Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code. Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVMUpdate tool doesn't necessarily know the ReadOnly map of the current
NVM image, and must try reading and writing words that may be protected.
This generates an error out of the Firmware request that the driver logs.
Unfortunately, this ends up spitting out hundreds of bogus read and write
error message that looks rather messy.
This patch checks the error type and under normal conditions will not print
the typical read and write errors during NVMUpdate. This can be overridden
by enabling the NVM update debugging. This results in a much less messy log
file, and likely many fewer customer support questions.
Change-ID: Id4ff2e9048c523b0ff503aa5ab181b025ec948ea
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.
The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.
Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.
Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.
Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the sizeof() calls are taking the size of the actual struct
that we care about. By using the pointer variable, we'll always get
the right struct size, even if the variable type changes sometime in
the future.
Change-ID: Id5858f883cf42447365ea3733080d7714f975bce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While using the Linux "strings" command I found these two strings in the
driver. There's no need for them and they're kinda silly.
Change-ID: I4e19b02983d48b631e9a9979f49790492845f221
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of configfs is not allowed in network drivers. Strip the code that
uses it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.12 and i40evf to 1.2.6.
Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.
Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.
Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use l4_tunnel type generically to keep code flow simple.
Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.
If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.
If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.
ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.
Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.
Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only print the port and veb stats if this is the first partition
of a multiplexed port.
Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.
Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition. This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny. Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.
Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.
Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.
This fixes the sparse warning and fixes up the other issues.
Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16. Fix the width of the datatype.
Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.
Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This series of code was repeated twice, remove one of them.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.
Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.
Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
[...]
Call Trace:
[<ffffffff81195445>] put_page+0x55/0x60
[<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
[<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
[<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
[<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
[<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
[<ffffffff81647050>] dev_set_mtu+0xa0/0x140
[<ffffffff81664218>] do_setlink+0x218/0xac0
[<ffffffff814459e9>] ? nla_parse+0xb9/0x120
[<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
[<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
[<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260
By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers. The allocator is set back to a sane value in
e1000_configure_rx.
Fixes: edbbb3ca10 ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While addressing the pin problem I noticed that all of the pin register
values where having to be pushed onto the stack each time the function was
called. To avoid that I am making them static const so that they should
only need to be allocated once and we can avoid all the instructions to get
them onto the stack..
size before:
text data bss dec hex filename
161477 10512 8 171997 29fdd drivers/net/ethernet/intel/igb/igb.ko
size after:
text data bss dec hex filename
161205 10512 8 171725 29ecd drivers/net/ethernet/intel/igb/igb.ko
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When building the kernel using the gcc 4.8.3 compiler included in Fedora 20
I was repeatedly seeing the warning:
drivers/net/ethernet/intel/igb/igb_ptp.c: In function ‘igb_ptp_feature_enable_i210’:
drivers/net/ethernet/intel/igb/igb_ptp.c:395:21: warning: ‘pin’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
tssdp &= ~ts_sdp_en[pin];
^
drivers/net/ethernet/intel/igb/igb_ptp.c:471:6: note: ‘pin’ was declared here
int pin;
^
To resolve it I am assigning the pin a value of -1 when it is instantiated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar. The mapping/unmapping is relevant
to older HW only.
CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interface to the device flash was modified in i219 and later HW.
This patch better describes the change and the impact on the driver.
CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver spams the system log with messages about VF VSI when VFs
are created, as well as each time they are reset. This is annoying, and
the information isn't even useful most of the time.
Remove this message to reduce user annoyance.
Change-ID: I8de90d05380f54b038c9c8c3265150be87c9242c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown. This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.
Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.
Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.
Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the 10G and 40G AOC PHY types to the case statement in get_media_type
and ethtool get_settings so that the correct information gets reported
back to the user.
Change-ID: I1b4849d22199a9acf7c8807166d0317c1faad375
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the system administrator is requesting an offline diagnostic test using
'ethtool -t' then we should, you know, actually take the device offline
before doing the testing.
