Function i5k_channel_pci_id looks like it can fail, while a better
code design would make it more obvious that it can't. We can even get
rid of the function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Replace unnecessary if with else statement.
This fixes the following (false) compile warning reported with some combinations
of C compiler version and configuration.
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here
drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here
drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in
this function
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
rs_resp is dynamically allocated in aem_read_sensor(), so it should be freed
before exiting in every case. This collects the kfree and the return at
the end of the function.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # 2.6.27+
pmbus_clear_faults() attempts to clear faults on non-existing real pages.
As a result, the command error bit in the status register is set, and faults
are not really cleared.
All byte writes to non-zero pages are requests to clear the status register
on that page. Since non-zero pages are virtual and do not exist on the chip,
there is nothing to do, and such requests have to be ignored. This fixes
above problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual pages and to be able to handle more chips, it is necessary to
virtualise pmbus_write_byte().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
Several vendors implement a second configuration register, which we
check during device detection. Refactor the code to avoid duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With a device ID register value of 0, the SA56004 detection is rather
weak. Check several other register too to confirm the detection, as we
do for other supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The optional extended local temperature register can never have
address 0, as this address is already used by another register. Thus
we can get rid of flag LM90_HAVE_LOCAL_EXT and simply rely on
reg_local_ext being non-zero to determine if a given chip has this
extension or not. This makes the code more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
LM95231 is fully compatible to LM95241; only necessary change is to add
chip detection.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX1668 and compatibles have several external temperature sensors, but only a
single FAULT status bit. If a fault occurs, the temperature reported on the
affected sensors is 127 degrees C. Use this knowledge to report fault on
external sensors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: David George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm78) Become the maintainer
hwmon: (lm78) Make ISA interface depend on CONFIG_ISA
hwmon: (lm78) Avoid forward declarations
hwmon: (sht15) Correct a comment mistake
hwmon: (max1111) Avoid extra memory allocations
hwmon: (it87) Add chassis intrusion detection support
hwmon: (via-cputemp) Add VID reporting support
hwmon-vid: Add support for VIA family 6 model D CPU
hwmon: New driver sch5636
hwmon: (sch5627) Factor out some code shared with sch5636 driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Declare myself the maintainer of the lm78 driver. I still have a
running system with one of these chips.
Also count myself as a co-author of the driver. With 34 commits over
6 years, it seems fair.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We should only include support for the ISA interface of the LM78/LM79
if CONFIG_ISA is set. Not only this makes the driver somewhat smaller
on most architectures, but this also avoids poking at random I/O
ports on these architectures.
This is very similiar to what was done for the w83781d driver in
October 2008.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dean Nelson <dnelson@redhat.com>
Move code around to avoid several forward declarations. Also group
ISA-related functions together, to make future changes easier.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dean Nelson <dnelson@redhat.com>
sht15_store_heater() is called on _write_ access to heater_enable.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We can allocate the tx and rx buffers as part of our data structure.
Doing so is faster and spares memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Stanislav Brabec <utx@penguin.cz>
At least VIA family 6 model D CPU report the VID settings in a MSR,
so expose the value to user-space. Not sure about model A.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
The VIA family 6 model D CPU (C7-D, Eden 90 nm) can use two different
VID tables, we have to check the value of a MSR to decide which one to
use.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.
Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds a new sch56xx-common.ko which contains code which will also
be used in the new sch5636 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
spi_sync call uses its spi_message parameter to keep completion information,
using a drvdata structure is not thread-safe. Use a mutex to prevent
multiple access to shared driver data.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Cyril Hrubis <metan@ucw.cz>
Tested-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
A copy-and-paste error caused it87_attributes_vid to be referenced
where it87_attributes_label should be. Thankfully the group is only
used for attribute removal, not attribute creation, so the effects of
this bug are limited, but let's fix it still.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The object returned by atk_gitm is dynamically allocated and must be
freed.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.
Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.
Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle errors on 8-bit register reads and writes too. Also use likely
and unlikely to make the functions faster on success.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Additional temperature attribute support is easy to detect, so do it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39
Some PMBus devices return no error when reading fan speed registers, but don't
really support fans. Strengthen fan detection by also checking if fan
configuration registers exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39
Probe function did not free allocated memory if it failed. Fix it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus devices do not support the PMBus revision register, so don't check
if it exists.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39
Call sysfs_attr_init() from atk_init_attribute() to handle sysfs attribute
initialization in a single function.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
pdev_entry.cpu and pdev_entry.cpu_core_id aren't used anywhere in the
driver code so we can drop these struct members.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Further relax temperature range checks after reading the IA32_TEMPERATURE_TARGET
register. If the register returns a value other than 0 in bits 16..32, assume
that the returned value is correct.
