If a CRTC comprises of 2 LMs, it is mandatory to enable border out
and assign it to the base stage.
We had to enable border out also when the base plane wasn't fullscreen.
Club these checks and put them in a separate function called
get_start_stage() that returns the starting stage for assigning planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that our mdp5_planes can consist of 2 hwpipes, update the
blend_setup() code to stage the right hwpipe to the left and
right LMs
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to enable Source Split in HW, we need to add/modify
a few LM register configurations:
- Configure the LM width to be half the mode width, so that
each LM manages one half of the scanout.
- Tell the 'right' LM that it is configured to be the 'right'
LM in source split mode.
- Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is
configured, do a read-update-store for the register instead of
directly writing a value to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we have a right hwpipe in mdp5_plane_state, configure it
mdp5_plane_mode_set(). The only parameters that vary between the
left and right hwpipes are the src_w, src_img_w, src_x and crtc_x
as we just even chop the fb into left and right halves.
Add a mdp5_plane_right_pipe() which will be used by the crtc code
to set up LM stages.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the drm_plane has a source width that's greater than the max width
supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe'
to it in mdp5_plane_atomic_check().
TODO: There are a few scenarios where the hwpipe assignments aren't
recommended by HW. For example, an assignment which results in a
drm_plane to of two different types of hwpipes (say RGB0 on left
and DMA1 on right) is not recommended.
Also, hwpipes have a priority mapping, where the higher priority pipe
needs to be staged on left LM, and the lower priority needs to be
staged on the right LM. For example, the priority order for VIG pipes
in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0
on left and VIG1 on right is a correct configuration, but VIG1 on left
and VIG0 on right isn't. These scenarios are ignored for now for the
sake of simplicity.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter
func takes in only the hwpipe and the parameters that need to be
programmed into the hwpipe registers. All the code that calculates these
parameters is left as is in mdp5_plane_mode_set.
In the future, when we let drm_plane be comprised of 2 hwpipes, this func
allow us to configure each pipe without adding redundant code.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.
With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.
A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.
For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.
The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.
This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some of the newer MDP5 versions support Source Split of SSPPs. It is a
feature that allows us to route the output of a hwpipe to 2 Layer
Mixers. This is required to achieve the following use cases:
- Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single
DSI interface doesn't have the bandwidth to drive the required pixel
clock. We use 2 DSI interfaces to drive the left and right halves
of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look
like:
LM0 -- DSPP0 -- INTF1 -- DSI1
/
hwpipe--
\
LM1 -- DSPP1 -- INTF2 -- DSI2
A single hwpipe is used to scan out the left and right halves to DSI1
and DSI2 respectively. In order to do this, we need to configure the
2 Layer Mixers in Source Split mode.
- HDMI 4K: In order to support resolutions with width higher than the
max width supported by a hwpipe, we club 2 hwpipes together:
hwpipe1 --- LM0 -- DSPP0
- - \
- -- 3D Mux -- INTF0 -- HDMI
- - /
hwpipe2 --- LM1 -- DSPP1
hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on
the 'right' Layer Mixer. An additional block called the '3D Mux' is
used to merge the output of the 2 DSPPs to a single interface.
In this use case, it is possible that a 4K surface is downscaled and
placed completely within one of the halves. In order to support such
scenarios (and keep the programming simple), Layer Mixers with Source
Split can be assigned 2 hw pipes per stage. While scanning out, the HW
takes care of fetching the pixels fom the correct pipe.
Add a MDP cap to tell whether the HW supports source split or not.
Add a MDP LM cap that tells whether a LM instance can operate in
source split mode (and generate the 'left' part of the display
output).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.
We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the last few commits, we've been adding params to mdp5_crtc_state, and
assigning them in the atomic_check() funcs. Now it's time to actually
start using them.
Remove the duplicated params from the mdp5_crtc struct, and start using
them in the mdp5_crtc code. The majority of the references to these params
is in code that executes after the atomic swap has occurred, so it's okay
to use crtc->state in them. There are a couple of legacy LM cursor ops that
may not use the updated state, but (I think) it's okay to live with that.
Now that we dynamically allocate a mixer to the CRTC, we can also remove
the static assignment to it in mdp5_crtc_init, and also drop the code that
skipped init-ing WB bound mixers (those will now be rejected by
mdp5_mixer_assign()).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.
Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).
These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.
With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.
We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.
Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the stuff needed to allow dynamically assigning a mixer to a CRTC.
Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.
The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.
The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.
The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.
Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).
The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.
Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.
Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.
Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.
This avoids the need to retrieve PP ID using macros
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.
Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.
For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.
This is very similar to how hwpipes were previously abstracted away
from drm planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.
Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.
Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Zero sized buffer objects tend to make various bits of the GEM
infrastructure complain:
WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0
Modules linked in:
CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G W 4.9.0-rc4-00906-g693af44 #213
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
task: ffff8000d7353400 task.stack: ffff8000d7720000
PC is at drm_mm_insert_node_generic+0x258/0x2f0
LR is at drm_vma_offset_add+0x4c/0x70
Zero sized buffers serve no appreciable value to the user so disallow
them at create time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Output the upper 32 bits of a 64 bit iova in the RD_CMDSTREAM_ADDR
section while maintaining backwards compatibility for tools that
only understand 32 bit iovas.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The interrupt status was being cleared before processing the handlers.
a5xx_rbbm_err_irq() was checking the interrupt status again, which would
likely turn out bad because the interrupt status would be 0 (or at least
different). Pass the original status to the function instead.
Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt
will keep firing until the error source is cleared. Skip the clear to
avoid a storm until the error is cleared in a5xx_rbbm_err_irq().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
priv->num_aspaces is increased and then checked to see if it still fits
in the priv->aspace array. If it doesn't, we warn and exit but
priv->num_aspaces remains incremented.
Don't incremement the count until we know that it fits in the array.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The core takes care of handling the send_event vs. close() issues, we
can remove that driver code.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Probably a symptom of needing finer grained locking, but if we wait on
the incoming fence-fd (which could come from a different context) while
holding struct_mutex, that blocks retire_worker so gpu fences cannot get
signalled.
This causes a problem if userspace manages to get more than a frame
ahead, leaving the atomic-commit worker blocked waiting on fences that
cannot be signaled because submit is blocked waiting for a fence
signalled from vblank (after the atomic commit which is blocked).
If we start having multiple fence ctxs for the gpu, submit_fence_sync()
would probably need to move outside of struct_mutex as well.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Significantly simplifies things. Also iommu_unmap() can unmap an entire
iova range.
(If backporting to downstream kernel you might need to revert this. Or
at least double check older iommu implementation.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Each of the per-generation callbacks was doing this. Lets just simplify
and move it into toplevel show() fxn.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This reverts
commit b8dfa821c2
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Apr 7 12:17:12 2017 +0100
drm: Don't allow interruptions when opening debugfs/crc
It reportedly breaks things, so let's revert now and try again later.
Fixes: b8dfa821c2 ("drm: Don't allow interruptions when opening debugfs/crc")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
V2: remove **array method, directly fence_put after fence wait.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <chrstian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The offset must be 64bit and add back the accidential dropped line.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By default, the value is set by individual gmc.
if a specific value is input, it overrides the global value for all
v2: create helper funcs
v3: update gmc9 APU's num_level athough it may be updated in the future.
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I thought I've fixed this, but maybe not. Anyway, clearly broken, and
easy fix.
Cc: Tony Lindgren <tony@atomide.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Fixes: b95ff0319a ("drm: Remove drm_modeset_(un)lock_crtc")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407164817.28272-1-daniel.vetter@ffwll.ch
I've broken this by removing the backoff handling from the
set_config2atomic helper in
commit 38b6441e4e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 22 22:50:58 2017 +0100
drm/atomic-helper: Remove the backoff hack from set_config
Fixing this properly would mean we get to wire the acquire_ctx all the
way through vmwgfx fbdev code, and doing the same was tricky for the
shared fbdev layer. Probably much better to look into refactoring the
entire code to use the helpers, but since that's not a viable
long-term solution fix the issue by open-coding a vmwgfx version of
set_config, that does the legacy backoff dance internally.
Note: Just compile-tested. The idea is to take
drm_mode_set_config_internal(), remove the "is this a legacy driver"
check, and whack the drm_atomic_legacy_backoff trickery at the end.
Since drm_atomic_legacy_backoff is for atomic commits only we need to
open-code it.
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170406200256.26040-1-daniel.vetter@ffwll.ch
Current drm bind/unbind sequence would cause some memory issues.
