Add mt6397 support using mediatek common pinctrl driver.
mt6397 is a PMIC, and pinctrl/GPIO is part of 6397 chip.
Pinctrl/GPIO driver should obtain regmap from PMIC,
so adding this support to common code.
Also, mt6397 is no need to support interrupt controller,
so changing common code to skip it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Input enable and smt setting have different register,
modify code to fix it.
Several mediatek soc use similar input enable/smt setting
procedure as mt8173, some soc use generic input enable/smt
setting, some soc has no input enable/smt setting. Adding
common code to handle all those cases, so future soc driver
can use it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several mediatek soc use similar pull setting procedure as mt8173,
the pupd enable and resistance setting are in the same register.
Add common code mtk_pctrl_spec_pull_set_samereg out of spec_pull_set
in mt8173 to handle this case, so future soc driver can use it.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct mtk_desc_pin.chip, mtk_pinctrl_devdata.invser_offset
and mtk_pinctrl_devdata.chip_type are never used in code.
Remove them.
Some per-pin data are using int for pin number and offsets.
Change to short and rearrange to reduce const data size.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinfunc header file, mt8135/mt8173 relate dts will include it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since 6397 is no need to support interrupt controller,
moving interrupt controller relate property to optional list.
Also adding mt8173 and mt8127 to bindings.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the required group function map and fill it at probe using
the pin capabilities information already present in the driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixed a small typo in the Cygnus GPIO driver
Signed-off-by: Jason Uy <jasonuy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.
Changes from v4:
- Switched to using gpiochip_add_pin_range().
- Fixed up Kconfig entry.
Changes from v3:
- Addressed review comments from Ezequiel.
Changes from v2:
- Removed module stuff which would be compiled out.
Changes from v1:
- Addressed review comments from Linus.
- Changed compatible string to "img,pistachio-system-pinctrl".
- Look for GPIO sub-nodes by name.
- A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both pconf_get_pin and pconf_set_pin needs to lookup pin cap based
on the pin number. Create a common helper function that both
functions can use that also handles the case where no pin number is
found in the pins array.
This also fixes a small bug in pconf_get_pin where pconf_get_i2c0
would use the pins array index rather than the pin number.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As of commit 9d07d414d4 ("ARM: shmobile: r8a73a4: ape6evm: Remove
legacy platform"), r8a73a4 is only supported in generic ARM
multi-platform builds. Hence CONFIG_ARCH_MULTIPLATFORM is always set,
and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Regarding pin control, r8a7791 and r8a7793 are identical, so it is
sufficient to add an sh_pfc_soc_info structure to enable r8a7793 support.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The last serial port is called "SCIFB", not "SCIFAB".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Sunrisepoint-H is a desktop version of the PCH (Platform Controller
Hub). It has slightly different pin configuration compared to the LP
version. This patch adds support for Sunrisepoint-H to the existing
pinctrl-sunrisepoint.c driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As of commit 9d07d414d4 ("ARM: shmobile: r8a73a4: ape6evm: Remove
legacy platform"), r8a73a4 is only supported in generic DT-only ARM
multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old format to define pinctrl settings for imx in DT has two
hierarchy levels. The first level are function device nodes. The second
level are pingroups which contain a property fsl,pins. The original
intention was to define all pin functions in a single dtsi file and just
reference the correct ones in the board files.
This idea was rejected some time ago leading to the current design to
have all the pinfunctions defined in the board files. So we don't need
the function device nodes anymore.
This patch changes the pinctrl driver to accept devicetrees which do not
have the first hierarchy level, function device nodes. For example
karo-tx25 already has such a devicetree. Old devicetrees are still
parsed and supported.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since SCLK, MISO and MOSI are the only mandatory signals at Zynq's SPI
interfaces, SS0, SS1 and SS2 have to be configured separately as they may
be used as simple GPIO lines.
This, of course, has to be considered in the devicetree, so pin controller
configuration for e.g. an SPI0 using SS0 and SS1 only might look like the
following snippet (derived from the example of chapter "17.5.3
MIO/EMIO" Routing of Zynq-7000 TRM UG585). So MIO20 can now be used
as GPIO instead of being occupied by SPI0 SS2 function. Note the separate
pinmux function for the slave select signals:
pinctrl_spi0_default: spi0-default {
mux_spi {
function = "spi0";
groups = "spi0_0_grp";
};
mux_ss {
function = "spi0_ss";
groups = "spi0_0_ss0_grp", "spi0_0_ss1_grp";
}
conf-output {
pins = "MIO16", "MIO21";
slew-rate = <0>;
bias-disable;
low-power-disable;
io-standard = <1>;
};
conf-input {
pins = "MIO17";
slew-rate = <0>;
bias-high-impedance;
low-power-disable;
io-standard = <1>;
};
conf-select {
pins = "MIO18", "MIO19";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
pinctrl_gpio0_default {
mux {
function = "gpio0";
groups = "gpio0_20_grp"
};
conf {
pins = "MIO20";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign GPIO chip and irqchip to the GPIO container dynamically,
so we can set a unique name for each GPIO irqchip and see what
chip the hwirq offset actually relates to.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This activates strict mode muxing for the Nomadik pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While the pinmux_ops are ideally just a vtable for pin mux
calls, the "strict" setting belongs so intuitively with the
pin multiplexing that we should move it here anyway. Putting
it in the top pinctrl_desc makes no sense.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Disallow simultaneous use of the the GPIO and peripheral mux
functions by setting a flag "strict" in struct pinctrl_desc.