This change applies to both packet and core temperature limits.
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Commit a321cedb12 excludes CPU models 0xe, 0xf,
0x16, and 0x1a from TjMax temperature adjustment, even though several of those
CPUs are known to have TiMax other than 100 degrees C, and even though the code
in adjust_tjmax() explicitly handles those CPUs and points to a Web document
listing several of the affected CPU IDs.
Reinstate original TjMax adjustment if TjMax can not be determined using the
IA32_TEMPERATURE_TARGET register.
https://bugzilla.kernel.org/show_bug.cgi?id=32582
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@kernel.org> # .35.x .36.x .37.x .38.x .39.x
The current temperature range check of MSR_IA32_TEMPERATURE_TARGET
seems too strict to me, some TjMax values documented in
Documentation/hwmon/coretemp wouldn't pass. Relax the check so that
all the documented values pass.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The temp_fault sysfs attribute is wrong, it should be temp2_fault instead.
Reported-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
chk_ucode_version() is only called from coretemp_probe() which is
__devinit, so it can be marked __devinit too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Update comments describing the handling of HT CPUs based on review feedback.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The abituguru drivers are only built on X86, where DMI support is now
enabled by default. So let these drivers depend on DMI, for the
following gains:
* Robustness and safety. Detection of these devices is weak and uses
non-standard methods, it should really be limited to Abit boards
unless the user explicitly asks otherwise.
* Code simplicity. The code is easier to read without ifdefs.
* Better build testing coverage. Now there's only one way to build the
drivers, so no risk of build failure on exotic systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Serialize access to the hardware by using "request_muxed_region" macro
defined by Alan Cox. Call to this macro will hold off the requestor if
the resource is currently busy. "superio_enter" will return an error
if call to "request_muxed_region" fails. Rest of the code change is to
ripple an error return from superio_enter to the top level.
Signed-off-by: Nat Gurumoorthy <natg@google.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sch5627 needs to be explicitly told to start an adc conversion
for Vbat, once in a while. Without this Vbat may read 0, and will never
get updated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch generalizes sch5627_read_virtual_reg so that it can
be used to write virtual regs too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sigend-off-by: Jean Delvare <khali@linux-fr.org>
The MAX6650 has only one fan input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6650 device detection is unreliable, we got reports of false
positives. We now have many ways to let users instantiate the devices
explicitly, so unreliable detection should be dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
As discussed earlier, the ACPI power meter driver would better live
in drivers/hwmon, as its only purpose is to create hwmon-style
interfaces for ACPI 4.0 power meter devices. Users are more likely to
look for it there, and less likely to accidentally hide it by
unselecting its dependencies.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Len Brown <lenb@kernel.org>
The config SENSORS_ASC7621 entry is inside an if HWMON / endif block,
so it already depends on HWMON.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
While the JC42-compatible chips are temperature sensors, I2C_CLASS_SPD
makes more sense because these chips always live on memory modules.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
This CPU family provides NB register values to gather following
TDP information
* ProcessorPwrWatts: Specifies in Watts the maximum amount of power
the processor can support.
* CurrPwrWatts: Specifies in Watts the current amount of power being
consumed by the processor.
This driver provides
* power1_crit (ProcessorPwrWatts)
* power1_input (CurrPwrWatts)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMDs upcoming CPUs use the same mechanism for the internal
temperature reporting as the Fam10h CPUs, so we just needed to add
the appropriate PCI-ID to the list.
This allows to use the k10temp driver on those CPUs.
While at it change the Kconfig entry to be more generic.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use helper functions to set and get driver data. This is more elegant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The coretemp driver provides a single set of device attributes for each
physical core of a HT CPU to avoid duplicate sensors. This
functionality was introduced with commit d883b9f097 ("hwmon:
(coretemp) Skip duplicate CPU entries").
Commit e40cc4bdfd ("x86/hwmon: register alternate sibling upon CPU
removal") extends this functionality to register the HT sibling of a CPU
which is taken offline, to ensure that sensor attributes are provided if
at least one HT sibling of a core is online.
Add comments into the code describing the functionality in some more
detail.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpu_sibling_mask() is not defined unless CONFIG_SMP is defined, so it
must not be used directly in the code without ifdef protection.
To solve the problem and avoid ifdefs in the code, define
for_each_sibling() and use it instead.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the merge of pkgtemp functionality into the coretemp driver,
the pkgtemp driver is no longer necessary. Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch merges the pkgtemp with coretemp driver.
