Also try to prevent some possible slave dereference race conditions. This is
finalized in the next patch, which abandons the slave array in favour of
a list_head list and list RCU.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the frame receive handler to hsr_slave.c.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_dev_xid is only used in ipconfig.c
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the connectable state change doesn't require any special HCI commands
the set_connectable_update_settings() function is used instead of the
set_connectable_complete() function. We must therefore make sure to call
hci_update_background_scan() there as well. This code path is used also
when we're powered off, but that's fine since hci_update_background_scan()
has the necessary checks for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The connectable and discoverable mgmt settings are supported both for LE
and BR/EDR controllers so they do not belong behind a lmp_bredr_capable()
condition. This patch fixes the issue in get_supported_settings().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If any of the HCI commands from the hci_stop_discovery function were
successfully sent we need to set the discovery state to STOPPING. The
Stop Discovery code was already handling this, but the code in
clean_up_hci_state was not. This patch updates the hci_stop_discovery to
return a bool to indicate whether it queued any commands and the
clean_up_hci_state() function respectively to look at the return value
and call hci_discovery_set_state() if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.
This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most controllers do not support advertising while initiating an LE
connection. We also have to first disable current advertising if the
initiation is going to happen through direct advertising. Therefore,
simply stop advertising as the first thing when starting to issue
commands to establish an LE connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When deciding to call disable_advertising() we're interested in the real
state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of
the HCI_ADVERTISING flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By adding support for disabling advertising when necessary and doing the
checks for existing LE connections inside the enable_advertising
function we can simplify the calling code quite a lot.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)
so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.
When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.
The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was triggered by these steps:
1) create socket, bind and then setsockopt for add mc group.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));
2) drop the mc group for this socket.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));
3) and then drop the socket, I found the mc group was still used by the dev:
netstat -g
Interface RefCnt Group
--------------- ------ ---------------------
eth2 1 255.0.0.37
Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:
The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.
v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
so I add the checking for the in_dev before polling the mc_list, make sure when
we remove the mc group, dec the refcnt to the real dev which was using the mc address.
The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug was introduced in NETDEV_CHANGE notifier sequence causing the
arp table to be sometimes spuriously cleared (including manual arp
entries marked permanent), upon network link carrier changes.
The changed argument for the notifier was applied only to a single
caller of NETDEV_CHANGE, missing among others netdev_state_change().
So upon net_carrier events induced by the network, which are
triggering a call to netdev_state_change(), arp_netdev_event() would
decide whether to clear or not arp cache based on random/junk stack
values (a kind of read buffer overflow).
Fixes: be9efd3653 ("net: pass changed flags along with NETDEV_CHANGE event")
Fixes: 6c8b4e3ff8 ("arp: flush arp cache on IFF_NOARP change")
Signed-off-by: Loic Prylli <loicp@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sw_hash flag to skbuff to indicate that skb->hash was computed
from flow_dissector. This flag is checked in skb_get_hash to avoid
repeatedly trying to compute the hash (ie. in the case that no L4 hash
can be computed).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically generate flow labels for IPv6 packets on transmit.
The flow label is computed based on skb_get_hash. The flow label will
only automatically be set when it is zero otherwise (i.e. flow label
manager hasn't set one). This supports the transmit side functionality
of RFC 6438.
Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior
system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this
functionality per socket.
By default, auto flowlabels are disabled to avoid possible conflicts
with flow label manager, however if this feature proves useful we
may want to enable it by default.
It should also be noted that FreeBSD has already implemented automatic
flow labels (including the sysctl and socket option). In FreeBSD,
automatic flow labels default to enabled.
Performance impact:
Running super_netperf with 200 flows for TCP_RR and UDP_RR for
IPv6. Note that in UDP case, __skb_get_hash will be called for
every packet with explains slight regression. In the TCP case
the hash is saved in the socket so there is no regression.
Automatic flow labels disabled:
TCP_RR:
86.53% CPU utilization
127/195/322 90/95/99% latencies
1.40498e+06 tps
UDP_RR:
90.70% CPU utilization
118/168/243 90/95/99% latencies
1.50309e+06 tps
Automatic flow labels enabled:
TCP_RR:
85.90% CPU utilization
128/199/337 90/95/99% latencies
1.40051e+06
UDP_RR
92.61% CPU utilization
115/164/236 90/95/99% latencies
1.4687e+06
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the receive side to support RFC 6438 which is to
use the flow label as an ECMP hash. If an IPv6 flow label is set
in a packet we can use this as input for computing an L4-hash. There
should be no need to parse any transport headers in this case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call standard function to get a packet hash instead of taking this from
skb->sk->sk_hash or only using skb->protocol.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a connected socket we can precompute the flow hash for setting
in skb->hash on output. This is a performance advantage over
calculating the skb->hash for every packet on the connection. The
computation is done using the common hash algorithm to be consistent
with computations done for packets of the connection in other states
where thers is no socket (e.g. time-wait, syn-recv, syn-cookies).
