The Cavium Thunder SoCs have multiple MIDO buses that are part of a
single PCI device. To model this in the device tree we call the PCI
parent device a "cavium,thunder-8890-mdio-nexus", it has several
children, one for each MDIO bus.
The MDIO bus hardware is identical to that found in the OCTEON SoCs,
so we use that code for things that are not part of the PCI driver
probe/remove
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-on patch uses PCI probing to find the Thunder MDIO hardware.
In preparation for this, split out the common code into a new file
mdio-cavium.c, which will be used by both the existing OCTEON driver,
and the new Thunder PCI based driver.
As part of the refactoring simplify the struct cavium_mdiobus by
removing fields that are only ever used in the probe function and can
just as well be local variables.
Use readq/writeq in preference to readq_relaxed/writeq_relaxed as the
relaxed form was an optimization for an early chip revision, and the
MDIO drivers are not performance bottlenecks that need optimization in
the first place.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83848 Ethernet PHY device.
The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant
single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting
the MII and RMII interfaces.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom iProc MDIO bus interface.
The MDIO interface can be found in the Broadcom iProc family Soc's.
The MDIO bus is accessed using a combination of command and data
registers. This MDIO driver provides access to the Etherent GPHY's
connected to the MDIO bus.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Microchip LAN88XX phy driver for phylib.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Teranetics TN2020 is compliant with IEEE 802.3an 10 Gigabit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we get things like:
warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)
In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
This patch adds an MDIO driver which handles the MII bus.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Frederic Lambert <frdrc66@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This is the first version of phy driver from Micrel Inc.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
this PHY present on the MPC8315E and MPC837xE RDB boards.
Signed-off-by: Johnson Leung <r58129@freescale.com>
Signed-off-by: Kevin Lam <r43770@freescale.com>
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, bitbanged MDIO was only supported in individual
hardware-specific drivers. This code factors out the higher level
protocol implementation, reducing the hardware-specific portion to
functions setting direction, data, and clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition
to a dedicated 100Mbit/s WAN port.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for interrupt-driven operation of the Broadcom
Gigabit Ethernet PHYs. I have included device IDs for the parts used on
Broadcom SiByte evaluation boards; more can be added as a need arises.
They are apparently generally software-compatible with one another.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-broadcom-phy-15
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds back the code that was taken out, thus re-enabling:
* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer
This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
