Commit Graph

370 Commits

Author SHA1 Message Date
NeilBrown
9cd30fdc33 md: remove needless setting of thread->timeout in raid10_quiesce
As bitmap_create and bitmap_destroy already set thread->timeout
as appropriate, there is no need to do it in raid10_quiesce.
There is a possible need to wake the thread after the timeout
has been set low, but it is better to do that where the timeout
is actually set low, in bitmap_create.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown
1b04be96f6 md: change daemon_sleep to be in 'jiffies' rather than 'seconds'.
This removes a lot of multiplications by HZ.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown
42a04b5078 md: move offset, daemon_sleep and chunksize out of bitmap structure
... and into bitmap_info.  These are all configuration parameters
that need to be set before the bitmap is created.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown
a2826aa92e md: support barrier requests on all personalities.
Previously barriers were only supported on RAID1.  This is because
other levels requires synchronisation across all devices and so needed
a different approach.
Here is that approach.

When a barrier arrives, we send a zero-length barrier to every active
device.  When that completes - and if the original request was not
empty -  we submit the barrier request itself (with the barrier flag
cleared) and then submit a fresh load of zero length barriers.

The barrier request itself is asynchronous, but any subsequent
request will block until the barrier completes.

The reason for clearing the barrier flag is that a barrier request is
allowed to fail.  If we pass a non-empty barrier through a striping
raid level it is conceivable that part of it could succeed and part
could fail.  That would be way too hard to deal with.
So if the first run of zero length barriers succeed, we assume all is
sufficiently well that we send the request and ignore errors in the
second run of barriers.

RAID5 needs extra care as write requests may not have been submitted
to the underlying devices yet.  So we flush the stripe cache before
proceeding with the barrier.

Note that the second set of zero-length barriers are submitted
immediately after the original request is submitted.  Thus when
a personality finds mddev->barrier to be set during make_request,
it should not return from make_request until the corresponding
per-device request(s) have been queued.

That will be done in later patches.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14 12:49:49 +11:00
NeilBrown
ed9bfdf1a4 md: raid1/raid10: handle allocation errors during array setup.
Both raid1 and raid10 create a mempool during startup.
If the 'alloc' function for this mempool fails, unplug_slaves
is called.
If that happens when the pool is being initialised, unplug_slaves
will try to use the 'conf' structure that isn't filled in yet, and
badness will happen.

So ensure that unplug_slaves doesn't get called unless we know
that the conf structure if fully initialised.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:44 +11:00
NeilBrown
1d9d52416c md/raid1/raid10: add a cond_resched
During 'check' of a raid1 or raid10 it is possible for the management
thread to spend a lot of time running 'memcmp' on blocks from
different devices, so make sure the thread has a chance to schedule.
raid5d already has a cond_resched (in process_stripe).

Reported-By: Lee Howard <faxguy@howardsilvan.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:32 +11:00
Dmitry Monakhov
1ef04fefe2 md: raid-1/10: fix RW bits manipulation
Recently Jens has changed bio_rw_flagged() logic by following
commit 1f98a13f62. Now it returns
bool instead of int. This broke raid1/raid10 RW bits manipulation logic.
One of visible result is BUG_ON triggering due to empty barrier
here scsi_lib.c:1108 scsi_setup_fs_cmnd()

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:20:15 +10:00
NeilBrown
3fa841d7e7 md: report device as congested when suspended
This should writeback from coming when the device is temporarily
suspended.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:10:29 +10:00
NeilBrown
0da3c6194e md: Improve name of threads created by md_register_thread
The management thread for raid4,5,6 arrays are all called
mdX_raid5, independent of the actual raid level, which is wrong and
can be confusion.

So change md_register_thread to use the name from the personality
unless no alternate name (like 'resync' or 'reshape') is given.

This is simpler and more correct.

Cc: Jinzc <zhenchengjin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:09:45 +10:00
NeilBrown
a9f326ebf2 md: remove sparse waring "symbol xxx shadows an earlier one"
Rename some variable and remove some duplicate definitions
to avoid there warnings.  None of them are actual errors.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:06:41 +10:00
Jens Axboe
1f98a13f62 bio: first step in sanitizing the bio->bi_rw flag testing
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-09-11 14:33:31 +02:00
Andre Noll
ac5e7113e7 md: Push down data integrity code to personalities.
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.

md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity.  The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().

The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.

For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-08-03 10:59:47 +10:00
Martin K. Petersen
8f6c2e4b32 md: Use new topology calls to indicate alignment and I/O sizes
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.

Also indicate preferred I/O sizes where applicable.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-07-01 11:13:45 +10:00
Andre Noll
8c6ac868b1 md: Push down reconstruction log message to personality code.
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).

Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:48:06 +10:00
Andre Noll
9d8f036362 md: Make mddev->chunk_size sector-based.
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics.  Since

	is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
				  = is_power_of_2(chunk_sectors)

these bits don't need an adjustment for the shift.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:45:01 +10:00
raz ben yehuda
964e7913b0 md: raid10: chunk size check in run
have raid10 check chunk size in run method instead of in md

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 17:01:22 +10:00
NeilBrown
070ec55d07 md: remove mddev_to_conf "helper" macro
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.