This patch adds sk_txhash to the sock structure. inet_set_txhash and
ip6_set_txhash functions are added which are called from points in
TCP and UDP where socket moves to established state.
skb_set_hash_from_sk is a function which sets skb->hash from the
sock txhash value. This is called in UDP and TCP transmit path when
transmitting within the context of a socket.
Tested: ran super_netperf with 200 TCP_RR streams over a vxlan
interface (in this case skb_get_hash called on every TX packet to
create a UDP source port).
Before fix:
95.02% CPU utilization
154/256/505 90/95/99% latencies
1.13042e+06 tps
Time in functions:
0.28% skb_flow_dissect
0.21% __skb_get_hash
After fix:
94.95% CPU utilization
156/254/485 90/95/99% latencies
1.15447e+06
Neither __skb_get_hash nor skb_flow_dissect appear in perf
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the hash computation located in __skb_get_hash to be a separate
function which takes flow_keys as input. This will allow flow hash
computation in other contexts where we only have addresses and ports.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the coding style issues reported by checkpatch.pl
following issues fixed:
CHECK: Alignment should match open parenthesis
WARNING: line over 80 characters
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: networking block comments don't use an empty /* line, use /* Comment...
WARNING: Missing a blank line after declarations
WARNING: networking block comments start with * on subsequent lines
CHECK: braces {} should be used on all arms of this statement
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the prototype of the do_one_broadcast() method so that it will return void.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link state acks triggered from the receive path is done before
the last received packet have been processed by the link layer.
The effect of this is that the last received packet will not be
included in the ack. This causes problems if the link window is
set to TIPC_MIN_LINK_WIN, where the ack interval will be equal to
the link tolerance, and the link enters a stop-and-go behavior.
We move the ack logic to after link state processing, just before
the packet is delivered to higher layers.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Carl Sigurjonsson <carl.sigurjonsson@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic change, separating message delivery from the
link state processing.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Open vSwitch
A set of fixes for net.
First bug is related flow-table management. Second one is in sample
action. Third is related flow stats and last one add gre-err handler for ovs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Always store in snt_synack the time at which the server received the
first client SYN and attempted to send the first SYNACK.
Recent commit aa27fc501 ("tcp: tcp_v[46]_conn_request: fix snt_synack
initialization") resolved an inconsistency between IPv4 and IPv6 in
the initialization of snt_synack. This commit brings back the idea
from 843f4a55e (tcp: use tcp_v4_send_synack on first SYN-ACK), which
was going for the original behavior of snt_synack from the commit
where it was added in 9ad7c049f0 ("tcp: RFC2988bis + taking RTT
sample from 3WHS for the passive open side") in v3.1.
In addition to being simpler (and probably a tiny bit faster),
unconditionally storing the time of the first SYNACK attempt has been
useful because it allows calculating a performance metric quantifying
how long it took to establish a passive TCP connection.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Jerry Chu <hkchu@google.com>
Acked-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In process_backlog the input_pkt_queue is only checked once for new
packets and quota is artificially reduced to reflect precisely the
number of packets on the input_pkt_queue so that the loop exits
appropriately.
This patches changes the behavior to be more straightforward and
less convoluted. Packets are processed until either the quota
is met or there are no more packets to process.
This patch seems to provide a small, but noticeable performance
improvement. The performance improvement is a result of staying
in the process_backlog loop longer which can reduce number of IPI's.
Performance data using super_netperf TCP_RR with 200 flows:
Before fix:
88.06% CPU utilization
125/190/309 90/95/99% latencies
1.46808e+06 tps
1145382 intrs.sec.
With fix:
87.73% CPU utilization
122/183/296 90/95/99% latencies
1.4921e+06 tps
1021674.30 intrs./sec.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.
Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008e1 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.
When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.
One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.
All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.
Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.
Fixes: 46517008e1 ("ipv4: Kill ip_rt_frag_needed().")
Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows applications to enable hardware timestamping without being aware
of it being a vlan device and figuring out the real device.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace two switch statements enumerating all valid ptp classes with an if
statement matching for not PTP_CLASS_NONE.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For adapters that do not support LE and ones where LE hasn't been
enabled we shouldn't be trying to initiate background scanning. This
patch adds an extra check to the hci_update_background_scan() to ensure
that we bail out if HCI_LE_ENABLED is not set.
Since we do allow user space to feed the kernel with LE connection
parameters even when LE is not enabled we now need to also call
hci_update_background_scan() as soon as LE gets enabled so that scanning
gets started if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enabling passive scanning always when we're connectable aligns us with
the BR/EDR page scanning. This is also consistent with the fact that the
code dealing with passive scanning results will actively try to connect
any direct advertising event when we're connectable.
This patch implements the feature by adding the connectable condition to
hci_update_background_scan() checks for starting scanning and by calling
hci_update_background_scan() whenever the connectable state changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have an active discovery going on we shouldn't do any changes to
LE scanning when hci_update_background_scan() is called (a call which
can happen for many different reasons). This patch fixes the issue by
returning from the function if the discovery state is anything else
except DISCOVERY_STOPPED.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In a subsequent patch the hci_update_background_scan() function will
depend on being able to know the current discovery state. For this to be
possible we need to set the new state early in the function. Since we
also need to check what the old state was this patch introduces an extra
variable for tracking it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the only caller of this function doesn't care about the return
value anymore let's just remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have the process_adv_report() function doing the IRK lookup
and updating the bdaddr we don't need to do this anymore in mgmt.c in
the mgmt_device_found() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have devices set as to be connected we should connect to them even
during normal discovery if we get a connectable advertising event. If we
also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events
even to devices that we don't have in our pend_le_conns list. This patch
implements such behavior by passing the advertising report type to
check_pending_le_conn() and calls that function regardless of what type
of scanning we are doing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hdev->send driver callback is mandatory to be provided by a driver
before calling hci_register_dev. So enforce it and return EINVAL in
case it is not available.
All existing drivers are providing this callback anyway, so this is
just an extra sanity check.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The drivers are allowed to just return an error from hdev->send callback
and in that case the driver does not own the SKB. Which means that the
caller has to free the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When we get an LE connection complete event we should restart background
scanning if there are any devices needing it. So far the code was only
making the decision based on whether the completed connection had any
stored parameters or not. This patch ensures that we trigger background
scanning always when necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the driver sets HCI_QUIRK_RAW_DEVICE, the controller will be set
as unconfigured. However running the unconfigured init procecure is
not useful since raw-only devices are not allowed to change its
configuration. This change skips the init procedure and just allows
user channel operation for this device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an unconfigured controllers reaches the configured state, it is
important to change the HCI_RAW flag. It indicates to userspace that
the controller is fully operational.
External configuration allows to bring the controller back into an
unconfigured state. In that case make sure HCI_RAW flag is set again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for changing the public device address. This feature
is required by controllers that do not provide a public address and
have HCI_QUIRK_INVALID_BDADDR set.
Even if a controller has a public device address, this is useful when
an embedded system wants to use its own value. As long as the driver
provides the set_bdaddr callback, this allows changing the device
address before powering on the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.
This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BR/EDR has the connection request and connection request rejection, but
LE doesn't have anything similar. We still request LE connections to
blocked devices to be disconnected but it's possible that ACL data slips
through before that. The check in l2cap_recv_frame really only needs to
be for LE and not BR/EDR because of this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For an unconfigured controller it is required to read at least the
local version information. If the set_bdaddr driver callback is
provideded, then also the local Bluetooth address will be read.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI event callbacks have grown over the last years and some
functions handle status checking different than others. For the
simple ones, check the status at the beginning and exit if an
error with the HCI command occured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When one or more of the missing configuration options change, then send
this even to all the other management interface clients.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move the mgmt_event function higher up in the code so that no forward
declaration is needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set External Configuration management command allows for switching
between configured and unconfigured start if HCI_QURIK_EXTERNAL_CONFIG
is set by the transport driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the quirks that are allow to be set during setup callback, the
check needs to be modified so that they are applied even if no
setup callback provided by the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reading the controller configuration information is a valid management
command when the controller is unconfigured. Allow this command, but
return invalid index on all other commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's wasteful to use list_del_init (which re-initializes the list_head)
if we're just about to free the element and never use it again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_conn_params_set() is called if the new auto_connect value is
the same as the old one we don't need to take any action. Simply return
success from the function in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that pend_le_connections is a list of hci_conn_params entries we can
simply remove items from that list as we iterate through the global list
of le_conn_params. This also moves the responsibility of calling
hci_update_background_scan() to the functions that were previously
calling hci_pend_le_conns_clear(). The only user that's left for
hci_pend_le_conns_clear() is hci_dev_do_close() which anyway does not
need to call hci_update_background_scan().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a device is in the pend_le_conns list it cannot at the same time also
have the need to be notified through mgmt_device_found. By making
check_pending_le_conn return whether it found an entry or not we can
avoid unnecessary checks in process_adv_report().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing passive scanning results we need the resolved identity
address both in check_pending_le_conn() as well as later in
process_adv_report(). Since process_adv_report() calls
check_pending_le_conn() we can simply resolve the IRK earlier in the
function and thereby eliminate a second lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling Remove Device for an entry using HCI_AUTO_CONN_REPORT we
need to decrement the pend_le_reports value correspondingly. This patch
fixes one such missing action in the Remove Device command handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The handler for variable length commands were trying to calculate the
expected length of the command based on the given parameter count, and
then comparing that with the received data. However, the expected count
was stored in a u16 which can easily overflow. With a carefully crafted
command this can then be made to match the given data even though the
parameter count is actually way too big, resulting in a buffer overflow
when parsing the parameters.