For example we should not cleanup iommu before cleanup mode config.
Reorder bind/unbind sequence, follow exynos drm.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
[seanpaul fixed spelling typo in commit subject]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-11-git-send-email-jeffy.chen@rock-chips.com
We're trying to access vop registers here, so need to make sure
the pm domain is on.
Normally it should be enabled by the bootloader, but there's no
guarantee of it. And if we wanna do unbind/bind, it would also
cause the device to hang.
And this patch also does these:
1/ move vop_initial to the end of vop_bind for eaiser error handling.
2/ correct the err_put_pm_runtime of vop_enable.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-8-git-send-email-jeffy.chen@rock-chips.com
After snd_soc_unregister_codec, the dai link would remain bound to
the invalid codec. That would cause crashes after unbind dp driver.
Let's unregister audio codec when removing dp driver to prevent that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-7-git-send-email-jeffy.chen@rock-chips.com
Normally we do this in drm_mode_config_cleanup. But:
1/ analogix dp's connector is allocated in bind, and freed after unbind.
So we need to destroy it in unbind to avoid further access.
2/ the drm bridge is attached in bind, and detached in encoder cleanup.
So we need to destroy encoder in unbind.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-5-git-send-email-jeffy.chen@rock-chips.com
At dot clocks > approx. 250 Mhz, some of these calcs will overflow and
cause miscalculation of latency watermarks, and for some overflows also
divide-by-zero driver crash ("divide error: 0000 [#1] PREEMPT SMP" in
"dce_v10_0_latency_watermark+0x12d/0x190").
This zero-divide happened, e.g., on AMD Tonga Pro under DCE-10,
on a Displayport panel when trying to set a video mode of 2560x1440
at 165 Hz vrefresh with a dot clock of 635.540 Mhz.
Refine calculations to avoid the overflows.
Tested for DCE-10 with R9 380 Tonga + ASUS ROG PG279 panel.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoid big roundoff errors in scanline/hactive durations for
high pixel clocks, especially for >= 500 Mhz, and thereby
program more accurate display fifo watermarks.
Implemented here for DCE 6,8,10,11.
Successfully tested on DCE 10 with AMD R9 380 Tonga.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The RV3xx settings were getting applied to all older asics
rather than just RV3xx.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BOs shared via dma-buf, either imported or exported, cannot sensibly be migrated to VRAM
without breaking the dma-buf sharing. Refuse userspace requests to migrate to VRAM,
ensure such BOs are not migrated during command submission, and refuse to pin them
to VRAM.
v2: Don't pin BOs in GTT. Instead, refuse to migrate BOs to VRAM.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Migration to VRAM will break the sharing, resulting in rendering on the exporting GPU never becoming
visible on the importing GPU.
v2: Don't pin BOs to GTT. Instead, refuse to migrate them out of GTT.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Any use of the framebuffer will migrate it to VRAM, which is not sensible for
an imported dma-buf.
v2: Use DRM_DEBUG_KMS to prevent userspace accidentally spamming dmesg.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
CC: amd-gfx@lists.freedesktop.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Any use of the framebuffer will migrate it to VRAM, which is not sensible for
an imported dma-buf.
v2: Use DRM_DEBUG_KMS to prevent userspace accidentally spamming dmesg.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
CC: amd-gfx@lists.freedesktop.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch add support for the Mediatek MT2701 DISP subsystem.
There is only one OVL engine in MT2701.
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
This patch update enable/disable flow of DSI module.
Original flow works on there is a bridge chip: DSI -> bridge -> panel.
In this case: DSI -> panel, the DSI sub driver flow should be updated.
We need to initialize DSI first so that we can send commands to panel.
Signed-off-by: shaoming chen <shaoming.chen@mediatek.com>
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
This patch will update dsi clock control method.
1. dsi non-continue clock mode will enhance antistatic effect for panel
2. EOT packet control will judge whether dsi send end of packet or not
by customize
Signed-off-by: shaoming chen <shaoming.chen@mediatek.com>
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
cleaning up unused define and refine function name and variable
Signed-off-by: shaoming chen <shaoming.chen@mediatek.com>
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
We need to acquire mutex before using the resources,
and need to release it after finished.
So we don't need to write registers in the blanking period.
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
There are some hardware settings changed, between MT8173 & MT2701:
DISP_OVL address offset changed, color format definition changed.
