This adds logic to the MMC core to set VQMMC. This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.
A few notes:
* When setting the signal voltage to 3.3V we do our best to make VQMMC
and VMMC match. It's been reported that this makes some old cards
happy since they were tested back in the day before UHS when VQMMC
and VMMC were provided by the same regulator. A nice side effect of
this is that we don't end up on the hairy edge of VQMMC (2.7V),
which some EEs claim is a little too close to the minimum for
comfort.
This is done in two steps. At first we try to find a VQMMC within
a 0.3V tolerance of VMMC and if this is not supported by the
supplying regulator we try to find a suitable voltage within the
whole 2.7V-3.6V area of the spec.
* The two step approach is currently necessary, as the used
regulator_set_voltage_triplet(min, target, max) uses a simple
implementation that just tries two basic steps:
regulator_set_voltage(target, max);
regulator_set_voltage(min, target);
So with only one step with 2.7-3.6V borders, if a suitable voltage
is a bit below VMMC, we would directly get the lowest 2.7V
which some boards (like Rockchips) don't like at all.
* When setting the signal voltage to 1.8V or 1.2V we aim for that
specific voltage instead of picking the lowest one in the range.
* We very purposely don't print errors in mmc_regulator_set_vqmmc().
There are cases where the MMC core will try several different
voltages and we don't want to pollute the logs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will shortly need the calculation of an ocr-bit to the actual
voltage in a second place too, so move it from mmc_regulator_set_ocr
to a common function mmc_ocrbitnum_to_vdd to make that possible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25
for mmc_ios_show to show the ios->timing if mmc card runs under
these two modes.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi chips will not work properly if we try to start new
sdio-rw requests while the device is signalling that it is busy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a helper function to check if an opcode is a sd-io-rw-* opcode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The simple power sequence provider sets a value for multiple GPIOs in one
go so it is better to use the API already provided by the GPIO descriptor
API instead of open coding the same logic.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add ios->drv_type for mmc_ios_show to show the
card's driver type.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The gpiod_get() function expands to gpiod_get_index() with index 0
so it's better to use it since is easier to read and more concise.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.
Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Fixes: 16b23787fc ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[ 20.740134] c0 3136 (Compiler) Call trace:
[ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
//
// If CPU0 has just finished "is_done_rcv = true" in path1, and at
// this moment, IRQ or ICache line missing happens in CPU0.
// What happens in CPU1 (path2)?
//
// If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
// path2 would have chance to break from wait_event_interruptible
// in mmc_wait_for_data_req_done and continue to run for next
// mmc_request (mmc_blk_rw_rq_prep).
//
// Within mmc_blk_rq_prep, mrq is cleared to 0.
// If below line still gets host from "mrq" as the result of
// compiler, the panic happens as we traced.
wake_up_interruptible(&mrq->host->context_info.wait);
}
path2: CPU1: <The mmcqd thread runs mmc_queue_thread>
static int mmc_wait_for_data_req_done(...
{
...
while (1) {
wait_event_interruptible(context_info->wait,
(context_info->is_done_rcv ||
context_info->is_new_req));
static void mmc_blk_rw_rq_prep(...
{
...
memset(brq, 0, sizeof(struct mmc_blk_request));
This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
+ mdelay(1);
wake_up_interruptible(&mrq->host->context_info.wait);
}
At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).
This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 2220eedfd7 ("mmc: fix async request mechanism ....")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use more compact of_property_read_bool() calls instead of the
of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When requesting a trim for several bytes, everything up to the next
erase-group is erased. This causes data corruption.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Other subsystem buses attach PM domains during probe, but prior calling
the driver's ->probe() method. During the removal phase, detaching the PM
domain will be done after invoking the driver's ->remove() callback.
Convert the SDIO bus to follow this behavior and add error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.
Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
IO state variable drv_type could be set during card
initialization. Consequently, it must be reset to the
default value when setting the initial state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the regulator used for the SDMMC IO voltage is not expected to
draw a lot of current, most systems will probably use an inexpensive
LDO for it. LDO regulators apparently have the feature that they
don't actively drive the voltage down--they wait for other components
in the system to drag the voltage down. Thus they will transition
faster under heavy loads and slower under light loads.
During an SDMMC voltage change from 3.3V to 1.8V, we are almost
certainly under a light load. To be specific:
* The regulator is hooked through pulls to CMD0-3 and DAT. Probably
the CMD pulls are something like 47K and the DAT is something like
10K.
* The card is supposed to be driving DAT0-3 low during voltage change
which will draw _some_ current, but not a lot.
* The regulator is also provided to the SDMMC host controller, but the
SDMMC host controller is in open drain mode during the voltage
change and so shouldn't be drawing much current.
In order to keep the SDMMC host working properly (or for noise
reasons), there might also be a capacitor attached to the SDMMC IO
regulator. This also will have the effect of slowing down transitions
of the regulator, especially under light loads.
From experimental evidence, we've seen the voltage change fail if the
card doesn't detect that the voltage fell to less than about 2.3V when
we turn on the clock. On one device (that admittedly had a 47K CMD
pullup instead of a 10K CMD pullup) we saw that the voltage was just
about 2.3V after 5ms and thus the voltage change would sometimes fail.
Doubling the delay gave margin and made the voltage change work 100%
of the time, despite the slightly weaker CMD pull.
At the moment submitting this as an RFC patch since my problem _could_
be fixed by increasing the pull strength (or using a smaller
capacitor). However being a little bit more lenient to strange
hardware could also be a good thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
card->ext_csd.enhanced_area_offset is defined as "unsigned long long",
and, ext_csd[] is defined as u8.
unsigned long long data might have strange data if first bit of ext_csd[]
was 1. this patch cast it to (unsigned long long)
Special thanks to coverity <http://www.coverity.com>
ex)
u8 data8;
u64 data64;
data8 = 0x80;
data64 = (data8 << 24); // 0xffffffff80000000
data64 = (((unsigned long long)data8) << 24); // 0x80000000;
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not uncommon to see systems where there is no physical write-protect
signal (e.g. when using eMMC or microSD card slots). For some controllers,
which have a dedicated write-protection detection logic (like SDHCI
controllers), the get_ro() callback can return bogus data in such a case.