This patch fixes the issue by calculating a per-command maximum
parameter count and returns INVALID_PARAMS if it is exceeded.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're scanning for specific devices that use an RPA we need to
convert the RPA to the identity address before looking up the entry in
the connection parameters. This patch adds the necessary code to do this
in the process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the kernel is doing LE scanning because of one or more devices
added with action 0x00 through the Add Device command we do want to let
mgmt_device_found() to proceed with sending an event. This kind of
devices are tracked with hdev->pend_le_reports, so check this value
before bailing out from the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.
The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we don't have an identity address for connection parameters it
doesn't really make sense to send them to user space. Instead just
ignore them for now. Later we can add support for sending them when we
eventually get the identity through pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are more places that can take advantage of is_identity_address()
besides hci_core.c. This patch moves the function to hci_core.h and
gives it the appropriate hci_ prefix.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The caller of hci_le_conn_update is directly interested in knowing what
the best value is for the store_hint parameter of the corresponding
mgmt event. Since hci_le_conn_update knows whether there were stored
parameters that were updated or not we can have it return an initial
store_hint value to the caller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should update any stored connection parameters when we receive the LE
Remote Connection Parameter Request HCI event. This patch adds the
necessary code to the function that handles the event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the new Load Connection Parameters mgmt command
that's intended to load the desired connection parameters for LE
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Remove Device mgmt command is supposed to undo what the Add Device
command does. An entry added by Add Device cannot have the
HCI_AUTO_CONN_DISABLED auto_connect value, so we should treat this as an
invalid entry to remove. This patch adds the necessary pieces to the
Remove Device command handler so that it only removes entries which were
added by Add Device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we'll need to either clear only the enabled
parameters or only the disabled ones. This patch adds convenience
functions for this purpose.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When allocating a new controller structure, then default to the internal
use value 0xffff first. Default to 0x0000 is a bad idea since that is
the manufacturer identifier of Ericsson Technology Licensing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Unlike BR/EDR we cannot reject LE connections of blocked devices but
have to do it as soon as we get a LE Connection Complete event. The
patch adds a blacklist check to the hci_le_conn_complete_evt function
and drops all connections for blocked devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ATT channel isn't the only one that we should ensure doesn't receive
data from blocked devices. SMP is another, and in general we don't want
data packets going to any of the various handlers. Therefore, add a
single check to the l2cap_recv_frame function.
The patch fixes at the same time the use of a correct address type. The
blacklist stores the values with the user space facing triple type
wheras hci_conn->dst_type uses the HCI address type (0x00 or 0x01).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some embedded controllers allow the programming of a public address
and this adds vendor support for supporting OEM confguration of such
addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth 4.1 introduces a new LE meta event called "LE Remote
Connection Parameter Request" event. In order to the controller
sends this event to host, we should enable it during controller
initialization.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During init2 phase, the LE local features have not be read yet so
we aren't able to rely on hdev->le_features to determine if the
controller supports the Connection Parameters Request Procedure.
For that reason, this patch moves LE event mask setting from init2
into init3 initialization phase.
The hdev->le_features mask will be checked by the next patch in order
to know if "LE Remote Connection Parameter Request Event" should be
enabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.
Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.
We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.
