Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
of all mbox registers in aen_q
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
remove ha flag AF_HBA_GOING_AWAY and added flag AF_HA_REMOVAL
to mark the other ISP-4xxx port to indicate that the driver is
being removed, so that the other port will not re-initialize
while in the process of removing the ha due to driver unload
or hba hotplug.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver has capability to add device dynamically and present
them to OS, driver no longer need to wait for DDBs to come
online during driver initialization.
Driver still issues a relogin for DDBs that are not online,
but no longer wait for DDB to come online.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prior to firmware state change from ACQUIRING to READY, an
0x8029 AEN is received. Added code to check previous state
being ACQUIRING in order to update the ip address in the driver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI since
this interrupt mechanism cannot be shared like standard INTx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_DISABLE flag is deprecated and this flag is a NOOP in kernel.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
AEN 8130 Corresponds to an event representing the insertion (detection)
of a transceiver. It also reports the type of the SFP+.
AEN 8131 corresponds to the removal of a transceiver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
change data type of sense_len from uint8_t to uint16_t
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Per RFC 3720, Login Response Status Code 0x02 should not be retried.
Condensed connection error checking code to a single routine, and
added check for status class 0x02.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Link Down -> Mark all devices missing
Previously, the driver took no action on a Link Down,
and waited for the I/O on a dead connection to timeout
in the firmware before marking the DDB missing.
Link Up -> Mark all devices online
F/W will do auto login to all the devices only once.
After that its the responsibility of the driver to
relogin to devices whenever there is :
* Any sort of connection failure or
* KATO expires indicating target has logged out or
* I/O times out etc.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The residual variable is only valid for udnerrun so do
not print it out for the overrun case.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[Mike Christie: Fix coding style issues in patch]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications. Sense data
in the first 32 bytes has always been correct.
Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.
Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.
Changed version number to 5.01.00-k9
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the iscsi drivers to the new host byte values.
v2
Drop some conversions. Want to avoid conflicts with other patches.
v1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch contains the following:
1. when hba completion status is good, check for iscsi transport
errors (underflow/overflow) prior to checking the scsi status
2. New firmware requires that one marker iocb be issued for each task
management command. The patch issues marker iocb immediately
following a LUN or Target reset.
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Wed, 2007-06-06 at 11:55 -0700, David C Somayajulu wrote:
This patch fixes the code handling underrun and overrun conditions.
Also fixed coding style as per Mike Christie's advice.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to log all AENs and service mbx cmd completions for QLA4032
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The included patch fixes the following issues:
1. qla3xxx/qla4xxx co-existence issue which can result in a lockup
when qla3xxx driver is unloaded, or when ifdown; ifup is performed on
one of the interfaces correponding to qla3xxx. This is because qla4xxx
HBA supports one ethernet and iscsi interfaces per port. Both iscsi
and ethernet interfaces share the same state machine. The problem has
to do with synchronizing access to the state machine in the event of a
reset
2. mutex_lock() is sometimes not followed by mutex_unlock() prior to
invoking a msleep() in qla4xxx_mailbox_command()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch provides the following:
1. adds support for the next version of Qlogic's iSCSI HBA, qla4032
(PCI Device ID 4032).
2. removes dead code related to topcat chip and renames
qla4010_soft_reset to qla4xxx_soft_reset (minor changes).
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
