>> drivers/dma/mv_xor_v2.c:647:36: sparse: constant 0xFFFF00000000 is so big it is long
include/linux/device.h:678:13: sparse: undefined identifier '__builtin_mul_overflow'
include/linux/device.h:678:13: sparse: call with no type!
Use lower_32_bits and upper_32_bits to set the hw_desq address, instead of
using constant.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To get more coverage, enable COMPILE_TEST for this driver.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Completion callback should happen after dma_descriptor_unmap() has
happened. This allow the cache invalidate to happen and ensure that
the data accessed by the upper layer is in memory that was from DMA
rather than stale data. On some architecture this is done by the
hardware, however we should make the code consistent to not cause
confusion.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is in preparation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mv_xor_v2 driver uses a tasklet, initialized during the probe()
routine. However, it forgets to cleanup the tasklet using
tasklet_kill() function during the remove() routine, which this patch
fixes. This prevents the tasklet from potentially running after the
module has been removed.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine device should explicitly call devm_free_irq() when using
devm_request_irq().
The irq is still ON when devices remove is executed and irq should be
quiesced before remove is completed.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds dma_pause operation. This patch is based on
Muhammad Hamza Farooq's patch.
After this patch applied, an issue that the sh-sci driver with
high baud rate might cause data lost disappeared because the DMAC
is possible to transmit between [1] and [2] below, and then
the residue of [1] is not true:
In rx_timer_fn() of the sh-sci.c:
dmaengine_pause();
...
dmaengine_tx_status(); /* [1] */
...
dmaengine_terminate_all(); /* [2] */
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new function rcar_dmac_clear_chcr_de() to simplify
adding pause function later.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It appears that the driver misses the support of dmaengine_terminate_sync().
Since many of callers expects this behaviour implement the new
device_synchronize() callback to allow proper synchronization when stopping
a channel.
Fixes: b36f09c3c4 ("dmaengine: Add transfer termination synchronization support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It appears that the driver misses the support of dmaengine_terminate_sync().
Since many of callers expects this behaviour implement the new
device_synchronize() callback to allow proper synchronization when stopping
a channel.
Fixes: b36f09c3c4 ("dmaengine: Add transfer termination synchronization support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes an issue that unexpected retransfering happens
if TCR is set to 0 before rcar_dmac_sync_tcr() writes DE bit to
the CHCR register. For example, sh-sci driver can reproduce this
issue like below:
In rx_timer_fn(): /* CHCR DE bit may be set to 1 */
dmaengine_tx_status()
rcar_dmac_tx_status()
rcar_dmac_chan_get_residue()
rcar_dmac_sync_tcr() /* TCR is possible to be set to 0 */
According to the description of commit 73a47bd0da ("dmaengine:
rcar-dmac: use TCRB instead of TCR for residue"), "this buffered data
will be transferred if CHCR::DE bit was cleared". So, this patch
doesn't need to check TCRB register.
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Compiler complains (with W=1):
drivers/dma/pl330.c: In function ‘pl330_release_channel’:
drivers/dma/pl330.c:1782:21: warning:
variable ‘pl330’ set but not used [-Wunused-but-set-variable]
struct pl330_dmac *pl330;
^~~~~
Remove the pl330 variable in pl330_release_channel as it is set but
never used.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The format specifier "%p" can leak kernel addresses.
Use "%pK" instead.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cmd_pause' DMA channel capability means that respective DMA engine
supports both pausing and resuming given DMA channel. However, in some
cases it is important to know if DMA channel can be paused without the
need to resume it. This is a typical requirement for proper residue
reading on transfer timeout in UART drivers. There are also some DMA
engines with limited hardware, which doesn't really support resuming.
Reporting pause and resume capabilities separately allows UART drivers to
properly check for the really required capabilities and operate in DMA
mode also in systems with limited DMA hardware. On the other hand drivers,
which rely on full channel suspend/resume support, should now check for
both 'pause' and 'resume' features.
