I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in
commit 66e3d5c099
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 16 21:24:16 2013 +0200
drm/i915: move i9xx dpll enabling into crtc enable function
that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:
"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."
Fix this regression up.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With updates to the spec, we can actually see the context layout, and
how many dwords are allocated. That table suggests we need 70720 bytes
per HW context. Rounded up, this is 18 pages. Looking at what lives
after the current 4 pages we use, I can't see too much important (mostly
it's d3d related), but there are a couple of things which look scary. I
am hopeful this can explain some of our odd HSW failures.
v2: Make the context only 17 pages. The power context space isn't used
ever, and execlists aren't used in our driver, making the actual total
66944 bytes.
v3: Add a comment to the code. (Jesse & Paulo)
Reported-by: "Azad, Vinit" <vinit.azad@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which
caused the sprites to not work at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously only setting the WM_PIPE registers, now we are
setting the LP watermark registers. This should allow deeper PC
states, resulting in power savings.
We're only using 1/2 data buffer partitioning for now.
v2: Merge both hsw_compute_pri_wm_* functions (Ville)
v3: - Simplify hsw_compute_wm_results (Ville)
- Rebase due to changes on the previous patch
v4: Unconfuse wm_lp/level (Ville)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously calling sandybridge_update_wm on HSW, but the SNB
function didn't really match the HSW specification, so we were just
writing the wrong values.
With this patch, the haswell_update_wm function will set the correct
values for the WM_PIPE registers, but it will still keep all the LP
watermarks disabled.
The patch may look a little bit over-complicated for now, but it's
because much of the infrastructure for setting the LP watermarks is
already in place, so we won't have too much code churn on the patch
that sets the LP watermarks.
v2: - Fix pixel_rate on panel fitter case (Ville)
- Try to not overflow (Ville)
- Remove useless variable (Ville)
- Fix p->pri_horiz_pixels (Paulo)
v3: - Fix rounding errors on hsw_wm_method2 (Ville)
v4: - Fix memcmp bug (Paulo)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add set_seqno which didn't exist before rebase (Haihao)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like the other rings, the VECS supports semaphores. The semaphore stuff
is a bit wonky so this patch on it's own should be nice for review.
This patch should have no functional impact.
v2: Fix the English parts of clarification (again, register names were
right, text was reversed) (Damien)
Restore the still valid invariant. (Damien)
The bsd semaphore register should be MI_SEMAPHORE_SYNC_VVE (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaces the existing MBOX update code with a more generalized
calculation for emitting mbox updates. We also create a sentinel for
doing the updates so we can more abstractly deal with the rings.
When doing MBOX updates the code must be aware of the /other/ rings.
Until now the platforms which supported semaphores had a fixed number of
rings and so it made sense for the code to be very specialized
(hardcoded).
The patch does contain a functional change, but should have no
behavioral changes.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphores are tied very closely to the rings in the GPU. Trivial patch
adds comments to the existing code so that when we add new rings we can
include comments there as well. It also helps distinguish the ring to
semaphore mailbox interactions by using the ringname in the semaphore
data structures.
This patch should have no functional impact.
v2: The English parts (as opposed to register names) of the comments
were reversed. (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the intel_dpio_{read,write} and valleyview_{punit,nc}_{read,write}
use the IOSF sideband interface. They access the same registers and do
mostly the same stuff, but no shared code. There are even duplicate
register defines for the same registers. Both have locking, but the
former use dpio_lock and the latter rps.hw_lock. It's racy.
This patch refactors the sideband access to a single function that
expects dpio_lock to be held. The dpio_lock is only used for sideband
stuff, so it's a better match than rps.hw_lock for the purpose. The rps
stuff still needs rps.hw_lock, since it's used to protect more than just
the register access, so rps code will need to hold both locks.
Based on the work by Shobhit Kumar <shobhit.kumar@intel.com> and Yogesh
Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1544d9d573 added a workaround
inside haswell_init_clock_gating and mentioned it is "a workaround for
early silicon revisions and should be removed later". This workaround
is documented in bit 31 of PRI_CTL. I asked Arthur and he mentioned
that setting FORCE_ARB_IDLE_PLANES replaces that workaround for the
newer machines. So use the new one.