Change-ID: I6afa1cbfcc821c9ab6e6f47ed4d8dc2d8dd20e82
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some FW versions are incorrectly reporting a breakout cable as PHY type
0x3 when it should be 0x16 (I40E_PHY_TYPE_10GBASE_SFPP_CU).
If we get this value back from FW and the version is < 4.40, reassign it
to I40E_PHY_TYPE_10GBASE_SFPP_CU.
Change-ID: Ibb41a0e3cd2c0753744e8553959240df6ed13ae8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.
This caused higher CPU utilization and had some other performance impacts
for transmit tests.
Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use automatic sign extension by replacing 0xffff... constants
with ~(u64)0 or ~(u32)0.
Change-ID: I73cab4cd2611795bb12e00f0f24fafaaee07457c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.
Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In CEE mode the firmware does not set the operational status bit of
the application TLV status as returned from the "Get CEE DCBX Oper Cfg"
AQ command. This occurs whenever a DCBX configuration is changed.
This is a workaround to remove the check for the operational and sync bits
of the application TLV status till a firmware fix is provided.
Change-ID: I1a31ff2fcadcb06feb5b55776a33593afc6ea176
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify our get and set LED functions so they ignore activity LEDs,
as we are required to blink the link LEDs only.
Change-ID: I647ea67a6fc95cbbab6e3cd01d81ec9ae096a9ad
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to the driver initialization have caused the BW
configurations to not take effect. We use a BW configuration read and
write back to "kick" the Tx scheduler into action.
Change-ID: I94ab377c58d3a3986e3de62b6c199be3fd2ee5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-03
This series contains updates to fm10k, i40e and i40evf.
Matthew updates the fm10k driver by cleaning up code comments and whitespace
issues. Also modifies the tunnel length header check, to make it more robust
by calculating the inner L4 header length based on whether it is TCP or UDP.
Implemented ndo_features_check() that allows drivers to report their offload
capabilities per-skb.
Neerav updates the i40e driver to skip over priority tagging if DCB is not
enabled. Fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local DCBX
application configuration TLVs. Fixed i40e where, in the case of MFP
mode, the driver was returning the incorrect number of traffic classes
for partitions that are not enabled for iSCSI. Even though the driver
was not configuring these traffic classes in the transmit scheduler for
the NIC partitions, it does use this map to setup the queue mappings.
Shannon updates i40e/i40evf to include the firmware build number in the
formatted firmware version string.
Akeem adds a safety net (by adding a 'default' case) for the possible
unmatched switch calls.
Mitch updates i40e to not automatically disable PF loopback at runtime,
now that we have the functionality to enable and disable PF loopback. This
fix cleans up a bogus error message when removing the PF module with VFs
enabled. Adds a extra check to make sure that the indirection table
pointer is valid before dereferencing it.
Anjali enables i40e to enable more than the max RSS qps when running in a
single TC mode for the main VSI. It is possible to enable as many as
num_online_cpus(). Adds a firmware check to ensure that DCB is disabled for
firmware versions older than 4.33. Updates i40e/i40evf to add missing
packet types for VXLAN offload. Updated i40e to be able to handle varying
RSS table size for each VSI, since all VSI's do not have the same RSS table
size.
v2: Dropped previous patch #9 "i40e/i40evf: Add capability to gather VEB
per TC stats" since the stats should be in ethtool and not debugfs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module dependencies are broken in the case where CONFIG_I40E=y and
CONFIG_CONFIGFS_FS=m. This fixes the broken dependency.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.
This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.
Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.
Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.
Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.
Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.
Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size
Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were missing a few packet types for VXLAN offload. This patch fixes
that.
Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.
Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.
Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This patch makes it possible to
enable as many as num_online_cpus().
ethtool -L can still be used to reconfigure number of qps
to a smaller value.
Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.
Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds default case to handle unmatched switch calls.
Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include the FW build number in the formatted FW version string. In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version. This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.
Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCB is not enabled priority tagging is not needed
so skip over that section.
Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.
Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.
Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we don't try to dereference NULL pointers when returning values
from the AdminQ calls.
Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, a multi-write transaction takes longer than the
default 3 minute timeout on the write semaphore. If the write failed with
an EBUSY status, this is likely the problem, so here we try to reacquire
the semaphore then retry the write. We only do one retry, then give up.
Change-ID: I1c8be60688acc2f39573839579baf601207c4a36
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine the ICR0 shutdown with the standard interrupt shutdown, and
add the interrupt clearing to the PCI shutdown path.
This prevents the driver from allowing stray interrupts or causing
system logs from un-handled interrupts.
Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were checking the outer Protocol flags and deciding the flow for
inner header. This patch fixes that.
This fixes the Tx checksum offload for TCP/IPv6 over vxlan.
Change-ID: I837aaea921d34f71b24c2bc32aaadea5001ddf78
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of DCB reconfiguration flow if the Tx queue disable times out
then issue a PF reset to do some level of recovery.
Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is reconfigured to single TC the driver did not reset the
Tx ring Qset handle to the correct mapping; which caused Tx queue
disable timeouts.
Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver or hardware gets less interrupt vectors than the actual
number of CPU cores, limit the queue count for the priority queue
traffic class (TC) queues.
This will fix a warning with multiple function mode where systems
regularly have more cores than vectors.
Also add extra comment for readability.
Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was having some issues with false Tx hang detection. This
makes the driver a little more direct with the checks for progress
forward by directly checking the head write back address and tail register
when determining progress. This avoids Tx hangs where the software
gets behind, because we are directly checking hardware state when
determining hang state.
Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds check to bail out if device is already down when checking
for Tx hang subtask.
Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parens to make sure the shift and bitwise precedences don't work backwards
for us.
Change-ID: I60c10ef4fad6bc654522b9d8a53da2e270a0f268
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a leak of 'cmd_buf' when copy_from_user() failed
in i40e_dbg_command_write().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement. This will be used by applications to determine
if there are NPAR specific features available.
Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set FLAG_RD for send_driver_version AQ command.
Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setup FCoE netdev device type as "fcoe", so that it shows up in
sysfs as FCoE device.
Change-ID: Ie13a1a332dba4d5802586926104ee01ef20da44f
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BUF flag must be set for indirect AQ command.
Change-ID: I6819718a47baf69d1a91ebaed89f735ed6e86025
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.
By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.
The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.
In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.
Also update the copyright year.
Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add configfs controls to get, set and commit NPAR BW configurations.
We export three controls:
min_bw - Can take a value from 0 to 100 inclusive
max_bw - Can take a value from 1 to 100 inclusive
commit - A write-only control that accepts only a value of 1 and will
cause the BW settings to be permanently committed to NVM so
that they are persistent across power cycles and system
resets
The BW values are relative and are expressed as percentages. For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.
Also update the copyright year.
Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs. These are necessary
precursor functions for that feature.
Also update the copyright year.
Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.
Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy setting from ethtool to the HW specific struct to actually
enable prints. Change print from i40e to i40evf to differentiate
drivers in bare metal scenarios.
Also update the copyright year.
Change-ID: I06fee26247299a08f2e1c70fc811a9ea0931c4dd
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a struct to the VSI struct to keep track of rxnfc
settings done via ethtool. Without this patch, the device can only
list the options available, not the current settings and this is not
clear to the user. Without current settings, the available settings
never changing looks like a bug.
Also update the copyright year.
Change-ID: I087bbfdb33b330496a671630a7586773e3b3e589
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.
Also update the copyright year.
Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under rare circumstances, after a reset, set_rx_mode might get called
while the watchdog is running, which will cause a deadlock on the
critical section lock. To correct this, add a counter and give up trying
to get the lock after fifty tries. Log a message if this happens but
don't take any other action. Because this happens after a reset, all of
the Rx filters are still in place and the device won't lose
connectivity.
