This works since the device will never write MTTs on mem-free
HCAs, once we get rid of the use of the WRITE_MTT firmware command.
This change is needed to make that work, and is an improvement for
now, since it gives FMRs a chance at working.
For MPTs, both the device and CPU might write there, so we must
allocate DMA coherent memory for these.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MTTs are allocated in non-cache-coherent memory, so we must give
reserved MTTs their own cache line, to prevent both device and
CPU from writing into the same cache line at the same time.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reserved_mtts field has different meaning in Tavor and Arbel, so
we are wasting mtt entries on memfree. Fix the Arbel case to match
Tavor semantics.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA/iWARP driver for the Chelsio T3 1GbE and 10GbE adapters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Use timer macros to set function and data members and to modify
expiration time.
- Use DEFINE_TIMER for single (platform dependent) watchdog timers and
do not init them at run-time in these cases.
- del_timer_sync is common in most cases -- we want to wait for timer
function if it's still running.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Steve Hill <steve@navaho.co.uk>
Cc: Heiko Ronsdorf <hero@ihg.uni-duisburg.de>
Cc: Fernando Fuganti <fuganti@conectiva.com.br>
Cc: Gergely Madarasz <gorgo@itc.hu>
Cc: Ken Hollis <khollis@bitgate.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] remove __io_virt and mmiowb.
[S390] cio: use ARRAY_SIZE in device_id.c
[S390] cio: Fixup interface for setting options on ccw devices.
[S390] smp_call_function/smp_call_function_on locking.
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ps3fb is available, we have to disable display flipping while changing the
audio or video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 Virtual Frame Buffer Driver.
As the actual graphics hardware cannot be accessed directly by Linux, ps3fb
uses a virtual frame buffer in main memory. The actual screen image is copied
to graphics memory by the GPU on every vertical blank, by making a hypervisor
call.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fb_videomode_to_var(): reset the virtual screen parameters when converting
from an fb_videomode to an fb_var_screeninfo.
Without this the old virtual screen parameters are kept. Hence you cannot
switch to a video mode with a lower resolution on frame buffer devices that
don't support virtual screens and panning, as values are not supposed to be
rounded down when they don't fit.
I also reordered the assignments to match the order of the individual members.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbdev modedb: make more input and output pointer parameters const
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbdev modedb: Take into account the specified refresh rates for video modes
specified by name, so e.g. all of `720p', `720p@60', and `720p@50' work.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 AV Settings Driver.
The AV Settings driver is used to control Audio and Video settings. It
communicates with the policy manager through the virtual uart.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of fb drivers uses atomic_t in bad manner, since there are still some
race-prone gaps. Use mutexes to protect open/close code sections with
ref_count testing and finally use simple uint.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Denis Oliver Kropp <dok@directfb.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The FB_S3TRIO driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kzalloc instead of kmalloc+memset, twice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Acked-By: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the apparent typo CONFIG_ATY_CT with CONFIG_FB_ATY_CT.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Juergen Beisert reported that the following option doesn't work for him
video=gx1fb:1024x768-16@60
though sisfb was able to parse similar option correctly.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a proper prototype for tosh_smm() to include/linux/toshiba.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Netwinder machines with Cyber2010 crash badly when starting Xserver.
The workaround is to disable pci burst option for this revision of video
chip.
[akpm@osdl.org: cleanup]
Signed-off-by: Woody Suwalski <woodys@xandros.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although gcc seems to accept "extern" prototypes after it has seen the
"static inline" function, that's not really correct.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The end marker is missing from the driver's PCI ID table. This set of
changes adds the marker, switches to using PCI_DEVICE() and records the
table for the use in a module.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This sets up the deep register of the TGA ASIC as well as the blank pedestal
of the Bt463 RAMDAC correctly for the sync-on-green mode.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of clean-ups for the module support in the driver -- __devinit
and __devexit classifiers are now specified correctly, initialization
functions are marked static and a few unnecessary #ifdefs are removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to set the GE bit (Win32 compatibility) in the mode register;
it shall get cleared with the next subsequent update to the register anyway.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 32-plane variations of the TGA use the Bt463 RAMDAC and are therefore
DirectColor rather than TrueColor adapters. This is a set of changes to
implement the necessary bits to support this model. A couple of fixes to fix
accesses to the RAMDAC are included as a side-effect.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The direction of copying in the copyarea functions is selected incorrectly,
resulting in corruption. This is a fix.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to update the driver to the framebuffer_alloc() API.