Also notice that there's still another workaround for PRI_CTL that
involves WM_DBG, but it's not the one we're reverting. And notice that
we were previously setting WM_DBG_DISALLOW_MULTIPIPE_LP which disables
the LP watermarks when more than one pipe is used, and we really don't
want this because we need the LP watermarks if we want to reach deeper
PC states.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a comment for the w/a name Ville dug out of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 46500h bit 23 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
v2: Ville suggested to enable it back when disabling fbc to avoid wasting
power.
v3: RMW to preserve other bits (by Ville)
v4: Fix from Ville: sed &/| at RMW
v5: Too far on sed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Insert missing space that checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 420B0h bit 22 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduce Frame Buffer Compression (FBC) support for IVB,
without enabling it by default.
It adds a new function gen7_enable_fbc to avoid getting
ironlake_enable_fbc messed with many IS_IVYBRIDGE checks.
v2: Fixes from Ville.
* Fix Plane. FBC is tied to primary plane A in HSW
* Fix DPFC initial write to avoid let trash on the register.
v3: Checking for bad plane on intel_update_fbc() as Chris suggested.
v4: Ville pointed out that according to BSpec FBC_CTL bits 0:3 must be 0.
v5: Up to v4 this work was entirely focused on Haswell. However Ville
noticed I could reuse the FBC work done for HSW and get FBC for free
at Ivybridge. So it makes more sense enable FBC for IVB first.
FBC for HSW comming on next patches. We are just not enabling it by
default on IVB.
v6: Fix confused commit name (by Matt Turner).
v7: Remove gtt_offset shift since it is page aligned byte offset (by Ville).
Cc: Matt Turner <mattst88@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
But we need to get the right stolen base and make pre-allocated objects
for BIOS stuff so we don't clobber it. If the BIOS hasn't allocated a
power context, we allocate one here too, from stolen space as required
by the docs.
v2: fix stolen to phys if ladder (Ben)
keep BIOS reserved space out of allocator altogether (Ben)
v3: fix mask of stolen base (Ben)
v4: clean up preallocated object on unload (Ben)
don't zero reg on unload (Jesse)
fix mask harder (Jesse)
v5: use unref for freeing stolen bits (Chris)
move alloc/free to intel_pm.c (Chris)
v6: NULL pctx at disable time so error paths work (Ben)
v7: use correct PCI device for config read (Jesse)
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 03752f5b7b.
This revert requires a bit of explanation on how I understand things
work. Internally the architects/designers decide how the stolen encoding
works. We put it in a doc. BIOS writers take these docs and implement
it. Driver writers read the doc too, and read the value left by the BIOS
writers, and then we make magic.
The failing here is that in the docs we had[1] contained two different
definitions for this register for Gen7. (We have both a PCI register,
and an MMIO, and each of these were different). At the time [2] of
03752f5, we asked the architects what the correct value should be; but
that doesn't match the reality (BIOS) unfortunately.
So on all machines I can get my hands on, this revert is the right thing
to do. I've also worked with the product group to confirm that they
agree this revert is what we should do. People using HW made my "people"
who both write their own BIOS, and have access to our docs (Apple?).
Investigations are still ongoing about whether we need to add a list
of machines needing special handling, but this patch should be the
right thing for pretty much everyone.
[1] The docs are still wrong on this one. Now instead of two registers with
two definitions, we have one register with BOTH definitions, progress?
[2] The open source PRMs have the "wrong" definitions in chapter Volume
1 part6, section 1.1.12.
This digging was inspired by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Augment the patch saying that it's still a bit unclear
whether there are any machines out there with "wrong" firmware and
whether we need to add a list to handle them specially.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- PCH_ prefix for pch registers on ibx/cpt/ppt.
- Drop the DP_ from the link defines, redundant.
- Drop the GMCH from the data defines and instead give the special g4x
registers a consistent _G4X postfix.
v2:
- Realign #defines and use tabs (Paulo).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it, also extract a common helper to copy the timings from the
cpu transcoder to the pch transcoder. That way it's really explicit
how the lpt transcoder is hardcoded.
v2:
- Re-align #defines properly (Paulo).
- Use cpu_transcoder when copying pipe timings (Paulo).
- s/intel_pch_transcoder_enable/intel_pch_transcoder_set_timings/
since we already have a pch transcoder enable function, and this is
clearer, too.
- Fixup 80 char line overflow in intel_display.c. I've opted to ignore
this in i915_reg.h and i915_ums.c since meh.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every time I read hsw code I get completely confused about this. So
call it what it is more explicitly.