Existing clients of dma_get_slave_caps() have been checked and the only
driver which rely on proper channel resuming is soc-generic-dmaengine-pcm
driver, which has been updated to check the newly added capability.
Existing 'cmd_pause' now only indicates that DMA engine support pausing
given DMA channel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We need to clear channel register in error case as recovery.
The channel is already stopped in such case, thus we don't need to call
rcar_dmac_chan_halt() before clearing.
rcar_dmac_chan_halt() will clear and confirm DE bit.
But it will be failed because channel is already stopped in error case.
In other words, we shouldn't call it then.
Reported-by: Hiroki Negishi <hiroki.negishi.bx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Hiroki Negishi <hiroki.negishi.bx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During system reboot or halt, with lockdep enabled:
================================
WARNING: inconsistent lock state
4.18.0-rc1-salvator-x-00002-g9203dbec90a68103 #41 Tainted: G W
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
reboot/2779 [HC0[0]:SC0[0]:HE1:SE1] takes:
0000000098ae4ad3 (&(&rchan->lock)->rlock){?.-.}, at: rcar_dmac_shutdown+0x58/0x6c
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x208/0x238
_raw_spin_lock+0x40/0x54
rcar_dmac_isr_channel+0x28/0x200
__handle_irq_event_percpu+0x1c0/0x3c8
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xc4/0x12c
generic_handle_irq+0x18/0x2c
__handle_domain_irq+0xa8/0xac
gic_handle_irq+0x78/0xbc
el1_irq+0xec/0x1c0
arch_cpu_idle+0xe8/0x1bc
default_idle_call+0x2c/0x30
do_idle+0x144/0x234
cpu_startup_entry+0x20/0x24
rest_init+0x27c/0x290
start_kernel+0x430/0x45c
irq event stamp: 12177
hardirqs last enabled at (12177): [<ffffff800881d804>] _raw_spin_unlock_irq+0x2c/0x4c
hardirqs last disabled at (12176): [<ffffff800881d638>] _raw_spin_lock_irq+0x1c/0x60
softirqs last enabled at (11948): [<ffffff8008081da8>] __do_softirq+0x160/0x4ec
softirqs last disabled at (11935): [<ffffff80080ec948>] irq_exit+0xa0/0xfc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&rchan->lock)->rlock);
<Interrupt>
lock(&(&rchan->lock)->rlock);
*** DEADLOCK ***
3 locks held by reboot/2779:
#0: 00000000bfabfa74 (reboot_mutex){+.+.}, at: sys_reboot+0xdc/0x208
#1: 00000000c75d8c3a (&dev->mutex){....}, at: device_shutdown+0xc8/0x1c4
#2: 00000000ebec58ec (&dev->mutex){....}, at: device_shutdown+0xd8/0x1c4
stack backtrace:
CPU: 6 PID: 2779 Comm: reboot Tainted: G W 4.18.0-rc1-salvator-x-00002-g9203dbec90a68103 #41
Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
Call trace:
dump_backtrace+0x0/0x148
show_stack+0x14/0x1c
dump_stack+0xb0/0xf0
print_usage_bug.part.26+0x1c4/0x27c
mark_lock+0x38c/0x610
__lock_acquire+0x3fc/0x14d4
lock_acquire+0x208/0x238
_raw_spin_lock+0x40/0x54
rcar_dmac_shutdown+0x58/0x6c
platform_drv_shutdown+0x20/0x2c
device_shutdown+0x160/0x1c4
kernel_restart_prepare+0x34/0x3c
kernel_restart+0x14/0x5c
sys_reboot+0x160/0x208
el0_svc_naked+0x30/0x34
rcar_dmac_stop_all_chan() takes the channel lock while stopping a
channel, but does not disable interrupts, leading to a deadlock when a
DMAC interrupt comes in. Before, the same code block was called from an
interrupt handler, hence taking the spinlock was sufficient.
Fix this by disabling local interrupts while taking the spinlock.