DISP_RDMA fifo size changed.
DISP_COLOR offset changed.
MIPI_TX pll setting changed.
And add prefix for mtk_ddp_main & mtk_ddp_ext & mutex_mod.
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
define helpers for converting from 'mtk_ddp_comp' to 'mtk_disp_ovl'
define helpers for converting from 'mtk_ddp_comp' to 'mtk_disp_rdma'
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
The plat_data->input_bus_format and plat_data->input_bus_encoding
are unsigned long and are always >=0, but the value 0 was still
considered as RGB888 for input_bus_format and default color space
for input_bus_encoding in the reworked code.
This patch changes the if statement check for a non-zero value to
either use the default input bus_format and/or bus_encoding for a zero
value and the provided bus_format and/or bus_encoding for a
non zero value.
Thanks to Dan Carpenter for his bug report at [1].
Tested on Amlogic P230 (with CSC enabled for YUV444 to RGB) and Rockchip
RK3288 ACT8846 EVB Board (no CSC involved, direct RGB passthrough).
[1] http://lkml.kernel.org/r/20170406052120.GA26578@mwanda
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[narmstrong@baylibre.com: reworded commit message and added Fixes tag]
Link: http://patchwork.freedesktop.org/patch/msgid/1491471244-24989-1-git-send-email-narmstrong@baylibre.com
This adds support for the Winstar Display Co. WF35LTIACD 3.5" QVGA TFT
LCD panel, which can be supported by the simple panel driver.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sitronix ST7789v controller is used to drive 240x320 LCD panels through
various interfaces, including SPI and RGB/Parallel.
The current driver is configuring it for the latter. Support for tinyDRM
can always be added later.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
driver. This panel has 1440x2560 resolution in 5.7-inch physical
panel in the TM2 device.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add simple-panel support for the Ampire AM-480272H3TMQW-T01H, which is a
4.3" WQVGA panel.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.
In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Many drivers have a common pattern of searching the OF graph for either an
attached panel or bridge and then finding the DRM struct for the panel
or bridge. Also, most drivers need to handle deferred probing when the
DRM device is not yet instantiated. Create a common function,
drm_of_find_panel_or_bridge, to find the connected node and the
associated DRM panel or bridge device.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
[seanpaul dropped extern from drm_of.h]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The atomic_check function is useful for implementing properties, but
it can be used for other connector modeset related checks as well.
Similar to plane check functions, on a modeset atomic_check() is always
called.
Changes since v1:
- Make sure atomic_check() is called on any modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-5-git-send-email-maarten.lankhorst@linux.intel.com
Now that handle_conflicting_encoders no longer touches active state,
so there's no need to do the check quite that late any more.
Doing it with all the other checks makes it a lot more clear what the
below block tries to accomplish, and this feels like a better place to
put the check.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-4-git-send-email-maarten.lankhorst@linux.intel.com
Now that handle_conflicting_encoders cannot disable crtc's any more
it makes sense to set all the changed flags in 1 place.
This makes the code slightly less magical.
The (now removed) comment is out of date. The only reason the
active_changed was set late was because handle_conflicting_encoders
could disable connectors. This is no longer the case,
and we can put everything in 1 place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-3-git-send-email-maarten.lankhorst@linux.intel.com
Currently we use a flag to change behavior in atomic commit
whether a conflicting encoder should be enabled or disabled.
This is used for the legacy set_config helper, which disables
connectors that have a conflicting encoder but not part of the
active crtc list.
There's no need for this to be handled in atomic commit, it
could be done in the set_config helper instead. This will
let the atomic check function reject any conflicting encoders,
while set_config can disable conflicting crtc's. This makes it
possible to recalculate the changed flags in 1 loop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-2-git-send-email-maarten.lankhorst@linux.intel.com
Legacy drivers insist that we really take all the locks in this path,
and the harm in doing so is minimal.