Instead of handling this on a per controller basis this patch adds a new
capability flag to the MMC core that can be set to specify that the result
of get_ro() is invalid. When the flag is set the core will not call
get_ro() and assume that the card is always read-write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Check the error code for EOPNOTSUPP and do not print
reset warning in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CRC errors could possibly be alleviated by
re-tuning so flag re-tuning needed in those cases.
Note this has no effect if re-tuning has not been
enabled.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HS400 re-tuning must be done in HS200 mode. Add
the ability to switch from HS400 mode to HS200
mode before re-tuning and switch back to HS400
after re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make a separate function to do the mmc_switch status check
so it can be re-used. This is preparation for adding support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sleep command is issued after deselecting the
card, but re-tuning won't work on a deselected card
so re-tuning must be held.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hold re-tuning during bkops to prevent
it from conflicting with the busy state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hold re-tuning during erase commands to prevent
it from conflicting with the sequence of commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hold re-tuning during switch commands to prevent
it from conflicting with the busy state or the CMD13
verification.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the start of each request, re-tune if needed and
then hold off re-tuning again until the request is done.
Note that though there is one function that starts
requests (mmc_start_request) there are two that wait for
the request to be done (mmc_wait_for_req_done and
mmc_wait_for_data_req_done). Also note that
mmc_wait_for_data_req_done can return even when the
request is not done (which allows the block driver
to prepare a newly arrived request while still
waiting for the previous request).
This patch ensures re-tuning is held for the duration
of a request. Subsequent patches will also hold
re-tuning at other times when it might cause a
conflict.
In addition, possibly a command is failing because
re-tuning is needed. Use mmc_retune_recheck() to check
re-tuning. At that point re-tuning is held, at least by
the request, so mmc_retune_recheck() flags host->retune_now
if the hold count is 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable re-tuning when tuning is executed and
disable re-tuning when card is no longer initialized.
In the case of SDIO suspend, the card can keep power.
In that case, re-tuning need not be disabled, but, if
a re-tuning timer is being used, ensure it is disabled
and assume that re-tuning will be needed upon resume
since it is not known how long the suspend will last.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, there is core support for tuning during
initialization. There can also be a need to re-tune
periodically (e.g. sdhci) or to re-tune after the
host controller is powered off (e.g. after PM
runtime suspend / resume) or to re-tune in response
to CRC errors.
The main requirements for re-tuning are:
- ability to enable / disable re-tuning
- ability to flag that re-tuning is needed
- ability to re-tune before any request
- ability to hold off re-tuning if the card is busy
- ability to hold off re-tuning if re-tuning is in
progress
- ability to run a re-tuning timer
To support those requirements 7 members are added to struct
mmc_host:
unsigned int can_retune:1; /* re-tuning can be used */
unsigned int doing_retune:1; /* re-tuning in progress */
unsigned int retune_now:1; /* do re-tuning at next req */
int need_retune; /* re-tuning is needed */
int hold_retune; /* hold off re-tuning */
unsigned int retune_period; /* re-tuning period in secs */
struct timer_list retune_timer; /* for periodic re-tuning */
need_retune is an integer so it can be set without needing
synchronization. hold_retune is a integer to allow nesting.
Various simple functions are provided to set / clear those
variables.
Subsequent patches take those functions into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some drivers schedule automatic hw resets. An example is mwifiex,
which schedules a card reset if the command handler between driver
and card firmware becomes out of sync
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(),
as result mmc_rescan() could be scheduled and executed at
late hibernation restore stages when MMC device is suspended
already - which, in turn, will lead to system crash on TI dra7-evm board:
WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access
Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify().
Fixes: 4c2ef25fe0 (mmc: fix all hangs related to mmc/sd card...)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 6685ac62b2 ("mmc: core: Convert mmc_driver to
device_driver")
The reverted commit went too far in simplifing the device driver parts
for mmc.
Let's restore the old mmc_driver to enable driver core to sooner
or later to remove the ->probe(), ->remove() and ->shutdown() callbacks
from the struct device_driver.
Note that, the old ->suspend|resume() callbacks in the struct
mmc_driver don't need to be restored, since the mmc block layer has
converted to the modern system PM ops.
Fixes: 6685ac62b2 ("mmc: core: Convert mmc_driver to device_driver")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
If the struct mmc_pwrseq_match .alloc function used to allocate a
struct mmc_pwrseq fails, the error is propagated to mmc_of_parse().
But instead of returning the error code in pwrseq, host->pwrseq is
returned which will always be 0. So mmc_of_parse() succeeds even if
the pwrseq .alloc function failed and host->pwrseq is NULL.
This makes the SDIO device to not be powered if the power sequencing
.alloc functions wants to be deferred due a missing resource because
the mmc controller driver probe did wrongly succeed.
Fixes: 0f12a0ce4c ("mmc: pwrseq: simplify alloc/free hooks")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:
mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_HPI_MGMT, 1,
card->ext_csd.generic_cmd6_time);
There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently those host drivers which have deployed runtime PM, deals with
the runtime PM reference counting entirely by themselves.
Since host drivers don't know when the core will send the next request
through some of the host_ops callbacks, they need to handle runtime PM
get/put between each an every request.
In quite many cases this has some negative effects, since it leads to a
high frequency of scheduled runtime PM suspend operations. That due to
the runtime PM reference count will normally reach zero in-between
every request.
We can decrease that frequency, by enabling the core to deal with
runtime PM reference counting of the host device. Since the core often
knows that it will send a seqeunce of requests, it makes sense for it
to keep a runtime PM reference count during these periods.
More exactly, let's increase the runtime PM reference count by invoking
pm_runtime_get_sync() from __mmc_claim_host(). Restore that action by
invoking pm_runtime_mark_last_busy() and pm_runtime_put_autosuspend()
in mmc_release_host(). In this way a runtime PM reference count will be
kept during the complete cycle of a claim -> release host.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Konstantin Dorfman <kdorfman@codeaurora.org>
These callbacks have been set to deprecated for some time. The last
user (omap_hsmmc) has moved away from using them, which thus enables
us to completely remove them.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().