Included, there is also a fix to a memory leak due to the colour map
allocation not being freed upon driver's removal. Aside from the fix there
are no functional changes.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some video drivers that:
- had already been marked as BROKEN in 2.6.0 three years ago and
- are still marked as BROKEN.
These are the following drivers:
- FB_CYBER
- FB_VIRGE
- FB_RETINAZ3
- FB_SUN3
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive any of these drivers, the code is
still present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a driver for S3 Trio / S3 Virge. Driver is tested with most versions
of S3 Trio and with S3 Virge/DX, on i386.
(akpm: We kind-of have support for this hardware already, but...
virgefb.c
- amiga/zorro specific,
- broken (according to Kconfig),
- uses obsolete/nonexistent interface (struct display_switch)
- recent Adrian Bunk's patch removes this driver
S3triofb.c
- ppc/openfirmware specific
- minimal functionality
- broken (according to Kconfig),
- uses obsolete/nonexistent interface (struct display_switch)
)
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the necessary callbacks to suspend and resume a host running kvm. This is
just a repeat of the cpu hotplug/unplug work.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On hotplug, we execute the hardware extension enable sequence. On unplug, we
decache any vcpus that last ran on the exiting cpu, and execute the hardware
extension disable sequence.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the inline code it replaces, this function decaches the vmcs from the cpu
it last executed on. in addition:
- vcpu_clear() works if the last cpu is also the cpu we're running on
- it is faster on larger smps by virtue of using smp_call_function_single()
Includes fix from Ingo Molnar.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will allow us to iterate over all vcpus and see which cpus they are
running on.
[akpm@osdl.org: use standard (ugly) initialisers]
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vcpu_load() can return NULL and it sometimes does in failure paths (for
example when the userspace ABI version is too old) - causing a preemption
count underflow in the ->vcpu_free() later on. So check for NULL.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Or 32-bit userspace will get confused.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We report the value of cr8 to userspace on an exit. Also let userspace change
cr8 when we re-enter the guest. The lets 64-bit guest code maintain the tpr
correctly.
Thanks for Yaniv Kamay for the idea.
Signed-off-by: Dor Laor <dor.laor@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to run the mmu testsuite on amd.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kvm mmu relies on cr0.wp being set even if the guest does not set it. The
vmx code correctly forces cr0.wp at all times, the svm code does not, so it
can't boot solaris without this patch.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just like svm.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gva_to_gpa() needs to be updated to the new walk_addr() calling convention,
otherwise it may oops under some circumstances.
Use the opportunity to remove all the code duplication in gva_to_gpa(), which
essentially repeats the calculations in walk_addr().
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Forms like "0(%rsp)" generate an instruction with an unnecessary one byte
displacement under certain circumstances. replace with the equivalent
"(%rsp)".
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think the following patch should go into the kernel, until the ISDN/CAPI
guys create the real fix for this issue.
The issue is a concurrency issue with some internal CAPI data structure
which can crash the kernel.
On my FritzCard DSL with the AVM driver it crashes about once a day without
this workaround patch. With this workaround patch it's rock-stable (at
least on UP, but I don't see why this shouldn't work on SMP as well. But
maybe I'm missing something.)
This workaround is kind of a sledgehammer which inserts a global lock to
wrap around all the critical sections. Of course, this is a scalability
issue, if you have many ISDN/CAPI cards. But it prevents a crash. So I
vote for this fix to get merged, until people come up with a better
solution. Better have a stable kernel that's less scalable, than a
crashing and useless kernel.
This bug is in the kernel since 2.6.15 (at least).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Kai Germaschewski <kai.germaschewski@gmx.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the macro CONFIG_HISAX_HFC4S8S_PCIMEM to simply HISAX_HFC4S8S_PCIMEM so
that it no longer resembles a user-settable kernel config macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on advice from K. Keil, get rid of remaining traces of defunct test
emulator for HISAX.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on advice from K. Keil, rename the special debug option
CONFIG_SERIAL_NOPAUSE_IO to ELSA_SERIAL_NOPAUSE_IO so it no longer resembles a
user-selectable kernel config option.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename some of the debugging macros for ISDN AVM so that they don't resemble
kernel config settings, as they're primarily for author debugging instead.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace misspelled CONFIG_HISAX_QUADRO with CONFIG_HISAX_SCT_QUADRO.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add proper prototypes in a header file for global code under
drivers/isdn/sc/.