The sysfs interfaces for all cores in the same pkg
are shown under one directory, in hwmon. It also
supports CONFIG_HOTPLUG_CPU. So, the sysfs interfaces
are created when each core comes online and are
removed when it goes offline.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
[guenter.roeck@ericsson.com: Fixed section reference errors]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Analog Devices ADM1275 Hot-Swap Controller and Digital Power
Monitor
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Hardware monitoring support for TI UCD90120, UCD90124, UCD9090, and UCD90910
Sequencer and System Health Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for TI UCD9220, UCD9222, UCD9224,
UCD9240, UCD9244, UCD9246, and UCD9248 Digital PWM System Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Fan control implementation tends to be device specific, so start using
the device specific function call to read fan configuration registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Some devices use non-standard registers to access various functionality.
This does not only affect status registers, but other registers as well.
Rename local get_status function to get_byte_data to reflect this requirement.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This commit replaces hard-coded sensor and limit register detection code
with table based sensor detection. This change eliminates code block repetition
and reduces code size.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The sht15 sensor allows validating exchanges to and from the device
using a crc8 function. An utility function to reverse a byte has also
been added.
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add support for:
- Heater.
- End of battery notice.
- Ability not to reload from OTP.
- Low resolution (12bit temp, 8bit humidity).
* Add an utility function to read individual bytes from the device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Move the creation of sysfs attributes after the end of the
initialization, and remove them in the error path.
* Release regulator in the error path.
* Add a soft reset command (need to wait 11ms before next command).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add a documentation file for the device.
* Respect a bit more the kernel-doc syntax.
* Rename some variables for clarity.
* Use bool type for flags.
* Use an enum for states (actions being done).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor with
Overtemperature Alarm from Maxim.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The driver did not return an error if the call to hwmon_device_register failed.
Fix by returning the error reported from hwmon_device_register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We must remove all files we created, even in error cases.
Fixes second part of kernel bug #34072:
https://bugzilla.kernel.org/show_bug.cgi?id=34072
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
struct pmbus_data included an unused variable named status_bits.
Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Commit 8677011 added auto-update to temperature limit registers.
Unfortunately, the update flag is also used to determine if an attribute
is writable, which results in read-only temperature limit registers.
To fix the problem, pass 'readonly' as separate flag to the function used
to add sensor attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Use tables to list the count of fan and temperature inputs for all
supported chips, almost similar to (but more simple than) what is
already done for voltage inputs. This avoids repeating the same tests
in different functions, and will make it easier to add support for
chips with a different count of fan or temperature inputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using C99-style array initialization will ensure definitions won't
drift if the chips enum gets new values added.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
mfd_get_cell returns a const, so change the jz4740 clients to store
a const mfd cell. This silences type mismatch warnings.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver exposes the sysfs nodes of the TWL4030 MADC module.
All the voltage channel values are expressed in terms of mV. Channel 13
and channel 14 are reserved. There are channels which represent
temperature and current the output is represented by celcius
and mA respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC SCH5627 Super I/O chips include complete hardware monitoring
capabilities. They can monitor up to 5 voltages, 4 fans and 8
temperatures.
The hardware monitoring part of the SMSC SCH5627 is accessed by talking
through an embedded microcontroller. An application note describing the
protocol for communicating with the microcontroller is available upon
request. Please mail me if you want a copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make the LM75/LM75A device detection faster:
* Don't read the current temperature value when we don't use it.
* Check for unused bits in the configuration register as soon as we
have read its value.
* Don't use word reads, not all devices support this, and some which
don't misbehave when you try.
* Check for cycling register values every 40 register addresses
instead of every 8, it's 5 times faster and just as efficient.