To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The alloc() and free() hooks required each pwrseq implementation to set
host->pwrseq themselves. This is error-prone and could be done at a
higher level if alloc() was changed to return a pointer to a struct
mmc_pwrseq instead of an error code.
This patch performs this change and moves the burden of maintaining
host->pwrseq from the power sequence hooks to the pwrseq code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f4833
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
This patch provides a simple mmc-pwrseq-emmc driver, which controls
single gpio line. It perform standard eMMC hw reset procedure, as
descibed by Jedec 4.4 specification. This procedure is performed just
after MMC core enabled power to the given mmc host (to fix possible
issues if bootloader has left eMMC card in initialized or unknown
state), and before performing complete system reboot (also in case of
emergency reboot call). The latter is needed on boards, which doesn't
have hardware reset logic connected to emmc card and (limited or broken)
ROM bootloaders are unable to read second stage from the emmc card if
the card is left in unknown or already initialized state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host drivers have different ways to sends their "init stream" to the
card. Some need to do it as part of a request, some do it from the
->set_ios() callback in the MMC_POWER_ON state and some don't send an
"init stream" at all.
To be able to use the reset GPIOs from the simple MMC power sequence
provider, the card need to be powered and the "init stream" must not
have been sent.
To cope with these requirements, invoke mmc_pwrseq_post_power_on()
prior we change the state to MMC_POWER_ON in mmc_power_up().
Host drivers shall perform power up operations in the MMC_POWER_UP
state. Unfortunate three hosts (au1xmmc, cb710-mmc and toshsd) don't
conform to this expectation. Instead those ignore the MMC_POWER_UP
state and delays their power up operations to the MMC_POWER_ON state.
Those hosts needs to change their behavior to enable proper support for
the simple MMC power sequence provider.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Some WLAN chips attached to a SDIO interface, need a reference clock.
Since this is very common, extend the prseq_simple driver to support
an optional clock that is enabled prior the card power up procedure.
Note: the external clock is optional. Thus an error is not returned
if the clock is not found.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many WLAN attached to a SDIO/MMC interface, needs more than one pin for
their reset sequence. For example, is very common for chips to have two
pins: one for reset and one for power enable.
This patch adds support for more reset pins to the pwrseq_simple driver
and instead hardcoding a fixed number, it uses the of_gpio_named_count()
since the MMC power sequence is only built when CONFIG_OF is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is coming to fix compatibility issue of BKOPS_EN field of EXT_CSD.
In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits:
Bit 0 - MANUAL_EN
Bit 1 - AUTO_EN
In previous eMMC revisions, only Bit 0 was supported.
Signed-off-by: Alexey Skidanov <alexey.skidanov@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The need for reset GPIOs has several times been pointed out from
erlier posted patchsets. Especially some WLAN chips which are
attached to an SDIO interface may use a GPIO reset.
The reset GPIO is asserted at initialization and prior we start the
power up procedure. The GPIO will be de-asserted right after the power
has been provided to the card, from the ->post_power_on() callback.
Note, the reset GPIO is optional. Thus we don't return an error even if
we can't find a GPIO for the consumer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
To add the core part for the MMC power sequence, let's start by adding
initial support for the simple MMC power sequence provider.
In this initial step, the MMC power sequence node are fetched and the
compatible string for the simple MMC power sequence provider are
verified.
At this point we don't parse the node for any properties, but instead
that will be handled from following patches. Since there are no
properties supported yet, let's just implement the ->alloc() and the
->free() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
System on chip designs may specify a specific MMC power sequence. To
successfully detect an (e)MMC/SD/SDIO card, that power sequence must
be followed while initializing the card.
To be able to handle these SOC specific power sequences, let's add a
MMC power sequence interface. It provides the following functions to
help the mmc core to deal with these power sequences.
mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data.
mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up().
mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up().
mmc_pwrseq_power_off()- Invoked from mmc_power_off().
mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data.
Each MMC power sequence provider will be responsible to implement a set
of callbacks. These callbacks mirrors the functions above.
This patch adds the skeleton, following patches will extend the core of
the MMC power sequence and add support for a specific simple MMC power
sequence.
Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(),
host drivers needs to make use of this API to enable the support for
MMC power sequences. Moreover the MMC power sequence support depends on
CONFIG_OF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Both callers of mmc_start_request() call mmc_card_removed()
so move that call into mmc_start_request().
This patch is preparation for adding re-tuning support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.
To make it possible for omap_hsmmc (and maybe others) to be converted
to use slot-gpio, add 'mmc_gpio_request_cd_isr' which provide an
alternate isr to be register by the slot-gpio code.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check if the card is alive after a successful reset. This allows
us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only
card reset interface.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds SDIO devicetree subnode parsing to the mmc core. While
SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This patch makes it possible to supply this
information from the devicetree. SDIO drivers will find a pointer
to the devicenode in their devices of_node pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Misc. cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.
Those are now intended to be used only by the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
By moving the allocation of the slot-gpio data into mmc_alloc_host(),
we can remove the slot-gpio internal calls to mmc_gpio_alloc().
This means mmc_gpio_alloc() has now only one caller left, which
consequence allow us to simplify and remove some of the slot-gpio code.
Additionally, this makes the slot-gpio mutex redundant, so let's remove
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent when freeing data, let's move the idr_remove() call
from mmc_free_host() into the ->dev_release() callback for the class
device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.
In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We had a mix of using the class device and the parent device while
allocating data through the devm_* managed functions.
Let's be more consistent and always use the parent device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.
Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.
As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.
This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set
Fixes: 577fb13199 (mmc: rework selection of bus speed mode)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD card spec, Add a manual tuning command function
for SDR104/HS200.
Sending command 19 or command 21 to read data and compare with the
tunning block pattern.
This patch will help to decrease some platform private codes in SDHCI
platform_execute_tuning() callbacks.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Voltage Switch Procedure
This patch is to fix an issue found on mb86s7x platforms.
[symptom]
There are some UHS-1 SD memory cards sometimes cannot be detected correctly,
e.g., Transcend 600x SDXC 64GB UHS-1 memory card.
During Signal Voltage Switch Procedure, failure to switch is indicated
by the card holding DAT[3:0] low.
