Add interface ID information to the tail of each transmitted packet
so that firmware can know to which interface the packet belongs to.
This is only needed if device supports HW switch capability.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports that it supports hardware switch capabilities,
driver needs to track and notify device whenever broadcast domain
of a particular network device changes (ie. whenever it's upper
master device changes).
Firmware needs a unique ID to tell broadcast domains from each other
which is an opaque number otherwise. For that purpose we can use
netspace:ifidx pair to uniquely identify each broadcast domain:
- if netdev is not part of a bridge, then use it's own ifidx
as a broadcast domain ID
- if netdev is part of a bridge, then use bridge netdev ifidx
as broadcast domain ID
Firmware makes sure that packets are only forwarded between
interfaces marked with the same broadcast domain ID.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in case of error when registering network device with the
kernel, we won't properly cleanup VIF state in firmware due to DEL_VIF
command will not be send to wifi card. Make sure it does.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since read RF register is an indirect access that hardware needs time to
accomplish read action, but there's no ready bit, so delay is required to
guarantee the read value is correct. After investigating internal documents,
these delays are reduced as proper values.
Reported-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rf_lock is used to protect RF register access, but they will not called
from interrupt context, so *_irqsave version isn't necessary. Then, these
delays don't affect IRQ services.
The old code holds spin_lock_irqsave() that will be detected a long delay
as below:
kworker/-276 4d... 0us : _raw_spin_lock_irqsave
kworker/-276 4d... 0us : rtl8723_phy_rf_serial_read <-rtl8723de_phy_set_rf_reg
kworker/-276 4d... 1us : rtl8723_phy_query_bb_reg <-rtl8723_phy_rf_serial_read
kworker/-276 4d... 3us : rtl8723_phy_set_bb_reg <-rtl8723_phy_rf_serial_read
kworker/-276 4d... 4us : __const_udelay <-rtl8723_phy_rf_serial_read
kworker/-276 4d... 4us!: delay_mwaitx <-rtl8723_phy_rf_serial_read
kworker/-276 4d... 1004us : rtl8723_phy_set_bb_reg <-rtl8723_phy_rf_serial_read
[...]
Reported-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/intel/ipw2x00/ipw2100.c: In function shim__set_security:
drivers/net/wireless/intel/ipw2x00/ipw2100.c:5582:9: warning: variable force_update set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/intel/ipw2x00/ipw2200.c: In function ipw_wx_set_mlme:
drivers/net/wireless/intel/ipw2x00/ipw2200.c:6805:9: warning: variable reason set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of multiplying by page order, virtio balloon divided by page
order. The result is that it can return 0 if there are a bit less
than MAX_ORDER - 1 pages in use, and then shrinker scan won't be called.
Cc: stable@vger.kernel.org
Fixes: 71994620bb ("virtio_balloon: replace oom notifier with shrinker")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
virtio_balloon_shrinker_scan should return number of system pages freed,
but because it's calling functions that deal with balloon pages, it gets
confused and sometimes returns the number of balloon pages.
It does not matter practically as the exact number isn't
used, but it seems better to be consistent in case someone
starts using this API.
Further, if we ever tried to iteratively leak pages as
virtio_balloon_shrinker_scan tries to do, we'd run into issues - this is
because freed_pages was accumulating total freed pages, but was also
subtracted on each iteration from pages_to_free, which can result in
either leaking less memory than we were supposed to free, or more if
pages_to_free underruns.
On a system with 4K pages we are lucky that we are never asked to leak
more than 128 pages while we can leak up to 256 at a time,
but it looks like a real issue for systems with page size != 4K.
Fixes: 71994620bb ("virtio_balloon: replace oom notifier with shrinker")
Reported-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_get_regaddr:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:790:5: warning: variable mpnum set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:10: warning: variable nsp set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:5: warning: variable nmp set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the bnx2fc_eh_abort() function there is a calculation for
wait_for_completion that uses a HZ multiplier. This is incorrect, it
scales the timeout by 1000 seconds instead of converting the ms value to
jiffies. Therefore change the calculation.
Link: https://lore.kernel.org/r/1574178394-16635-1-git-send-email-loberman@redhat.com
Reported-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Chad Dupuis <cdupuis1@gmail.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 075e238d12.
Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.
This patch fixes this wrong bit mask.
Fixes: 2336f19d78 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.
This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.
Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation on phylink's create and destroy functions to
explicitly state that the rtnl lock must not be held while calling
these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the string for which conversion failed instead of printing the
function name twice.