Since the GNU C compiler is now able do tell us that caller and callee
disagreed about the number of arguments of setup_buffers(), this patch
also fixes this bug.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add functions prototypes for some global functions to header files
- remove unneeded "extern"s from some function prototypes
You might note that this patch results in a new warning - that's due to the
fact that with a proper prototype gcc is able to discover a broken
work_struct conversion.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add correct prototypes in header files for global functions and variables.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Wollesen ported the Bluesmoke Memory Controller driver for the Intel
5000X/V/P (Blackford/Greencreek) chipset to the in kernel EDAC model.
This patch incorporates those required changes to the edac_mc.c and edac_mc.h
core files by added new Fully Buffered DIMM interface to the EDAC Core module.
Signed-off-by: eric wollesen <ericw@xmtp.net>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an attempt of providing an interface for memory scrubbing control in
EDAC.
This patch modifies the EDAC Core to provide the Interface for memory
controller modules to implment.
The following things are still outstanding:
- K8 is the first implemenation,
The patch provide a method of configuring the K8 hardware memory scrubber
via the 'mcX' sysfs directory. There should be some fallback to a generic
scrubber implemented in software if the hardware does not support
scrubbing.
Or .. the scrubbing sysfs entry should not be visible at all.
- Only works with SDRAM, not cache,
The K8 can scrub cache and l2cache also - but I think this is not so
useful as the cache is busy all the time (one hopes).
One would also expect that cache scrubbing requires hardware support.
- Error Handling,
I would like that errors are returned to the user in "terms of file
system".
- Presentation,
I chose Bandwidth in Bytes/Second as a representation of the scrubbing
rate for the following reasons:
I like that the sysfs entries are sort-of textual, related to something
that makes sense instead of magical values that must be looked up.
"My People" wants "% main memory scrubbed per hour" others prefer "%
memory bandwidth used" as representation, "bandwith used" makes it easy to
calculate both versions in one-liner scripts.
If one later wants to scrub cache, the scaling becomes wierd for K8
changing from "blocks of 64 byte memory" to "blocks of 64 cache lines" to
"blocks of 64 bit". Using "bandwidth used" makes sense in all three cases,
(I.M.O. anyway ;-).
- Discovery,
There is no way to discover the possible settings and what they do
without reading the code and the documentation.
*I* do not know how to make that work in a practical way.
- Bugs(??),
other tools can set invalid values in the memory scrub control register,
those will read back as '-1', requiring the user to reset the scrub rate.
This is how *I* think it should be.
- Afflicting other areas of code,
I made changes to edac_mc.c and edac_mc.h which will show up globally -
this is not nice, it would be better that the memory scrubbing fuctionality
and interface could be entirely contained within the memory controller it
applies to.
Frithiof Jensen
edac_mc.c and its .h file is a CORE helper module for EDAC
driver modules. This provides the abstraction for device specific
drivers. It is fine to modify this CORE to provide help for
new features of the the drivers
doug thompson
Signed-off-by: Frithiof Jensen <frithiof.jensen@ericson.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fix/change returns the offset into the page for the ce/ue error, instead
of just 0. The e752x dram controller reads 34:6 of the linear address with
the error.
Signed-off-by: Mike Chan <mikechan@google.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reading of the DRA registers should be a byte at a time (one register at a
time) instead of 4 bytes at a time (four registers). Reading a dword at a
time retrieves erroneous information from all but the first register. A
change was made to read in each register in a loop prior to using the data in
those registers.
Signed-off-by: Brian Pomerantz <bapper@mvista.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fatal vs. non-fatal mask for the sysbus FERR status is incorrect
according to the E7520 datasheet. This patch corrects the mask to correctly
handle fatal and non-fatal errors.