[analysis]
According to SD Host Controller Simplified Specification Version 3.00
chapter 3.6.1, the Signal Voltage Switch Procedure should be:
(1) Check S18A; (2) Issue CMD11; (3) Check CMD 11 response;
(4) Stop providing SD clock; (5) Check DAT[3:0] should be 0000b;
(6) Set 1.8V Signal Enable; (7) Wait 5ms; (8) Check 1.8V Signal Enable;
(9) Provide SD Clock; (10) Wait 1ms; (11) Check DAT[3:0] should be 1111b;
(12) error handling
With CONFIG_MMC_CLKGATE=y, sometimes there is one more gating/un-gating
SD clock between (2) and (3). In this case, some UHS-1 SD cards will hold
DAT[3:0] 0000b at (11) and thus fails Signal Voltage Switch Procedure.
[solution]
By mmc_host_clk_hold() before CMD11, the additional gating/un-gating
SD clock between (2) and (3) can be prevented and thus no failure at (11).
It has been verified with many UHS-1 SD cards on mb86s7x platforms and
works correctly.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:
mmc_power_off():
For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
chip_select = MMC_CS_HIGH, before we left them as they were.
For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
MMC_BUSMODE_OPENDRAIN as before.
These two changes should not be a problem since the device will be
powered off anyway.
mmc_do_hw_reset():
Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
care of by mmc_init_card() and mmc_attach_mmc().
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to previous patches, all callers of mmc_send_cxd_data() now
allocates their buffers from the heap. This enables us to simplify
mmc_send_cxd_data() by removing the support of handling buffers, which
are allocated from the stack.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.
Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC spec version is < CSD_SPEC_VER_4, there aren't support for
the EXT_CSD register. Since max_dtr is fetched from there, it will
default to zero, which thus isn't needed to verify.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The validation of the buswidth and the MMC spec version in
__mmc_select_powerclass() is redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_send_ext_csd() is an exported function used by both the mmc core
and the mmc block layer. Let's remove the local duplicated definition
in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Presumably ->slotno is normally fairly small and the shift doesn't wrap
but static checkers will complain about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct mmc_driver adds an extra layer on top of the struct
device_driver. That would be fine, if there were a good reason, but
that's not the case.
Let's simplify code by converting to the common struct device_driver
instead and thus also removing superfluous overhead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having specific mmc system PM callbacks for the mmc driver,
let's convert to use the common ones.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While starting the bkops the previously prepared request should be canceled
and restarted after the bkops. As the prepared resource might already
setup the dma channels and ready to be started. Now with the arrival of bkops
request this prepared request can be serviced ONLY after the bkops. So
holding on to the prepared request in the host driver is confusing at
this point in time, so it makes sense to cleanup such dangling requests and
reissue this request once bkops is done.
Canceling the prepared request would give opportunity to the host drivers
to perform cleanup on the prepared request.
Without this patch host drivers like mmci gets confused when a blocking
request like send_ext_csd(CMD8) is issued while there is already a prepared
request. With the help of this patch, the driver can better manage such
blocking requests and cleanup the prepared requests which are not started yet.
Without this patch I hit below crash on Qualcomm APQ8064 based IFC6410 board
with mmci host driver.
mmci-pl18x 12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address 40000000
pgd = c0204000
[40000000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc7-linaro-multi-v7 #1
task: c0c9d7e0 ti: c0c92000 task.ti: c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<c021efc0>] lr : [<c021af18>] psr: 400f0193
sp : c0c93e20 ip : c0c9a478 fp : c08ea538
r10: c0c9f548 r9 : 00000002 r8 : e97d9000
r7 : 00000200 r6 : c0c9d504 r5 : c0db0880 r4 : 00000000
r3 : 0000003f r2 : 00000040 r1 : 40000200 r0 : 40000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: a9ef406a DAC: 00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20: c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40: 00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60: 00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80: 00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0: e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0: 00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0: 00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00: f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20: c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80: 7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0: c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0: ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0: c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<c021efc0>] (v7_dma_inv_range) from [<c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<c021af18>] (__dma_page_dev_to_cpu) from [<c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<c021b574>] (arm_dma_unmap_sg) from [<c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<c072ea58>] (mmci_dma_unmap.isra.16) from [<c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<c072f534>] (mmci_data_irq) from [<c072f6b4>] (mmci_irq+0xe0/0x114)
[<c072f6b4>] (mmci_irq) from [<c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<c0280a60>] (handle_irq_event_percpu) from [<c0280b60>] (handle_irq_event+0x44/0x64)
[<c0280b60>] (handle_irq_event) from [<c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<c028369c>] (handle_fasteoi_irq) from [<c0280278>] (generic_handle_irq+0x2c/0x3c)
[<c0280278>] (generic_handle_irq) from [<c020f080>] (handle_IRQ+0x40/0x90)
[<c020f080>] (handle_IRQ) from [<c02088e4>] (gic_handle_irq+0x38/0x68)
[<c02088e4>] (gic_handle_irq) from [<c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20: 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff
[<c0212800>] (__irq_svc) from [<c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<c071bd24>] (qcom_lpm_enter_spc) from [<c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<c0719a44>] (cpuidle_enter_state) from [<c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<c0276198>] (cpu_startup_entry) from [<c0be0bc4>] (start_kernel+0x384/0x390)
Code: 1e070f3e e1110003 e1c11003 1e071f3e (ee070f36)
---[ end trace cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_init_card function some of the branches in error handling paths
go to "err" label, which skips removing of newly allocated card structure,
that will actually not be used. Fix that by using proper "free_card" label.
Also, some messages in these branches are reported as warnings,
although the operation processing is not continued. Change these
messages to error level.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The debug messages with commands execution results, that are printed
after processing the request, do not include results of sbc (set block count)
part of request. Add the debug message for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some request fields are initialized just before request processing
for sanity purposes. This is done for command, data, and stop parts
of the request, but not for sbc (set block count) part. Add such
initialization for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
commit 98e90de99a
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.