Fixes: 9203dbec90 ("dmaengine: rcar-dmac: don't use DMAC error interrupt")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is using C++ comment style for SPDX line only,
because driver author want it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some member description or colons missing cause build warning with
'W=1' as below:
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'vd' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'num_bd' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'bd_phys' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'buf_tail' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'buf_ptail' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'period_len' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'chn_real_count' not described in 'sdma_desc'
drivers/dma/imx-sdma.c:326: warning: Function parameter or member 'chn_count' not described in 'sdma_desc
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The variable is no longer used, though it is set, so remove it
drivers/dma/imx-sdma.c:1298:6:
warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, i, count;
^~~
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The memory allocation in DMA callbacks should use GFP_NOWAIT, so
update this one and fix code alignment for this call while at it.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are lot of codes overlap between prep_sg and prep_cyclic function.
Add sdma_transfer_init() function to elimated the code overlap.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No this limitation now after virtual dma used since bd is allocated
dynamically instead of static.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 'sdmac->vc.lock' and 'sdmac->desc' can be used as 'lock' and
'enabled' in 'struct sdma_channel sdmac', remove them.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The legacy sdma driver has below limitations or drawbacks:
1. Hardcode the max BDs number as "PAGE_SIZE / sizeof(*)", and alloc
one page size for one channel regardless of only few BDs needed
most time. But in few cases, the max PAGE_SIZE maybe not enough.
2. One SDMA channel can't stop immediatley once channel disabled which
means SDMA interrupt may come in after this channel terminated.There
are some patches for this corner case such as commit "2746e2c389f9",
but not cover non-cyclic.
The common virt-dma overcomes the above limitations. It can alloc bd
dynamically and free bd once this tx transfer done. No memory wasted or
maximum limititation here, only depends on how many memory can be requested
from kernel. For No.2, such issue can be workaround by checking if there
is available descript("sdmac->desc") now once the unwanted interrupt
coming. At last the common virt-dma is easier for sdma driver maintain.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a preparation step to make the adding of virt-dma easier.
We create a struct sdma_desc, move some fields from struct sdma_channel
there and add a pointer from the former to the latter. For now we
allocate the data statically in struct sdma_channel, but with
virt-dma support it will be dynamically allocated.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the quest to remove all stack VLA usage from the kernel[1], this
switches to using a pre-allocated scratch register space, set up with
all other other allocations.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Vertical flip state is exported in xilinx_vdma_config and depending
on IP configuration(c_enable_vert_flip) vertical flip state is
programmed in hardware.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The d->chans[] array has d->dma_requests elements so the > should be
>= here.
Fixes: 8e6152bc66 ("dmaengine: Add hisilicon k3 DMA engine driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The reported residue is already calculated in BURST unit granularity, so
advertise this capability properly to other devices in the system.
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rcar-dmac has 2 types of interrupt, 1) error IRQ (for all),
2) IRQ for each channels.
If error happens on some channels, the error IRQ will be handled
by 1), and "all" channels will be restarted.
But in this design, error handling itself will be problem for
non error channel users.
This patch removes 1) handler, and handles error IRQ on 2)
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Kuninori: updated patch to adjust DMACHCR/DMAOR]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It seems that starting with Skylake Xeon, channel reset clears the
completion address register. Make sure the completion address register is
set again after reset.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 0198d7bb8a ("ASoC: omap-mcbsp: Convert to use the sdma-pcm
instead of omap-pcm") resulted in broken audio playback on OMAP1510
(discovered on Amstrad Delta).
When running on OMAP1510, omap-pcm used to obtain DMA offset from
snd_dmaengine_pcm_pointer_no_residue() based on DMA interrupt triggered
software calculations instead of snd_dmaengine_pcm_pointer() which
depended on residue value calculated from omap_dma_get_src_pos().
Similar code path is still available in now used
sound/soc/soc-generic-dmaengine-pcm.c but it is not triggered.
