udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When busy polling while a link is down (during a link-flap test), TX
timeouts were observed as well as the following messages in the ring
buffer:
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1
These were resolved by checking for link status and returning if link
was not up.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Rob Miller <rob.miller@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing that:
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0)
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0)
and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of
these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not
trigger.
Replace the bit test that overlap by an equality test, just as in
'bnxt_hwrm_tunnel_dst_port_free()' above.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
barrier() is a big hammer compared to READ_ONCE(),
and requires comments explaining what is protected.
READ_ONCE() is more precise and compiler should generate
better overall code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing synchronize_net() call to avoid potential use after free,
since we explicitly call napi_hash_del() to factorize the RCU grace
period.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer chips have proper support for 4-tuple UDP RSS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the speed setting on one port can affect the
available speed on the other port. Add logic to detect these changes
and adjust the advertised speed settings when necessary.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new FORCE_LINK_DWN bit to shutdown link during close.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.
Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced a typo making the driver no longer build, *sigh*.
Fixes: 42469bf5d9 ("net: bcm63xx_enet: Utilize phy_ethtool_nway_reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-flight DMA from 1st kernel could continue going in kdump kernel.
New io-page table has been created before bnx2 does reset at open stage.
We have to wait for the in-flight DMA to complete to avoid it look up
into the newly created io-page table at probe stage.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3e1be7ad2d.
When people build bnx2 driver into kernel, it will fail to detect
and load firmware because firmware is contained in initramfs and
initramfs has not been uncompressed yet during do_initcalls. So
revert commit 3e1be7a and work out a new way in the later patch.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the physical link is down and the VF virtual link is set to "enable",
the current code does not always work. If the link is down but the
cable is attached, the firmware returns LINK_SIGNAL instead of
NO_LINK. The current code is treating LINK_SIGNAL as link up.
The fix is to treat link as down when the link_status != LINK.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic is missing the check on whether the tx and rx rings are sharing
completion rings or not.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is automatically done from netif_napi_add(), and we want to not
export napi_hash_add() anymore in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.
This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.
Fixes: db791eb297 ("net: ethernet: bgmac: convert to feature flags")
Fixes: 4af1474e61 ("net: bgmac: Fix errant feature flag check")
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the variant of amac hardware present in the Broadcom
Northstar2 based SoCs. Northstar2 requires an additional register to be
configured with the port speed/duplexity (NICPM). This can be added to
the link callback to hide it from the instances that do not use this.
Also, clearing of the pending interrupts on init is required due to
observed issues on some platforms.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the bgmac driver to allow for phy's defined by the device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde1f ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d894be57ca92('ethernet: use net core MTU range checking in more drivers')
CC: Jarod Wilson <jarod@redhat.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time Sync (PTP) implementation uses the divisor/shift value for converting
the clock ticks to nanoseconds. Driver currently defines shift value as 1,
this results in the nanoseconds value to be calculated as half the actual
value. Hence the user application fails to synchronize the device clock
value with the PTP master device clock. Need to use the 'shift' value of 0.
Signed-off-by: Sony.Chacko <Sony.Chacko@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc found a reference to an uninitialized variable in the error handling
of bcm_enet_open, introduced by a recent cleanup:
drivers/net/ethernet/broadcom/bcm63xx_enet.c: In function 'bcm_enet_open'
drivers/net/ethernet/broadcom/bcm63xx_enet.c:1129:2: warning: 'phydev' may be used uninitialized in this function [-Wmaybe-uninitialized]
This makes the use of that variable conditional, so we only reference it
here after it has been used before. Unlike my normal patches, I have not
build-tested this one, as I don't currently have mips test in my
randconfig setup.
Fixes: 625eb8667d ("net: ethernet: broadcom: bcm63xx: use phydev from struct net_device")
Cc: Philippe Reynes <tremyfr@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions bnx2_reg_rd_ind(), bnx2_reg_wr_ind() and bnx2_ctx_wr()
can be called with IRQs disabled when netconsole is enabled. So they
should use spin_{,un}lock_irq{save,restore} instead of _bh variants.
Example call flow:
bnx2_poll()
->bnx2_poll_link()
->bnx2_phy_int()
->bnx2_set_remote_link()
->bnx2_shmem_rd()
->bnx2_reg_rd_ind()
-> spin_lock_bh(&bp->indirect_lock);
spin_unlock_bh(&bp->indirect_lock);
...
-> __local_bh_enable_ip
static inline void __local_bh_enable_ip(unsigned long ip)
WARN_ON_ONCE(in_irq() || irqs_disabled()); <<<<<< WARN
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the conversion to the feature flags, a check against
ci->id != BCMA_CHIP_ID_BCM47162
became
bgmac->feature_flags & BGMAC_FEAT_CLKCTLS
instead of
!(bgmac->feature_flags & BGMAC_FEAT_CLKCTLS)
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic #55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a063b1 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f37031 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The group list must be freed prior to freeing the command otherwise
we have a use-after-free.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6b352ebccb ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").
We needs to revert the commit 62469c7600 ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebccb ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for the pending list to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for 'mcast_list' to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:2763:5: warning: no previous prototype for 'bcmgenet_hfb_add_filter' [-Wmissing-prototypes]
In fact, this function is implemented in
drivers/net/ethernet/broadcom/genet/bcmgenet.c, but be called
by no one, thus can be removed.
So this patch removes the unused functions.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_hwrm_fw_set_time() now returns -EOPNOTSUPP when built for kernel
without RTC_LIB. Setting the firmware time is not critical to the
successful completion of the firmware update process.
Signed-off-by: Rob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