We can also get stuck during shutdown, if the PF has stopped communicating
with us, or if a reset is occurring. If we can't get the lock after a reasonable
amount of time, just error out. Something else bad is happening anyway, so
adding this filter is the least of our concern right now.
Change-ID: I159731e2a82a06b389ee31b34ce336548e05baa0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change to the shutdown flow messed up the reset flow. Since
i40evf_down now holds the critical section lock, we cannot call it from
the reset handler, which also holds the lock. To do so causes a deadlock
accompanied by wailing and gnashing of teeth. This is easily triggered
by running an ethtool self-test on the PF device.
Instead, we move the relevant portions of i40evf_down into the reset
handler and bend them to our will. Additionally, we can optimize the
reinit path by not deleting the MAC and VLAN filters and then adding
them back again. Instead, we just set the 'add' flag and let the
watchdog resynchronize the filter list with the PF driver. We also
reword a few messages to make them more consistent with the rest of the
driver.
Change-ID: I03dd92ae736f7719fca3564b12a2cf9b98c6cb18
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When closing the interface, disable NAPI polling before any other
activities. This fixes an occasional panic during close caused by the
driver trying to delete and clean rings at the same time.
Change-ID: Ib4d427b13d310258ea85b248d535da70ecf0c1e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netdev op that allows the operator to turn MAC/VLAN spoof checking on
and off did not include the flag for VLAN spoof checking. This patch
fixes that problem.
Change-ID: Ib4c9e639024a854592d97af22706544881ac3fcb
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.8 and i40evf to 1.2.2
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.
Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't trigger another EMPR when we receive an EMPR event.
This patch handles EMPR event reception with a different state
so that we can do the right thing for NVM.
Change-ID: I9cac70b3658600f016a65beb6fb157e1c1f9adf9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some registers have been removed so take them out and
stop updating and looking at them.
Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use #defined VSI connection type values instead of using magic numbers.
Change-ID: I2f6cf7bf394d391e1c0fe61779e9e4ad8858154a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until the time a more robust versioning scheme is needed/implemented all
established virtual channel opcode values should remain consistent between
updates to the opcode enum.
This patch repositions I40E_VIRTCHNL_OP_CONFIG_RSS to the end of the enum. In
its current position this opcode displaces the initial value of
I40E_VIRTCHNL_OP_EVENT and will cause PF/VF compatibility issues.
Going forward the expectation is either:
a) All future opcode additions will be added as the last element of the
enum. Once VF drivers start making use of the new commands the virtual
channel version will need to be incremented and drivers will need to
implement a simple version check whereby VF drivers can only load on
PFs with a >= version.
b) or, if needed, design and implement a more complicated API
negotiation capability.
In either case PF drivers should always maintain backwards compatibility with
earlier VF driver versions.
Change-ID: Ie245daa09a231b6680ed793d648bdcc76caefe58
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change debugfs command from "clear_stats pf" to "clear_stats port"
to be clearer what the action is. Also, limit the action to the
base PF, not the NPAR partitions.
Change-ID: I22aa39c0962d83a83a985097b1000ed7f8c66f3f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is to refactor the read/write functions to support
future work.
Change-ID: I13150d5e3042f2c617362c0140dc7e6473ebcdee
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed a few cases of when we used msleep() when we should have been
using usleep_range(). Also updated the usage of min/max() to use
min_t/max_t().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Fix the code comments to align with the drivers/net/ commenting style.
Also fix other checkpatch errors such as using tabs where possible and
properly wrap lines to conform to the 80 char limit (unless it is
a string).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
i219 is the next-generation LOM that will be available on systems with the
Sunrise Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Carmen Edwards <carmenx.edwards@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes indentation issue and error found in argument
reported by static analysis. Without this patch, sparse and other
static analysis errors will be found.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all VSIs on a VEB, Loopback mode should be either on or off.
Our configuration requires them to be ON so that VSIs can directly
talk to each other without going out on the wire.
