Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Seems the commit 7e89098 was overly aggressive in adding iva and mailbox
hwmods so now they are registered twice.
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: iva: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: mailbox: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 HWMOD data currently contains these errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_dsi is missing ick and sys_clk
- dss_venc is missing dss_96m_fck opt-clock, which is required on
OMAP3430
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
dss_core's opt-clocks is also missing dss_96m_fck, which is a DSS clock
present only on OMAP3430, and thus required on OMAP3430 to finish the
reset.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET and adds the dss_96m_fck
opt-clock for dss_core in OMAP3 HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit d6504acd21 ("OMAP2+: hwmod:
remove OMAP_CHIP*") tests the inverse condition of what it should be
testing for the return value from omap_hwmod_register(). This causes
several IP blocks to not be registered on several OMAP3 family devices.
Fixing that bug also unmasked another bug, originally reported by
Chase Maupin <chase.maupin@ti.com> and then subsequently by Abhilash K
V <abhilash.kv@ti.com>, which caused SmartReflex IP blocks to be
registered on SoCs that don't support them.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for comments
on a previous version of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Chase Maupin <chase.maupin@ti.com>
Cc: Abhilash K V <abhilash.kv@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
Removing modules iva, sr1_hwmod, sr2_hwmod, mailbox from
the base omap3xxx_hwmods list, so that they can be excluded
for am35x. This removes quite a few warnings on boot for AM35x.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[paul@pwsan.com: dropped 'mailbox class' comments; updated changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This voltage domain (a.k.a. VDD1) contains both the MPU and the IVA, so
rename appropriately.
Also fixup any users of the "mpu" name to use "mpu_iva"
Signed-off-by: Kevin Hilman <khilman@ti.com>
At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.
Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
- Disable the I2C.
- Write to SOFTRESET bit.
- Enable the I2C.
- Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer. omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
offset conditional code to use the IP block revision; minor code
cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on. We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Peter Maydell noticed when running under QEMU he was getting
errors reporting 32-bit access to I2C peripheral unit registers
that are documented to be 8 or 16-bit only[1][2]
The I2C driver is blameless as it wraps its accesses in a
function using __raw_writew and __raw_readw, it turned out it
is the hwmod stuff.
However the hwmod code already has a flag to force a
perhipheral unit to only be accessed using 16-bit operations.
This patch applies the 16-bit only flag to the 2430,
OMAP3xxx and OMAP44xx hwmod structs. 2420 was already
correctly marked up as 16-bit.
The 2430 change will need testing by TI as arranged
in the comments to the previous patch version.
When the 16-bit flag is or-ed with other flags, it is placed
first as requested in comments.
[1] OMAP4430 Technical reference manual section 23.1.6.2
[2] OMAP3530 Techincal reference manual section 18.6
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To reduce kernel source file data duplication, share struct
omap_hwmod_class and omap_hwmod_class_sysconfig arrays across OMAP2xxx
and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To reduce kernel source file data duplication, share struct
omap_hwmod_dma_info arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To reduce kernel source file data duplication, share struct
omap_hwmod_mpu_irqs arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To reduce kernel source file data duplication, share struct
omap_hwmod_addr_space arrays across OMAP2xxx and 3xxx hwmod data
files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPIO module expects the debounce clocks to be enabled during reset. It doesn't
reset properly and timeouts are seen, if this clock isn't enabled during
reset. Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flags to the GPIO HWMODs, with
which the debounce clocks are enabled during reset.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2420, 2430 and 3xxx were using the OMAP4 end address
that unfortunately is not located at the same base address.
Moreover the OMAP4 size was set to 256 instead of 4096.
Change all .pa_end to set them to .pa_start + 0xfff
Cc: "G, Manjunath Kondaiah" <manjugk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reported-by: Michael Fillinger <m-fillinger@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.
On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.
On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.
Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.
Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.
The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.
This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.
This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.
This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap3 hwmod data with the HSMMC info.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Since the sidetone block is tightly coupled to the mcbsp, sidetone information
is directly added to mcbsp2 & 3 hwmod dev_attr.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP3.
Added a revision member inorder to facilitate the driver to
differentiate between mcbsp in different omap.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mailbox hwmod data for omap3.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for Display Sub System applicable for OMAP3430 and
OMAP36xx. DSS is also considered as an IP as DISPC, RFBI and named as dss_core.
For all the IP modules in DSS, same clock is needed for enabling. Hwmod sees
DSS IPs as independent IPs, so same clock has to be repeated for .main_clk in
each IP.
This patch defines separate hwmod databases for OMAP3430ES1 and (OMAP3430ES2 and
OMAP36xx) as OMAP3430ES1 does not have IDLEST bit to poll on for dss IP, and also
the firewall regions are different between 3430es1 and later.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