So open code the macro everywhere and remove the pointless cast.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:54:21 +10:00
Martin K. Petersen
ae03bf639a block: Use accessor functions for queue limits
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 23:22:54 +02:00
NeilBrown
1805556912 md/raid10: don't clear bitmap during recovery if array will still be degraded.
If we have a raid10 with multiple missing devices, and we recover just
one of these to a spare, then we risk (depending on the bitmap and
array chunk size) clearing bits of the bitmap for which recovery isn't
complete (because a device is still missing).

This can lead to a subsequent "re-add" being recovered without
any IO happening, which would result in loss of data.

This patch takes the safe approach of not clearing bitmap bits
if the array will still be degraded.

This patch is suitable for all active -stable kernels.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-05-07 12:48:10 +10:00
Christoph Hellwig
8f3d8ba20e block: move bio list helpers into bio.h
It's used by DM and MD and generally useful, so move the bio list
helpers into bio.h.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-04-15 08:28:09 +02:00
Dan Williams
b522adcde9 md: 'array_size' sysfs attribute
Allow userspace to set the size of the array according to the following
semantics:

1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
   a) If size is set before the array is running, do_md_run will fail
      if size is greater than the default size
   b) A reshape attempt that reduces the default size to less than the set
      array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
   kernel and reverts to the size reported by the personality

Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size.  Resync/reshape operations
always follow the default size.

Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 15:00:31 +11:00
Dan Williams
1f403624bd md: centralize ->array_sectors modifications
Get personalities out of the business of directly modifying
->array_sectors.  Lays groundwork to introduce policy on when
->array_sectors can be modified.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:59:03 +11:00
Dan Williams
80c3a6ce4b md: add 'size' as a personality method
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested.  For personalities that do not reshape emit
a warning if anything but the default size is requested.

In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:57:49 +11:00
NeilBrown
409c57f380 md: enable suspend/resume of md devices.
To be able to change the 'level' of an md/raid array, we need to
suspend the device so that no requests are active - then move some
pointers around etc.

The code already keeps counts of active requests and the ->quiesce
function can be used to wait until those counts hit zero.
However the quiesce function blocks new requests once they are all
ready 'inside' the personality module, and that is too late if we want
to replace the personality modules.

So make all md requests come in through a common md_make_request
function that keeps track of how many requests have entered the
modules but may not yet be on the internal reference counts.
Allow md_make_request to be blocked when we want to suspend the
device, and make it possible to wait for all those in-transit requests
to be added to internal lists so that ->quiesce can wait for them.

There is still a problem that when a request completes, we drop the
ref count inside the personality code so there is a short time between
when the refcount hits zero, and when the personality code is no
longer being used.
The personality code never blocks (schedule or spinlock) between
dropping the refcount and exiting the routine, so this should be safe
(as put_module calls synchronize_sched() before unmapping the module
code).

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:39:39 +11:00
Andre Noll
58c0fed400 md: Make mddev->size sector-based.
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.

All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.

In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown
43b2e5d86d md: move md_k.h from include/linux/raid/ to drivers/md/
It really is nicer to keep related code together..

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown
bff61975b3 md: move lots of #include lines out of .h files and into .c
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h

Remove include/raid/md.h as its only remaining use was to #include
other files.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
Christoph Hellwig
ef740c372d md: move headers out of include/linux/raid/
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away.  md.h is left where it is for now as there
are some uses from the outside.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:27:03 +11:00
NeilBrown
73d5c38a95 md: avoid races when stopping resync.
There has been a race in raid10 and raid1 for a long time
which has only recently started showing up due to a scheduler changed.

When a sync_read request finishes, as soon as reschedule_retry
is called, another thread can mark the resync request as having
completed, so md_do_sync can finish, ->stop can be called, and
->conf can be freed.  So using conf after reschedule_retry is not
safe.

Similarly, when finishing a sync_write, calling md_done_sync must be
the last thing we do, as it allows a chain of events which will free
conf and other data structures.

The first of these requires action in raid10.c
The second requires action in raid1.c and raid10.c

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
NeilBrown
78200d45cd md/raid10: Don't call bitmap_cond_end_sync when we are doing recovery.
For raid1/4/5/6, resync (fixing inconsistencies between devices) is
very similar to recovery (rebuilding a failed device onto a spare).
The both walk through the device addresses in order.

For raid10 it can be quite different.  resync follows the 'array'
address, and makes sure all copies are the same.  Recover walks
through 'device' addresses and recreates each missing block.

The 'bitmap_cond_end_sync' function allows the write-intent-bitmap
(When present) to be updated to reflect a partially completed resync.
It makes assumptions which mean that it does not work correctly for
raid10 recovery at all.

In particularly, it can cause bitmap-directed recovery of a raid10 to
not recovery some of the blocks that need to be recovered.

So move the call to bitmap_cond_end_sync into the resync path, rather
than being in the common "resync or recovery" path.


Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
NeilBrown
09b4068a7f md/raid10: Don't skip more than 1 bitmap-chunk at a time during recovery.
When doing recovery on a raid10 with a write-intent bitmap, we only
need to recovery chunks that are flagged in the bitmap.

However if we choose to skip a chunk as it isn't flag, the code
currently skips the whole raid10-chunk, thus it might not recovery
some blocks that need recovering.