Also, add an LPT_TRANSCONF for the pch transcoder A and use it in
lpt-only code, to really unconfuse me.
v2: s/plane/pipe/ in the TRANSCONF #define (Paulo).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever leak a non-DP compliant port width through here, we have a
pretty serious issue. So just rip out all these WARNs - if we need
them it's probably better to have them at a central place where we
compute the dp lane count.
Also use the new DDI width macro for FDI mode.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixup the embarrassing s/intel_dp->DP/temp/ mistake Paulo
spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This does duplicate the logic in intel_crtc_mode_get a bit, but the
issue is that we also should handle interlace modes and other insanity
correctly.
Hence I've opted for a sligthly more elaborate route where we first
read out the crtc timings for the adjusted mode, and then optionally
(not sure if we really need it) compute the modeline from that.
v2: Also read out the pipe source dimensions into the requested mode.
v3: Rebase on top of the moved cpu_transcoder.
v4: Simplify CHECK_FLAGS logic as suggested by Chris Wilson. Also
properly #undef that macro again.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (v3)
[danvet: Use the existing mask for interlaced bits, spotted by Mika.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the fdi m/n values to easily compute the adjusted mode
dotclock on pch ports. Hence make sure the values stored in the pipe
config are always reliable.
v2: Fixup FDI TU readout.
v3: Rebase on top of moved cpu_transcoder.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.
v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Make TRANSCODER_EDP handling more explicit. (Imre)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS uses power of two values for the data/link N value.
Follow suit to make the Zotac DP to dual-HDMI dongle work.
v2: Clean up the magic numbers and defines
Change the N clamping to be a bit easier on the eye
Rename intel_reduce_ratio to intel_reduce_m_n_ratio
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59810
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shame on me for not putting the bit definitions next to the register
definition in the first place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is bad news and shouldn't be happening.
V2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stolen from a patch with the below impressive sob-section.
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop everything but the header #defines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits 30 and 24:0 are PBC, so don't zero them. Some of the other bits
are being zeroed, but I couldn't find a reason for this, so leave them
as they are for now to avoid regressions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Delete the redudant #define that Imre spotted in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec contains several scattered notes which state that the maximum
fence stride was increased to 256KB on IVB.
Testing on real hardware agrees.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB and HSW use different encodings for the PPGTT cacheability bits in
the GAM_ECOCHK register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GAC_ECO_BITS has a bit similar to GAM_ECOCHK's ECOCHK_SNB_BIT. Add
the define, and enable it on SNB.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting this, but in case it doesn't...
v2: Define the bits we actually want to clear (Jesse)
Make it an RMW op (Jesse)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Slightly different than other platforms.
v2 [Jani]: Fix IOSF_BYTE_ENABLES_SHIFT shift. Use common routine.
v3: drop turbo defines from this patch (Ville)
use PCI_DEVFN(2,0) instead of open coding (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add checkpatch bikeshed about missing space.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Earlier code would leave both bits set, so any reset after the first
would only reset media.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now with Egbert Eich's hpd infrastructure rework merged this is dead
simple. And we need this to make output detection work on SDVO - with
the cleaned-up drm polling helpers outputs which claim to have hpd
support are no longer polled.
Now SDVO claims to do that, but it's not actually wired up. So just do
it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to enable HPD interrupts for individual pins to only receive
hotplug events from lines which are connected and working.
v2: Restructured initailization of const arrays following a suggstion
by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to HSW PM programming guide, frequency bits starts at
24 instead of 25.
v2: Paulo Zanoni noticed that only frequency bits can be set at
GEN6_RPNSWREQ. All others are read only.
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec mentions this for HSW+. I can't quite tell what the effects are,
and I don't easily have a way to test this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We could split this out into a separate routine at some point as an
optimization.
v2: use FORCEWAKE_KERNEL (Ville)
Note: Ville mentioned in his review that he declines to be responsible
if this blows up due to the lack of "readback a register != FW_ACK,
but from the same cacheline" magic we have in other forcewake
implementations.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Bikeshed overtly long lines according to checkpatch.pl. Nope,
this time around I didn't screw up printk message since I've left
those alone.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set the 'allow force wake' bit to enable forcewake handling
later on.
v2: split from clock gating patch (Jani)
check for allowwakeack (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable bits for ADPA HSYNC and VSYNC where mixed up resulting in suspend
becoming standby and vice versa. Fixed by swapping their bit position.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits used only on HDMI mode now have HDMI_ prefix instead of SDVO_.