The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The background scanning normally gets enabled during power on by
adding devices to the pending connection list. However devices
might be already on that list and the list of devices is empty,
then it is better to trigger the background manually.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a new controller is initialized, but not powered from userspace
at the moment, the HCI_AUTO_OFF flag is still set. During this period,
userspace might program device for auto-connection, but never power
on the controller. In this case do not try to start background
scanning and leave it for later to be started.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we're encrypted with the STK we should allow re-encryption with an
LTK even though the achieved security level is the same. This patch adds
the necessary logic to the smp_sufficient_security function which is
used to determine whether to proceed with encryption or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're already encrypted with a good enough LTK we should just ignore
an incoming SMP Security Request. The code was already taking care of
this in the smp_conn_security function before calling smp_ltk_encrypt
but failed to do the same in smp_cmd_security_req. This patch fixes the
issue by moving up the smp_sufficient_security function and using it in
the Security Request handler before trying to request encryption.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The advertising data and scan response data are merged in the wrong
order. It should be advertsing data first and then scan response data
and not the other way around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.16
The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_conn_params_add function provides the default allocation of
connection parameters. To avoid code duplication, use that code from
hci_conn_params_set to allocate or lookup parameter struct.
As a benefit the connection latency and supervision timeout parameters
are no longer reset to default when calling hci_conn_params_set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding new connection parameters, it is useful to return either
the existing struct or the newly created one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of smp_ltk_encrypt is simple boolean, so just use
bool and make the code a bit more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is to support the Motorola HF850 carkit which reports the error
code 0x10 for an eSCO attempt, even though it advertises eSCO support.
With this patch we will retry with a SCO connection, which succeeds.
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Kiran Kumar Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have all the necessary remote information for getpeername() when we
are in the BT_CONFIG state so this should be allowed. This is
particularly important for LE sockets where changing the security level
will temporarily move the socket into BT_CONFIG state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bt_seq_ops is only used with __seq_open_private as
const struct seq_operations *
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames l2cap_check_conn_param() to hci_check_conn_params()
and moves it to hci_core.h so it can reused in others files. This helper
will be reused in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller is not active or in init/setup phase, do not
try to start or stop background scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When trying to pair a new Bluetooth Low Energy device, then make sure
that the default connections parameters are in place before trying to
establish the first connection to that device. With the connection
parameters structure allocated, the slave preferred values can now
easily be tracked and all future connections will use the correct
values from that start decreasing connection establishment time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases it is useful to not overwrite connection parametes and
instead just create default ones if they don't exist. This function
does exactly that. hci_conn_params_add will allow to create new
default connection parameters. hci_conn_params_set will set the
values and also create new parameters if they don't exist.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the supervision timeout. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the connection latency. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Store the connection latency and supervision timeout default values
with all the other controller defaults. And when needed use them
for new connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When devices are added or removed, then make sure that events are send
out to all other clients so that the list of devices can be easily
tracked. This is especially important when external clients are
adding or removing devices within the auto-connection list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the auto-connection handling has gained offical management
command support, remove the le_auto_conn debugfs entry.
For debugging purposes replace it a simple device_list debugfs
entry that allows listing of the current internal auto-connection
list used for passive scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows adding or removing devices from the background scanning
list the kernel maintains. Device flagged for auto-connection will
be automatically connected if they are found.
The passive scanning required for auto-connection will be started
and stopped on demand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the LE connection parameters for connection latency and
supervision timeout are known, then use then. If they are not
know fallback to defaults.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the slave updates the connection parameters, store also the
connection latency and supervision timeout information in the
internal list of connection parameters for known devices.
Having these values available allowes the auto-connection
procedure to use the correct values from the beginning without
having to request an update on every connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling hci_conn_params_clear function, it should update the
background scanning properly and not require a separate call to
update it.
For the case when the function is used during unregister of a
controller, an extra safe guard is but in place.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When hci_conn_params_clear is called, it is always followed by a
call to hci_pend_le_conns_clear. So instead of making this explicit
just make sure it is always called. This makes this function similar
on how hci_conn_params_add and hci_conn_params_del work.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_pend_le_conn_* function should be placed before their actual
users. So move them before hci_conn_params_* functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of non-resovlable private addresses for passive scanning is
a bad idea. Passive scanning will not send any SCAN_REQ and thus using
your identity address for passive scanning is not a privacy issue.
It is important to use the identity address during passive scanning
since that is the only way devices using direct advertising will be
reported correctly by the controller. This is overlooked detail in
the Bluetooth specification that current controllers are not able
to report direct advertising events for other than their current
address.
When remote peers are using direct advertising and scanning is done
with non-resolvable private address these devices will not be found.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