This patch fixes it.

In case that is confusing, it might help to understand that there
is a 'raid10 chunk size' which guides how data is distributed across
the devices, and a 'bitmap chunk size' which says how much data
corresponds to a single bit in the bitmap.

This bug only affects cases where the bitmap chunk size is smaller
than the raid10 chunk size.



Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
Cheng Renquan
159ec1fc06 md: use list_for_each_entry macro directly
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.

But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.

In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.

Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-01-09 08:31:08 +11:00
NeilBrown
a53a6c8575 md: fix bug in raid10 recovery.
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
  commit 6c2fce2ef6
and so is a bug in 2.6.27 and .28-rc.

Thanks to Thomas Backlund for bisecting to find this.

Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org

Signed-off-by: NeilBrown <neilb@suse.de>
2008-11-06 17:28:20 +11:00
Stephen Rothwell
255707274e md: build failure due to missing delay.h
Today's linux-next build (powerpc ppc64_defconfig) failed like this:

drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'

Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations").  I added
the following patch.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-15 21:57:05 +11:00
NeilBrown
4bbf3771ca md: Relax minimum size restrictions on chunk_size.
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.

This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.

For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe.  For other raid personalities, this restriction is
not needed at all and can be dropped.

So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Denis ChengRq
6feef531f5 block: mark bio_split_pool static
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;

then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.

Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:57:05 +02:00
Tejun Heo
074a7aca7a block: move stats from disk to part0
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...

* part_stat_*() now updates part0 together if the specified partition
  is not part0.  ie. part_stat_*() are now essentially all_stat_*().

* {disk|all}_stat_*() are gone.

* part_round_stats() is updated similary.  It handles part0 stats
  automatically and disk_round_stats() is killed.

* part_{inc|dec}_in_fligh() is implemented which automatically updates
  part0 stats for parts other than part0.

* disk_map_sector_rcu() is updated to return part0 if no part matches.
  Combined with the above changes, this makes NULL special case
  handling in callers unnecessary.

* Separate stats show code paths for disk are collapsed into part
  stats show code paths.

* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()

While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:08 +02:00
Tejun Heo
c995905916 block: fix diskstats access
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters.  It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.

This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access).  diskstats access
should always be enclosed between the two functions.  As such, there's
no need for the versions which disables preemption.  They're removed
and double underbars ones are renamed to drop the underbars.  As an
extra argument is added, there's no danger of using the old version
unconverted.

disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.

This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others.  Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:06 +02:00
Jens Axboe
960e739d9e block: raid fixups for removal of bi_hw_segments
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
Mikulas Patocka
5df97b91b5 drop vmerge accounting
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
NeilBrown
0310fa216d Allow raid10 resync to happening in larger chunks.
The raid10 resync/recovery code currently limits the amount of
in-flight resync IO to 2Meg.  This was copied from raid1 where
it seems quite adequate.  However for raid10, some layouts require
a bit of seeking to perform a resync, and allowing a larger buffer
size means that the seeking can be significantly reduced.

There is probably no real need to limit the amount of in-flight
IO at all.  Any shortage of memory will naturally reduce the
amount of buffer space available down to a set minimum, and any
concurrent normal IO will quickly cause resync IO to back off.

The only problem would be that normal IO has to wait for all resync IO
to finish, so a very large amount of resync IO could cause unpleasant
latency when normal IO starts up.

So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is
available) which seems to be a good amount.  Also reduce the amount
of memory reserved as there is no need to keep 2Meg just for resync if
memory is tight.

Thanks to Keld for the suggestion.

Cc: Keld Jørn Simonsen <keld@dkuug.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
Linus Torvalds
1e24b15b26 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
  md: raid10: wake up frozen array
  md: do not count blocked devices as spares
  md: do not progress the resync process if the stripe was blocked
  md: delay notification of 'active_idle' to the recovery thread
  md: fix merge error
  md: move async_tx_issue_pending_all outside spin_lock_irq
2008-08-01 11:56:07 -07:00
Arthur Jones
388667bed5 md: raid10: wake up frozen array
When rescheduling a bio in raid10, we wake up
the md thread, but if the array is frozen, this
will have no effect.  This causes the array to
remain frozen for eternity.  We add a wake_up
to allow the array to de-freeze.  This code is
nearly identical to the raid1 code, which has
this fix already.

Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-01 12:55:14 +10:00
Linus Torvalds
8a392625b6 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (52 commits)
  md: Protect access to mddev->disks list using RCU
  md: only count actual openers as access which prevent a 'stop'
  md: linear: Make array_size sector-based and rename it to array_sectors.
  md: Make mddev->array_size sector-based.
  md: Make super_type->rdev_size_change() take sector-based sizes.
  md: Fix check for overlapping devices.
  md: Tidy up rdev_size_store a bit:
  md: Remove some unused macros.
  md: Turn rdev->sb_offset into a sector-based quantity.
  md: Make calc_dev_sboffset() return a sector count.
  md: Replace calc_dev_size() by calc_num_sectors().
  md: Make update_size() take the number of sectors.
  md: Better control of when do_md_stop is allowed to stop the array.
  md: get_disk_info(): Don't convert between signed and unsigned and back.
  md: Simplify restart_array().
  md: alloc_disk_sb(): Return proper error value.
  md: Simplify sb_equal().
  md: Simplify uuid_equal().
  md: sb_equal(): Fix misleading printk.
  md: Fix a typo in the comment to cmd_match().
  ...
2008-07-21 10:29:12 -07:00
Andre Noll
f233ea5c9e md: Make mddev->array_size sector-based.
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:22 +10:00
Alasdair G Kergon
cc371e66e3 Add bvec_merge_data to handle stacked devices and ->merge_bvec()
When devices are stacked, one device's merge_bvec_fn may need to perform
the mapping and then call one or more functions for its underlying devices.