The COLOR_FORMAT bits now have prefixes (and the 12bpc bit is for HDMI
only).
Notice that this patch uncovers a bug on the SDVO code: the
COLOR_RANGE_16_235 bit can only be used if the port is in TMDS mode,
not SDVO mode. This will have to be fixed in a later patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since they're all the same register, leave all the #defines at the
same place, organized by Gen and also specify which bits are used by
only a specific port or encoding.
Also remove a few unused duplicates and adjust indentation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some HDMI registers can be used for SDVO, so saying "HDMIB" should be
the same as saying "SDVOB" for a given HW generation. This was not
true and led to confusions and even a regression.
Previously we had:
- SDVO{B,C} defined as the Gen3+ registers
- HDMI{B,C,D} and PCH_SDVOB defined as the PCH registers
But now:
- SDVO{B,C} became GEN3_SDVO{B,C} on SDVO code
- SDVO{B,C} became GEN4_HDMI{B,C} on HDMI code
- HDMI{B,C,D} became PCH_HDMI{B,C,D}
- PCH_SDVOB is still the same thing
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While old platforms had 3 transcoders and 3 pipes (1:1), HSW has
4 transcoders and 3 pipes.
These regs were being used only by HDMI code where pipe is always the same
thing as cpu_transcoder.
This patch allow us to use them for DP, specially for TRANSCODER_EDP.
v2: Adding HSW_TVIDEO_DIP_VSC_DATA to transmit vsc to eDP.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The indentation is getting way too deep. Pull the vblank interupt
handling out to separate functions.
v2: Keep flip_mask handling in the main irq handler and
flatten {i8xx,i915}_handle_vblank() even further.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We plan to treat GEN7_ERR_INT as an interrupt, so use this register
for the checks inside I915_WRITE. This way we can have the best of
both worlds: the error message with a register address and the
V2: Split in 2 patches: one for the macro, one for changing the
register, as requested by Ben.
V3: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW no longer has the PIPECONF bit for limited range RGB output.
Instead the pipe CSC unit must be used to perform that task.
The CSC pre offset are set to 0, since the incoming data is full
[0:255] range RGB, the coefficients are programmed to compress the
data into [0:219] range, and then we use either the CSC_MODE black
screen offset bit, or the CSC post offsets to shift the data to
the correct [16:235] range.
Also have to change the confiuration of all planes so that the
data is sent through the pipe CSC unit. For simplicity send the
plane data through the pipe CSC unit always, and in case full
range output is requested, the pipe CSC unit is set up with an
identity transform to pass the plane data through unchanged.
I've been told by some hardware people that the use of the pipe
CSC unit shouldn't result in any measurable increase in power
consumption numbers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bit controlling whether PIPE_CONTROL DW/QW write targets
the global GTT or PPGTT moved moved from DW 2 bit 2 to
DW 1 bit 24 on IVB.
I verified on IVB that the fix is in fact effective. Without the fix
none of the scratch writes actually landed in the pipe control page.
With the fix the writes show up correctly.
v2: move PIPE_CONTROL_GLOBAL_GTT_IVB setup to where other flags are set
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to:
commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Dec 11 15:18:28 2012 +0000
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.
We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.
There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some early bios versions seem to ship with the wrong tuning values for
the MCH, possible resulting in pipe underruns under load. Especially
on DP outputs this can lead to black screen, since DP really doesn't
like an occasional whack from an underrun.
Unfortunately the registers seem to be locked after boot, so the only
thing we can do is politely point out issues and suggest a BIOS
upgrade.
Arthur Runyan pointed us at this issue while discussion DP bugs - thus
far no confirmation from a bug report yet that it helps. But at least
some of my machines here have wrong values, so this might be useful in
understanding bug reports.
v2: After a bit more discussion with Art and Ben we've decided to only
the check the watermark values, since the OREF ones could be be a
notch more aggressive on certain machines.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're physically the same pins and also the same bits, duplicating
only confuses the reader. This also makes it a bit obvious that we
have quite some code duplication going on here. Squashing that is for
a larger rework in our hpd handling though.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RC6 VIDS has a linear ramp starting at 250mv, which means any values
below 250 are invalid. The old buggy macros tried to adjust for this to
be more flexible, but there is no need. As Dan pointed out the ENCODE
only ever has one value. The only invalid value for decode is an input
of 0 which means something is really wonky, and the cases where DECODE
are used either don't matter (debug values), or would be implicitly
correct (the check for less than 450).