It was verified already before that omap_get_dma_src_pos() from
arch/arm/plat-omap/dma.c didn't work correctly for OMAP1510 - see
commit 1bdd741991 ("ASoC: OMAP: fix OMAP1510 broken PCM pointer
callback") for details. Apparently the same applies to its successor,
omap_dma_get_src_pos() from drivers/dma/ti/omap-dma.c.
On the other hand, snd_dmaengine_pcm_pointer_no_residue() is described
as depreciated and discouraged for use in new drivers because of its
unreliable accuracy. However, it seems the only working option for
OPAM1510 now, as long as a software calculated residue is not
implemented as OMAP1510 fallback in omap-dma.
Using snd_dmaengine_pcm_pointer_no_residue() code path instead of
snd_dmaengine_pcm_pointer() in sound/soc/soc-generic-dmaengine-pcm.c
can be triggered in two ways:
- by passing pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE from
sound/soc/omap/sdma-pcm.c,
- by passing dma_caps.residue_granularity =
DMA_RESIDUE_GRANULARITY_DESCRIPTOR from DMA engine.
Let's do the latter.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As what former drcmr -1 value meant, add a this as a default to each
channel, ie. that by default no requestor line is used.
This is specifically used for network drivers smc91x and smc911x, and
needed for their port to slave maps.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vkoul@kernel.org>
In order to remove the specific knowledge of the dma mapping from PXA
drivers, add a default slave map for pxa architectures.
This won't impact MMP architecture, but is aimed only at all PXA boards.
This is the first step, and once all drivers are converted,
pxad_filter_fn() will be made static, and the DMA resources removed from
device.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
- Updates to sprd, bam_dma, stm drivers.
- removal of VLAs in dmatest.
- Move TI drivers its own subdir.
- Switch to SPDX tags for ima/mxs dma drivers.
- Simplify getting .drvdata on bunch of drivers by Wolfram Sang.
-----BEGIN PGP SIGNATURE-----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=8mGV
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- updates to sprd, bam_dma, stm drivers
- remove VLAs in dmatest
- move TI drivers to their own subdir
- switch to SPDX tags for ima/mxs dma drivers
- simplify getting .drvdata on bunch of drivers by Wolfram Sang
* tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (32 commits)
dmaengine: sprd: Add Spreadtrum DMA configuration
dmaengine: sprd: Optimize the sprd_dma_prep_dma_memcpy()
dmaengine: imx-dma: Switch to SPDX identifier
dmaengine: mxs-dma: Switch to SPDX identifier
dmaengine: imx-sdma: Switch to SPDX identifier
dmaengine: usb-dmac: Document R8A7799{0,5} bindings
dmaengine: qcom: bam_dma: fix some doc warnings.
dmaengine: qcom: bam_dma: fix invalid assignment warning
dmaengine: sprd: fix an NULL vs IS_ERR() bug
dmaengine: sprd: Use devm_ioremap_resource() to map memory
dmaengine: sprd: Fix potential NULL dereference in sprd_dma_probe()
dmaengine: pl330: flush before wait, and add dev burst support.
dmaengine: axi-dmac: Request IRQ with IRQF_SHARED
dmaengine: stm32-mdma: fix spelling mistake: "avalaible" -> "available"
dmaengine: rcar-dmac: Document R-Car D3 bindings
dmaengine: sprd: Move DMA request mode and interrupt type into head file
dmaengine: sprd: Define the DMA data width type
dmaengine: sprd: Define the DMA transfer step type
dmaengine: ti: New directory for Texas Instruments DMA drivers
dmaengine: shdmac: Change platform check to CONFIG_ARCH_RENESAS
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
This patch adds the 'device_config' and 'device_prep_slave_sg' interfaces
for users to configure DMA, as well as adding one 'struct sprd_dma_config'
structure to save Spreadtrum DMA configuration for each DMA channel.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is one preparation patch, we can use default DMA configuration to
implement the device_prep_dma_memcpy() interface instead of issuing
sprd_dma_config().