Fixes: 2650d71e24 ("target: move transport ID handling to the core")
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20191107215525.64415-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The iSCSI target driver is the only target driver that does not wait for
ongoing commands to finish before freeing a session. Make the iSCSI target
driver wait for ongoing commands to finish before freeing a session. This
patch fixes the following KASAN complaint:
BUG: KASAN: use-after-free in __lock_acquire+0xb1a/0x2710
Read of size 8 at addr ffff8881154eca70 by task kworker/0:2/247
CPU: 0 PID: 247 Comm: kworker/0:2 Not tainted 5.4.0-rc1-dbg+ #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: target_completion target_complete_ok_work [target_core_mod]
Call Trace:
dump_stack+0x8a/0xd6
print_address_description.constprop.0+0x40/0x60
__kasan_report.cold+0x1b/0x33
kasan_report+0x16/0x20
__asan_load8+0x58/0x90
__lock_acquire+0xb1a/0x2710
lock_acquire+0xd3/0x200
_raw_spin_lock_irqsave+0x43/0x60
target_release_cmd_kref+0x162/0x7f0 [target_core_mod]
target_put_sess_cmd+0x2e/0x40 [target_core_mod]
lio_check_stop_free+0x12/0x20 [iscsi_target_mod]
transport_cmd_check_stop_to_fabric+0xd8/0xe0 [target_core_mod]
target_complete_ok_work+0x1b0/0x790 [target_core_mod]
process_one_work+0x549/0xa40
worker_thread+0x7a/0x5d0
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Allocated by task 889:
save_stack+0x23/0x90
__kasan_kmalloc.constprop.0+0xcf/0xe0
kasan_slab_alloc+0x12/0x20
kmem_cache_alloc+0xf6/0x360
transport_alloc_session+0x29/0x80 [target_core_mod]
iscsi_target_login_thread+0xcd6/0x18f0 [iscsi_target_mod]
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Freed by task 1025:
save_stack+0x23/0x90
__kasan_slab_free+0x13a/0x190
kasan_slab_free+0x12/0x20
kmem_cache_free+0x146/0x400
transport_free_session+0x179/0x2f0 [target_core_mod]
transport_deregister_session+0x130/0x180 [target_core_mod]
iscsit_close_session+0x12c/0x350 [iscsi_target_mod]
iscsit_logout_post_handler+0x136/0x380 [iscsi_target_mod]
iscsit_response_queue+0x8de/0xbe0 [iscsi_target_mod]
iscsi_target_tx_thread+0x27f/0x370 [iscsi_target_mod]
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
The buggy address belongs to the object at ffff8881154ec9c0
which belongs to the cache se_sess_cache of size 352
The buggy address is located 176 bytes inside of
352-byte region [ffff8881154ec9c0, ffff8881154ecb20)
The buggy address belongs to the page:
page:ffffea0004553b00 refcount:1 mapcount:0 mapping:ffff888101755400 index:0x0 compound_mapcount: 0
flags: 0x2fff000000010200(slab|head)
raw: 2fff000000010200 dead000000000100 dead000000000122 ffff888101755400
raw: 0000000000000000 0000000080130013 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881154ec900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881154ec980: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8881154eca00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881154eca80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881154ecb00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
Cc: Mike Christie <mchristi@redhat.com>
Link: https://lore.kernel.org/r/20191113220508.198257-3-bvanassche@acm.org
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since it is nontrivial to derive the meaning of the size argument from the
code, add a documentation header above target_cmd_size_check().
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Link: https://lore.kernel.org/r/20191107215458.64242-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The member hba->pcidev may be used after its reference is dropped. Move the
put function to where it is never used to avoid potential use after free
issues.
Fixes: a771718065 ("[SCSI] bnx2i: Removed the reference to the netdev->base_addr")
Link: https://lore.kernel.org/r/1573043541-19126-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 2f856d4e8c.
This patch was found to introduce a double free regression. The issue
it originally attempted to address was fixed in patch
f45bca8c50 ("scsi: qla2xxx: Fix double scsi_done for abort path").
Link: https://lore.kernel.org/r/4BDE2B95-835F-43BE-A32C-2629D7E03E0A@marvell.com
Requested-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a module parameter to inhibit disconnect/reselect for individual
targets. This gains compatibility with Aztec PowerMonster SCSI/SATA
adapters with buggy firmware. (No fix is available from the vendor.)
Apparently these adapters pass-through the product/vendor of the attached
SATA device. Since they can't be identified from the response to an INQUIRY
command, a device blacklist flag won't work.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Link: https://lore.kernel.org/r/993b17545990f31f9fa5a98202b51102a68e7594.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When do_abort() succeeds, the target will go to BUS FREE phase and there
will be no connected command. Therefore, that function should clear the
Initiator Command Register before returning. It already does so in case of
NCR5380_poll_politely() failure; do the same for the other error case too,
that is, NCR5380_transfer_pio() failure.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/4277b28ee2551f884aefa85965ef3c498344f301.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most NCR5380 drivers calculate the residual for every data transfer.
(A few drivers just set it to zero.) Pass this quantity back to the scsi
mid-layer on command completion.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/1f26ead9dd0dc053fcd27979d69a7ca74b6589b4.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Passing the parameter "num_tgts=-1" will start an infinite loop that
exhausts the system memory
Link: https://lore.kernel.org/r/20191115163727.24626-1-mlombard@redhat.com
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Looking at the recent conversion from smp_processor_id() to
raw_smp_processor_id(), realized that the allocation should be based on the
cpu the hdwq is bound to, not the executing cpu.
