OpenBlocks A6 has three leds via GPIO. This supports them.
And this fix typo about led, because hardware manual has typo.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OpenBlocks A6 uses second I2C with RTC of s35390a.
This supports them.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Second I2C bus is supported by 88f6282 and 88f6283.
This creates kirkwood-6282.dtsi, and defines DT table
of second I2C bus.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a couple of different variants of Kirkwood, which differ in
the pin muxing. These DTSI files set the correct compatibility and
define commonly used groups of pins, which board dbs files can
reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the ongoing conversion of Orion SoCs to DT, make use of
gpio and pinctrl drivers through DT. The main dtsi for Dove is prepared
to allow board specific descriptors to make use of pinctrl muxing.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB and HDD using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to SATA0 and SATA1 using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Also enable the gpio-poweroff driver when DT is used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The default chip-delay of 25us is a bit too tight for some DNS-320's,
and D-Link seem to specify 30us in their kernels for both devices.
Increase to 35us to make sure the NAND is stable.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit converts the 'LaCie Ethernet Disk mini v2' board to the
Device Tree. All devices that have existing Device Tree bindings are
converted over to the Device Tree, the other devices remain
instantiated in the old way, until the respective drivers get the
needed Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds basic DT support for the Orion5x SoC family. It adds
an orion5x.dtsi description of the Orion5x SoC as well as the needed
DT_MACHINE structure to support boards converted to DT in the future.
So far, the Device Tree contains the interrupt controller, the GPIO
bank, the UART controllers, the SPI controller, the watchdog, the SATA
controller, the I2C controller and the cryptographic engine.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Hello, Andrew
> > +#define NSA310_GPIO_LED_ESATA_GREEN 12
> > <..>
> > +#define NSA310_GPIO_POWER_OFF 48
>
> It looks like most of these are not used. Please remove them.
True. Fixed.
> > +static struct mtd_partition nsa310_mtd_parts[] = {
> > + {
> > + .name = "uboot",
> > + .offset = 0,
> > + .size = 0x100000,
> > + .mask_flags = MTD_WRITEABLE,
> > + }, {
> > <..>
> You should be able to put all that into DT. Take a look at
Correct. I did the conversion and tested that the partitions
can be read with dd and produce exactly the same data before and
after conversion. So, the partition offsets at least should be fine.
> > +static struct i2c_board_info __initdata nsa310_i2c_info[] = {
> > + { I2C_BOARD_INFO("adt7476", 0x2e) },
> > +};
>
> You can also do this in DT as well. kirkwood-ts219.dtsi has
>
> i2c@11000 {
> status = "okay";
> clock-frequency = <400000>;
Ok, I did convert the i2c definition to use the devicetree.
The adt7476 device itself is not at reach of device tree,
AFAIK and requires more work at there?
Thanks for your valuable comments. Following is a new patch that
should address the problems and mistakes you pointed and also
some of the pointed by Jason Cooper. The nand and i2c are now
defined at DT and I also removed the pointless defines and
ARM_APPENDED_DTB. It is based against the Linus' official
3.6 version.
Best regards,
Tero
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a new kirkwood box made by Universal Scientific Industrial, Inc.
The product description is here:
http://www.usish.com/english/products_topkick1281p2.php
It is very similar to the dreamplug and other plug devices, with the
exception that it has room for a 2.5" SATA HDD internally.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Remove board specific gpio-fan driver registration. Moved into device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since commit edc88ceb0 (ARM: be really quiet when building with 'make -s') the
following output is generated when building a kernel for ARM:
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
Building modules, stage 2.
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
As per Documentation/kbuild/makefiles.txt the correct way of using kecho is
'@$(kecho)'.
Make this change so no more unwanted 'echo' messages are displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The reg property contains <base length> not <base last_offset>. Fix
the length values to be length not last_offset.
Cc: stable@vger.kernel.org
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
From Kukjin Kim <kgene.kim@samsung.com>:
One is spi stuff for fix the device names for the different subtypes of
the spi controller. And the other is adding missing .smp field for
exynos4-dt and fixing memory sections for exynos4210-trats board.
* 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set .smp field of machine descriptor for exynos4-dt
ARM: dts: Split memory into 4 sections for exynos4210-trats
ARM: SAMSUNG: Add naming of s3c64xx-spi devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
mux and pinctrl fixes, and Beagle OPP fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GIXH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc2/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Timer fix for am33xx, runtime PM fix for UART, audio McBSP fixes,
mux and pinctrl fixes, and Beagle OPP fix.
* tag 'omap-for-v3.7-rc2/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
ARM: OMAP3: Beagle: fix OPP customization and initcall ordering
ARM: OMAP3: Fix 3430 legacy mux names for ssi1 signals.
ARM: OMAP2+: Fix location of select PINCTRL
ARM/dts: omap3: Fix mcbsp2/3 hwmods to be able to probe the drivers for audio
ARM: OMAP2: UART: fix console UART mismatched runtime PM status
ARM: OMAP3: PM: apply part of the erratum i582 workaround
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The most important ones are a duplicated definition of a Kconfig
variable and the handling of external interrupts for non-DT case.
The new at91sam9g10 was suffering a recognition issue due to an ID
mis-interpreted: this was leading to a kernel panic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQiPCWAAoJEAf03oE53VmQHZcH/2cAmpXeCoLwtpmRs0WpumtN
OnIVB0W4EchnCUSfd19q4FiUANfPFAxRN0yxx8Sby4wUMUMKnAu6eLebhumeBl6i
L/80KDwIUOhxXCt8YV9tjH1sGDddiG8oQWLF9wfKTIAyTNKcG3usuxq/bTooiXnE
8i1dYvM0w9A7vseYDOOzDgapslStJUBaaZllNddhyP/FyGJZopGb6ObhI1PLeyTJ
iRLA5+NeFAdHIV7y875JlIWacfzQxEa0u2cptVAz9ZmYobesTZJkhzGAjpFEwUB1
bGktll0opy+2pPg8JFqZLC/qdYzVZJxSBWbT/zA2amf8asN4NFReTxHnsh81Rfs=
=AgpJ
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
A mix of typos and critical fixes.
The most important ones are a duplicated definition of a Kconfig
variable and the handling of external interrupts for non-DT case.
The new at91sam9g10 was suffering a recognition issue due to an ID
mis-interpreted: this was leading to a kernel panic.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91: (257 commits)
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current DT nodes for mx23/mx28 miss the `clocks-names` item for gpmi-nand.
So the gpmi-nand driver could not find the proper clock.
This patch fixes this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now the Nomadik I2C driver has been converted to an AMBA one, we
are required to provide the Primecell IDs via platform code. When
booting with DT enabled these have to be specified in the device
nodes. We do that here.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