v2: Like git add, it exists :(
Fixes: 2ceb585a95 ("drm: Add explicit acquire ctx handling around ->set_config")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: Alex Deucher <alexdeucher@gmail.com>
Reported-by: Alex Deucher <alexdeucher@gmail.com>
Acked-and-tested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170406190654.6733-1-daniel.vetter@ffwll.ch
A few more things for 4.12:
- ttm and amdgpu support for non-contiguous vram CPU mappings
- lots of bug fixes and cleanups for vega10
- misc bug fixes and code cleanups
[airlied: fix do_div error on 32-bit arm, not sure it's 100% correct]
* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (58 commits)
drm/amdgpu: use uintptr_t instead of unsigned long to store pointer
drm/amdgpu: Avoid using signed integer to store pointer value
drm/amdgpu:invoke new implemented AI MB func
drm/amdgpu/vega10:timeout set to equal with VI
drm/amdgpu:implement the reset MB func for vega10
drm/amdgpu:fix typo for mxgpu_ai
drm/amdgpu:no need to involv HDP in KIQ
drm/amdgpu:add PSP block only load_type=PSP (v2)
drm/amdgpu/smu9: update to latest driver interface
drm/amd/amdgpu: cleanup gfx_v9_0_gpu_init()
drm/amd/amdgpu: cleanup gfx_v9_0_rlc_reset()
drm/amd/amdgpu: cleanup gfx_v9_0_rlc_start()
drm/amd/amdgpu: simplify gfx_v9_0_cp_gfx_enable()
drm/amd/amdgpu: cleanup gfx_v9_0_kiq_init_register()
drm/amd/amdgpu: Drop gfx_v9_0_print_status()
drm/amd/amdgpu: cleanup gfx_v9_0_set_gfx_eop_interrupt_state()
drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_reg_fault_state()
drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_inst_fault_state()
drm/amd/amdgpu: cleanup gfx_v9_0_init_queue()
drm/amdgpu: Move function amdgpu_has_atpx near other similar functions
...
Highlights:
- Cooling device support from Russell, to allow GPU throttling on system
thermal overload.
- Explicit fencing support from Philipp, implemented in a similar way to
drm/msm.
* 'etnaviv/next' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: submit support for out-fences
drm/etnaviv: return GPU fence through the submit structure
drm/etnaviv: submit support for in-fences
drm/etnaviv: add etnaviv cooling device
drm/etnaviv: switch to postclose
drm/etnaviv: add lockdep assert to fence allocation
- The PRE/PRG drivers added an unwanted DRM dependency to the ipu-v3 driver.
Remove the dependency by conditionally disabling PRE/PRG support depending
on CONFIG_DRM.
- Merge the imx-ipuv3-crtc module into the imxdrm module. There is no reason
anymore for a separation between core drm driver and crtc/plane drivers,
especially since commit eb8c88808c ("drm/imx: add deferred plane
disabling"), which added a dependency on imx-ipuv3-crtc to the imxdrm
module.
-----BEGIN PGP SIGNATURE-----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=3ZIW
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2017-04-04' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm module/dependency changes
- The PRE/PRG drivers added an unwanted DRM dependency to the ipu-v3 driver.
Remove the dependency by conditionally disabling PRE/PRG support depending
on CONFIG_DRM.
- Merge the imx-ipuv3-crtc module into the imxdrm module. There is no reason
anymore for a separation between core drm driver and crtc/plane drivers,
especially since commit eb8c88808c ("drm/imx: add deferred plane
disabling"), which added a dependency on imx-ipuv3-crtc to the imxdrm
module.
* tag 'imx-drm-next-2017-04-04' of git://git.pengutronix.de/git/pza/linux:
drm/imx: merge imx-drm-core and ipuv3-crtc in one module
gpu: ipu-v3: don't depend on DRM being enabled
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement the sr-iov mailbox for soc15 asics.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
they are lack in the bringup stage, we need them for GPU reset
feature.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1,KIQ won't touch VRAM so no need to involv HDP flush/invalidate at all.
2,According to CP hw designer KIQ better not use any PM4 package lead to wait behave.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SRIOV currently only can load ucode directly, and PSP
block is not supported by VF temporarily.
will remove this restrict and use PSP load all ucode
even for SRIOV later
v2: squash in check against module parameter
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD macro
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's not used in gfx 6/7/8 so drop it from gfx 9 as well.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD15 macro.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce WREG32_FIELD15 macro for SOC15 architectures.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need an array of pointers to IRQ sources, not an array of sources.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Had the wrong sense in the loop
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two hubs are just instances of the same hardware,
so the register bits are identical.
v2: keep the function pointer
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set reasonable defaults per family.
v2: set both of them in gmc
v3: move vm size and block size in vm manager
v4: squash in warning fix from Alex Xie
v5: squash in min() warning fix
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up a toggle with ?:.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Swap read/write pattern for WREG32_FIELD()
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Swap read/write pattern for WREG32_FIELD()
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new WREG32_FIELD_OFFSET() to clean up code.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two hubs are just instances of the same hardware,
so the register bits are identical.
v2: only remove get_vm_protection_bits for now
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This avoids merging them together on page fault.
v2: squash in 64-bit division fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we use virtio-vga with a big-endian guest,
the mouse pointer disappears.