The following bio fields are used:
  bio->bi_sector
  bio->bi_bdev
  bio->bi_size
  bio->bi_rw  using bio_data_dir()

This patch creates a new struct bvec_merge_data holding a copy of those
fields to avoid having to change them directly in the struct bio when
going down the stack only to have to change them back again on the way
back up.  (And then when the bio gets mapped for real, the whole
exercise gets repeated, but that's a problem for another day...)

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-03 13:21:15 +02:00
Neil Brown
199050ea1f rationalise return value for ->hot_add_disk method.
For all array types but linear, ->hot_add_disk returns 1 on
success, 0 on failure.
For linear, it returns 0 on success and -errno on failure.

This doesn't cause a functional problem because the ->hot_add_disk
function of linear is used quite differently to the others.
However it is confusing.

So convert all to return 0 for success or -errno on failure
and fix call sites to match.

Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:31:33 +10:00
Neil Brown
6c2fce2ef6 Support adding a spare to a live md array with external metadata.
i.e. extend the 'md/dev-XXX/slot' attribute so that you can
tell a device to fill an vacant slot in an and md array.

Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:31:31 +10:00
Neil Brown
8c2e870a62 Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
If, while assembling an array, we find a device which is not fully
in-sync with the array, it is important to set the "fullsync" flags.
This is an exact analog to the setting of this flag in hot_add_disk
methods.

Currently, only v1.x metadata supports having devices in an array
which are not fully in-sync (it keep track of how in sync they are).
The 'fullsync' flag only makes a difference when a write-intent bitmap
is being used.  In this case it tells recovery to ignore the bitmap
and recovery all blocks.

This fix is already in place for raid1, but not raid5/6 or raid10.

So without this fix, a raid1 ir raid4/5/6 array with version 1.x
metadata and a write intent bitmaps, that is stopped in the middle
of a recovery, will appear to complete the recovery instantly
after it is reassembled, but the recovery will not be correct.

If you might have an array like that, issueing
   echo repair > /sys/block/mdXX/md/sync_action

will make sure recovery completes properly.

Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:30:52 +10:00
NeilBrown
dfc7064500 md: restart recovery cleanly after device failure.
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.

For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.

We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
  - We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
    which causes the recovery not be be checkpointed.
  - We remove spares and then re-added them which loses important state
    information.

The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed.  If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error.  So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.

Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded).  Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.

Issue:  If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available,  do we want to:
 1/ complete the current rebuild, then go back and rebuild the new spare or
 2/ restart the rebuild from the start and rebuild both devices in
    parallel.

Both options can be argued for.  The code currently takes option 2 as
  a/ this requires least code change
  b/ this results in a minimally-degraded array in minimal time.

Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Neil Brown
e7e72bf641 Remove blkdev warning triggered by using md
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.

For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock.  So always initialise that lock when allocated.

With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.

Thanks to Dan Williams for review and fixing the silly bugs.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:15 -07:00
Harvey Harrison
cb6969e8cd misc: fix integer as NULL pointer warnings
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-08 10:46:55 -07:00
Dan Williams
6bfe0b4990 md: support blocking writes to an array on device failure
Allows a userspace metadata handler to take action upon detecting a device
failure.

Based on an original patch by Neil Brown.

Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
 userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:33 -07:00
Nick Andrew
d7a420c947 raid: remove leading TAB on printk messages
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character.  It may also output a trailing space
before newline.  klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file.  This looks ugly.

Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar.  Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.

Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
K.Tanaka
a07e6ab41b md: the md RAID10 resync thread could cause a md RAID10 array deadlock
This message describes another issue about md RAID10 found by testing the
2.6.24 md RAID10 using new scsi fault injection framework.

Abstract:

When a scsi error results in disabling a disk during RAID10 recovery, the
resync threads of md RAID10 could stall.

This case, the raid array has already been broken and it may not matter.  But
I think stall is not preferable.  If it occurs, even shutdown or reboot will
fail because of resource busy.

The deadlock mechanism:

The r10bio_s structure has a "remaining" member to keep track of BIOs yet to
be handled when recovering.  The "remaining" counter is incremented when
building a BIO in sync_request() and is decremented when finish a BIO in
end_sync_write().

If building a BIO fails for some reasons in sync_request(), the "remaining"
should be decremented if it has already been incremented.  I found a case
where this decrement is forgotten.  This causes a md_do_sync() deadlock
because md_do_sync() waits for md_done_sync() called by end_sync_write(), but
end_sync_write() never calls md_done_sync() because of the "remaining" counter
mismatch.