This patch makes simpler, easier to read macros which are actually
correct. Maybe this patch can actually fix some bugs now.
Thanks to Dan for catching this. /me hides
Cc: stable@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
The VGACNTRL register has moved around between different platforms.
To handle the differences add i915_vgacntrl_reg() which returns the
correct offset for the VGACNTRL register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The shift changed, hurray.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implements WaVSRefCountFullforceMissDisable as documented in the BSpec
3D workarounds chapter.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was wrong in many different ways, so this is a full
rewrite. We don't have "different power wells for different parts of
the GPU", we have a single power well, but we have multiple registers
that can be used to request enabling/disabling the power well. So
let's be a good citizen and only use the register we're suppose to
use, except when we're loading the driver, where we clear the request
made by the BIOS.
If any of the registers is requesting the power well to be enabled, it
will be enabled. If none of the registers is requesting the power well
to be enabled, it will be disabled.
For now we're just forcing the power well to be enabled, but in the
next commits we'll change this.
V2:
- Remove debug messages that could be misleading due to possible
race conditions with KVMr, Debug and BIOS.
- Don't wait on disabling: after a conversaion with a hardware
engineer we discovered that the "restriction" on bit 31 is just
for the "enable" case, and we don't even need to wait on the
"disable" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SR01 needs to be touched to disable VGA on non-UMS setups too.
So the sequencer registers need to include the appripriate offset
on VLV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Dropped the clock gating registers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of 0x18xxxx use (VLV_DISPLAY_BASE + xxxx).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of 0x18xxxx use (VLV_DISPLAY_BASE + xxxx).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CURSIZE is not present on VLV, so it was left out, as were the IVB
specific cursor B registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a required workarounds for all products, especially on gen6+
where it causes the command streamer to fail to parse instructions
following a WAIT_FOR_EVENT. We use WAIT_FOR_EVENT for synchronising
between the GPU and the display engines, and so this bit being unset may
cause hangs.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52311
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RGB color range select bit on the DP/SDVO/HDMI registers
disappeared when PCH was introduced, and instead a new PIPECONF bit
was added that performs the same function.
Add a new INTEL_MODE_LIMITED_COLOR_RANGE private mode flag, and set
it in the encoder mode_fixup if limited color range is requested.
Set the the PIPECONF bit 13 based on the flag.
Experimentation showed that simply toggling the bit while the pipe is
active doesn't work. We need to restart the pipe, which luckily already
happens.
The DP/SDVO/HDMI bit 8 is marked MBZ in the docs, so avoid setting it,
although it doesn't seem to do any harm in practice.
TODO:
- the PIPECONF bit too seems to have disappeared from HSW. Need a
volunteer to test if it's just a documentation issue or if it's really
gone. If the bit is gone and no easy replacement is found, then I suppose
we may need to use the pipe CSC unit to perform the range compression.
v2: Use mode private_flags instead of intel_encoder virtual functions
v3: Moved the intel_dp color_range handling after bpc check to help
later patches
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix up some copypaste errors in the PIPESTAT register for VLV.
SPRITE0_FLIP_DONE_INT_EN_VLV is bit 22, not bit 26.
SPRITE0_FLIPDONE_INT_STATUS_VLV is bit 14, not bit 15.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
These are useful for investigating hangs involving WAIT_FOR_EVENT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Apply a droplet of Future-Proof in the if-ladder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm not really sure, since the w/a entry is as thin on details as
ever, and Bspec doesn't say anything about it. But I've figured only
dispatching to rows 0&1 instead of all four should be the right thing
for GT1.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add the missing snb server GT1 to the check, spotted by Chris
Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Quoting from Bspec, 3D_CHICKEN1, bit 10
This bit needs to be set always to "1", Project: DevSNB "
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ilk+ somehow used #defines in near the PIPESTAT definitions, which
decently confused me. Earlier platforms called it BPP instead of
BPC. Clean this all up.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those status bits don't follow the usual pattern: _MASK (those bits are
write 1 to clear, useful to select the value we want to read) and the
values shifted by the same amount.