To fix that, on big-endian use DRM_FORMAT_BGRA8888
instead of DRM_FORMAT_ARGB8888.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170405080915.823-1-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It's too chatty to have three places to tell us which one
is next vgpu for schedule. My log file was bloated to eat
all disk space..
Cc: Ping Gao <ping.a.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
There was supposed to be a break before the next case statement.
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170406052132.GA26605@mwanda
The goal is to push all the kms locking down into these separate
_atomic and _legacy functions, so that we can correctly pass the
acquire ctx into all atomic drivers. Instead of playing games with
hidden ctx in mode_config.acquire_ctx. All the fbdev state will be
protected by a new fbdev private lock that Thierry is working on.
This here is just prep by creating a clean split between atomic and
legacy paths, which also simplifies the control flow a bit.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-16-daniel.vetter@ffwll.ch
I got confused every time I audited what that lock_all is doing in
there until realizing it's for legacy kms only. Make that a notch more
obvious by having 2 entirely different paths.
While at it also move the atomic version of this into
drm_framebuffer.c, there's no reason it needs to be in drm_atomic.c.
That way it becomes a simple static function.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-15-daniel.vetter@ffwll.ch
Another one knocked down.
With this we can also remove the temporary hack in the gamma_set
ioctl.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-14-daniel.vetter@ffwll.ch
Atomic helpers really want this instead of the hacked-up legacy
backoff trick, which unfortunately prevents drivers from using their
own private drm_modeset_locks.
Aside: There's a few atomic drivers (nv50, vc4, soon vmwgfx) which
don't yet use the new atomic color mgmt/gamma table stuff. Would be
nice if they could switch over and just hook up
drm_atomic_helper_legacy_gamma_set() instead.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-13-daniel.vetter@ffwll.ch
Just the groundwork to prepare for adding the acquire cxt parameter to
the ->gamma_set hook. Again we need a temporary hack to fill out
mode_config.acquire_ctx until the atomic helpers are switched over.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-12-daniel.vetter@ffwll.ch
It just doesn't work. It probably stopped working way, way before that
(e.g. i915 grabbed random mutexes all over in modeset code at least
since gen6), but with atomic and all the ww_mutex stuff it's indeed
hopeless.
Remove ->mode_set_base_atomic from the 2 atomic drivers (i915 and
nouveau) that still had one (both had dummy implementations already
anyway), and shunt atomic drivers in the helpers debug_enter/leave
functions.
I'll leave the code in for radeon and amdgpu, but I think as soon as
amdgpu is atomic we should think about just ripping it out. Only
having it around for radeon and pre-nv50 is rather pointless. This
would also allow us to nuke all that code from fbdev.
Funny part is that _all_ kms drivers set this hook, despite that no
one else provides the required ->mode_set_base_atomic implementation.
The reason I'm jumping on this is that I want to wire up a full
acquire ctx for the benefit of atomic drivers, everywhere. And the
debug_enter/leave implementations call ->gamma_set. And there's just
no way ever we can create an acquire_ctx in the nmi context of kgdb.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-11-daniel.vetter@ffwll.ch
GP10B's power is managed by generic PM domains, so it does not require a
VDD regulator. Add this option into the chip function structure.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GR is similar to GP100, with a few unavailable registers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP10B requires a specific initialization sequence due to the absence of
devinit.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP10B's MC is compatible with GP100's, but engines need to be explicitly
put out of ELPG during init.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP10B's FB is largely compatible with the GP100 implementation.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP10B's FIFO is similar to GP100's, but only allows 512 channels.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The GP10B firmware is very close to GM20B's. The only difference is that
it supports booting multiple falcons. In order to avoid having too much
functions and structures shared, implement its support in the same
source file as GM20B firmware.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP10B's secboot is largely similar to GM20B's. Only differences are MC
base address and the fact that GPCCS is also securely managed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allow the MC base address to be specified as an argument for the WPR
region reading function. GP10B uses a different address layout as GM20B,
so this is necessary. Also export the function to be used by GP10B.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The LS firmware post-run hook is the right place to start said LS
firmware. Moving it here also allows to remove special handling in the
ACR code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A LS post-run hook can meet an error meaning the failure of secure boot.