Some of these improvements come straight from the user-space
sensors-detect script, so both detection routines are in line now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for detection of the National Semiconductor LM75A using the ID
register value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The lis3lv02d drivers aren't hardware monitoring drivers, so the don't
belong to drivers/hwmon. Move them to drivers/misc, short of a better
home.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
The hp_accel driver isn't a hardware monitoring driver, so it doesn't
belong to drivers/hwmon. Move it to drivers/platform/x86, assuming HP
doesn't ship non-x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
The dependencies between the various lis3lv02d drivers make it
impossible to split them to different directories, while we really
want to do this. Move handling of dependencies from Makefile to
Kconfig, to make the move possible at all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
An integer overflow occurs in the calculation of RHlinear when the
relative humidity is greater than around 30%. The consequence is a subtle
(but noticeable) error in the resulting humidity measurement.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Jonathan Cameron <jic23@cam.ac.uk>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
hwmon: (lineage-pem): Fix in1 voltage alarm sysfs attributes
hwmon/f71882fg: Add support for f71808e
hwmon/f71882fg: Add support for f71869f and f71869e
hwmon/f71882fg: Add support for f71889ed
hwmon/f71882fg: Break out test for auto pwm's controlled by digital readings
hwmon/f71882fg: Separate temp beep sysfs attr from the other temp sysfs attr
hwmon/f71882fg: Remove bogus temp2_type for certain models
hwmon/f71882fg: Make number of temps configurable
hwmon/f71882fg: Make creation of in sysfs attributes more generic
hwmon/f71882fg: Only allow negative auto point temps if fan_neg_temp is enabled
hwmon/f71882fg: Fix temp1 sensor type reporting
hwmon: (w83627ehf) Display correct temperature sensor labels for systems with NCT6775F
hwmon: (w83627ehf) Add fan debounce support for NCT6775F and NCT6776F
hwmon: (w83627ehf) Update Kconfig for W83677HG-B, NCT6775F and NCT6776F
hwmon: (w83627ehf) Store rpm instead of raw fan speed data
hwmon: (w83627ehf) Use 16 bit fan count registers if supported
hwmon: (w83627ehf) Add support for Nuvoton NCT6775F and NCT6776F
hwmon: (w83627ehf) Permit enabling SmartFan IV mode if configured at startup
hwmon: (w83627ehf) Convert register arrays to 16 bit, and convert access to pointers
hwmon: (w83627ehf) Remove references to datasheets which no longer exist
...
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The alarm bit assumed to be a low voltage alarm bit is not set for low voltage
alarms, and the alarm bit assumed to be a high voltage alarm turns out to be a
general alarm bit which is set for both low and high voltage alarms.
Remove the in1_min_alarm sysfs attribute and rename in1_max_alarm to in1_alarm
to reflect the situation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Jonathan Michalon <johndescs@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Note that these 2 are register compatible and report the same superio id,
but they are 2 distinct chips / models!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Faber <thfabba@gmx.de>
Tested-by: Alexey Sychev <owl@umail.ru>
Tested-by: Dieter Bloms <dieter@bloms.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Note that this patch also makes 2 changes to the code paths for the f71889fg
to keep the code unified between the 2 (for simplicities sake). Both of these
are harmless for then f71889fg:
1) The first change is to always set the FAN_PROG_SEL bit to 0. This influences
accesses to some banked fan / pwm registers. On the f71889fg no registers
which we use are banked. On the f71889ed however some more fan registers
have been banked including one which we use, by making the FAN_PROG_SEL bit
0, address 0x96 will point to the right register.
2) The second change is to see a FANx_TEMP_SEL value of 0 as pointing to
a PECI / AMDSI value, and thus disable our pwm related sysfs attr.
This is correct for the f71889ed and on the f71889fg 0 is a reserved
value, so we should never see it and if we do, disabling the pwm related
sysfs attr is a sane thing to do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Greve <tg42@gmx.net>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Putting this check in its own switch case rather then in the switch case
for adding pwm auto point sysfs attr is cleaner. This is a preparation patch
for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Remove the temp2_type sysfs files for f8000 / f71858fg models,
this got in accidentally and is wrong as these models don't have a
Temperature Sensor Type Register at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the temp sysattr array for the standard models a 2d array, which allows
to use it for models with less temperatures too. This is a preparation
patch for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for adding support for more different models,
some of which have a sparse list of used voltage pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code for determining a sensort type for temp1 was based on me misreading
the datasheet, the tested registers do not determine what kind of sensor
is actually reported as temp1. Instead the enable / disable certain additional
digital sensor readouts throug PECI / AMDSI, etc. Independent of these settings
temp1 is still reading an external BJT or thermistor as configured by the
Temperature Sensor Type Register (0x6b).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Systems with NCT6775F reported temperature sensor labels for systems with
NCT6776F. This patch fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
NCT6776F and NCT6775F support debouncing the fan RPM signal. This can
help improve the stability of th RPM signal for some fans (Arctic cooling
fans for example).
This patch adds a module parameter fan_debounce, which when set to 1 enables
debounce for all fans that the chip supports.
Signed-off-by: Ian Dobson <i.dobson@planet-ian.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since the fan speed value can be above 0xff, we can no longer use
that value to determine if the fan speed reading is valid. This
makes it difficult to manipulate the stored fan speed register value.
