* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (23 commits)
firewire: ohci: extend initialization log message
firewire: ohci: fix IR/IT context mask mixup
firewire: ohci: add module parameter to activate quirk fixes
firewire: ohci: use an ID table for quirks detection
firewire: ohci: reorder struct fw_ohci for better cache efficiency
firewire: ohci: remove unused dualbuffer IR code
firewire: core: combine a bit of repeated code
firewire: core: change type of a data buffer
firewire: cdev: increment ABI version number
firewire: cdev: add more flexible cycle timer ioctl
firewire: core: rename an internal function
firewire: core: fix an information leak
firewire: core: increase stack size of config ROM reader
firewire: core: don't fail device creation in case of too large config ROM blocks
firewire: core: fix "giving up on config rom" with Panasonic AG-DV2500
firewire: remove incomplete Bus_Time CSR support
firewire: get_cycle_timer optimization and cleanup
firewire: ohci: enable cycle timer fix on ALi and NEC controllers
firewire: ohci: work around cycle timer bugs on VIA controllers
firewire: make PCI device id constant
...
Before each FCP transdaction, the entire 512 bytes of the FCP frame were
cleared, then values filled in.
Clear only the bytes between filled-in bytes and end of the
- request frame, or
- response frame if data from a larger response will be needed, or
- whole frame if data from a variable length response will be taken.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FCP transactions as well as CMP transactions were serialized with
mutex_lock_interruptible. It is extremely unlikly though that a signal
will arrive while a concurrent process holds the mutex. And even if one
does, the duration of a transaction is reasonably short (1.2 seconds if
all retries time out, usually much shorter).
Hence simplify the code to plain mutex_lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a portability fix and reduces stack usage.
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firedtv (payload of write requests in avc_write and
of lock requests in cmp_lock) to slab-allocated memory.
We use the 512 bytes sized FCP frame buffer in struct firedtv for this
purpose. Previously it held only incoming FCP responses, now it holds
pending FCP requests and is then overwriten by an FCP response from the
tuner subunit. Ditto for CMP lock requests and responses. Accesses to
the payload buffer are serialized by fdtv->avc_mutex.
As a welcome side effect, stack usage of the AV/C transaction functions
is reduced by 512 bytes.
Alas, avc_register_remote_control() is a special case: It previously
did not wait for a response. To fit better in with the other FCP
transactions, let it wait for an interim response.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is ever going to be a FireDTV or FloppyDTV firmware which does
not provide a minimal ASCII textual descriptor for Model_Id --- or if
the descriptor is provided indirectly in a descriptor directory ---
the ieee1394 variant of the device probe of firedtv would dereference a
NULL pointer. The firewire variant of firedtv's device probe is not
affected.
The fix makes sure that such an unexpected firmware is safely recognized
by fdtv_alloc as an unknown firmware.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core (sysfs attributes), the firedtv driver, and possible future
drivers all read strings from some configuration ROM directory. Factor
out the generic code from show_text_leaf() into a new helper function,
modified slightly to handle arbitrary buffer sizes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Control of more than one AV/C device at once --- e.g. camcorders, tape
decks, audio devices, TV tuners --- failed or worked only unreliably,
depending on driver implementation. This affected kernelspace and
userspace drivers alike and was caused by firewire-core's inability to
accept multiple registrations of FCP listeners.
The fix allows multiple address handlers to be registered for the FCP
command and response registers. When a request for these registers is
received, all handlers are invoked, and the Firewire response is
generated by the core and not by any handler.
The cdev API does not change, i.e., userspace is still expected to send
a response for FCP requests; this response is silently ignored.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changelog, rebased, whitespace)
All read transactions initiated by firedtv are only quadlet-sized, hence
the backend->read call can be simplified a little.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Packet DMA buffers are queued either initially all at once (then, a
queueing failure will cause firedtv to release the DMA context as a
whole) or subsequently one by one as they recycled after use (then a
failure is extremely unlikely). Therefore we can be a little less
cautious when counting at which packet buffer to set the interrupt flag.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache only addresses of whole pages, not of each buffer chunk. Besides,
page addresses can be obtained by page_address() instead of kmap() since
they were allocated in lowmem.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add #include <dvb_demux.h> for dvb_dmx_swfilter_packets(). This was
already indirectly included via firedtv.h, but don't rely on it.