It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.
echo 0 > /sys/kernel/debug/mmc0/clock
However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency. So correct the warning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously only the ACPI PM domain was supported by the sdio bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Checks EXT_CSD_PARTITION_SETTING_COMPLETED bit before
computing enhanced user area offset and size, and
adding mmc general purpose partitions. The two needs
EXT_CSD_PARTITION_SETTING_COMPLETED bit be set to be
valid (as described in JEDEC standard).
Warn user in case of misconfiguration.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace ext_csd "enhanced_area_en" attribute by
"partition_setting_completed". It was used whether or
not enhanced user area is defined and without checks of
EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move code that manages user area and general purpose
partitions into functions.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches the central MMC OF parser to use gpio descriptors
instead of grabbing GPIOs explicitly from the device tree.
This strips out an unecessary use of the integer-based GPIO
API that we want to get rid of, cuts down on code as the
gpio descriptor code will handle active low flags.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the slot GPIO driver gets the GPIO to be used for card
detect, it is now possible to specify a flag to have the line
set up as input. Get rid of the explicit setup call for input
and use the flag.
The extra argument works as there are transition varargs
macros in place in the <linux/gpio/consumer.h> header, in
the future we will make the flags argument compulsory.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.
So the sequence will be:
if (host and device can both support 1.2v IO)
use 1.2v IO;
else if (host and device can both support 1.8v IO)
use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Tested-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As stated by the eMMC 5.0 specification, a chip should not be rejected
only because of the revision stated in the EXT_CSD_REV field of the
EXT_CSD register.
Remove the control on this value, the control of the CSD_STRUCTURE field
should be sufficient to reject future incompatible changes.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initialization of some SD-cards fails because the card never
leaves the busy state. Aid trouble shooting by indicating this in the
kernel log.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The runtime PM core handles a runtime_idle callback set to NULL as one
returning 0. So, let's just set it to NULL instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Rather than the SDIO support spawning it's own thread for handling card
interrupts, use the generic IRQ infrastructure for this, triggering it
from the host interface's interrupt handling directly.
This avoids a race between the parent thread waiting to receive an
interrupt response from the card, and the slow startup from the sdio
irq thread, which can occur as a result of high system load (eg, while
udev is running.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host,
for those host driver's that can't distinguish this in runtime.
Specially, if host can support HS400, it means that host can also
support HS200.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high
speed DDR interface timing from HS200. Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Jackey Shen <jackey.shen@amd.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.
The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Power class is changed once only after selection of bus modes
including speed and bus-width finishes finally.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Device types which are supported by both host and device can be
identified when EXT_CSD is read. There is no need to check host's
capability anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host. Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.
In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11. A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.
It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted. This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The sdio func device is added to the driver model after the card
device.
This means the sdio func device will be suspend before the card device
and thus resumed after. The consequence are the mmc core don't
explicity need to protect itself from receiving sdio requests in
suspended state. Instead that can be handled from the sdio bus, which
is thus invokes the PM callbacks instead of old dummy function.
In the case were the sdio func driver don't implement the PM callbacks
the mmc core will in the early phase of system suspend, remove the
card from the driver model and thus power off it.
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: xiaoming wang <xiaoming.wang@intel.com>
Tested-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board,
we get the following kernel warning:
WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378()
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8
Workqueue: kmmcd mmc_rescan
[<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
[<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
[<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24)
[<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378)
[<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4)
[<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164)
[<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8)
[<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8)
[<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c)
[<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174)
[<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8)
[<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec)
[<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464)
[<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0)
[<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34)
The error is due to an invalid value in CSD register of a specific 2GB
micro SD card. The CSD version of this card is 1.0 but the TACC field
has the invalid value 0.
cid:0000005553442020000000000000583f
csd:00000032535a83bfedb7ffbf1680003f
date:08/2005
erase_size:512
fwrev:0x0
hwrev:0x0
manfid:0x000000
name:USD
oemid:0x0000
preferred_erase_size:4194304
scr:0225000000000000
serial:0x00000000
type:SD
Since the kernel is making use of this TACC field to calculate the SD
card timeout, an invalid value 0 leads to a warning at
mxs_ns_to_ssp_ticks() and later the following misleading error message
appears in a loop:
mxs-mmc 80010000.ssp: card claims to support voltages below defined range
mxs-mmc 80010000.ssp: no support for card's volts
mmc0: error -22 whilst initialising MMC card
This error is only found on this 2GB SD card on mxs platform.
On x86 this card works without any problems.
The following patch based on the work of Peter Chan and Otavio Salvador.
It catches the case that the determined timeout is still 0 and sets it
to a valid value.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTRLHLAAoJEHNBYZ7TNxYMoqEQAOULXl1SHt0aHn5I0cfdVnRm
J3i56MqarwXQOse/qJrg8/uKsggAu0ivTlQ7x1h6bpXmzHqvOtZhSoO9BqGEvxOU
WNeA9ouaKMx3gCpIAwl9Odox+d2E+91nRfxU3fZTDITy554fREXmIpWiidjFPR7n
2oHT0yvGuLjunTC8MhxSB0OsggoIDXDTVPxrcf2k+AcAZAMlCMDNirN9+JbhiVM9
PNESapMyQAbFy18BGzCt5lO2o6aRileaSdX4BFTW4lx2LSPryUVV3cnfIH4zlytW
joVDWyU5kAtQgfhoEhTsWJld+cwHsMUrl/FOfhMvBWbPMxLJnbFx8b459nKJDM5j
NUo29KQxxHgWblGYx+F5SYuTloqWtX5iQWsez9g38Z/3UtjHR++o3+auwTFsZFRe
7EusZqsXdKggx1iiW/5afgb+tFOiCe5WOOQv29YdqWurPhaSK2Nr1aprD4RRiMeT
IG9qBLhHFLl8Pv0nTdEGbJHhAhihja6w2ul+i/8JSaDOYAGFbEn47MC8JfrKAnpw
WovxkSqMroMhjI+51cwJnVtdczQWx5kpjqDY0VaJlKvOfcwyOuyTU+s2vrHVDMZS
a0HgaXeVxr5IcDTz2zo1f6UbM4k2z/Ka0LOOSPqyOYOpFuT6VkXhgOVq6fsRpnaN
/9CUirULwF5ej0oz38hk
=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Add functions to request a CD GPIO using the GPIO descriptor API.