Signed-off-by: Brian Pomerantz <bapper@mvista.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Of kernel subsystems that work with pids the tty layer is probably the largest
consumer. But it has the nice virtue that the assiation with a session only
lasts until the session leader exits. Which means that no reference counting
is required. So using struct pid winds up being a simple optimization to
avoid hash table lookups.
In the long term the use of pid_nr also ensures that when we have multiple pid
spaces mixed everything will work correctly.
Signed-off-by: Eric W. Biederman <eric@maxwell.lnxi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every call to is_orphaned_pgrp passed in process_group(current) which is racy
with respect to another thread changing our process group. It didn't bite us
because we were dealing with integers and the worse we would get would be a
stale answer.
In switching the checks to use struct pid to be a little more efficient and
prepare the way for pid namespaces this race became apparent.
So I simplified the calls to the more specialized is_current_pgrp_orphaned so
I didn't have to worry about making logic changes to avoid the race.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To properly implement a pid namespace I need to deal exclusively in terms of
struct pid, because pid_t values become ambiguous.
To this end session_of_pgrp is transformed to take and return a struct pid
pointer. To avoid the need to worry about reference counting I now require my
caller to hold the appropriate locks. Leaving callers repsonsible for
increasing the reference count if they need access to the result outside of
the locks.
Since session_of_pgrp currently only has one caller and that caller simply
uses only test the result for equality with another process group, the locking
change means I don't actually have to acquire the tasklist_lock at all.
tiocspgrp is also modified to take and release the lock. The logic there is a
little more complicated but nothing I won't need when I convert pgrp of a tty
to a struct pid pointer.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 24ec839c43 while fixing the locking for
signal->tty got the locking wrong for signal->session. This places our
accesses of signal->session back under the tasklist_lock where they belong.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to look at tty_old_pgrp and send SIGHUP and SIGCONT when it is
present only executes when disassociate_ctty is called from do_exit. Make
this clear by adding an explict on_exit check, and explicitly setting
tty_old_pgrp to 0.
In addition fix the locking by reading tty_old_pgrp under the siglock.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aim of this patch set is to start wrapping up the struct pid conversions.
As such this patchset culminates with the removal of kill_pg, kill_pg_info,
__kill_pg_info, do_each_task_pid, and while_each_task_pid.
kill_proc, daemonize, and kernel_thread are still in my sights but there is
still work to get to them.
The first three are basic cleanups around disassociate_ctty, while working on
converting it I found several issues. tty_old_pgrp can be a tricky concept to
wrap your head around.
1 tty: Make __proc_set_tty static.
2 tty: Clarify disassociate_ctty
3 tty: Fix the locking for signal->session in disassociate_ctty
These just stop using the old helper functions.
4 signal: Use kill_pgrp not kill_pg in the sunos compatibility code.
5 signal: Rewrite kill_something_info so it uses newer helpers.
Then the grind to convert the tty layer and all of it's helper functions to
struct pid.
6 pid: Make session_of_pgrp use struct pid instead of pid_t.
7 pid: Use struct pid for talking about process groups in exit.c
8 pid: Replace is_orphaned_pgrp with is_current_pgrp_orphaned
9 tty: Update the tty layer to work with struct pid.
A final helper function update.
10 pid: Replace do/while_each_task_pid with do/while_each_pid_task
And the removal of the functions that are now unused.
11 pid: Remove now unused do_each_task_pid and while_each_task_pid
12 pid: Remove the now unused kill_pg kill_pg_info and __kill_pg_info
All of these should be fairly simple and to the point.
This patch:
Currently all users of __proc_set_tty are in tty_io.c so make the function
static.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is adds a simple SPI EEPROM driver, providing access to the EEPROM
through sysfs much like the I2C "eeprom" driver ... except this driver
supports write access, and multiple EEPROM sizes.
From: "Tuppa, Walter" <walter.tuppa@siemens.com>
Since I have EEPROMs on SPI with different address sizing, I made some
changes to your at25.c to support them. Works perfectly. (Also includes a
small bugfix for the "what size address" test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Walter Tuppa <walter.tuppa@siemens.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new "wakealarm" sysfs attribute to RTC class devices which support
alarm operations and are wakeup-capable:
- It reads as either empty, or the scheduled alarm time as seconds
since the POSIX epoch. (That time may already have passed, since
nothing currently enforces one-shot alarm semantics.)