Change-ID: I77b8310bc846329972b13b185949ab1431a46c30
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set different dev_port value 1 for FCoE netdev than the default zero
dev_port value for PF netdev, this helps biosdevname user tool to
differentiate them correctly while both attached to the same PCI
function.
Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure to clear the GPIO blink field, instead of OR'ing against zero
if the field is already '1'.
Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During VF deallocation, we need to lock out the VF reset code. However,
we cannot depend on simply masking the interrupt, as this does not lock
out the service task, which can still call the reset routine. Instead,
leave the interrupt enabled, but add locking around the VF disable and
reset routines.
For the disable code, we wait to get the lock, as the reset code will
take a finite amount of time to run. For the reset code, we just return
if we fail to get the lock. Since we know that the VFs are being
disabled, we don't need to handle the reset.
This fixes a panic when disabling SR-IOV.
Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling 64 VFs and loading the VF driver in the host kernel, we
can easily overrun the PF's admin receive queue. Double the size of this
queue, and increase the work limit to allow the PF to handle more
requests in a single pass through the service task.
Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay a minimum of 10ms after VF reset, to allow the hardware's internal
FIFOs to flush.
Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function i40e_rx_is_fip() that is not used anywhere.
This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the reset and watchdog tasklets into a single task.
The advantage of this is that we can avoid multiple schedules of the reset
task when we have a reset event needed due to either the mailbox going down
or transmit packets being present on a link down.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the logic dealing with link down/up by breaking down the
link detection and up/down events into separate functions - similar to how these
events are handled in other drivers.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to allow for Tx hang checking. The idea is to provide
more robust debug info in the event of a transmit unit hang. Similar to the
logic in ixgbe.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the ordering of the shutdown path so that we attempt to
shutdown the rings more gracefully. Basically the big changes are that we
shutdown the main Rx filter in the case of Rx and we set the carrier_off
state in the case of Tx so that packets stop being delivered from outside
the driver. Then we shut down interrupts and NAPI. Finally we stop the
rings from performing DMA and clean them. This is a bit more graceful than
the previous path.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the setting of vlan_features by enabling all features at once.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants(). The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
My original patch 6a14ee0cfb "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes couple of issues introduced by
commit 2b509c0cd2 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")
- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 provides RSS registers for configuring RSS per VF.
This patch introduces ixgbevf_setup_vfmrqc() which uses the VFRETA,
VFRSSRK and VFMRQC registers to configure RSS on X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables multiple queues and RSS support for the VF.
Maximum of 2 queues are supported due to available vectors.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up prototypes that should have been defined
as static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix two cases where variables are being set but not used.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh<Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, fm10k_update_xc_addr_pf has an issue where it does not
properly drop the upper-most four bits of the VLAN ID due to type
promotion. Resolve the issue not by masking off the bits, but by
throwing an error if the VLAN ID is out-of-bounds.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbevf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use first->protocol instead of skb->protocol to get the proper network
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
igbvf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't update Tx tail descriptor if queue hasn't been stopped
and we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't update Tx tail descriptor if we queue hasn't been stopped and
we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 5ac6f91d changed the igb driver to expose a zero (empty) mac
address to the VF on reset rather than a random one.
However, that behavioral change also requires igbvf driver changes
which can be hard especially when we want to talk to proprietary
guest OSs.
Looking at the code previous to the commit in Linux that made igbvf
work with empty mac addresses (8d56b6d), we can see that on reset
failure the driver will try to generate a new mac address with both
the old and the new code.
Furthermore, ixgbe does send reset failure when it detects an empty
mac address (35055928c).
So I think it's safe to make igb behave the same. With this patch I
can successfully run a Windows 8.1 guest with an empty mac address
and an assigned igbvf device that has no mac address set by the host.