Cleaned that that up when poking at the register for testing purposes,
might as well upstream that cleanup.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we fail to set the bit when needed we get some nice FDI link
training failures (AKA "black screen on VGA output").
While we don't really know how to properly choose whether we need to
set the bit or not (VBT?), just read the initial value set by the BIOS
and store it for later usage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this code to init the PCH SSC refclk and the FDI registers.
The BIOS does this too and that's why VGA worked before this patch,
until you tried to suspend the machine...
This patch implements the "Sequence to enable CLKOUT_DP for FDI usage
and configure PCH FDI/IO" from our documentation.
v2:
- Squash Damien Lespiau's reset spelling fix on top.
- Add a comment that we don't need to bother about the ULT special
case Damien noticed, since ULT won't have VGA.
- Add a comment to rip out the SDV codepaths once haswell ships for
real.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we should be able to write mPHY registers using the Sideband
Interface in the next commit. Also fixed some syntax oddities in the
related code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TRANS_DP_VIDEO_AUDIO is not used at all.
The other 3 has duplicated #defines.
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow a chunk of unused register defines ended up in the middle of
the PLL defines. They go back to the original kms merging.
The only used #define is SR01, move it to the register name together
with the other legacy vga stuff.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I actually found this problem on Haswell, but then discovered Ivy
Bridge also has it by reading the spec.
I don't have the hardware to test this.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDI A and E have 4 lanes to share, so if DDI A is using 4 lanes,
there's nothing left for DDI E, which means there's no CRT port on the
machine.
The bit we're checking here is programmed at system boot and it cannot
be changed afterwards, so we cannot change the amount of lanes
reserved for each DDI port.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to enable a special bit, otherwise none of the DP functions
requiring the PCH will work.
Version 2: store the PCH ID inside dev_priv, as suggested by Daniel
Vetter.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's pretty much all consolidated now that we've killed AGP. We can move
the one outlier, and defines too.
(Kill some unused defines in the process)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to map the PTEs WC. I've not done thorough testing or
performance measurements with this patch, but it should be decent.
This is based on a patch from Jesse with the original commit message
> I've only lightly tested this so far, but the corruption seems to be
> gone if I write the GFX_FLSH_CNTL reg after binding an object. This
> register should control the TLB for the system agent, which is what CPU
> mapped objects will go through.
It has been updated for the new AGP-less code by me, and included with
it is feedback from the original patch.
v2: Updated to reflect paranoia on pte updates/register posting reads.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v1]: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This bug existed in the old code, but was easier to fix here in the
rework. Unfortunately gen7 doesn't have a nice way to figure out the
size and we must use a lookup table.
As Jesse pointed out, there is some confusion in the docs about these
definitions. We're picking the one which seems more accurate, but we
really aren't certain.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a quick hack we make the old intel_gtt structure mutable so we can
fool a bunch of the existing code which depends on elements in that data
structure. We can/should try to remove this in a subsequent patch.
This should preserve the old gtt init behavior which upon writing these
patches seems incorrect. The next patch will fix these things.
The one exception is VLV which doesn't have the preserved flush control
write behavior. Since we want to do that for all GEN6+ stuff, we'll
handle that in a later patch. Mainstream VLV support doesn't actually
exist yet anyway.
v2: Update the comment to remove the "voodoo"
Check that the last pte written matches what we readback
v3: actually kill cache_level_to_agp_type since most of the flags will
disappear in an upcoming patch
v4: v3 was actually not what we wanted (Daniel)
Make the ggtt bind assertions better and stricter (Chris)
Fix some uncaught errors at gtt init (Chris)
Some other random stuff that Chris wanted
v5: check for i==0 in gen6_ggtt_bind_object to shut up gcc (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v4]: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Make the cache_level -> agp_flags conversion for pre-gen6 a
tad more robust by mapping everything != CACHE_NONE to the cached agp
flag - we have a 1:1 uncached mapping, but different modes of
cacheable (at least on later generations). Suggested by Chris Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So store into the scratch space of the HWS to make sure the invalidate
occurs.
v2: use GTT address space for store, clean up #defines (Chris)
v3: use correct #define in blt ring flush (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/1063252
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround for dual port PS dispatch on GT1.
v2: pull in register definition & offset handling
v3: use IVB GT1 macro to get the right regs (Ben)
v4: add for VLV too (Ben)
v5: don't read the reg, it's masked so we'll only enable the one extra bit (Chris)
v6: use a _GT2 suffix for the second reg (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to get the right vblank interrupt frequency.
v2: pull in register definition
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needs to be set on every context restore as well, so set it as part of
the initial state so we can save/restore it. Note this removes the IVB
workaround value from VLV and uses the default value, just adding in the
L3 cache aging disable bit, since the IVB value is wrong for VLV.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.