- It can be written with an alarm time in the future, again seconds
since the POSIX epoch, which enables the alarm.
- It can be written with an alarm time not in the future (such as 0,
the start of the POSIX epoch) to disable the alarm.
Usage examples (some need GNU date) after "cd /sys/class/rtc/rtcN":
alarm after 10 minutes:
# echo $(( $(cat since_epoch) + 10 * 60 )) > wakealarm
alarm tuesday evening 10pm:
# date -d '10pm tuesday' "+%s" > wakealarm
disable alarm:
# echo 0 > wakealarm
This resembles the /proc/acpi/alarm file in that nothing happens when the
alarm triggers ... except possibly waking the system from sleep. It's also
like that in a nasty way: not much can be done to prevent one task from
clobbering another task's alarm settings.
It differs from that file in that there's no in-kernel date parser.
Note that a few RTCs ignore rtc_wkalrm.enabled when setting alarms, or aren't
set up correctly, so they won't yet behave with this attribute.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'd like to assign NULL to kfree()d members of a structure. I can't do
that without ugly casting (see the PXA patch) when the structure pointed to
is const-qualified. I don't really see a reason why the cleanup method
isn't allowed to alter the object it should clean up. :-)
No, I didn't test the PXA patch, but I verified that the NULL-assignment
doesn't stop me from doing rmmod/insmodding my own spi_bitbang-based
driver.
Signed-off-by: Hans-Peter Nilsson <hp@axis.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A small bug-fix for spi_bitbang: it must always call the setup_transfer
function via the overridable pointer, not assume that its
spi_bitbang_setup_transfer is sufficient. Otherwise, if all options in the
transfers are default (0), the overrided function will never be called.
Granted, the function replacing it must call spi_bitbang_setup_transfer,
but it might also have other important things to do, even if the second
argument (the spi_transfer) is NULL. Tested together with the other
patches on the spi_crisv32_sser and spi_crisv32_gpio drivers (not yet in
the kernel, will IIUC be submitted as part of the usual
arch-maintainer-pushes).
Signed-off-by: Hans-Peter Nilsson <hp@axis.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the SPI controller driver for Freescale i.MX(S/L/1).
Main features summary:
> Per chip setup via board specific code and/or protocol driver.
> Per transfer setup.
> PIO transfers.
> DMA transfers.
> Managing of NULL tx / rx buffer for rd only / wr only transfers.
This patch replace patch-2.6.20-rc4-spi_imx with the following changes:
> Few cosmetic changes.
> Function map_dma_buffers now return 0 for success and -1 for failure.
> Solved a bug inside spi_imx_probe function (wrong error path).
> Solved a bug inside setup function (bad undo setup for max_speed_hz).
> For read-only transfers, always write zero bytes.
This is almost the same as the 'BIS' version sent by Andrea, except for
updating the 'DUMMY' byte so that read-only transfers shift out zeroes.
That part of the API changed recently, since some half duplex peripheral
chips require that semantic.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a SPI driver for the Microwire controller on OMAP1 chips. This
driver has been used in the Linux-OMAP tree for some time now, including
with some of those displays using standardized 9-bit commands followed by
data with 8-bit words.
Microwire only supports half duplex transfers, but that's all that most SPI
protocols need. When full duplex, or higher speeds, are needed there are
several other controllers that can be used on OMAP.
[akpm@osdl.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor Kconfig cleanup ... put the SPI_S3C24XX entry in the
correct location (alphabetical order).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the line discipline based driver for the Gigaset M101
wireless RS232 adapter. It also improves the documentation a bit.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert:
BOOL -> bool
FALSE -> false
TRUE -> true
Change a variable ('mContinue') to boolean from char, since it is used
as boolean.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use timer macros to set function and data members and to modify
expiration time.
- Use DEFINE_TIMER for global timers and do not init them at run-time in
these cases.