If anyone is aware of a guest driver that chokes on NACK returns of
VF RESET commands, please speak up.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from the hardware team, 100us is too short of a time
to wait for the data path reset to complete and the recommendation is to
increase this timeout to 150us.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k supports up to 184 bytes of inner+outer headers. Add an initial
check to fail encap offload if these are too large.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs). This patch adds support for two of the
possible functions, namely time stamping external events, and periodic
output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 device can produce an interrupt on the full second. This
patch allows using this interrupt to generate an internal PPS event
for adjusting the kernel system time.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The time sync related interrupt registers may be manipulated from
different contexts. This patch protects the registers from being
asynchronously changed by the reset function.
Also, the patch removes a misleading comment. The reset function
is disabling a bunch of functions, not enabling them.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code that handles the time sync interrupt is repeated in three
different places. This patch refactors the identical code blocks into
a single helper function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the Intel 82527EI (driver: e1000e) there is an issue when running
the ptpd2 program, that leads to a kernel oops. The reason is here that
in e1000_xmit_frame() a work queue will be scheduled that has not been
initialized in this case. The work queue "tx_hwstamp_work" will only be
initialized if adapter->flags & FLAG_HAS_HW_TIMESTAMP set. This check
is missing in e1000_xmit_frame().
The following patch adds the missing check.
Signed-off-by: Mathias Koehrer <mathias.koehrer@etas.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after_eq() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.
Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up NVM config read and write data structs.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.
Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.5 and i40evf to 1.0.7.
Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.
Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.
Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup. Also adjust the log strings
a little to look less scary.
Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names
Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase ASQ timeout for some scenarios with multi-function devices
Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several little tweaks to keep FW, SV, and SW in line together
- Remove the unused and deprecated
i40e_aqc_opc_debug_modify_internals
- Add define for iSCSI capability
- Fix queue mask size
- Adjust i40e_aqc_oem_param_change for ease-of-use
Change-ID: I51f250b367912968a7cec61b3a68110d9796e914
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode. This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question. If we're not
in multifunction mode the partition_id will always be 1.
Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were only checking if the link up state had changed,
and if it hadn't exiting the link event routine early. We should
also check if speed has changed, and if it has, stay and finish
processing the link event.
Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in multi-function mode, e.g. Dell's NPAR, only partition 1
of each MAC is allowed to set WoL, speed, and flow control.
Change-ID: I87a9debc7479361c55a71f0120294ea319f23588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function will read PBA Block from Shadow RAM and return it in a string format.
Change-ID: I4ee7059f6e21bd0eba38687da15e772e0b4ab36e
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs. There are some things that
can only be done by the base partition, aka partition_id 1. This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.
Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These mac address already added by FCoE stack above netdev,
therefore adding them here is redundant.
Change-ID: Ia5b59f426f57efd20f8945f7c6cc5d741fbe06e5
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NPAR enabled partitions should warn the user when detected link speed is
less than 10Gpbs.
Change-ID: I7728bb8ce279bf0f4f755d78d7071074a4eb5f69
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some versions of the firmware, the VF admin send queue may become
stalled. In this case, the easiest solution is to just place another
descriptor on the queue; the firmware will then process both requests.
The early init code already accounts for this, but the runtime code does
not. In the watchdog task, check for the stall condition, and if it's
found, send our API version to the PF. When the PF replies, just ignore
the reply.
Change-ID: I380d78185a4f284d649c44d263e648afc9b4d50c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't enable vector 0 in the ISR, just schedule the adminq task and let
it enable the vector. This prevents the task from being called
reentrantly. Make sure that the vector is enabled on all exit paths of
the adminq task, including error exits.
Change-ID: I53f3d14f91ed7a9e90291ea41c681122a5eca5b5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is always a possibility that MSI-X interrupts can get lost. To
keep this problem from stalling the driver, we fire all of our MSI-X
vectors during the watchdog routine. However, we should not fire the
traffic vectors when the interface is closed. In this case, just fire
vector 0, which is used for admin queue events.