For example, this problem would be reproduced in the following case:

Personalities : [raid10]
md0 : active raid10 sdf1[4] sde1[5](F) sdd1[2] sdc1[1] sdb1[6](F)
      3919616 blocks 64K chunks 2 near-copies [4/2] [_UU_]
      [>....................]  recovery =  2.2% (45376/1959808) finish=0.7min speed=45376K/sec

This case, sdf1 is recovering, sdb1 and sde1 are disabled.
An additional error with detaching sdd will cause a deadlock.

md0 : active raid10 sdf1[4] sde1[5](F) sdd1[6](F) sdc1[1] sdb1[7](F)
      3919616 blocks 64K chunks 2 near-copies [4/1] [_U__]
      [=>...................]  recovery =  5.0% (99520/1959808) finish=5.9min speed=5237K/sec

 2739 ?        S<     0:17 [md0_raid10]
28608 ?        D<     0:00 [md0_resync]
28629 pts/1    Ss     0:00 bash
28830 pts/1    R+     0:00 ps ax
31819 ?        D<     0:00 [kjournald]

The resync thread keeps working, but actually it is deadlocked.

Patch:
By this patch, the remaining counter will be decremented if needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
1c830532f6 md: fix possible raid1/raid10 deadlock on read error during resync
Thanks to K.Tanaka and the scsi fault injection framework, here is a fix for
another possible deadlock in raid1/raid10 error handing.

If a read request returns an error while a resync is happening and a resync
request is pending, the attempt to fix the error will block until the resync
progresses, and the resync will block until the read request completes.  Thus
a deadlock.

This patch fixes the problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
Keld Simonsen
8ed3a19563 md: don't attempt read-balancing for raid10 'far' layouts
This patch changes the disk to be read for layout "far > 1" to always be the
disk with the lowest block address.

Thus the chunks to be read will always be (for a fully functioning array) from
the first band of stripes, and the raid will then work as a raid0 consisting
of the first band of stripes.

Some advantages:

The fastest part which is the outer sectors of the disks involved will be
used.  The outer blocks of a disk may be as much as 100 % faster than the
inner blocks.

Average seek time will be smaller, as seeks will always be confined to the
first part of the disks.

Mixed disks with different performance characteristics will work better, as
they will work as raid0, the sequential read rate will be number of disks
involved times the IO rate of the slowest disk.

If a disk is malfunctioning, the first disk which is working, and has the
lowest block address for the logical block will be used.

Signed-off-by: Keld Simonsen <keld@dkuug.dk>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
a35e63efa1 md: fix deadlock in md/raid1 and md/raid10 when handling a read error
When handling a read error, we freeze the array to stop any other IO while
attempting to over-write with correct data.

This is done in the raid1d(raid10d) thread and must wait for all submitted IO
to complete (except for requests that failed and are sitting in the retry
queue - these are counted in ->nr_queue and will stay there during a freeze).

However write requests need attention from raid1d as bitmap updates might be
required.  This can cause a deadlock as raid1 is waiting for requests to
finish that themselves need attention from raid1d.

So we create a new function 'flush_pending_writes' to give that attention, and
call it in freeze_array to be sure that we aren't waiting on raid1d.

Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this
problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:17 -08:00
NeilBrown
d089c6af10 md: change ITERATE_RDEV to rdev_for_each
As this is more in line with common practice in the kernel.  Also swap the
args around to be more like list_for_each.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:19 -08:00
NeilBrown
c620727779 md: allow a maximum extent to be set for resyncing
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.

Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:18 -08:00
NeilBrown
b47490c9bc md: Update md bitmap during resync.
Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync.  Rather the entire bitmap is updated
when the resync completes.

This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.

However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap.  Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.

[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:18 -08:00
Alan D. Brunelle
2ad8b1ef11 Add UNPLUG traces to all appropriate places
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.

Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-09 13:41:32 +01:00
Jens Axboe
fd5d806266 block: convert blkdev_issue_flush() to use empty barriers
Then we can get rid of ->issue_flush_fn() and all the driver private
implementations of that.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-16 11:05:02 +02:00
NeilBrown
6712ecf8f6 Drop 'size' argument from bio_endio and bi_end_io
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant.  Remove it.

Now there is no need for bio_endio to subtract the size completed
from bi_size.  So don't do that either.

While we are at it, change bi_end_io to return void.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10 09:25:57 +02:00
Arne Redlich
f6f953aa99 md: handle writes to broken raid10 arrays gracefully
When writing to a broken array, raid10 currently happily emits empty bio
lists.  IOW, the master bio will never be completed, sending writers to
UNINTERRUPTIBLE_SLEEP forever.

Signed-off-by: Arne Redlich <agr@powerkom-dd.de>
Acked-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31 15:39:38 -07:00
Maik Hampel
14e713446a md: raid10: fix use-after-free of bio
In case of read errors raid10d tries to print a nice error message,
unfortunately using data from an already put bio.

Signed-off-by: Maik Hampel <m.hampel@gmx.de>
Acked-By: NeilBrown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31 15:39:38 -07:00
Jens Axboe
165125e1e4 [BLOCK] Get rid of request_queue_t typedef
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-07-24 09:28:11 +02:00
NeilBrown
4ad1366376 md: change bitmap_unplug and others to void functions
bitmap_unplug only ever returns 0, so it may as well be void.  Two callers try
to print a message if it returns non-zero, but that message is already printed
by bitmap_file_kick.

write_page returns an error which is not consistently checked.  It always
causes BITMAP_WRITE_ERROR to be set on an error, and that can more
conveniently be checked.