This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.
Problems we fixed:
1 - Train Haswell FDI at the right time.
We need to train the FDI before enabling the pipes and planes, so
we're moving the call from lpt_pch_enable to haswell_crtc_enable
directly.
We are also removing ironlake_fdi_pll_enable since the PLL
enablement on Haswell is completely different and is also done
during the link training steps.
2 - Use the right FDI_RX_CTL register on Haswell
There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
Using "pipe" here is wrong.
3 - Don't rely on DDI_BUF_CTL previous values
Just set the bits we want, everything else is zero. Also
POSTING_READ the register before sleeping.
4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train
According to the mode set sequence documentation, this is the
right place. According to the FDI_RX_TUSIZE register description,
this is the value we should set.
Also remove the code that sets this register from the old
location: lpt_pch_enable.
5 - Properly program FDI_RX_MISC pwrdn lane values on HSW
6 - Wait only 35us for the FDI link training
First we wait 30us for the FDI receiver lane calibration, then we
wait 5us for the FDI auto training time.
7 - Remove an useless indentation level on hsw_fdi_link_train
We already "break" when the link training succeeds.
8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE
When we fail the training.
9 - Change Haswell FDI link training error messages
We shouldn't call DRM_ERROR when still looping through voltage
levels since this is expected and not really a failure. So in this
commit we adjust the error path to only DRM_ERROR when we really
fail after trying everything.
While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
it's what we use everywhere.
10 - Try each voltage twice at hsw_fdi_link_train
Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
the 80 char limit ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found in Bspec vol4h South Display Engine Registers [CPT, PPT],
section "5.3.1 TRANS_CHICKEN_1—Transcoder Chicken Bits 1"
v2: Make it compile.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set the timing override chicken bit after fdi link training
has completed and before we enable the transcoder. We also have to
clear that bit again after disabling the pch transcoder.
See "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" and "Graphics BSpec: vol4h South Display
Engine Registers [CPT, PPT], South Display Engine Transcoder and FDI
Control, Transcoder Debug and DFT, TRANS_CHICKEN_2" bit 31:
"Workaround : Enable the override prior to enabling the transcoder.
Disable the override after disabling the transcoder."
While at it, use the _PIPE macro for the other TRANS_DP register.
v2: Keep the w/a as-is, but kill the original (but wrongly placed)
workaround introduced in
commit 3bcf603f6d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jul 27 11:51:40 2011 -0700
drm/i915: apply timing generator bug workaround on CPT and PPT
and
commit d4270e57ef
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Oct 11 10:43:02 2011 -0700
drm/i915: export a CPT mode set verification function
Note that this old code has unconditionally set the w/a, which might
explain why fdi link training sometimes silently fails, and especially
why the auto-train did not seem to work properly.
v3: Paulo Zanoni pointed out that this workaround is also required on
the LPT PCH. And Arthur Ranyan confirmed that this workaround is
requierd for all ports on the pch, not just DP: The important part
is that the bit is set whenever the pch transcoder is enabled, and
that it is _not_ set while the fdi link is trained. It is also
important that the pch transcoder is fully disabled, i.e. we have to
wait for bit 30 to clear before clearing the w/a bit.
Hence move to workaround into enable/disable_transcoder, where the pch
transcoder gets enabled/disabled.
v4: Whitespace changes dropped.
v5: Don't run the w/a on IBX, we only need it on CPT/PPT and LPT.
v6:
- resolve conflicts with Paulo's big hsw vga rework
- s/!IBX/CPT since hsw paths are now all separate, and Paulo's patch
to implement the equivalent w/a for LPT is already merged.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v5)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix support for all RGB/BGR pixel formats (except the 16:16:16:16 float
format).