The blackfin pinmux and gpio controller doesn't allow user to
set up a pin for both GPIO and peripheral function. So, add flag
strict in struct pinctrl_desc to check both gpio_owner and
mux_owner before approving the pin request.
v2-changes:
- if strict flag is set, check gpio_owner and mux_onwer in if and
else clause
v3-changes:
- add kerneldoc for this struct
- augment Documentation/pinctrl.txt
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.
Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the callback for set_multiple.
As this controller has a separate set and clear register, we
can't write directly to PIO_ODSR as this would required a cached
variable and would race with at91_gpio_set.
So build masks for the PIO_SODR and PIO_CODR registers and
write them together.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for ext4 encryption which provide better security and performance.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVRsVDAAoJEPL5WVaVDYGj/UUIAI6zLGhq3I8uQLZQC22Ew2Ph
TPj6eABDuTrB/7QpAu21Dk59N70MQpsBTES6yLWWLf/eHp0gsH7gCNY/C9185vOh
tQjzw18hRH2IfPftOBrjDlPGbbBD8Gu9jAmpm5kKKOtBuSVbKQ4GeN6BTECkgwlg
U5EJHJJ5Ahl4MalODFreOE5ZrVC7FWGEpc1y/MquQ0qcGSGlNd35leK5FE2bfHWZ
M1IJfXH5RRVPUBp26uNvzEg0TtpqkigmCJUT6gOVLfSYBw+lYEbGl4lCflrJmbgt
8EZh3Q0plsDbNhMzqSvOE4RvsOZ28oMjRNbzxkAaoz/FlatWX2hrfAoI2nqRrKg=
=Unbp
-----END PGP SIGNATURE-----
Merge tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous bug fixes and some final on-disk and ABI changes
for ext4 encryption which provide better security and performance"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix growing of tiny filesystems
ext4: move check under lock scope to close a race.
ext4: fix data corruption caused by unwritten and delayed extents
ext4 crypto: remove duplicated encryption mode definitions
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
ext4 crypto: add padding to filenames before encrypting
ext4 crypto: simplify and speed up filename encryption
Pull drm fixes from Dave Airlie:
"One intel fix, one rockchip fix, and a bunch of radeon fixes for some
regressions from audio rework and vm stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915/chv: Implement WaDisableShadowRegForCpd
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/chv: Implement WaDisableShadowRegForCpd
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
This is three logical fixes (as 5 patches). The 3ware class of drivers were
causing an oops with multiqueue by tearing down the command mappings after
completing the command (where the variables in the command used to tear down
the mapping were no-longer valid). There's also a fix for the qnap iscsi
target which was choking on us sending it commands that were too long and a
fix for the reworked aha1542 allocating GFP_KERNEL under a lock.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVRkgEAAoJEDeqqVYsXL0MZbEIAL7Repky0TI1GvyYVpbJLSc+
SlJurEQ9DIpsnNtHJlEfLHicqsrK3v/xS+3Kopd1OUEIjQ0kTFPkenTiJbwFNIB+
l7D3V1EfEdnOki7F8KU5bFf3i4KWeEUZ4v/FR3PC7dz4cFRav7OrMoGaA36yT/ns
I4NFZ7iOa/6QXzfrywTDU5HbHgQYIN2MfCPy/NrVP95Yq09TkN5ulXDz/h6PD6Iy
GV/RmeckUqkdO5SZq9kkIgR/czLpVCaqpf3/G6lFdfunNkhQJ96lQTzYwbvtPBrJ
m6+sxrcCWlHzIkJsXrKtopPYzSzGdApLSsZjuYtP3RJD0uO9psfgW8pbls3dDCg=
=n4aD
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three logical fixes (as 5 patches).
The 3ware class of drivers were causing an oops with multiqueue by
tearing down the command mappings after completing the command (where
the variables in the command used to tear down the mapping were
no-longer valid). There's also a fix for the qnap iscsi target which
was choking on us sending it commands that were too long and a fix for
the reworked aha1542 allocating GFP_KERNEL under a lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: fix command completion race
3w-xxxx: fix command completion race
3w-sas: fix command completion race
aha1542: Allocate memory before taking a lock
SCSI: add 1024 max sectors black list flag
Pull slave dmaengine fixes from Vinod Koul:
"Here are the fixes in dmaengine subsystem for rc2:
- privatecnt fix for slave dma request API by Christopher
- warn fix for PM ifdef in usb-dmac by Geert
- fix hardware dependency for xgene by Jean"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: increment privatecnt when using dma_get_any_slave_channel
dmaengine: xgene: Set hardware dependency
dmaengine: usb-dmac: Protect PM-only functions to kill warning
- Build fix for SMP=n in book3s_xics.c
- Fix for Daniel's pci_controller_ops on powernv.
- Revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- Two EEH fixes from Gavin.
- Fix for CR corruption from Sam.
- Selftest build fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.
Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
-c "falloc 0 131072" \
-c "pwrite -S 0xbb 65536 2048" \
-c "fsync" /mnt/test/fff
echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d and commit f542fb.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull networking fixes from David Miller:
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.
This makes it clear that Michael is in charge. He's good, but having
me watch over his shoulder won't help.
Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Ceph RBD fix from Sage Weil.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: end I/O the entire obj_request on error
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