When the return of write_page is checked, an error causes bitmap_file_kick to
be called - so move that call into write_page - and protect against recursive
calls into bitmap_file_kick.

bitmap_update_sb returns an error that is never checked.

So make these 'void' and be consistent about checking the bit.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 10:23:15 -07:00
NeilBrown
af03b8e4e8 md: fix two raid10 bugs
1/ When resyncing a degraded raid10 which has more than 2 copies of each block,
  garbage can get synced on top of good data.

2/ We round the wrong way in part of the device size calculation, which
  can cause confusion.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-06-16 13:16:15 -07:00
NeilBrown
64a742bc61 [PATCH] md: fix raid10 recovery problem.
There are two errors that can lead to recovery problems with raid10
when used in 'far' more (not the default).

Due to a '>' instead of '>=' the wrong block is located which would result in
garbage being written to some random location, quite possible outside the
range of the device, causing the newly reconstructed device to fail.

The device size calculation had some rounding errors (it didn't round when it
should) and so recovery would go a few blocks too far which would again cause
a write to a random block address and probably a device error.

The code for working with device sizes was fairly confused and spread out, so
this has been tided up a bit.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-01 14:53:36 -08:00
Lars Ellenberg
e3881a6816 [PATCH] md: pass down BIO_RW_SYNC in raid{1,10}
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.

Fixing this in raid1 and raid10 seems to be straightforward enough.

For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.

Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2007-01-11 18:18:21 -08:00
NeilBrown
802ba064c4 [PATCH] md: Don't assume that READ==0 and WRITE==1 - use the names explicitly
Thanks Jens for alerting me to this.

Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <raziebe@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:48 -08:00
Randy Dunlap
969b755aad [PATCH] md: fix printk format warnings, seen on powerpc64:
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:52 -07:00
NeilBrown
2e333e8986 [PATCH] md: fix calculation of ->degraded for multipath and raid10
Two less-used md personalities have bugs in the calculation of ->degraded (the
extent to which the array is degraded).

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-21 13:35:05 -07:00
NeilBrown
0d12922823 [PATCH] md: define ->congested_fn for raid1, raid10, and multipath
raid1, raid10 and multipath don't report their 'congested' status through
bdi_*_congested, but should.

This patch adds the appropriate functions which just check the 'congested'
status of all active members (with appropriate locking).

raid1 read_balance should be modified to prefer devices where
bdi_read_congested returns false.  Then we could use the '&' branch rather
than the '|' branch.  However that should would need some benchmarking first
to make sure it is actually a good idea.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown
c04be0aa82 [PATCH] md: Improve locking around error handling
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.

So:
  - use test-and-set and test-and-clear to synchonise
    the In_sync bits with the ->degraded count
  - use the spinlock to protect updates to the
    degraded count (could use an atomic_t but that
    would be a bigger change in code, and isn't
    really justified)
  - remove un-necessary locking in raid5

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown
76186dd8b7 [PATCH] md: remove 'working_disks' from raid10 state
It isn't needed as mddev->degraded contains equivalent info.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown
850b2b420c [PATCH] md: replace magic numbers in sb_dirty with well defined bit flags
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
   Some device state has changed requiring superblock update
   on all devices.
MD_CHANGE_CLEAN
   The array has transitions from 'clean' to 'dirty' or back,
   requiring a superblock update on active devices, but possibly
   not on spares
MD_CHANGE_PENDING
   A superblock update is underway.

We wait for an update to complete by waiting for all flags to be clear.  A
flag can be set at any time, even during an update, without risk that the
change will be lost.

Stop exporting md_update_sb - isn't needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown
6814d5368d [PATCH] md: factor out part of raid10d into a separate function.
raid10d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown
d695043259 [PATCH] md: include sector number in messages about corrected read errors
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.

[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown
8838832830 [PATCH] md: Calculate correct array size for raid10 in new offset mode
The size calculation made assumtion which the new offset mode didn't
follow.  This gets the size right in all cases.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
c93983bf51 [PATCH] md: support stripe/offset mode in raid10
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes.  e.g.

  A  B  C  D
  D  A  B  C
  E  F  G  H
  H  E  F  G

(columns are drives, rows are stripes, LETTERS are chunks of data).

This is similar to raid10's 'far' mode, but not quite the same.  So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
5fd6c1dce0 [PATCH] md: allow checkpoint of recovery with version-1 superblock
For a while we have had checkpointing of resync.  The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.

Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
8932c2e0dc [PATCH] md: remove arbitrary limit on chunk size
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg.  Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count.  Then
no limit would be needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
NeilBrown
e0a33270ed [PATCH] md: Fixed refcounting/locking when attempting read error correction in raid10
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors.  This reference must be taken under an rcu lock.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:42 -07:00
NeilBrown
df30d0f4ca [PATCH] md: Avoid oops when attempting to fix read errors on raid10
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:42 -07:00
Eric Sesterhenn
b638548384 BUG_ON() Conversion in md/raid10.c
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away

Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-04-02 13:34:29 +02:00
NeilBrown
29fc7e3e70 [PATCH] md: Assorted little md fixes
- version-1 superblock
  + The default_bitmap_offset is in sectors, not bytes.
  + the 'size' field in the superblock is in sectors, not KB
- raid0_run should return a negative number on error, not '1'
- raid10_read_balance should not return a valid 'disk' number if
     ->rdev turned out to be NULL
- kmem_cache_destroy doesn't like being passed a NULL.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-03 08:32:00 -08:00
Arjan van de Ven
858119e159 [PATCH] Unlinline a bunch of other functions
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-14 18:27:06 -08:00
NeilBrown
4dbcdc751c [PATCH] md: count corrected read errors per drive
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.

Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:09 -08:00
NeilBrown
d9d166c2a9 [PATCH] md: allow array level to be set textually via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:09 -08:00
NeilBrown
f188593ee7 [PATCH] md: fix typo in comment
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:07 -08:00
NeilBrown
1345b1d8ad [PATCH] md: define and use safe_put_page for md
md sometimes call put_page on NULL pointers (treating it like kfree).  This is
not safe, so define and use a 'safe_put_page' which checks for NULL.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:07 -08:00
NeilBrown
097426f689 [PATCH] md: fix possible problem in raid1/raid10 error overwriting
The code to overwrite/reread for addressing read errors in raid1/raid10
currently assumes that the read will not alter the buffer which could be used
to write to the next device.  This is not a safe assumption to make.

So we split the loops into a overwrite loop and a separate re-read loop, so
that the writing is complete before reading is attempted.

Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:06 -08:00
NeilBrown
2604b703b6 [PATCH] md: remove personality numbering from md
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).

These personalities have fairly artificial 'numbers'.  The numbers
are use to:
 1- provide an index into an array where the various personalities
    are recorded
 2- identify the module (via an alias) which implements are particular
    personality.

Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely).  Module identification can be done using an alias
based on level rather than 'personality' number.

The current 'raid5' modules support two level (4 and 5) but only one
personality.  This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.

With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.

This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
 This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:06 -08:00
NeilBrown
a24a8dd858 [PATCH] md: break out of a loop that doesn't need to run to completion
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:06 -08:00
NeilBrown
9ffae0cf3e [PATCH] md: convert md to use kzalloc throughout
Replace multiple kmalloc/memset pairs with kzalloc calls.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown
2d1f3b5d1b [PATCH] md: clean up 'page' related names in md
Substitute:

  page_cache_get -> get_page
  page_cache_release -> put_page
  PAGE_CACHE_SHIFT -> PAGE_SHIFT
  PAGE_CACHE_SIZE -> PAGE_SIZE
  PAGE_CACHE_MASK -> PAGE_MASK
  __free_page -> put_page

because we aren't using the page cache, we are just using pages.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown
0eb3ff12aa [PATCH] md: raid10 read-error handling - resync and read-only
Add in correct read-error handling for resync and read-only situations.

When read-only, we don't over-write, so we need to mark the failed drive in
the r10_bio so we don't re-try it.  During resync, we always read all blocks,
so if there is a read error, we simply over-write it with the good block that
we found (assuming we found one).

Note that the recovery case still isn't handled in an interesting way.  There
is nothing useful to do for the 2-copies case.  If there are 3 or more copies,
then we could try reading from one of the non-missing copies, but this is a
bit complicated and very rarely would be used, so I'm leaving it for now.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown
4443ae10ca [PATCH] md: auto-correct correctable read errors in raid10
Largely just a cross-port from raid1.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown
18f08819f4 [PATCH] md: support check-without-repair of raid10 arrays
Also keep count on the number of errors found.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:04 -08:00
NeilBrown
6cce3b23f6 [PATCH] md: write intent bitmap support for raid10
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:03 -08:00
NeilBrown
0a27ec96b6 [PATCH] md: improve raid10 "IO Barrier" concept
raid10 needs to put up a barrier to new requests while it does resync or other
background recovery.  The code for this is currently open-coded, slighty
obscure by its use of two waitqueues, and not documented.

This patch gathers all the related code into 4 functions, and includes a
comment which (hopefully) explains what is happening.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:02 -08:00
NeilBrown
22dfdf5212 [PATCH] md: improve read speed to raid10 arrays using 'far copies'
raid10 has two different layouts.  One uses near-copies (so multiple
copies of a block are at the same or similar offsets of different
devices) and the other uses far-copies (so multiple copies of a block
are stored a greatly different offsets on different devices).  The point
of far-copies is that it allows the first section (normally first half)
to be layed out in normal raid0 style, and thus provide raid0 sequential
read performance.

Unfortunately, the read balancing in raid10 makes some poor decisions
for far-copies arrays and you don't get the desired performance.  So
turn off that bad bit of read_balance for far-copies arrays.

