After detecting failure due to module initialization error, get out.
Don't report jammed hardware. Problem due to a missing break statement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver also contains a piece of configuration data that produces a
one line description of the specific hardware being driver
(e.g. "Hauppauge 24xxx", "OnAir", etc). This change generates an
informational message to the kernel log reporting the hardware type
being driven. This is a very useful thing to know when diagnosing
problems.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It used to be that the only real detectable reason for the driver to
fail during initialization would be that if the hardware is simply
jammed. However with the advent of the sub-device mechanism in V4L it
is possible now to detect if a sub-device module fails to load
successfully. The pvrusb2 driver does in fact react to this by also
(correctly) failing, however the original diagnostic message "hardware
is jammed" was still being reported. This misleads the user because
in fact it might not actually be a hardware failure. This change adds
logic to tell the difference and then report a more appropriate
message to the kernel log.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Encoder failures are mostly recoverable by the driver. While
it would sure be nice not to have the failure happen in the first
place, this has been going on for years and I doubt that a real
solution will ever present itself. I think that part's firmware is
just slightly flakey and we have to deal with it. The driver does
deal with it just fine, but the warning message going into the kernel
log is probably a little more alarming than it should be. So try to
soften up the warning somewhat.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Associate V4L device node in sysfs with the underlying USB
device. This opens the door to device information tracking in udev
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
consolidate common code used to determine if calibration on startup is needed
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_attach, and the cal module option isn't disabled, then we
should run the initialization and calibration procedures during the
tda18271_attach function call, regardless of how many instances of the
driver have been attached. If the device is already calibrated, the
driver will detect that and will only calibrate again if necessary.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_set_config, and the cal module option isn't disabled,
then we should run the initialization and calibration procedures
during the tda18271_set_config function call.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the set_config method to allow drivers to configure the
tda18271 driver options after attach.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is already an option for sending 16 byte chunks rather that writing
39 bytes all at once during the tuner's initialization. Some i2c buses
can't send 16 bytes at once, so create an option for sending 8 byte chunks.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Terry Wu for finding the GPIOs required for svideo / composite input
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
on the slave tuner, only. The master tuner must always leave
slave tuner output / loop thru enabled.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add flip/mirror support for OV2640
- fix for backlight value range
- fix for red-blue inversion hue mode with V4L1 applications
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original implementation of pac_find_sof() does not always find
the Start Of Frame (SOF) marker. Replace it with a state machine
based design.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.
Thanks to Michael Krufky for pointing out this issue.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for saturation/hue controls, prompted by errors showing up in
the mythbackend log.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: Don't resubmit error status URB's when suspending
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gscpa core was not resubmitting URB's when the URB status was an error,
this means we will loose URB's (potentially all stopping the stream) in
case of sporadic USB issues. I've seen this with an Aiptek stv0680 based
PenCam connected through an USB 2.0 hub.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a new subdriver to gspca supporting cams with the stv0680
bridge (replacing the old in kernel v4l1 driver).
Many thanks to Hans Verkuil for providing me with one of the 2 cams used in
testing this new sub driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca w9968cf: slight tweak to vstart and hstart to get rid of black borders
in 640x480 mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca w9968cf: Add support for JPEG compression, this enables much higher
framerates at 320x240 / 352x288 and also allows for 640x480 mode for
cams which can do this. The w9968cf uses planar JPEG, which libv4l until
now did not support, so this requires atleast version 0.6.3 of libv4l.
And something important I forgot to mention in my earlier w9968cf commits:
Many thanks to Hans Verkuil for giving me a w9968cf based cam, which has
allowed me to develop the gspca w9968cf support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca-w9968cf: Don't add an extra packet to the buffer after the EOF,
this makes the frame data size bigger then it should be which makes
gstreamer discard it.
This patch also fixes an unrelated compiler warning.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache sensor regs to avoid unnecessary slow i2c reads / writes, this speeds
up sd_start a bit with most bridges and a lot (from 5 seconds down to 0.3
seconds) with W996xCF cams, as this avoids very slow bit bang IO over
USB i2c reads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to gspca for the Winbond W9967CF and W9968CF
camera's. This is mostly a port of the existing v4l1 driver to gspca
(making it v4l2). But this also features fixes to the bitbanging i2c code
(send a nack not an ack after reading the last byte of a transfer), which
gets rid of the weird errors which were being seen there, and of
the smbus_refresh() hack to get around these errors.
Also the vstart settings have been tweaked to work with different
frequency filter settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the I2C device provides an interrupt it is registered and the
standard
is updated via interrupts rather than polling.
Since I2C communication is needed, the interrupt handler fires off a
work which will check the new standard, and store it in the internal
structure.
To handle mutual exclusion a mutex is introduced.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch defines the probe and remove function as __devinit and __devexit.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for settings the input standard of the ADV7180.
When the input standard is set there is no use to ask the
chip for standard, therefore it is cached in the driver.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to the ADV7180 driver to check the input
status.
Since the status is held in the same register as the input standard
a small restructuring of the code is done to reuse the code for
reading the register
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds the device IDs and driver linking to allow the Asus Europa DVB-T
card to operate with these drivers.
The device has a SAA7134 chipset with a TD1316 Hybrid Tuner.
All inputs work on the card including switching between DVB-T and
Analogue TV, there is also no IR with this card.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Danny Wood <danwood76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The definition of tvaudio_tuner_ops initializes the s_tuner field twice.
It appears that the second case should initialize the g_tuner field.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the image size (bytesperline*height) is not multiple
of PAGE_SIZE, v4l2 rounded the required buffer size to
be multiple of PAGE_SIZE. This prevented user space
to store images directly into userptr buffers which were
not multiple of PAGE_SIZE. This constraint is removed.
The start address is still assumed to be required
page-aligned, ie., when v4l2 allocates mmap buffers,
the offset between different buffers is page-aligned.
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVBS2API introduced two new ioctls that allows changing/getting details about newer
video standards like DVB-S2 and ISDB-T. There are lots of thing to do in this chapter,
but, for now, just add a session there, in order to allow make to not complain about
undefined symbol.
With this patch, all ioctls at the frontend.h API were somehow documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to add the documentation for FE_[GET|SET]_PROPERTY that
is not specific to isdb-t. Instead of doing it at frontend.xml,
it is better to have a separate session for it. Also, isdbt.xml assumes
that those ioctls were already introduced, and documents several exisiting
properties. So, better to just rename it and add the documentation for it,
together with each existing property there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this ioctl should not be used, and is a good canditate for
Documentation/feature-removal-schedule.txt, while it is on kernel,
it needs to be documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
