Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace. This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.
Move over to the preferred way, that is, using compound pages instead. This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."
I fixed this by adding a check for zero. While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The first performs the simplex clearing relevant to some chipsets that
report simplex by default but can in fact do more if poked. The second
is used to strip DMA modes from a PCI control with no BAR4 allocation.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.
Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Encapsulate some of ata_scsi_slave_config so that parts
can be reused in future SAS patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch (and description) by Douglas Gilbert, with minor fixes
and API updates from me.
Changelog:
- make existing libata VPD device identification page (0x83)
supply the ATA serial number in the libata "vendor
specific" designator (from Chris Paulson-Ellis)
- add a "t10 vendor id based" designator as defined in
SAT rev 08 (section 10.3.4.2.3) that supplies ATA
model and serial numbers
- make the libata VPD page 0x83 more extensible (for
adding more designators in the future).
- rename EVPD to VPD in various places. Enable Vital
Product Data (EVPD) is a bit in the INQUIRY cdb.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
README: bzip2 is not new
Documentation/Changes: remove outdated translation references
remove dead Radeon URL
SCSI_AACRAID: add a help text
update the i386 defconfig
MAINTAINERS: remove the LANMEDIA entry
Move ip2.c and ip2main.c to drivers/char/ip2/ where the other files
Interrupt handler did not properly initialize a variable on a per-port
basis, leading to incorrect behavior on ports other than port 0.
Bug caught and fixed by Mark Lord.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most of the text by Mark Salyzyn <mark_salyzyn@adaptec.com>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
This allows the removal of the contained flag and also does a bit of
class renaming (sas_rphy->sas_device).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I think I promised to do this two years ago
This patch adds a scsi_disk class with the cache type and FUA
parameters, so user land application can easily obtain them without
having to parse dmesg. It also allows setting the cache type (use with
care...)
This patch is a bit dangerous because I've replaced the disk kref with a
class device reference ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move IDENTIFY info printing from ata_dev_read_id() to
ata_dev_configure() and print only if @print_info is non-zero. This
kills duplicate IDENTIFY info printing during probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dev->id is used many times in ata_dev_configure(). Use local variable
id instead for shorter notation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves the calling of target_destroy next to the list_del. This
closed a race being seen while doing a device add on the aic7xxx.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace the eh_timed_out method usage with setting sdev->timeout in
slave_configure. Also only use the extended timeout for raid volumes,
physical devices shouldn't need it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes expanders appear as labelled objects with properties in
the SAS tree.
I've also modified the phy code to make expander phys appear labelled by
host number, expander number and phy index.
So, for my current config, you see something like this in sysfs:
/sys/class/scsi_host/host1/device/phy-1:4/expander-1:0/phy-1-0:12/rphy-1:0-12/target1:0:1
And the expander properties are:
jejb@sparkweed> cd /sys/class/sas_expander/expander-1\:0/
jejb@sparkweed> for f in *; do echo -n $f ": "; cat $f; done
component_id : 29024
component_revision_id : 4
component_vendor_id : VITESSE
device : cat: device: Is a directory
level : 0
product_id : VSC7160 Eval Brd
product_rev : 4
uevent : cat: uevent: Permission denied
vendor_id : VITESSE
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves the eh_timed_out functionality from the scsi_host_template
to the transport_template. Given that this is now a transport function,
the EH_RESET_TIMER case no longer caps the timer reschedulings. The
transport guarantees that this is not an infinite condition.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Check bit 2 of Word 53 for Word 88 validity before using Word 88 to
determine UDMA mask. Note that the original xfer mask implementation
using ata_get_mode_mask() didn't consider bit 2 of Word 53. This
patch introduces different (correct) behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_probe() didn't set classes[] properly for port disabled case
of ->phy_reset() compatibility path. This patch moves classes[]
initialization and normalization out of ->probe_reset block such that
it applies to both ->probe_reset and ->phy_reset paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The variable was dereferenced only if it was NULL (sic)...