We will implement one new sprd_dma_config() function with introducing
device_prep_slave_sg() interface in following patch. So we can remove
the obsolete sprd_dma_config() firstly.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Building kernel with W=1 throws up below warnings:
bam_dma.c:459: warning: Function parameter or member 'dir'
not described in 'bam_chan_init_hw'
bam_dma.c:697: warning: Function parameter or member 'chan'
not described in 'bam_dma_terminate_all'
bam_dma.c:697: warning: Excess function parameter 'bchan'
description in 'bam_dma_terminate_all'
bam_dma.c:964: warning: Function parameter or member 'bchan'
not described in 'bam_start_dma'
Fix these!.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Building kernel with W=1 throws below invalid assignment warnings.
bam_dma.c:676:44: warning: invalid assignment: +=
bam_dma.c:676:44: left side has type unsigned long
bam_dma.c:676:44: right side has type restricted __le16
bam_dma.c:921:41: warning: invalid assignment: +=
bam_dma.c:921:41: left side has type unsigned long
bam_dma.c:921:41: right side has type restricted __le16
Fix them!.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Disabling pm runtime at probe is not sufficient to get BAM working
on remotely controller instances. pm_runtime_get_sync() would return
-EACCES in such cases.
So check if runtime pm is enabled before returning error from bam functions.
Fixes: 5b4a68952a ("dmaengine: qcom: bam_dma: disable runtime pm on remote controlled")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We recently cleaned this code up but we need to update the error
handling as well. The devm_ioremap_resource() returns error pointers on
error, never NULL.
Fixes: e7f063ae1a ("dmaengine: sprd: Use devm_ioremap_resource() to map memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of checking the return value of platform_get_resource(), we can
use devm_ioremap_resource() which has the NULL pointer check and the
memory region requesting.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: 9b3b8171f7 ("dmaengine: sprd: Add Spreadtrum DMA driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With each bus implementing its own DMA configuration callback, there is no
need for bus to explicitly set the force_dma flag. Modify the
of_dma_configure function to accept an input parameter which specifies if
implicit DMA configuration is required when it is not described by the
firmware.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Reviewed-by: Rob Herring <robh@kernel.org>
[hch: tweaked the changelog a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Do DMAFLUSHP _before_ the first DMAWFP to ensure controller
and peripheral are in agreement about dma request state before first
transfer. Add support for burst transfers to/from peripherals. In the new
scheme, the controller does as many burst transfers as it can then
transfers the remaining dregs with either single transfers for
peripherals, or with a reduced size burst for memory-to-memory transfers.
Signed-off-by: Frank Mori Hess <fmh6jj@gmail.com>
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Request IRQ with IRQF_SHARED flag to enable setups with multiple
instances of the core sharing a single IRQ line.
This works out since the IRQ handler already checks if there is
an actual IRQ pending and returns IRQ_NONE otherwise.
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Trivial fix to spelling mistake in dev_err error message text and make
channel plural.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch will move the Spreadtrum DMA request mode and interrupt type
into one head file for user to configure.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Define the DMA data width type to make code more readable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Define the DMA transfer step type to make code more readable.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check, just like before support for Renesas ARM SoCs was added.
Instead of blindly changing all the #ifdefs, switch the main code block
in sh_dmae_probe() to IS_ENABLED(), as this allows to remove all the
remaining #ifdefs.
This will allow to drop ARCH_SHMOBILE on ARM in the near future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both buffer Transfer Length (TLEN if any) and transfer size have to be
aligned on burst size (burst beats*bus width).
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's an ongoing effort to remove VLAs from the kernel
(https://lkml.org/lkml/2018/3/7/621) to eventually turn on -Wvla.
The test already pre-allocates some buffers with kmalloc so turn
the two VLAs in to pre-allocated kmalloc buffers.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have couple of new drivers along with updates to drivers.