As a result, we do not enable the interrupt cause for vector 0. This
can cause the admin queue handler to be called reentrantly, which
causes a scary "critical section violation" message to be logged,
even though no real damage is done.
Change-ID: Ic43a5184708ab2cb9a23fca7dedd808a46717795
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.
Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.
Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.
Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.
If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.
Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.
Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If VF drivers are loaded in the host OS, the call to pci_disable_sriov()
will cause these drivers' remove routines to be called. If the PF driver
has already freed VF resources before this happens, then the VF remove
routine can't properly communicate with the PF driver causing all sorts
of mayhem and error messages and hurt feelings.
To fix this, we move the call to pci_disable_sriov() up to the top of
the function and let it complete before freeing any VF resources.
Change-ID: I397c3997a00f6408e32b7735273911e499600236
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was examining the outer protocol layer to set the inner protocol
layer checksum offload. In the case of TCP over IPV6 over an IPv4 based
VXLAN the inner checksum offloads would be set to look for IPv4/UDP instead
of IPv6/TCP. This code fixes that so that the driver will look at the
proper layer for encapsulation offload settings.
Signed-off-by: Anjali Singhai <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Rx port checksum error counter was incrementing incorrectly with
UDP encapsulated tunneled traffic. This patch fixes the problem so that
the port_rx_csum counter will show accurate statistics.
Signed-off-by: Anjali Singhai <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors. This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor. Does not conflict
with napi because if we are already polling the napi_schedule is
ignored. Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.
Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a FIXME comment that was missed in a commit on 1/2007.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: nick <xerofoify@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although it doesn't explicitly say so, commit 60ffa47875 ("e100:
Fix MDIO/MDIO-X") appears to be intended to revert the earlier commit
648951451e ("e100: fixed e100 MDI/MDI-X issues"). However,
careful examination reveals that the attempted revert actually
_inverted_ the test for eeprom_mdix_enabled. That is bound to program
a few PHYs incorrectly...
https://bugzilla.redhat.com/show_bug.cgi?id=1156417
Signed-off-by: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba7 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline functions are preferred over macros when they can be used
interchangeably.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a little more state context to an NVM update debug message.
Change-ID: I512160259052bcdbe5bdf1adf403ab2bf7984970
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set. This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.
Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only poll on the NVM semaphore if there's time left on a previous
reservation. Also, add a little more info to debug messages.
Change-ID: I2439bf870b95a28b810dcb5cca1c06440463cf8a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The state transitions after an error were not managed well, so
these changes get us back to the INIT state or don't transition
out of the INIT state after most errors.
Change-ID: I90aa0e4e348dc4f58cbcdce9c5d4b7fd35981c6c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit. Also,
rename a variable for clarity and fix a comment.
Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.
Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adminq init is run after the EMPR that is triggered by the
NVM update. The final write command will cause the reset and
will want to wait for the ARQ event that signals the end of the
update, but the reset precludes the event being sent. The state
is probably already at INIT, but we set it so here anyway, and
clear the release_on_done flag as well.
Change-ID: Ie9d724a39e71f988741abc3d51b4cb198c7e0272
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework the debug messages in the NVM update state machine so that we can
turn them on and off dynamically rather than forcing a recompile/reload.
These can now be turned on with something like:
ethtool -s eth1 msglvl 0xf000008f
and off with:
ethtool -s eth1 msglvl 0xf000000f
The high 0xf0000000 gets the driver's attention that we want to change the
internal debug flags, and the 0x80 bit is the NVM debug.
Change-ID: I5efb9039400304b29a0fd6ddea3f47bb362e6661
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish. Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.
Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add more detail to the NVM update error messages so folks
have a better chance at diagnosing issues without having to
resort to heroic measures to reproduce an issue.
Change-ID: I270d1a9c903baceaef0bebcc55d29108ac08b0bd
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once in a great while the NVMUpdate tools and the driver get out
of phase with each other. This gives us a way to reset things
without having to unload the driver.