Note that the new request function is paired with mmc_gpiod_free_cd()
not mmc_gpio_free_cd(). Note also that it must be called prior to
mmc_add_host() otherwise the caller must also call
mmc_gpiod_request_cd_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, split out
CD IRQ request into a separate function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, switch from
recording GPIO numbers to recording GPIO descriptors.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
When sending the sleep command for host drivers supporting
MMC_CAP_WAIT_WHILE_BUSY, we need to confirm that max_busy_timeout is
big enough comparing to the sleep timeout specified from card's
EXT_CSD. If this isn't case, we use a R1 response instead of R1B and
fallback to use a delay instead.
Do note that a max_busy_timeout set to zero by the host, is interpreted
as it can cope with whatever timeout the mmc core provides it with.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Conform to the eMMC spec and use the CMD6 generic timeout from the
EXT_CSD register, when switching to HS200 mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.
Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.
For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.
In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.
Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.
For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.
To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
There are no active users of this host capability. The primary reason
for adding this cap was due to a bug in ux500 boot loader code, which
is not a relevant issue any more. So, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several
validations of a present bus_ops callback became redundant. Let's
remove these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.
To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.
By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- Avoid get_cd() on cards marked nonremovable.
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC.
- dwmmc: Support Hisilicon K3 SoC controllers.
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM.
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540.
- tegra: Support Tegra124 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wZBx
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.14:
Core:
- Avoid get_cd() on cards marked nonremovable
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC
- dwmmc: Support Hisilicon K3 SoC controllers
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540
- tegra: Support Tegra124 SoCs"
* tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits)
mmc: sdhci-pci: Fix possibility of chip->fixes being null
mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend
mmc: sdhci: Allow for long command timeouts
mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling
mmc: sdhci: fix lockdep error in tuning routine
mmc: dw_mmc: k3: remove clk_table
mmc: dw_mmc: fix dw_mci_get_cd
mmc: dw_mmc: fix sparse non static symbol warning
mmc: sdhci-esdhc-imx: fix warning during module remove function
mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context
mmc: core: sd: implement proper support for sd3.0 au sizes
mmc: atmel-mci: add vmmc-supply support
mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield
mmc: sdhci: add quirk for broken HS200 support
mmc: arasan: Add driver for Arasan SDHCI
mmc: dw_mmc: add dw_mmc-k3 for k3 platform
mmc: dw_mmc: use slot-gpio to handle cd pin
mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts
mmc: sdhci-pci: break out definitions to header file
mmc: tmio: fixup compile error
...
Conflicts:
MAINTAINERS
Polling SDIO_CCCR_INTx could create a fake interrupt with Marvell
SD8797 card. Add a quirk to handle this case. The fixup here is
to issue a dummy CMD52 read to function 0 register 0xff, and this
dummy read must be right after SDIO_CCCR_INTx is read.
Patch has been verified on a dw_mmc controller (Samsung Chromebook)
with MMC_CAP_SDIO_IRQ disabled.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This reverts and updates commit 77776fd0a4 ("mmc: sd: fix the
maximum au_size for SD3.0"). The au_size for SD3.0 cannot be achieved
by a simple bit shift, so this needs to be implemented differently.
Also, don't print the warning in case of 0 since 'not defined' is
different from 'invalid'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: stable <stable@vger.kernel.org> # [3.12, 3.13]
Signed-off-by: Chris Ball <chris@printf.net>
Non removable cards are always present, so do not call get_cd for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC_CAP_UHS_DDR50 must work on 1.8v.
However, the eMMC DDR mode can work on either 1.8v or 3.3v and
should not depend on UHS_DDR50.
So get rid of this limitation to let controller without 1.8v
signal voltage support can also work for eMMC DDR mode if it claims.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modify acpi_preset_companion() to take a struct acpi_device pointer
instead of an ACPI handle as its second argument and redefine it as
a static inline wrapper around ACPI_COMPANION_SET() passing the
return value of acpi_find_child_device() directly as the second
argument to it. Update its users to pass struct acpi_device
pointers instead of ACPI handles to it.
This allows some unnecessary acpi_bus_get_device() calls to be
avoided.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # for ATA binding
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
In some environments it is to prefer to postpone the resume of the card
device until runtime_resume is being carried out, since it will mean a
signficant decrease of the total system resume time.
The reason of the decreased resume time is simply because of the actual
re-initalization of the card, which typically takes hundreds of
milliseconds, is performed outside the resume sequence and wont thus
affect it.
For removable card, the detect work tries to re-detect the card to make
sure it is still present, as a part of that sequence the card will also
be runtime_resumed and thus also fully resumed.
For a non-removable card, typically a mmc blk request will trigger a
runtime_resume and thus fully resume the card. This also means the
first request will likely suffer from an inital latency since the
re-initialization of the card needs to be performed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card device is considered as in-active after it has been suspended.
To prevent any further runtime PM requests in suspend state, we then
disable runtime PM.
After the card device has been resumed, we shall consider it as active,
like we also do after a probe sequence. When resumed, we can safely
enable runtime PM again.
This will make sure the PM core can request the card device to go to
in-active state after a resume has been completed. Previously we had to
wait for new pm_runtime_get->pm_runtime_put cycle to be executed.
Additionally, once a resume has been carried out, update the last busy
mark. At the moment this will have no effect but if the PM core will
respect autosuspend enabled devices, when it directly triggers a
runtime_suspend from a runtime_idle, it will mean the card device will
be scheduled for a delayed runtime_suspend instead of done immediately.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: core: Push common suspend|resume code into each bus_ops"
moved the responsibility for doing mmc_power_up|off into each
suspend/resume bus_ops. When using MMC_CAP_AGGRESSIVE_PM, through the
runtime callbacks, calls to mmc_power_up|off became redundant.
When removing them, we are also able to remove the calls to
mmc_claim|release_host, thus simplifing code a bit more.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The are no more users of the deprecated mmc_suspend|resume_host API,
so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We want to give user space provision to fully consume a card
insert/remove event, when the event was caused by a wakeup irq.