- del_timer_sync is common in most cases -- we want to wait for timer
function if it's still running.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Dmitry Torokhov <dtor@mail.ru> (Input bits)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
specialix, isr have 2 params
pt_regs are no longer the third parameter of isr, call sx_interrupt without
it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce the number of kernel messages the Gigaset drivers produce in case of an
excessively long device response, from one per character exceeding the limit
to one per overlong message.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not lock the cardstate structure mutex earlier than necessary.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Access to chip-internal registers should always be native-endian. This is
especially important for AVR32 since it's a big-endian architecture and the
non-raw readl() and writel() macros are defined to do little-endian
accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A patch to use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 40b20c257a by Len Brown introduced
a null pointer dereference in the appledisplay driver. This patch fixes
it.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current ccw_device_set_options() sets a specified mask of options
and clears those not specified, but there is no way to find out which
options have already been set.
In order to fix this up, introduce the following interface changes:
ccw_device_set_options() now only sets the specified bits, but does
not clear those that are not specified.
ccw_device_clear_options() clears the specified bits.
ccw_device_set_options_mask() provides the old semantics (setting only
the specified bits and clearing the others).
Device drivers now work as expected. qdio has been adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
[SCSI] zfcp: removed wrong comment
[SCSI] zfcp: use of uninitialized variable
[SCSI] zfcp: Invalid locking order
[SCSI] aic79xx: use dma_get_required_mask()
[SCSI] aic79xx: fix bracket mismatch in unused macro
[SCSI] BusLogic: Replace 'boolean' by 'bool'
[SCSI] advansys: clean up warnings
[SCSI] 53c7xx: brackets fix in uncompiled code
[SCSI] nsp_cs: remove old scsi code
[SCSI] aic79xx: make ahd_match_scb() static
[SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
[SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
[SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
[SCSI] aic94xx: update for v28 firmware
[SCSI] scsi_error: Fix lost EH commands
[SCSI] aic94xx: Add default bus reset handler
[SCSI] aic94xx: Remove TMF result code munging
[SCSI] libsas: Add an LU reset mechanism to the error handler
[SCSI] libsas: Don't BUG when connecting two expanders via wide port
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
tifm_sd: treat "status error" as normal command completion
mmc: wbsd: Remove stray kunmap_atomic()
mmc: sdhci: Stop asking for mail
mmc: sdhci: Remove driver version
mmc: wbsd: Remove driver version
drivers/isdn/gigaset/bas-gigaset.c: In function 'dump_urb':
drivers/isdn/gigaset/bas-gigaset.c:258: error: 'struct urb' has no member named 'bandwidth'
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains two fixes for RapisIO enumeration logic:
1. Fix enumeration in configurations with multiple switches. The patch adds:
a. Enumeration of an empty switch. Empty switch is a switch that
does not have any endpoint devices attached to it (except host device
or previous switch in a chain). New code assigns a phony destination
ID associated with the switch and sets up corresponding routes.
b. Adds a second pass to the enumeration to setup routes to
devices discovered after switch was scanned.
2. Fix enumeration failure when riohdid parameter has non-zero value.
Current version fails to setup response path to the host when it has
destination ID other that 0.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Acked-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
release_mem contains two copies of exactly the same code. Refactor these
into a new helper, release_tty. The only change in behaviour is that the
driver reference count is now decremented after the master tty has been
freed instead of before.
[penberg@cs.helsinki.fi: fix use-after-free in release_tty.]
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the session and pgrp fields in mxser_struct are unused.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts 'boolean' to 'bool' and removes the 'boolean' typedef.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: Jens Axboe <axboe@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the unused kernel config option PARIDE_PARPORT.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace a small number of expressions with a call to the "container_of()"
macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor number 0 (under the raw major) is reserved for the rawctl device
file, which is used to query, set, and unset raw device bindings. However,
the ioctl interface does not protect the user from specifying a raw device
with minor number 0:
$ sudo ./raw /dev/raw/raw0 /dev/VolGroup00/swap
/dev/raw/raw0: bound to major 253, minor 2
$ ls -l /dev/rawctl
ls: /dev/rawctl: No such file or directory
$ ls -l /dev/raw/raw0
crw------- 1 root root 162, 0 Jan 12 10:51 /dev/raw/raw0
$ sudo ./raw -qa
Cannot open master raw device '/dev/rawctl' (No such file or directory)
As you can see, this prevents any further raw operations from
succeeding. The fix (from Steve Fernandez) is quite simple--do not
allow the allocation of minor number 0.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Steven Fernandez <sfernand@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.
Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup kernel-doc notation in drivers/firmware/edd.c.
Add edd.c to DocBook/kernel-api.tmpl.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an "RTC framework" driver for the "CMOS" RTCs which are standard on
PCs and some other platforms. That's MC146818 compatible silicon.
Advantages of this vs. drivers/char/rtc.c (use one _or_ the other, only
one will be able to claim the RTC irq) include:
- This leverages both the new RTC framework and the driver model; both
PNPACPI and platform device modes are supported. (A separate patch
creates a platform device on PCs where PNPACPI isn't configured.)
- It supports common extensions like longer alarms. (A separate patch
exports that information from ACPI through platform_data.)
- Likewise, system wakeup events use "real driver model support", with
policy control via sysfs "wakeup" attributes and and using normal rtc
ioctls to manage wakeup. (Patch in the works. The ACPI hooks are
known; /proc/acpi/alarm can vanish. Making it work with EFI will
be a minor challenge to someone with e.g. a MiniMac.)
It's not yet been tested on non-x86 systems, without ACPI, or with HPET.
And the RTC framework will surely have teething pains on "mainstream"
PC-based systems (though must embedded Linux systems use it heavily), not
limited to sorting out the "/dev/rtc0" issue (udev easily tweaked). Also,
the ALSA rtctimer code doesn't use the new RTC API.
Otherwise, this should be a no-known-regressions replacement for the old
drivers/char/rtc.c driver, and should help the non-embedded distros (and
the new timekeeping code) start to switch to the framework.
Note also that any systems using "rtc-m48t86" are candidates to switch over
to this more functional driver; the platform data is different, and the way
bytes are read is different, but otherwise those chips should be compatible.
[akpm@osdl.org: sparc32 fix]
[akpm@osdl.org: sparc64 fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Woody Suwalski <woodys@xandros.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mostly so people can see the work in progress. This enhances the encode
function which isn't currently used in the base tree but is when using some of
the testing tty patches.
This resolves a problem with some hardware where applications got confusing
information from the tty ioctls. Correct but confusing.
In some situations asking for, say, 9600 baud actually gets you 9595 baud or
similar near-miss values. With the old code this meant that a request for
B9600 got a return of BOTHER, 9595 which programs interpreted as a failure.
The new code now works on the following basis
- If you ask for specific rate via BOTHER, you get a precise return
- If you ask for a standard Bfoo rate and the result is close you get a Bfoo
return
- If you ask for a standard Bfoo rate and get something way off you get a
BOTHER/rate return
This seems to fix up the cases I've found where this broke compatibility.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete the few remaining unnecessary calls to memset(0) after a call to
kzalloc().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify the few instances where a call to "get_zeroed_page()" is closely
followed by an unnecessary call to memset() to clear that page.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some RCU problem pointed out by Paul McKenney of IBM. These are:
The wholesale move of the command receivers list into a new list was not
safe because the list will point to the new tail during a traversal, so the
traversal will never end on a reader if this happens during a read.
Memory barriers were needed to handle proper ordering of the setting of the
IPMI interface as valid. Readers might not see proper ordering of data
otherwise.
In ipmi_smi_watcher_register(), the use of the _rcu suffix on the list is
unnecessary.
This require the list_splice_init_rcu() patch previously posted.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all calls to invalidate_inode_pages() into open-coded calls to
invalidate_mapping_pages().
Leave the invalidate_inode_pages() wrapper in place for now, marked as
deprecated.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alter the driver to use the pci probing.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove temporary or once used variables, that can be defined locally to
save some bytes.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- rename moxaChannels to moxa_port
- rename moxa_str to moxa_ports
- move board global variables into moxa_board
- move port global variables into moxa_port
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing is used from this struct but *pdev. Remove it and store only pdev.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use del_timer_sync in most timer deletions, we don't want to oops in the timer
function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove yet defined or unused macros and whitespace cleanup around the rest.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not use typedefs, use directly struct <something> instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ifdeffed functions and cleanup comments including too long license
terms.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call tty_hangup directly, we do not need a bottomhalf for this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kernel macros and functions for timer encapsulation -- do not access
fileds directly. Also del_timer on inactive is legal, so that noting if it
runs is senseless, delete these variables.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