Fix intel_init_framebuffer() to match hardware and driver limitations:
* RGB332 is not supported at all
* CI8 is supported
* XRGB1555 & co. are supported on Gen3 and earlier
* XRGB210101010 & co. are supported from Gen4 onwards
* BGR formats are supported from Gen4 onwards
* YUV formats are supported from Gen5 onwards (driver limitation)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment says for eaglelake/cantiga, but it's listed in the ilk table,
too. So apply it to both.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW consolidates SPRTILEOFF and SPRLINOFF into a single SPROFFSET
register.
v2: Remove a useless level of indentation (Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And properly toggle the chicken bit in the pch to enable/disable fdi C
rx. If we don't set this bit correctly, the rx gets confused in link
training, which can result in an fdi link that silently fails to train
the link (since the corresponding register reports success). Note that
both fdi link B and C can suffer when this bit is not set correctly.
The code as-is has a few deficiencies:
- We presume all pipes use the pch which is not the case for cpu edp.
- We don't bother with disabling both pipes when we could make things
work, e.g. when pipe B switched from 4 to 2 lanes due to a mode
change, we don't bother updating the w/a bit.
- It's ugly.
All of these are because we compute ->fdi_lanes way too late, when
we're already setting up individual pipes. We need to have this
information in ->modeset_global_resources already, to set things up
correctly. But that is a much larger reorg of the code.
Note that we actually hit the 2 lanes limit in practice rather
quickly: Even though the 1920x1200 mode native mode of my screen fits
into 2 lanes, it needs 3 lanes for the 1920x1080 (since that somehow
has much more blanking ...). Not obeying this restriction seems to
results in cute-looking digital noise.
v2: Only ever clear the chicken bit when both pipes are off.
v3: Use the new ->modeset_global_resources callback.
v4: Move the WARNs to the right place. Oh how I hate hacks.
v5: Fix spelling, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the other registers. This one also appeared on Haswell for the
first time, so that's why we are renaming it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.
Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.
Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.
V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register appeared in Haswell. It does not have an EDP version
because the EDP transcoder is always tied to the DDIA clock. Notice
that if we call PIPE_CLK_SEL(pipe) when pipe is PIPE_A and transcoder
is TRANSCODER_EDP we might introduce a bug, that's why this is a
transcoder register even though it does not have an EDP version.
Even though Haswell names this register PIPE_CLK_SEL, it will be
renamed to TRANS_CLK_SEL in the future, so let's just start using the
real name that makes more sense and avoids misusage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).
For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.
For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.
V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.
We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.
In other words:
Imagine the following case:
xrandr --output eDP1 --auto --crtc 0
xrandr --output eDP1 --off
xrandr --output eDP1 --auto --crtc 2
After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.
So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
hw will not dtrt.
- Revert the early bail-out in case the register values are unset.
The last change reverts
commit bfa3384a9a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Apr 10 11:58:04 2012 -0700
drm/i915: check PPS regs for sanity when using eDP
v2:
- Unlock the PP regs as the very first thing. This is a required w/a
for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.
v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.
v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.
v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Register 0x42020 was defined twice under the names PCH_DSPCLK_GATE_D and
ILK_DSPCLK_GATE. This patch consolidate the 2 sets of defines in one.
The transforms done are:
PCH_DSPCLK_GATE_D -> ILK_DSPCLK_GATE_D
ILK_DSPCLK_GATE -> ILK_DSPCLK_GATE_D
DPARBUNIT_CLOCK_GATE_DISABLE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
ILK_DPARB_CLK_GATE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
DPFDUNIT_CLOCK_GATE_DISABLE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_DPFD_CLK_GATE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_CLK_FBC -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
DPFCRUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS1 -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
DPFCUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS2 -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
We have a VHRUNIT_CLOCK_GATE_DISABLE define for the pre-ILK DSPCLK_GATE_D.
Even if the same bit is used in ILK_DSPCLK_GATE_D, other bits in the
register change, so I went with re-defining it, well more precisely rename
IVB_VRHUNIT_CLK_GATE, which is not specific to IVB+. So:
IVB_VRHUNIT_CLK_GATE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE
VHRUNIT_CLOCK_GATE_DISABLE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE (ILK+ code)
This commit is only a renaming commit, further commits will clean up the
logic.
v2: Rename bit 5 and 7 to _ENABLE as setting them to 1 enables clock
gating on their respective units, contrary to all of the other bits
(Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