By signaling the wakeup event for a time of 5 s for devices configured
as wakeup capable, we likely will be prevent a sleep long enough to let
user space consume the event.
To enable this feature, host drivers must thus configure their devices
as wakeup capable.
This is a reworked implementation of the old wakelocks for the mmc
subsystem, originally authored by Colin Cross and San Mehat for the
Android kernel. Zoran Markovic shall also be given cred for recently
re-trying to upstream this feature.
Cc: San Mehat <san@google.com>
Cc: Colin Cross <ccross@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.
Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.
A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.
A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At several places in mmc_sdio_init_card function the cached mask in
host->ocr were being updated. To simplify code, we make use of an
local ocr parameter instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The retry and fallback mechanism when failing to switch to 1.8V
signaling voltage is handled by the SDIO card init function. Thus we
can remove the duplicated old code from the attach function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the MMC bus code to use the
correct field.
Cc: Chris Ball <cjb@laptop.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Konstantin Dorfman <kdorfman@codeaurora.org>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While speed mode is changed, CMD13 cannot be guaranteed.
According to the spec., it is not recommended to use CMD13
to check the busy completion of the timing change.
If CMD13 is used in this case, CRC error must be ignored.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
cscope says there are no callers for mmc_try_claim_host in the kernel.
No reason to keep it.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since SD Physical Layer specification V3.0, AU_SIZE is supported up
to 0xf. So If SD-card is supported v3.0, then max_au should be 0xf.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In function mmc_sd_init_card, if command 3/9/7 got failed, mmc_card
allocated just before won't be freed. This would cause memory leak.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for the vmmcq
regulator can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Core:
- Add support for eMMC 5.1 devices.
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power management
of eMMC/SD between requests, using runtime PM.
- Add an ioctl to perform the eMMC 4.5 Sanitize command; sample code at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs.
- dw_mmc: Add support for Altera SoCFPGAs.
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable cards.
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs.
- sdhi/tmio: Add DT DMA support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJR2v+uAAoJEHNBYZ7TNxYMIT8P/0W2g0efrm1+c679L6x/ToaJ
rsZF4J+gv/yMPPNNxV03BL8NSuU7EyniMBeRAutykCTfhr/NoToYnPRR4trAsN9G
J/GAhXbMFQj8YTvOUhMVjzH4B9z2FNfZ2L4mx/9kBLcBphWvafKXmfoD4WqI8b17
WS+vGbEdYmiQKCjlZnWvkiNiGWZmhmp49iAL0QiZsFVizGQaWeTZdzt95JV62cUw
WDA/TGh1L1Zezf68i5iwJsW3mWuZS7iemeL4jFN8owyBU5wXCNae/4TjbIR0zpYr
HVGgkQLX+FLFg+EJe1s/A1feD3ZwPWymoImuL44d1VsQYO6cTEKHd78qSNPuDFBI
oATvJR/TgrdvHO17iQgVwa104Q+zz9r3/3eC1qZhUIV+oq8Xv6aBckGlhNIc42ef
YuFTxOnY3VF6DmOwXFgzyrHnQemLn+AzHqM5zVBjF7oRDyD5MnNaCb/AQ7xinlfd
V/VY8N8pJLSV2IC5OLjVyqovBHb4nwiGIwrawWJA83uw7QyLbAMafXyuNAVEsaiX
olVgNH8wuEye5f5Y6ZKXEGzKrKvIH+3pFXL3Q5AA8Kv8+851oMFgjdEg+WDOKc6j
7DoQPIrmwRNi789dyzbwrKfCOPIW6ClALc4H3QIvu/GDEbeexfjDcfYj8VPM8Wuk
hOHYcxEDD9k3BSqhnaI+
=c/CM
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.11:
Core:
- Add support for eMMC 5.1 devices
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
management of eMMC/SD between requests, using runtime PM
- Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code
at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
- dw_mmc: Add support for Altera SoCFPGAs
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
cards
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
- sdhi/tmio: Add DT DMA support"
* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
mmc: bcm281xx SDHCI driver
mmc: sdhci: add card_event callback to sdhci
mmc: core: Fixup Oops for SDIO shutdown
mmc: sdhci-pci: add another device id
mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
mmc: esdhc: Add support for 8-bit bus width and non-removable card
mmc: core: production year for eMMC 4.41 and later
mmc: omap: remove unnecessary #if 0's
mmc: sdhci: fix ctrl_2 on super-speed selection
mmc: dw_mmc-pltfm: add Rockchip variant
mmc: dw_mmc-pltfm: move probe and remove below dt match table
mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
mmc: sdhci: fix caps2 for HS200
sdhci-pxav3: Fix runtime PM initialization
mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Enable power_off_notify for eMMC shutdown sequence
...
Commit "mmc: core: Handle card shutdown from mmc_bus" introduced an
Oops in the shutdown sequence for SDIO.
The drv pointer, does not exist for SDIO since the probing of the SDIO
card from the mmc_bus perspective is expected to fail by returning
-ENODEV.
This patch adds the proper check for the pointer before calling it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The field containing the production date in the CID register only uses
4 bits to encode the year, starting from 1997 in the original standard.
In 2013, the production year field contains 0, and the kernel reports a
1997 production date.
The eMMC 4.51 specification adds a new interpretation rule. For all
devices implementing the 4.41 specification or later, the production
year field will be interpreted as a value between 2010 and 2025, with
0 corresponding to 2013.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DT-binding for MMC_CAP2_FULL_PWR_CYCLE, is used to indicate whether
it is possible to perform a full power cycle of the card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP2_FULL_PWR_CYCLE shall be set by host drivers which are able to
do a complete power cycle of the card. In the eMMC case that includes
both vcc and vccq.
This CAP is providing the protocol layer with important information,
needed to take optimized decisions during card initialization and in
the suspend/resume sequence.
MMC_CAP2_POWEROFF_NOTIFY is replaced by MMC_CAP2_FULL_PWR_CYCLE, since
it makes sense to use a wider scope for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In suspend mode it is important to save power. If the host is able to
cut buth vcc and vccq, the MMC_CAP2_POWEROFF_NOTIFY shall be set. It
will mean the card will be completely powered down at suspend and the
power off notification cmd will be sent prior power down.