If we store rpm instead of the fan speed register value, we do not
need to correct it if the fan divisor value is changed, and the above
mentioned problem no longer exists.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Some of the chips supported by this driver have 13 bit or 16 bit fan count
registers. This patch improves support for those registers, specifically for
NCT6775F. With the changes in this patch, fan speed is reported correctly even
if the fan divider is set to a low value, which results in a fan speed reading
above 0xff.
With this patch, the width of fan count registers is no longer used to determine
if the chip has fan divider register(s) or not. A dedicated flag is used instead
to determine if this is the case.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch adds support for NCT6775F and NCT6776F to the w83627ehf driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Ian Dobson <i.dobson@planet-ian.com> (NCT6776F)
Tested-by: Zachary Marzec <zmarzec@gmail.com> (ASUS P8P67 PRO/NCT6776F)
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
If SmartFan IV mode was configured at startup, it should be possible
to re-enable it later on.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
For newer chips, several registers are banked and thus need to be 16 bit.
Also, register addresses change.
To prepare for those chips, convert affected register arrays to 16 bit,
and change access to those registers to array pointers in struct w83627ehf_data.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Assume that each register is banked, and set the bank for each access.
Cache the bank number so it only needs to be set if it changes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This cleanup fixes most of the checkpatch warnings and errors in the w83627ehf
driver. Remaining warnings and errors are left untouched on purpose to avoid
making the code less readable.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch unifies temperature register access, and replaces simple_strtoXXX
with strict_strtoXXX throughout the driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
LTC4151 is High Voltage I2C Current and Voltage Monitor from Linear
Technology.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
LINEAR16 data format is unsigned, not signed. Impact is that affected
attributes report negative values in the upper half of the supported
value range.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
PMBus only has one set of limit registers for up to three temperature sensors.
Thus, changing a limit for one of the temperature sensors affects limits for
other temperature sensors in the same page (and potentially multiple pages
depending on the chip implementation). To handle this situation, re-read all
temperature limit registers when updating sensor data. This way, all affected
temperature limits are updated whenever the limit for a single sensor is
changed.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Assumption so far was that PMBus devices would support TEMP2 and TEMP3 registers
only on page 0, and that only the TEMP1 register would be used/supported
on other pages.
Turns out that is not correct. UCD92xx devices support TEMP1 and TEMP2 on
page 0, and TEMP2 on other pages. So it is necessary to change the core code
such that it does not make a page based assumptions about temperature register
support.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
So far, it seemed like fans would either all be in page 0, or that
there would be one page per fan.
Turns out this was a wrong assumption. There is at least one PMBus
fan controller which supports three pages with four fans each.
Update code to handle this situation.
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
Some PMBus chips do not support the VOUT_MODE register. To make matters worse,
such chips may not return an error when reading the register either, but instead
return 0xff.
Check if the register exists using pmbus_check_byte_register() before reading
its value. In addition, validate the returned value and ignore it if it is 0xff
(which is invalid).
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
EMC6D103S is similar to EMC6D103, only it does not support registers 62[5:7],
6D[0:7], and 6E[0:7]. Register respective sysfs attributes and update affected
registers for all other chips only.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, the driver updates temp_auto_hyst and temp_auto_off if temp_auto_min changes.
This may cause problems if temp_auto_off was not configured before configuring
temp_auto_min, because one of the variables used (off_desired) is not initialized
in this case.
To simplify the code, and for consistency with other drivers, no longer update the delta
between "min" and "off" until the user sets the "off" value again.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADT7463 and ADT7468 optionally support VID5 instead of the standard +12V
measurement input. Use a boolean to identify the chip configuration instead of
hardcoding it several times.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the lis3lv02d SPI driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch initializes register CONFIG3 to a reasonable default PWM frequency
of 25kHz, to prevent audible sound in fan.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This avoids a possible race leading to trying to dereference NULL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
I2C address range included 0x2a, which the chips do not support.
Replace with 0x29 which is supported but was missing.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
LM64 has 16 degrees Celsius temperature offset on all
remote sensor registers.
This was not considered When LM64 support was added to lm63.c.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Turn down the no IRQ message - on some platforms that's a normal state of
affairs.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ASUS Sabertooth X58 has a bug in ACPI that prevents the reading of MCH
temperature when the "old" ATK0110 interface is used. Add a DMI entry
to override the detection heuristic and force the use of the "new"
interface on this board.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Joris Creyghton <jorisctn@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The switch to dynamically allocated sysfs attributes left the
internal lockdep members uninitialized, causing a formal bug.
This patch adds sysfs_attr_init() to the node creation function,
remedying the problem.