Revise to pull cpu number from the hdwq
Fixes: 765ab6cdac ("scsi: lpfc: Fix a kernel warning triggered by lpfc_get_sgl_per_hdwq()")
Link: https://lore.kernel.org/r/20191116003847.6141-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable init_fw_cb is released twice, resulting in a double free
bug. The call to the function dma_free_coherent() before goto is removed to
get rid of potential double free.
Fixes: 2a49a78ed3 ("[SCSI] qla4xxx: added IPv6 support.")
Link: https://lore.kernel.org/r/1572945927-27796-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the correct method to collect the fatal dump.
Link: https://lore.kernel.org/r/20191114100910.6153-14-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With MSI-x enabled, the interrupt instances are <prefix><index> where the
prefix is fixed for all module instances, making it a little harder to
track down what's what.
Link: https://lore.kernel.org/r/20191114100910.6153-13-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to check controller fatal error through sysfs.
Link: https://lore.kernel.org/r/20191114100910.6153-12-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Occasionally, 6G capable drives fail to train at 6G on links that look good
from a signal-integrity perspective. PMC suggests configuring the port to
not even expect 12G.
Link: https://lore.kernel.org/r/20191114100910.6153-11-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the fix so the if driver properly sent the abort it tries to remove
it from the firmware's list of outstanding commands regardless of the abort
status. This means that the task gets freed 'now' rather than possibly
getting freed later when the scsi layer thinks it's leaked but still valid.
Link: https://lore.kernel.org/r/20191114100910.6153-10-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task structure should not be used after task_done is called. If the
device is gone or not attached, we call task_done on t and continue to use
in the sas_task in rest of the function. task_done is pointing to
sas_ata_task_done, may free the memory associated with the task before
returning.
Link: https://lore.kernel.org/r/20191114100910.6153-8-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpi_uninit_check takes longer for inbound doorbell register to
be cleared. Increased the timeout substantially so that the driver does not
fail to load.
Link: https://lore.kernel.org/r/20191114100910.6153-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: ianyar <ianyar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default logging doesn't include the device name, so it's difficult to
determine which controller is being logged about in error scenarios. The
logging level was only settable via sysfs, which made it inconvenient for
actual debugging. This changes the default to only cover error handling.
Link: https://lore.kernel.org/r/20191114100910.6153-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For delays longer than 20ms [um]delay isn't recommended.
pm80xx_chip_soft_rst starts off with a 500ms delay before it even gets
around to checking for the results of the reset. As long as it's at least
500ms it doesn't matter what the scheduler is doing. The delay in the
pm8001_exec_internal_task_abort does nothing, and theory is this is a delay
to avoid a double-free.
Link: https://lore.kernel.org/r/20191114100910.6153-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_task_exec(), if the PHY is down, then we return the current value
of 'rc'. We need to make sure it's initialized.
Link: https://lore.kernel.org/r/20191114100910.6153-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the completing the mpi_phy_start_resp, make phy enable completion as
NULL.
Link: https://lore.kernel.org/r/20191114100910.6153-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was missing complete() call in mpi_sata_completion which result in
SATA abort error handling timing out. That causes the device to be left in
the in_recovery state so subsequent commands sent to the device fail and
the OS removes access to it.
Link: https://lore.kernel.org/r/20191114100910.6153-2-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During clock gating (ufshcd_gate_work()), we first put the link hibern8 by
calling ufshcd_uic_hibern8_enter() and if ufshcd_uic_hibern8_enter()
returns success (0) then we gate all the clocks. Now let’s zoom in to what
ufshcd_uic_hibern8_enter() does internally: It calls
__ufshcd_uic_hibern8_enter() and if failure is encountered, link recovery
shall put the link back to the highest HS gear and returns success (0) to
ufshcd_uic_hibern8_enter() which is the issue as link is still in active
state due to recovery! Now ufshcd_uic_hibern8_enter() returns success to
ufshcd_gate_work() and hence it goes ahead with gating the UFS clock while
link is still in active state hence I believe controller would raise UIC
error interrupts. But when we service the interrupt, clocks might have
already been disabled!
This change fixes for this by returning failure from
__ufshcd_uic_hibern8_enter() if recovery succeeds as link is still not in
hibern8, upon receiving the error ufshcd_hibern8_enter() would initiate
retry to put the link state back into hibern8.
Link: https://lore.kernel.org/r/1573798172-20534-8-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change attempts to abort gating of clocks if a request to turn-on
clocks is pending. This would in turn avoid turning OFF and back ON the
clocks.
Link: https://lore.kernel.org/r/1573798172-20534-7-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return IRQ_HANDLED only if the irq is really handled, this will help in
catching spurious interrupts that go unhandled.
Link: https://lore.kernel.org/r/1573798172-20534-6-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
kernel/bpf/arraymap.c:481:5: warning:
symbol 'array_map_mmap' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191119142113.15388-1-yuehaibing@huawei.com
With the most recent Clang, alu32 is enabled by default if -mcpu=probe or
-mcpu=v3 is specified. Use a separate build rule with -mcpu=v2 to enforce no
ALU32 mode.
Suggested-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191120002510.4130605-1-andriin@fb.com