Change-ID: I353f688236249a666a90ba3e7233e0ed8c1a04e9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-06
This series contains updates to i40e and i40evf.
Shannon provides several patches to cleanup and fix i40e. First removes
an unneeded break statement in i40e_vsi_link_event(). Then removes
some debug messages that really do not give any useful information and
ends up getting printed every service_task loop, which fills the logfile
with noise when AQ tracing is enabled. Updates the aq_cmd arguments to
use %i which is much more forgiving and user friendly than the more
restrictive %x, or %d. Fixes the netdev_stat macro, where the old
xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated.
Getting the pf_id from the function number had an issue when
when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number.
Carolyn adds additional text description for the base pf0 and flow
director generated interrupts, since these interrupts are difficult
to distinguish per port on a multi-function device.
Jacob resolves an issue related to images with multiple PFs per
physical port. We cannot fully support 1588 PTP features, since only
one port should control (i.e. write) the registers at a time. Doing
so can cause interference of functionality.
Anjali provides several updates to i40e, first adds the Virtual Channel
OP event opcode for CONFIG_RSS, so that the Virtual Channel state
machine can properly decipher status change events. Then updates the
driver to add (and use) i40e_is_vf macro for future expansion when new
VF MAC types get added. Adds new update VSI flow to accommodate a
firmware dix with VSI loopback mode. All VSIs on a VEB should either
have loopback enabled or disabled, a mixed mode is not supported for a
VEB. Since our driver supports multiple VSIs per PF that need to talk to
each other make sure to enable Loopback for the PF and FDIR VSI as well.
Mitch provides a couple of i40e and i40evf patches. First updates
i40evf init code more adept at handling when multiple VFs attempt
to initialize simultaneously.
Joe Perches provides a i40e patch which resolves a compile warning
about about frame size being larger than 2048 bytes by reducing the
stack use by using kmemdup and not using a very large struct on the
stack.
v2:
- Dropped patch 13 & 14 while Mitch reworks the patches based on
feedback from Ben Hutchings, probably the tryptophan in the turkey
is to blame for the delay...
- Added Joe Perches patch which resolves a compile warning about frame
size
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce stack use by using kmemdup and not using a very
large struct on stack.
In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Getting the pf_id from the function number was a good place to start,
but when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number. This works in NPAR mode as well.
Change-ID: I65e3dd6c97594890c2bad566b83cc670b1dae534
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ needs to have at least as many entries as VFs, or the VFs will
get errors from the FW when they send messages to the PF. Since we don't
know how many VFs we'll end up with, just set up 128 descriptors.
Change-ID: I04ae3d1c7faf09110eb782214e9c05aeb62a6c59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.
Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.
Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.
Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase reset delay to ensure all internal caches are properly flushed
in worst case scenario.
Change-ID: I6f059a9e024fbf9ef1debd32497eed21369957fc
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated. Since we're
using rtnl_link_stats64 in other parts of the driver, we should use it
here as well. We've just been lucky that the field definitions are the
same sizes.
Change-ID: I19fc71619905700235dcdf0d3c8153aec81d36de
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.
It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.
This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).
The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.
Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds additional text description for base pf0 and flow director
generated interrupts. Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.
Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments. This makes the user interface much more forgiving and user
friendly.
Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.
Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves couple of issues in ixgbevf_probe/remove():
1. Fix a case where adapter->state is tested after free_netdev() this is
same as the patch for ixgbe from Daniel Borkmann <dborkman@redhat.com>:
commit b5b2ffc057 ("ixgbe: fix use after free adapter->state test in ixgbe_remove/ixgbe_probe")
2. Move pci_set_drvdata() after all the error checks in ixgbevf_probe() and
then add a check in ixgbevf_probe() to avoid running the cleanup functions
twice in cases where probe failed.
CC: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds initial support for VFs on a new mac - X550.
The patch adds the basic structures and device IDs for the X550 VFs
that would allow the driver to load and pass traffic.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.
This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