- new driver for DesignWare AXI DMAC and MediaTek High-Speed DMA controller
- stm32 dma and qcom bam dma driver updates
- norandom test option for dmatest
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0YWt
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.17-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have couple of new drivers along with updates to drivers:
- new drivers for the DesignWare AXI DMAC and MediaTek High-Speed DMA
controllers
- stm32 dma and qcom bam dma driver updates
- norandom test option for dmatest"
* tag 'dmaengine-4.17-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (30 commits)
dmaengine: stm32-dma: properly mask irq bits
dmaengine: stm32-dma: fix max items per transfer
dmaengine: stm32-dma: fix DMA IRQ status handling
dmaengine: stm32-dma: Improve memory burst management
dmaengine: stm32-dma: fix typo and reported checkpatch warnings
dmaengine: stm32-dma: fix incomplete configuration in cyclic mode
dmaengine: stm32-dma: threshold manages with bitfield feature
dt-bindings: stm32-dma: introduce DMA features bitfield
dt-bindings: rcar-dmac: Document r8a77470 support
dmaengine: rcar-dmac: Fix too early/late system suspend/resume callbacks
dmaengine: dw-axi-dmac: fix spelling mistake: "catched" -> "caught"
dmaengine: edma: Check the memory allocation for the memcpy dma device
dmaengine: at_xdmac: fix rare residue corruption
dmaengine: mediatek: update MAINTAINERS entry with MediaTek DMA driver
dmaengine: mediatek: Add MediaTek High-Speed DMA controller for MT7622 and MT7623 SoC
dt-bindings: dmaengine: Add MediaTek High-Speed DMA controller bindings
dt-bindings: Document the Synopsys DW AXI DMA bindings
dmaengine: Introduce DW AXI DMAC driver
dmaengine: pl330: fix a race condition in case of threaded irqs
dmaengine: imx-sdma: fix pagefault when channel is disabled during interrupt
...
A single register of the controller holds the information for four dma
channels.
The functions stm32_dma_irq_status() don't mask the relevant bits after
the shift, thus adjacent channel's status is also reported in the returned
value.
Fixed by masking the value before returning it.
Similarly, the function stm32_dma_irq_clear() don't mask the input value
before shifting it, thus an incorrect input value could disable the
interrupts of adjacent channels.
Fixed by masking the input value before using it.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Having 0 in item counter register is valid and stands for a "No or Ended
transfer". Therefore valid transfer starts from @+0 to @+0xFFFE leading to
unaligned scatter gather at boundary. Thus it's safer to round down this
value on its FIFO size (16 Bytes).
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update the way Transfer Complete and Half Transfer Complete status are
acknowledge. Even if HTI is not enabled its status is shown when reading
registers, driver has to clear it gently and not raise an error.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch improves memory burst capability using best burst size
according to transferred buffer size from/to memory.
>From now on, memory burst is not necessarily same as with peripheral
burst one and fifo threshold is directly managed by this driver in order
to fit with computed memory burst.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When in cyclic mode, the configuration is updated after having started the
DMA hardware (STM32_DMA_SCR_EN) leading to incomplete configuration of
SMxAR registers.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
>From now on, DMA bitfield is to manage DMA FIFO Threshold.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If serial console wake-up is enabled ("echo enabled >
/sys/.../ttySC0/power/wakeup"), and any serial input is received while
the system is suspended, serial port input no longer works after system
resume.
Note that:
1) The system can still be woken up using the serial console,
2) Serial port input keeps working if the system is woken up in some
other way (e.g. Wake-on-LAN or gpio-keys), and no serial input was
received while suspended.
To fix this, replace SET_LATE_SYSTEM_SLEEP_PM_OPS() by
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(), as the callbacks installed by the
former happen too early resp. late in the suspend resp. resume process.
Reported-by: RVC test team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 1131b0a4af ("dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Trivial fix to spelling mistake in dev_err error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation fails then disable the memcpy support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.
Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":
INITD -------- ------------
|____________________|
_______________________ _______________
NDA @desc2 \/ @desc3
_______________________/\_______________
__________ ___________ _______________
CUBC 0 \/ MAX desc1 \/ MAX desc2
__________/\___________/\_______________
| | | |
Events:(1)(2) (3)(4)
(1) check_nda = @desc2
(2) initd = 1
(3) cur_ubc = MAX desc1
(4) cur_nda = @desc2
This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.
This error leads to incorrect residue computation.
Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.
Fixes: 53398f4888 ("dmaengine: at_xdmac: fix residue corruption")
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MediaTek High-Speed DMA controller (HSDMA) on MT7622 and MT7623 SoC has
a single ring is dedicated to memory-to-memory transfer through ring based
descriptor management.
Even though there is only one physical ring available inside HSDMA, the
driver can be easily extended to the support of multiple virtual channels
processing simultaneously by means of DMA_VIRTUAL_CHANNELS effort.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bitfield dma_inuse is allocated of size dma_requests bits, thus a
valid bit address is from 0 to (dma_requests - 1).
When find_first_zero_bit() fails, it returns dma_requests as invalid
address.
Using such address for the following set_bit() is incorrect and, if
dma_requests is a multiple of BITS_PER_LONG, it will cause a buffer
overflow.
Currently this driver is only used in DT stm32h743.dtsi where a safe value
dma_requests=16 is not triggering the buffer overflow.
Fixed by checking the return value of find_first_zero_bit() _before_
using it.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the DW AXI DMAC controller.
DW AXI DMAC is a part of HSDK development board from Synopsys.
In this driver implementation only DMA_MEMCPY transfers are
supported.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.
With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add a spinlock and a 'enabled' boolean on channel descriptor, to avoid
using buffer descriptors in the interrupt context,
when sdma_disable_channel is called meanwhile.
Signed-off-by: Thierry Bultel <tbultel@pixelsurmer.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that a race condition happens between a client
driver and the rcar-dmac driver:
- The rcar_dmac_isr_transfer_end() is called.
- The done list appears, and desc.running is the next active list.
- rcar_dmac_chan_get_residue() is called by a client driver before
rcar_dmac_isr_channel_thread() is called.
- The rcar_dmac_chan_get_residue() will not find any descriptors.
- And, the following WARNING happens:
WARN(1, "No descriptor for cookie!");
The sh-sci driver with HSCIF (921,600bps) on R-Car H3 can cause this
situation.
So, this patch checks the done lists in rcar_dmac_chan_get_residue()
and returns zero if the done lists has the argument cookie.
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remotely controlled BAM instance should not do any power management from
CPU side, as cpu can not reliably say if the BAM is busy or not.
Disable it for such instances.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BAM_DESC_CNT_TRSHLD register is global register, which can only be written
when BAM is in master mode, So check the mode of operation before writing
it.
Without this check SOC's xPU would catch such access and crash the system.
First noticed on DB820c while testing SLIMBus BAM.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When Linux is master of BAM, it can directly read registers to know number
of supported channels, however when its remotely controlled reading these
registers would trigger a crash if the BAM is not yet initialized or
powered up on the remote side.
This patch allows driver to read num-channels and num-ees from Device Tree
for remotely controlled BAM.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When BAM is remotely controlled it does not sound correct to control
its clk on Linux side. Make it optional, so that its not mandatory
for remote controlled BAM instances.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Existing option noverify disables both random src/dst address offset
setup and data verification. Sometimes, we need to control random
src/dst address setup and verification separately, such as disabling
random to make sure that test covers addresses in all interleaving
banks, but data verification is still performed.
This patch adds option norandom to disable random offset setup. Option
noverify has been changed to disable data verification only.
Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull ARM updates from Russell King:
- StrongARM SA1111 updates to modernise and remove cruft
- Add StrongARM gpio drivers for board GPIOs
- Verify size of zImage is what we expect to avoid issues with
appended DTB
- nommu updates from Vladimir Murzin
- page table read-write-execute checking from Jinbum Park
- Broadcom Brahma-B15 cache updates from Florian Fainelli
- Avoid failure with kprobes test caused by inappropriately
placed kprobes
- Remove __memzero optimisation (which was incorrectly being
used directly by some drivers)
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8745/1: get rid of __memzero()
ARM: 8744/1: don't discard memblock for kexec
ARM: 8743/1: bL_switcher: add MODULE_LICENSE tag
ARM: 8742/1: Always use REFCOUNT_FULL
ARM: 8741/1: B15: fix unused label warnings
ARM: 8740/1: NOMMU: Make sure we do not hold stale data in mem[] array
ARM: 8739/1: NOMMU: Setup VBAR/Hivecs for secondaries cores
ARM: 8738/1: Disable CONFIG_DEBUG_VIRTUAL for NOMMU
ARM: 8737/1: mm: dump: add checking for writable and executable
ARM: 8736/1: mm: dump: make the page table dumping seq_file
ARM: 8735/1: mm: dump: make page table dumping reusable
ARM: sa1100/neponset: add GPIO drivers for control and modem registers
ARM: sa1100/assabet: add BCR/BSR GPIO driver
ARM: 8734/1: mm: idmap: Mark variables as ro_after_init
ARM: 8733/1: hw_breakpoint: Mark variables as __ro_after_init
ARM: 8732/1: NOMMU: Allow userspace to access background MPU region
ARM: 8727/1: MAINTAINERS: Update brcmstb entries to cover B15 code
ARM: 8728/1: B15: Register reboot notifier for KEXEC
ARM: 8730/1: B15: Add suspend/resume hooks
ARM: 8726/1: B15: Add CPU hotplug awareness
...
This cycle we have small update for:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- Add support for race free transfer termination and updating
for users for that
- Support for new rev of hidma with addition new APIs to
get device match data in ACPI/OF
- Random updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7bH/
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time is smallish update with updates mainly to drivers:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- add support for race free transfer termination and updating for
users for that
- support for new rev of hidma with addition new APIs to get device
match data in ACPI/OF
- random updates to bunch of other drivers"
* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
dmaengine: dmatest: fix container_of member in dmatest_callback
dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
dmaengine: qcom_hidma: simplify DT resource parsing
dmaengine: xilinx_dma: Free BD consistent memory
dmaengine: xilinx_dma: Fix warning variable prev set but not used
dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
dmaengine: doc: format struct fields using monospace
dmaengine: doc: fix bullet list formatting
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
dmaengine: cppi41: Fix channel queues array size check
dmaengine: imx-sdma: Add MODULE_FIRMWARE
dmaengine: xilinx_dma: Fix typos
dmaengine: xilinx_dma: Differentiate probe based on the ip type
dmaengine: xilinx_dma: fix style issues from checkpatch
dmaengine: xilinx_dma: Fix kernel doc warnings
dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
dmaengine: zynqmp_dma: Fix race condition in the probe
...
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
The type of arg passed to dmatest_callback is struct dmatest_done.
It refers to test_done in struct dmatest_thread, not done_wait.
Fixes: 6f6a23a213 ("dmaengine: dmatest: move callback wait ...")
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Acked-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The __memzero assembly code is almost identical to memset's except for
two orr instructions. The runtime performance of __memset(p, n) and
memset(p, 0, n) is accordingly almost identical.
However, the memset() macro used to guard against a zero length and to
call __memzero at compile time when the fill value is a constant zero
interferes with compiler optimizations.
Arnd found tha the test against a zero length brings up some new
warnings with gcc v8:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82103
And successively rremoving the test against a zero length and the call
to __memzero optimization produces the following kernel sizes for
defconfig with gcc 6:
text data bss dec hex filename
12248142 6278960 413588 18940690 1210312 vmlinux.orig
12244474 6278960 413588 18937022 120f4be vmlinux.no_zero_test
12239160 6278960 413588 18931708 120dffc vmlinux.no_memzero
So it is probably not worth keeping __memzero around given that the
compiler can do a better job at inlining trivial memset(p,0,n) on its
own. And the memset code already handles a zero length just fine.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