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted this NULL dereference.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add several missing messages from SPI3, SPI4 and SPI5:
- Terminate Process
- Continue Task
- Target Transfer Disable
- Clear ACA
- LUN Reset
- ACA
- QAS Request
Rename some older commands to their SPI5 names:
- Command Complete -> Task Complete
- Abort -> Abort Task Set
- Bus device Reset -> Target Reset
- Clear Queue -> Clear Task Set
Change spi_print_msg() to always consume one byte, even if we don't
recognise it. That allows drivers to call it in a loop to print all
messages.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ISP24XX FW does not support Mbx 0x74 ie Login Local Port.
Added the equivalent code for ISP24XX ie to relogin in non
fabric case for ISP24XX use login iocb.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Only support ZIO mode 6 on specific ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reserved-bit 15 must set when updating the swing/emphasis values.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Resync with latest NVRAM subsystem ID list.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As new 23xx firmware will accomidate ISP63xx types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Chip is similar in form to our ISP24xx offering.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the scsi_alloc_queue or the slave_alloc calls in scsi_alloc_device fail,
we forget to release the locally allocated sdev on the failure path.
Coverity #609
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's much, much more readable now.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Because of some quirk in the SCSI spec the aic79xx driver chose to
force a renegotiation when sending an inquiry. This should better
be handled by the upper layers if required at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the aic79xx driver to properly respond to BIOS
settings.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On certain systems the driver seems to hit upon some
"scsi0: Invalid Sequencer interrupt occurred." problem and dumps card state.
According to Adaptec engineers this message is harmless. So as not to
confuse user we can as well disable the internal card state dump and
just print out the message itself.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the error recovery. Routines for TARGET RESET
and ABORT COMMAND are split up as the logic is quite dissimilar.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch converts aic79xx to use the midlayer-supplied tcq
functions.
We also set the queuedepth to '1' if tcq is disabled; the
aic79xx driver gets confused otherwise. Will set it back to
'2' once I figure out how to queue requests in the driver.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes the need for platform_data->qfrozen.
We're now using complete() instead of semaphores thus
simplifying ahd_freeze_simq() quite a lot.
This also fixes some deadlocks in the recovery code (again).
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Two misc fixes:
- Fix deadlock caused by return with host_lock held in lpfc_findnode_did
- Initialize all fields of the allocated mail box structure to zero.
Was causing some sysfs mailbox commands to fail immediately after load.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce lpfc_reset_barrier() function for resets on dual channel adapters
Workaround for a hardware errata on dual channel asics. There is a
potential for the chip to lock up on a reset if a shared dma engine is in
use. The (ugly) work around requires a reset process which uses a mailbox
command to synchronize the independent channels prior to the reset to
avoid the issue. Unfortunately, the timing windows required to ensure this
workaround succeeds are very specific, meaning we can't release the cpu
during the barrier.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed a timer panic due to timer firing after freeing ndlp
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed RSCN handling when a PLOGI is in retry.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that change their NPortId on the fly
due to a cable swap.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Turn on AHCI_CMD_PREFETCH for PACKET commands. This hints the
controller that it can prefetch the CDB and the PRD entries. This
patch is originally from Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24 softreset timeout was > 100ms (100 loops with msleep(1)), which
turned out to be too short for some devices (ASI ARAID99 2000). This
patch converts sil24 softreset waiting loop to use proper timeout
condition and lengthen the timeout to ATA_TMOUT_BOOT secs and check
interval to 100ms. Chisato Yamauchi discovered the problem and
supplied initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Chisato Yamauchi <cyamauch@plamo.linet.gr.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil24 softreset routine used to check sata_dev_present() after
SRST is complete in the hope that SRST may do some good even when
SStatus reports no device. This is okay as long as SRST timeout is
short (> 100ms in the current code) but it seems that not all SATA
devices are happy with short SRST timeout.
This patch makes softreset exit early without performing actual SRST
if SStatus reports no device in preparation for lengthening SRST
timeout.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