It seems common not being able to cut both vcc and vccq for a host. In
this situation we issue the sleep cmd in favor of the power off
notification cmd, to save more power.
While maintainng the above policy, we also want to make use of the
power off notification in the shutdown sequence, even in the case were
the host has not set MMC_CAP2_POWEROFF_NOTIFY, since we know vcc and
vccq will regardless be cut.
We accomplish this by always enabling the power off notification byte
in the EXT_CSD and issue the power off notification when either
MMC_CAP2_POWEROFF_NOTIFY is set or we are executing a shutdown.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The shutdown sequence of an (e)MMC is very similar to a suspend. We
re-use the suspend function and tell it we are not in suspend context.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Depending on the context of the operation while powering down the card,
either POWER_OFF_NOTIFY_SHORT or POWER_OFF_NOTIFY_LONG will be used. In
suspend context a short timeout is preferred while a long timeout would
be acceptable in a shutdown/hibernation context.
We add a new parameter to the mmc_suspend function so we can provide an
indication of what notification type to use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the SD .shutdown callback we re-use the SD suspend function since
it performs the relevant actions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding an optional .shutdown callback to the bus_ops struct we
provide the possibility to let each bus type handle it's shutdown
requirements.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host should be responsible to suspend|resume the host and not the
card. This patch changes this behaviour, by moving the responsiblity
to the mmc bus instead which already holds the card device.
The exported functions mmc_suspend|resume_host are now to be considered
as depcrecated. Once all host drivers moves away from using them, we
can remove them. As of now, a successful error code is always returned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.
This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For every bus_ops type the .remove callback always exist, thus there
are no need to check the existence of it, before we decide to call it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the new eMMC5.1 spec, there is a new EXT_CSD register with
the revision number(EXT_CSD_REV) 7. This patch updates the check
for ext-csd.rev number as 7.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In addition to just logging errors encountered during DT parsing or
allocating GPIO slots for CD/WP, mmc_of_parse() now returns with an error.
In particular, this is needed if the GPIO allocation may return
EPROBE_DEFER.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Use the saved values in card->ext_csd when selecting power class.
By doing this the power class will be selected even if mmc_init_card
is called with oldcard != NULL, which is the case after a suspend/resume.
Today ext_csd is NULL if mmc_init_card is called with oldcard != NULL
and power class will not be selected.
According to the eMMC specification the POWER_CLASS value is reset after
power failure, H/W reset assertion and any CMD0 reset.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Acked By: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO is the only protocol that uses runtime pm for the card device
right now. To provide the option for sd and mmc to use runtime pm as
well the bus_ops callback are extended with two new functions. One for
runtime_suspend and one for runtime_resume.
This patch will also implement the callbacks for SDIO to make sure
existing functionality is maintained. It also prepares to move
away from using the mmc_power_restore_host API, since it is not
needed when using runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move mmc suspend specific operations to be executed from the .suspend
callback in the mmc bus_ops. This simplifies the mmc_suspend_host
function which is supposed to handle nothing but common suspend tasks.
Since eMMC can be considered non-removable there are no need to check
for ongoing bkops at PM_SUSPEND_PREPARE notification so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.
Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only execute tuning for sd and sdio devices that are using
SDR50 or SDR104.
Make sure clock is hold during tuning for sdio devices.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Acked-by: Johan Rudholm <jrudholm@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping mmc_power_up()
at boot/initialization time if it's already happened, for performance
(faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being put
into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed slowly;
we were missing card removal events if the card retained contact with
the slot pads for long enough to reply to a CMD13 while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use mmc_of_parse().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Pr7P
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa5501890d introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3500ed90b2.
The reverted patch caused a significant performance regression when
booting with the root file system on eMMC.
Before the patch:
[ 1.625623] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
After the patch:
[ 1.935851] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
That was an addition of 310 ms which is a 19% performance degradation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts are added asynchronously. We need to wait until detect returns to
avoid failed root filesystem mounts.
VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
mmc0: host does not support reading read-only switch. assuming write-enable.
1f00 256 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 2560 mtdblock2 mmc0: new SDHC card at address b368
(driver?)
1f03 29696 mtdblock3 (driver?)
1f04 16384 mtdblock4 mmcblk0: mmc0:b368 USD 3.72 GiB
(driver?)
mmcblk0: p1
b300 3910656 mmcblk0 driver: mmcblk
b301 3906560 mmcblk0p1 00000000-01
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Function _mmc_detect_card_removed will be called to know whether
the card is still present when host->bus_ops->detect is called.
In current code, the return value of this function generally only
depend on the result of sending cmd13 to card, which may not safe
for card with detection support like slot gpio detection.
Because the communication status between host and card may out of
sync with the detect status if remove the card slowly or hands shake
during the process. The direct reason is the async between card
detect switch and card/slot pad contaction in hardware, which is
defined by spec.
The spec define card insert/remove sequence as below (both standard size
SD card and MicroSD card have the same sequence):
"Part 1 Standard Size SD Card Mechanical Addendum Ver4.00 Final,
Appendix C: Card Detection Switch" (Take normally open type as example)
a)SD card insertion sequence:
The card detection switch should be turned on after all SD card
contact pads are connected to the host connector contact pads.
b)SD removal sequence:
The card detection switch should be turned off when the SD card
is just going to be removed and before any SD card contact pad is
disconnected from the host connector contact pad.
Below is the sequence when this issue occur (Take slot gpio detection
as example and remove the card slowly during the process):
1. gpio level changed and card detect interrupt triggered.
2. mmc_rescan was launched.
3. the card pads were still contacted with the slot pads because of slow
removal. So _mmc_detect_card_removed and mmc_rescan think card was
still present (cmd13 succeed).
4. card pads were discontacted from the card slot pads.
So the card was actually removed finally but the card removal event
has been missed by system.
The interval length between step 1 and step 4 depends on the
card removal speed. If it's longer than the detect work schedule
delay which is 200ms, this issue will likely happen.
This patch add the card detect status check in function
_mmc_detect_card_removed if cmd13 check succeed and host->ops->get_cd
provided. If get_cd detect no card present then schedule another detect
work 200ms later.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