With this patch, read speed of an 'f2' array is comparable with a raid0
with the same number of devices, though write speed is ofcourse still
very slow.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-28 14:42:25 -08:00
NeilBrown
b2d444d7ad [PATCH] md: convert 'faulty' and 'in_sync' fields to bits in 'flags' field
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-09 07:56:38 -08:00
Suzanne Wood
d6065f7bf8 [PATCH] md: provide proper rcu_dereference / rcu_assign_pointer annotations in md
Acked-by: <paulmck@us.ibm.com>
Signed-off-by: Suzanne Wood <suzannew@cs.pdx.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-09 07:56:37 -08:00
Jens Axboe
a362357b6c [BLOCK] Unify the seperate read/write io stat fields into arrays
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).

Signed-off-by: Jens Axboe <axboe@suse.de>
2005-11-01 09:26:16 +01:00
Al Viro
dd0fc66fb3 [PATCH] gfp flags annotations - part 1
- added typedef unsigned int __nocast gfp_t;

 - replaced __nocast uses for gfp flags with gfp_t - it gives exactly
   the same warnings as far as sparse is concerned, doesn't change
   generated code (from gcc point of view we replaced unsigned int with
   typedef) and documents what's going on far better.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-10-08 15:00:57 -07:00
NeilBrown
87fc767b83 [PATCH] md: fix BUG when raid10 rebuilds without enough drives
This shouldn't be a BUG.  We should cope.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 16:39:15 -07:00
NeilBrown
6d508242b2 [PATCH] md: fix raid10 assembly when too many devices are missing
If you try to assemble an array with too many missing devices, raid10 will now
reject the attempt, instead of allowing it.

Also check when hot-adding a drive and refuse the hot-add if the array is
beyond hope.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 16:39:14 -07:00
NeilBrown
e5dcdd80a6 [PATCH] md: fail IO request to md that require a barrier.
md does not yet support BIO_RW_BARRIER, so be honest about it and fail
(-EOPNOTSUPP) any such requests.

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 16:39:09 -07:00
NeilBrown
3ec67ac1a3 [PATCH] md: fix minor error in raid10 read-balancing calculation.
'this_sector' is a virtual (array) address while 'head_position' is a physical
(device) address, so substraction doesn't make any sense.  devs[slot].addr
should be used instead of this_sector.

However, this patch doesn't make much practical different to the read
balancing due to the effects of later code.

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 16:39:09 -07:00
Jesper Juhl
990a8baf56 [PATCH] md: remove unneeded NULL checks before kfree
This patch removes some unneeded checks of pointers being NULL before
calling kfree() on them.  kfree() handles NULL pointers just fine, checking
first is pointless.

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-21 19:07:48 -07:00
NeilBrown
3d310eb7b3 [PATCH] md: fix deadlock due to md thread processing delayed requests.
Before completing a 'write' the md superblock might need to be updated.
This is best done by the md_thread.

The current code schedules this up and queues the write request for later
handling by the md_thread.

However some personalities (Raid5/raid6) will deadlock if the md_thread
tries to submit requests to its own array.

So this patch changes things so the processes submitting the request waits
for the superblock to be written and then submits the request itself.

This fixes a recently-created deadlock in raid5/raid6

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-21 19:07:46 -07:00
NeilBrown
57afd89f98 [PATCH] md: improve the interface to sync_request
1/ change the return value (which is number-of-sectors synced)
 from 'int' to 'sector_t'.
 The number of sectors is usually easily small enough to fit
 in an int, but if resync needs to abort, it may want to return
 the total number of remaining sectors, which could be large.
 Also errors cannot be returned as negative numbers now, so use
 0 instead
2/ Add a 'skipped' return parameter to allow the array to report
 that it skipped the sectors.  This allows md to take this into account
 in the speed calculations.
 Currently there is no important skipping, but the bitmap-based-resync
 that is coming will use this.

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-21 19:07:43 -07:00
NeilBrown
06d91a5fe0 [PATCH] md: improve locking on 'safemode' and move superblock writes
When md marks the superblock dirty before a write, it calls
generic_make_request (to write the superblock) from within
generic_make_request (to write the first dirty block), which could cause
problems later.

With this patch, the superblock write is always done by the helper thread, and
write request are delayed until that write completes.

Also, the locking around marking the array dirty and writing the superblock is
improved to avoid possible races.

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-21 19:07:43 -07:00
NeilBrown
fca4d848f0 [PATCH] md: merge md_enter_safemode into md_check_recovery
md_enter_safemode checks if it is time to mark the md superblock as 'clean'.
i.e.  if all writes have completed and a suitable delay has passed.

This is currently called from md_handle_safemode which in-turn is called
(almost) every time md_check_recovery is called, and from the end of
md_do_sync which causes the mddev->thread to run, which will always call
md_check_recovery as well.

So it doesn't need to be a separate function and fits quite well into
md_check_recovery.

The "almost" is because multipathd calls md_check_recovery but not
md_handle_safemode.  This is OK because the code from md_enter_safemode is a
no-op if mddev->safemode == 0, which it always is for a multipathd (providing
we don't allow it to be set to 2 on a signal...)

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-21 19:07:42 -07:00
NeilBrown
7a5febe9ff [PATCH] md: set the unplug_fn and issue_flush_fn for md devices *after* committed to creation
We we set the too early, they may still be in place and possibly get called
even though the array didn't get set up properly.

Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-17 07:59:12 -07:00
Paul E. McKenney
fbd568a3e6 [PATCH] Change synchronize_kernel to _rcu and _sched
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.

Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-01 08:59:04 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00