The 4 bytes which were referred to as FIREWIRE_HEADER_SIZE are actually
the source packet header from IEC 61883-4 (MPEG2-TS data transmission
over 1394), not e.g. the IEEE 1394 isochronous packet header. So choose
a more precise name.
Also, express the payload size as a preprocessor constant too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
Canceling of the remote control workqueue job is factored into
firedtv-rc.c. Plus trivial whitespace change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since 2.6.32(-rc1), DVB core checks the return value of
dvb_frontend_ops.set_frontend. Now it becomes apparent that firedtv
always returned a bogus value from its set_frontend method.
CC: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This solves a problem in firedtv that has become major for Swedish DVB-T
users the last month or so. It will most likely solve issues seen by
other users as well.
If the length of an AVC message is greater than 127, the length field
should be encoded in LV mode instead of V mode. V mode can only be used
if the length is 127 or less. This patch ensures that the CA_PMT
message is always encoded in LV mode so PMT message of greater lengths
can be supported.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
applications tend to check the signal strength very often. This patch
enables users to select which AVC messages to log using a bitmask. In
addition, it also enables the possibility to debug application PMTs sent
to the driver. This will be usable since the CA support is still poorly
tested for lots of CAMs and CA systems.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AVC protocol uses the same command for tuning and PID filtering and
since dvb-core uses a software zigzagging to do automatic retuning this
could cause all PID filters to be cleared. PID filter information is
now included in all DSD commands to the card.
Background:
There is a problem in the firedtv driver that causes recordings to stop
if the SW zigzag algorithm in dvb-core kicks in with a retune after the
application has set up the PID filters. Since tuning and setting PID
filters uses the same AVC command (DSD) and only the replace subfunction
is supported by the card, it is not possible to do a retune without
setting the PID filters. This means that the PID filtering has to be
sent in each tune.
This problem applies to C and T cards since S and S2 cards tune using a
vendor specific command. The patch corrects the problem by sending the
PID list in each tune. I have tested it on my T card with a good
result.
How to trigger problem: Zap to a channel and output AV to a file, e.g.
"tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull
the antenna cable from the card. The lock on the channel will disappear
and the TS file will stop increasing in size. Wait a couple of seconds.
Replug the cable again. You will get a lock on the channel again, but
the TS file will never increase in size agains sinze no PIDS are
filtered.
Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna
was plugged out and back in with DVB-T. Does not fix this with DVB-C,
but also doesn't regress on DVB-C.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 34aecd2851 was made obsolete
and invalid by commit 40cf65d149.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Beat Michel Liechti <bml303@gmail.com>
Tuning was broken on FireDTV S2 (and presumably FloppyDTV S2) because a
wrong opcode was sent. The box only gave "not implemented" responses.
Changing the opcode to _TUNE_QPSK2 fixes this for good.
Cc: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Eliminate
drivers/media/dvb/firewire/firedtv-avc.c: In function 'debug_fcp':
drivers/media/dvb/firewire/firedtv-avc.c:156: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
I found that the function fdtv_frontend_init in the file firedtv-fe.c was
missing a case for FIREDTV_DVB_S2 which resulted in "frequency limits
undefined" errors in syslog.
Signed-off-by: Beat Michel Liechti <bml303@gmail.com>
Change by Stefan R: combine it with case case FIREDTV_DVB_S as
originally suggested by Beat Michel. This enables FE_CAN_FEC_AUTO also
for FireDTV-S2 devices which is possible as long as only DVB-S channels
are used. FE_CAN_FEC_AUTO would be wrong for DVB-S2 channels, but those
cannot be used yet since the driver is not yet converted to S2API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Combination of the following changes:
Mon, 23 Feb 2009 14:21:10 +0100 (CET)
firedtv: reinstate debug logging option
Henrik Kurelid tells me that FCP debug logging (which I removed during
cleanups) is still useful when working on driver issues together with
end users. So bring it back in an updated form with only 60% of the
original code footprint.
Logging can be enabled with
# echo -1 > /sys/module/firedtv/parameters/debug
1 instead of -1 enables only FCP header logging,
2 instead of -1 enables only hexdumps of the entire FCP frames.
0 switches logging off again.
Fri, 20 Feb 2009 20:54:27 +0100 (CET)
firedtv: build fix for INPUT=m and DVB_FIREDTV=y
Thu, 19 Feb 2009 20:40:39 +0100
firedtv: use msecs_to_jiffies
Pointed out by Mauro Carvalho Chehab.
Sun Feb 15 20:50:46 CET 2009
firedtv: some more housekeeping
Fix an old checkpatch warning and a new compiler warning.