Reported-and-tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Minor cleanups. Mostly removing assignments in if statements to get
rid of checkpatch errors.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the 1.5V voltage monitoring input (in7) of the
SMSC SCH5127 chip.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
EMC1423 uses the similar register and adds a hardware shutdown pin to
protect exceed temperature. This function is set by resistor; it's not
necessary to do anything in the driver except add the emc1423 pid of 0x23.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
[Updated Kconfig/comments and minor further changes asked for by the hwmon
maintainers]
Signed-off-by: Alan Cox <alan@linux.intel.com>
[Fixed checkpatch warning]
Signed-of--by: Jean Delvare <khali@linux-fr.org>
This is the same case as fschmd, from which the code was copied as far
as I can see. So the same clean-up applies:
The WDIOC_GETSUPPORT ioctl only needs a mutex because it operates on a
static variable. There is no good reason to keep this variable static,
so let's just make it non-static and drop the now useless mutex
altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
As discussed one year ago, the WDIOC_GETSUPPORT ioctl only needs a
mutex because it operates on a static variable. There is no good
reason to keep this variable static, so let's just make it non-static
and drop the now useless mutex altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
[JD: Also convert debug messages]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code triggers a false warning with older versions of gcc:
w83795.c: In function 'w83795_update_device':
w83795.c:475: warning: 'lsb' may be used uninitialized in this function
I admit that the code is a little tricky, but I see no way to write it
differently without hurting performance. So let's just silent the
warning with a needless initialization.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Trivial patch updating my email contact details due to change of
employer, and because I no longer have access to the previously used
domain.
Unfortunately I also no longer have access to any ads7828 hardware, but
am happy to support/maintain the driver if others are able to test
changes.
Signed-off-by: Steve Hardy <shardy@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch fixes all checkpatch errors and most of the checkpatch warnings.
It also fixes the range check in applesmc_store_fan_speed().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
With the preceding patches, git blame assigns about half of
the file to the present author. Add a line to the copyright
to reflect this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the driver report a single line on success.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Given the dynamic node construction method, the setup of the
accelerometer, light sensor and keyboard backlight sysfs nodes
can be simplified. This patch does not contain any logic changes.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With the dynamic temperature group in place, the setup of fans
can be simplified. This patch sets up the fans dynamically, removing
a hundred lines of code.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With temperature keys being determined automatically, the dmi match
data is only used to assign features that can easily be detected from
the smc. This patch removes the dmi match data altogether, and reduces
the match table to the main machine models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent Macbooks have temperature registers of a new type.
This patch adds the logic to handle them.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The current driver creates temperature files based on a list
of temperature keys given per device. Apart from slow adaption
to new machine models, the number of sensors also depends on
the number of processors. This patch looks up the temperature
keys dynamically, thereby supporting all models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
One main problem with the current driver is the inability to quickly
search for supported keys, resulting in detailed feature maps per
machine model which are cumbersome to maintain.
This patch adds a register lookup table, which enables binary search
for supported keys. The lookup also reduces the io frequency, so the
original mutex is replaced by locks around the actual io.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
[guenter.roeck@ericsson.com: Added value range check to key_at_index_store()]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Cc: stable@kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch add support for the MacBookAir3,1 and MacBookAir3,2 to the
applesmc driver.
[rydberg@euromail.se: minor cleanup]
Cc: stable@kernel.org
Signed-off-by: Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The owner field was removed from struct attribute in
6fd69dc578, so don't assign it anymore.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This commit fixes the following compile warnings.
From v2.6.37-rc2/m68k/m68k-allmodconfig, v2.6.37-rc2/powerpc/powerpc-randconfig:
drivers/hwmon/lis3lv02d_i2c.c:222: warning: 'lis3_i2c_runtime_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:231: warning: 'lis3_i2c_runtime_resume' defined but not used
Seen if CONFIG_PM_RUNTIME is not set.
From v2.6.37-rc2/sh4/sh-allyesconfig:
drivers/hwmon/lis3lv02d_i2c.c:191: warning: 'lis3lv02d_i2c_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:201: warning: 'lis3lv02d_i2c_resume' defined but not used
Seen if CONFIG_PM is set but CONFIG_PM_SLEEP is not.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the following compile warning.
drivers/hwmon/i5k_amb.c:500: warning: 'i5k_amb_ids' defined but not used
The warning is seen if the driver is built into the kernel (not as module).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current implementation, the sysfs entries is not removed before return -ENODEV.
Creating the sysfs attribute should be the last thing done by the function,
after all the rest has been successful.
Otherwise there is a small window during which user-space can access the attribute
but the driver isn't ready to deal with the requests.
