- when OFA event occurs, driver will stop traffic to RAID/HBA path. Driver
waits for all the outstanding requests to complete.
- Driver sends OFA event acknowledgment to firmware.
- Driver will wait until the new firmware is up and running.
- Driver will free up the resources.
- Driver calls SIS/PQI initialization and rescans the device list.
- Driver will resume the traffic to RAID/HBA path.
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem:
- during the driver initialization, driver will poll fw
for KERNEL_UP in a 30 seconds timeout.
- if the firmware is not ready after 30 seconds,
driver will not be loaded.
Fix:
- change timeout from 30 seconds to 3 minutes.
Reported-by: Feng Li <lifeng1519@gmail.com>
Reviewed-by: Ajish Koshy <ajish.koshy@microsemi.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem:
The Linux kernel takes a logical volume offline after a LUN reset. This is
generally accompanied by this message in the dmesg output:
Device offlined - not ready after error recovery
Root Cause:
The root cause is a "quirk" in the timeout handling in the Linux SCSI
layer. The Linux kernel places a 30-second timeout on most media access
commands (reads and writes) that it send to device drivers. When a media
access command times out, the Linux kernel goes into error recovery mode
for the LUN that was the target of the command that timed out. Every
command that timed out is kept on a list inside of the Linux kernel to be
retried later. The kernel attempts to recover the command(s) that timed out
by issuing a LUN reset followed by a TEST UNIT READY. If the LUN reset and
TEST UNIT READY commands are successful, the kernel retries the command(s)
that timed out.
Each SCSI command issued by the kernel has a result field associated with
it. This field indicates the final result of the command (success or
error). When a command times out, the kernel places a value in this result
field indicating that the command timed out.
The "quirk" is that after the LUN reset and TEST UNIT READY commands are
completed, the kernel checks each command on the timed-out command list
before retrying it. If the result field is still "timed out", the kernel
treats that command as not having been successfully recovered for a
retry. If the number of commands that are in this state are greater than
two, the kernel takes the LUN offline.
Fix:
When our RAIDStack receives a LUN reset, it simply waits until all
outstanding commands complete. Generally, all of these outstanding commands
complete successfully. Therefore, the fix in the smartpqi driver is to
always set the command result field to indicate success when a request
completes successfully. This normally isn’t necessary because the result
field is always initialized to success when the command is submitted to the
driver. So when the command completes successfully, the result field is
left untouched. But in this case, the kernel changes the result field
behind the driver’s back and then expects the field to be changed by the
driver as the commands that timed-out complete.
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- fix race condition when a unit is deleted after an RLL,
and before we have gotten the LV_STATUS page of the unit.
- In this case we will get a standard inquiry, rather than
the desired page. This will result in a unit presented
which no longer exists.
- If we ask for LV_STATUS, insure we get LV_STATUS
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Ajish Koshy <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- wait on all outstanding I/O to complete before the device is removed.
- check for null device pointers in IO entry/completion functions.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Ajish Koshy <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- set pci_dev->dev to 0 only if the node is NO_NUMA_NODE.
If not, do not reset the value but retain it.
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Sagar Biradar <sagar.biradar@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- set allow_restart option during scsi_device init.
This allows the kernel to send a START/STOP Unit command to the drive if
it encounters a 4/2 check condition in sense data.
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- fix a formatting issue.
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <murthy.bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <murthy.bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- add sysfs device attributes, unique_id, lunid and path_info.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up the common code which creates a raid path request for the
controller LUNID and sends it synchronously, into a common routine;
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- allow update the luns for PTRAID devices.
Reviewed-by: Ajish Koshy <ajish.koshy@microsemi.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During slave_alloc, for logical volumes include no_write_same into the
scsi_device structure. This will insure that WRITE_SAME will not be used
for LD's.
Reviewed-by: Ajish Koshy <ajish.koshy@microsemi.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for new IUs and parsing of the Firmware Features section of the
PQI Config Table to implement the "handshake" between the driver and
firmware to communicate firmware features supported and enabled by the
driver.
Reviewed-by: Ajish Koshy <ajish.koshy@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the readl() kernel function to read all index registers. For ARM
systems, this function includes a read memory barrier that eliminates ci/pi
corruption.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Tested-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for these new device IDs:
Advantech MIC-8312BridgeB
INSPUR PM8204-2GB
INSPUR PM8204-4GB
INSPUR PM8222-SHBA
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect rare error cases for synchronous requests down the RAID path.
Also retry INQUIRY of VPD page 0 sent to an HBA drive if the command failed
due to an abort.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Decrement the active thread count after the synchronous request was
submitted to the controller but before the driver blocks to wait for the
request to complete.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas. In addition we have removed several really
old drivers: sym53c416, NCR53c406a, fdomain, fdomain_cs and removed
the old scsi_module.c initialization from all remaining drivers. Plus
an assortment of bug fixes, initialization errors and other minor
fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWsVSnSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbvbAP9ErpTZ
OR5iJ5HIz4W3Bd8aTfEpJrDyeYwSUC+sra5SKQD/ZWyVB3fYFSg+ZROyT26pmtmd
SdImhG7hLaHgVvF5qRQ=
=SQ/n
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
The PCI interrupt vectors intended to be associated with a queue may
not start at 0; a driver may allocate pre_vectors for special use. This
patch adds an offset parameter so blk-mq may find the intended affinity
mask and updates all drivers using this API accordingly.
Cc: Don Brace <don.brace@microsemi.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Skip deleting PQI operational queues when there is an error creating a
new queue group. It's not really necessary to delete the queues anyway
because they get deleted during the PQI reset that is part of the error
recovery path.
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If CONFIG_SCSI_SMARTPQI=y then don't build this driver as a module.
Signed-off-by: Steffen Weber <steffen.weber@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Don Brace <don.brace@microsemi.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: esc.storagedev@microsemi.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a small cosmetic bug in a very rarely encountered error message that
can occur when a LD has a corrupted raid map.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver's PCI IDs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS transport class will do the right thing and not register the BSG
node if now smp_handler method is present.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver’s PCI IDs to match the latest Microsemi controllers
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PQI reset to driver shutdown callback to work around controller bug.
During an 1.) OS shutdown or 2.) kexec outside of a kdump, the Linux
kernel will clear BME on our controller.
If BME is cleared during a controller/host PCIe transfer, the controller
will lock up.
So we perform a PQI reset in the driver's shutdown callback function to
eliminate the possibility of a controller/host PCIe transfer being
active when the kernel clears BME immediately after calling the driver's
shutdown callback.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make pass-thru requests bi-directional
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- distinguish between shutdown and non-shutdown.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The smartpqi firmware will bypass the cache for any request larger than
1MB, so we should cap the request size to avoid any performance
degradation in kernels later than v4.3
This degradation is caused from d2be537c3b,
which changed max_sectors_kb to 1280k, but the hardware is able to
work fine with it, so the true fix should be from smartpqi driver.
Signed-off-by: Yadan Fan <ydfan@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