Sun Feb 15 15:33:17 CET 2009
firedtv: rename a file once more
At the moment, about a third of avc.c is specific to FireDTVs rather
than generic AV/C code. Rename it to firedtv-avc.c.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: more compact channels backing store
Replace struct firedtv_channel { bool active; int pid; } channel[16];
by unsigned long channel_active; u16 channel_pid[16];.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: some simplifications
c->active was unnecessarily cleared twice.
Also, by marking the channel inactive before the for loop,
the loop becomes identical with fdtv_channel_collect().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: remove a bogus loop
This loop is unnecessary because
- only active channel[].pid's will be sent to the device,
- when a channel is activated, its pid is set to dvbdmxfeed->pid.
Perhaps the original code was there because it was initially not fully
covered by the fdtv->demux_mutex.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix mutex protection
fdtv_start_feed() accessed the channel list unsafely.
Fully serialize it with itself and fdtv_stop_feed().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix missing braces
Original code was:
...
case DMX_TS_PES_OTHER:
//Dirty fix to keep firesat->channel pid-list up to date
for(k=0;k<16;k++){
if(firesat->channel[k].active == 0)
firesat->channel[k].pid =
dvbdmxfeed->pid;
break;
}
channel = firesat_channel_allocate(firesat);
break;
default:
...
Looks bogus in several respects. For now let's just add braces to the if
because that seems to be what the author meant.
Sun Feb 15 15:33:17 CET 2009
firedtv: allow build without input subsystem
!CONFIG_INPUT is very unlikely on systems on which firedtv is of
interest. But we can easily support it.
Sun Feb 15 15:33:17 CET 2009
firedtv: replace EXTRA_CFLAGS by ccflags
The former are deprecated.
The latter can depend on Kconfig variables.
Sun Feb 15 15:33:17 CET 2009
firedtv: concentrate ieee1394 dependencies
Move the entire interface with drivers/ieee1394 to firedtv-1394.c.
Move 1394-independent module initialization code to firedtv-dvb.c.
This prepares interfacing with drivers/firewire.
Sun Feb 15 15:33:17 CET 2009
firedtv: amend Kconfig menu prompt
Sun Feb 15 15:33:17 CET 2009
firedtv: remove kernel version compatibility macro
Sun Feb 15 15:33:17 CET 2009
firedtv: combine header files
avc.h and firedtv-*.h are small and currently not shared with other
drivers, hence concatenate them all into firedtv.h.
Sun Feb 15 15:33:17 CET 2009
firedtv: misc style touch-ups
Standardize on lower-case hexadecimal constants. Adjust whitespace.
Omit unnecessary pointer type casts and an unnecessary list head
initialization. Use dev_printk.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc, ci: remove unused constants
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from read descriptor response operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from DSD command operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: header file cleanup
Remove unused constants and declarations.
Move privately used constants into .c files.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from FCP frame types
Don't use bitfields in struct types of on-the-wire data.
Also move many privately used constants from avc.h to avc.c
and remove some unused constants.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: fix offset in avc_tuner_get_ts
The parentheses were wrong. It didn't matter though because this code
only writes a 0 into an area which is already initialized to 0.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: reduce stack usage, remove two typedefs
It is safe to share a memory buffer for command frame and response frame
because the response data come in after the command frame was last used.
Even less stack would be required if only the actual required frame size
instead of the entire FCP register size was allocated.
Also, rename the defined types AVCCmdFrm and AVCRspFrm to
struct avc_command_frame and struct avc_response_frame.
TODO: Remove the bitfields in these types.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: cmp: move code to avc
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: move code to firedtv-1394
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: remove unnecessary struct type definitions
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: style changes and fixlets
Add cleanup after failure in setup_iso_channel.
Replace printk() by dv_err().
Decrease indentation level in rawiso_activity_cb().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Combination of the following changes:
Sat, 17 Jan 2009 14:47:34 +0100
firedtv: rename variables and functions from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Renamed struct firedtv *firedtv to struct firedtv *fdtv and
firedtv_foo_bar() to fdtv_foo_bar() for brevity.
Sat, 17 Jan 2009 13:07:44 +0100
firedtv: rename files from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Name the directory "firewire" instead of "firedtv".
Standardize on "-" instead of "_" in file names, because that's what
drivers/firewire/ and drivers/media/dvb/dvb-usb/ use too.
Build fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