Fix it by moving sysfs_create_group to be the last thing done by the function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Return proper error if i2c_check_functionality reports
the adapter does not support the capability we need.
Also remove unneeded initialization for err variable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.
Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cascaded conditionals are inefficient. Reorder the fields so that
PWM register addresses can be computed more efficiently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is no point in reading registers during initialization if we
will refresh the values in the update function later. This is only
slowing down the driver loading with no benefit, stop doing it.
This change saves 480 ms on driver load on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All 3 temperature sensor type sysfs functions (show_temp_mode,
store_temp_mode and show_dts_mode) can be simplified. We don't
create these files when the correponding input isn't in temperature
monitoring mode, so there is no point in handling that case.
Likewise, we don't allow changing inputs from temperature to voltage,
so the code handling this case is dead and can be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor
type (fans need 4, other sensors need 6). Get rid of it to prevent
any confusion. Also get rid of the useless masking, the meaningful
bits are always the MSb so there's nothing to mask out after
shifting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shorten driver load time by avoiding duplicate register access during
initialization. This saves 112 ms on modprobe on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle beep_enable just like all other beep bits. It doesn't need
anything special, so let's avoid redundant code. This also saves a
duplicate register read at initialization time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The PWM duty cycle frequenty attributes are improperly named
(fanN_div instead of pwmN_div) and contain raw values instead of
actual frequencies. Rename them and fix their contents.
Also improve the logic when the user asks for a new frequency, to
always pick the closest supported frequency. The algorithm could
certainly be optimized, but the operation is infrequent enough that
I don't think it's worth the effort.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83795G can be configured to set the in0, in1 and/or in2 voltage
limits dynamically based on VID input pins. Switch the respective
sysfs attributes to read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Misplaced parentheses caused the wrong register value to be read,
resulting in random LSB for fan speed values and limits.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The data structure is zalloc'd, so no need to set individual fields
to 0 explicitly.
* Refactor the handling of pins that can be used for either
temperature or voltage monitoring.
* Misc other clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only create fan[1-8]_target files when the fan in question can be
controlled (PWM output is present.) Also name these files according
to the standard.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a dedicated 2D array for PWM attributes. This way, PWM attributes
are handled the same way as other attributes, this is more consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use 2D arrays for in, fan, temp and dts device attributes. Using
linear arrays is too risky as we have to skip some groups depending
on the device model and configuration. Adding or removing an
attribute would let the driver build silently but then it would crash
at runtime. With 2D arrays, the consistency checking happens at build
time, which is much safer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Functions w83795_create_files and w83795_remove_files iterate over
the same set of files, just calling a different function. Merge them
into a single function which takes the action as a parameter. This
saves code, and also ensure that file creation and deletion are in
sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function w83795_probe() is way too big, move file creation to a separate
function to make it more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Sysfs files must be removed on device removal but also when device
registration fails. Move the code to a separate function to avoid
code redundancy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the bank selection code to a separate function, to avoid
duplicating it in read and write functions. Improve error reporting
on register access error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enum chips and chip_types are redundant, get rid of the former. Fix
the detection code to properly identify the chip variant and name the
client accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is still much work needed, but I wanted to give Wei the credit
he deserves. I've merged some of my own fixes already, to make
gcc and checkpatch happy. Individual fixes and improvements from me
will follow.
[JD: Fix build errors]
[JD: Coding style cleanups]
[JD: Get rid of forward declarations]
[JD: Drop VID support]
[JD: Drop fault output control feature]
[JD: Use lowercase for inline function names]
[JD: Use strict variants of the strtol/ul functions]
[JD: Shorten the read and write function names]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This way we don't need to modify Kconfig every time a new SoC comes along to
make this driver support it. Also fix some typos while I'm at it.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The semaphore which protects the ADC is semantically a mutex. Use a
real mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we get the checkpatch warning
consider using strict_strtol in preference to simple_strtol.
Also we should not allow any partially numeric values.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I was wondering if that chip ever existed publicly... Apparently yes,
so add support for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Instead of using switch/case and if statements in probe, define chip specific
functionality in a parameter structure array.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The family check in k8temp is not required because the driver is
already bound to a northbridge device only used with K8 CPUs.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
All axis enable bits are set to 0 at module remove.
Restore reset default value at init.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.
Input device open and close functions set status for
interrupt threaded handler once.
Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.
Feature is optional and must be enabled in platform data.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.
spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.
For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds hwmon support for fans connected to GPIO lines.
Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).
v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard. When each new model appears, users need to
adjust again. Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.
This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver. User can pass the
parameter such as axes=3,2,1. Also it can be changed via sysfs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.
Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A new version of LIS3 chip has slight incompatibilities from former
versions. This patch adds the minimal support for it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
... as they're being called only from a __cpuinit function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
eeepc-wmi: Add cpufv sysfs interface
eeepc-wmi: add additional hotkeys
panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
panasonic-laptop: Handle errors properly if they happen
intel_pmic_gpio: fix off-by-one value range checking
IBM Real-Time "SMI Free" mode driver -v7
Add OLPC XO-1 rfkill driver
Move hdaps driver to platform/x86
ideapad-laptop: Fix Makefile
intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
ideapad: Add param: no_bt_rfkill
ideapad: Change the driver name to ideapad-laptop
ideapad: rewrite the sw rfkill set
ideapad: rewrite the hw rfkill notify
ideapad: use EC command to control camera
ideapad: use return value of _CFG to tell if device exist or not
ideapad: make sure we bind on the correct device
ideapad: check VPC bit before sync rfkill hw status
ideapad: add ACPI helpers
dell-laptop: Add debugfs support
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
The hdaps driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/platform/x86 seems much more
appropriate, as the driver is only useful on x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sleep while acquiring a resource lock on the Super I/O port. This should
prevent collisions from causing the hardware probe to fail with -EBUSY.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Commit e40cc4bdfd introduced
a build breakage if CONFIG_SMP is undefined. This commit
fixes the problem.
This fix is only a workaround. For a real fix, cpu_sibling_mask() should
be defined in UP include code, eg in linux/smp.h, and asm/smp.h should not be
included directly. This fix is currently not possible because asm/smp.h defines
cpu_sibling_mask() unconditionally and is included directly from many source
files.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Other than coretemp, from which this code was apparently derived, there
is no PCI specific code in this driver.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like pkgtemp registers another core of the same package when one
gets removed, coretemp should register another hyperthread (if
available) in that situation.
As pointed out in the patch fixing the respective code in pkgtemp, the
list protectng mutex must be dropped before calling
coretemp_device_add(), and due to the restructured loop (including an
explicit return) the "safe" variant of the list iterator isn't needed
anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Feature availability should also be checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp_device_remove(), holding the list protecting mutex, calls
pkgtemp_device_add(), which itself wants to acquire the same mutex.
Holding the mutex over the entire loop body in pkgtemp_device_remove()
isn't really necessary, as long as the loop gets exited after
processing the matched CPU.
Once exiting the loop after removing an eventual match, there's no
need for using the "safe" list iterator anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In commit 0dca94baea the call to
platform_driver_unregister() was made conditional upon !HOTPLUG_CPU,
but the return value from coretemp_init() was left to indicate an
error. This isn't correct, as the negative return value indicates to
the module loader that initialization failed, which isn't intended
here and results in dangling pointers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent addition of threaded irq handler causes a NULL dereference
when used with hp_accel driver, which has NULL pdata.
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
update_interval is the matching attribute defined in the hwmon sysfs ABI.
Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
According to the datasheet for Winbond W83627DHG the proper way to exit
the Extended Function Mode is to write 0xaa to the EFER(0x2e or 0x4e).
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is unnecessary and wrong to call hwmon_device_unregister in error
handling before hwmon_device_register is called.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All bits in the values read from registers to be used for the next
write were getting overwritten, avoid doing so to not mess with the
current configuration.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The spec notes that fan0 and fan1 control mode bits are located in bits
7-6 and 5-4 respectively, but the FAN_CTRL_MODE macro was making the
bits shift by 5 instead of by 4.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If CONFIG_PM was selected and lis3lv02d_platform_data was NULL,
the kernel will be panic when halt command run.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Sigend-off-by: Jean Delvare <khali@linux-fr.org>
Added missing axis-mapping for HP ProBook 532x and HP Mini 5102.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The via-cputemp hwmon driver was probably intending "typedef enum {
... } SHOW;", but the "typedef" was missing creating a global variable
named "SHOW". There is absolutely no reason to have this in the
global namespace.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
jc42 uses i2c interfaces, so it should depend on I2C.
drivers/hwmon/jc42.c:426: error: implicit declaration of function 'i2c_check_functionality'
drivers/hwmon/jc42.c:521: error: implicit declaration of function 'i2c_smbus_read_word_data'
drivers/hwmon/jc42.c:529: error: implicit declaration of function 'i2c_smbus_write_word_data'
drivers/hwmon/jc42.c:580: error: implicit declaration of function 'i2c_add_driver'
drivers/hwmon/jc42.c:585: error: implicit declaration of function 'i2c_del_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