Make sure this can be reported.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Having access to the secboot instance loading a LS firmware can be
useful to LS firmware handlers. At least more useful than just having an
out-of-context subdev pointer.
GP10B's firmware will also need to know the WPR address, which can be
obtained from the secboot instance.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Change the secboot and msgqueue interfaces to take a mask of falcons to
reset instead of a single falcon. The GP10B firmware interface requires
FECS and GPCCS to be booted in a single firmware command.
For firmwares that only support single falcon boot, it is trivial to
loop over the mask and boot each falcons individually.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The gk20a implementation of instance memory uses vmap()/vunmap() to map
memory regions into the kernel's virtual address space. These functions
may sleep, so protecting them by a spin lock is not safe. This triggers
a warning if the DEBUG_ATOMIC_SLEEP Kconfig option is enabled. Fix this
by using a mutex instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Forked from GP106 implementation.
Split out from commit enabling secboot/gr support so that it can be
added to earlier kernels.
Cc: stable@vger.kernel.org [4.10+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When the atomic support was added to nouveau, the DRM core did not do this.
However, later in the same merge window, a commit (drm/fence: add in-fences
support) was merged that added it, leading to use-after-frees of the fence
object.
Cc: stable@vger.kernel.org [4.10+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The NV4A (aka NV44A) is an oddity in the family. It only comes in AGP
and PCI varieties, rather than a core PCIE chip with a bridge for
AGP/PCI as necessary. As a result, it appears that the MMU is also
non-functional. For AGP cards, the vast majority of the NV4A lineup,
this worked out since we force AGP cards to use the nv04 mmu. However
for PCI variants, this did not work.
Switching to the NV04 MMU makes it work like a charm. Thanks to mwk for
the suggestion. This should be a no-op for NV4A AGP boards, as they were
using it already.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Forked from GP106 implementation.
Split out from commit enabling secboot/gr support so that it can be
added to earlier kernels.
Cc: stable@vger.kernel.org [4.10+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When the atomic support was added to nouveau, the DRM core did not do this.
However, later in the same merge window, a commit (drm/fence: add in-fences
support) was merged that added it, leading to use-after-frees of the fence
object.
Cc: stable@vger.kernel.org [4.10+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The NV4A (aka NV44A) is an oddity in the family. It only comes in AGP
and PCI varieties, rather than a core PCIE chip with a bridge for
AGP/PCI as necessary. As a result, it appears that the MMU is also
non-functional. For AGP cards, the vast majority of the NV4A lineup,
this worked out since we force AGP cards to use the nv04 mmu. However
for PCI variants, this did not work.
Switching to the NV04 MMU makes it work like a charm. Thanks to mwk for
the suggestion. This should be a no-op for NV4A AGP boards, as they were
using it already.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix wrong initial csb read pointer value. This fixes the random
engine timeout issue in guest when guest boots up.
Fixes: 8453d674ae ("drm/i915/gvt: vGPU execlist virtualization")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Min He <min.he@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We do set DRIVER_ATOMIC now.
Note that the comment is outdated, the property paths switched over to
checking drm_drv_uses_atomic_modeset() a while ago. Which means this
can't even break if we revert DRIVER_ATOMIC again.
v2: Add note that this is even safer (Maarten).
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-9-daniel.vetter@ffwll.ch
We don't call into drivers at all here, this is enough. Also, we can
reduce the critical section a bit to simplify the code.
crtc->gamma_size is set up once at driver load and then invariant, so
also doesn't need any protection.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-8-daniel.vetter@ffwll.ch
Properties, i.e. the struct drm_property specifying the type and value
range of a property, not the instantiation on a given object, are
invariant over the lifetime of a driver.
Hence no locking at all is needed, we can just remove it.
While at it give the function some love and simplify it, to get it
under the 80 char limit:
- Straighten the loops to reduce the nesting.
- use u64_to_user_ptr casting helper
- use put_user for fixed u64 copies.
Note there's a small behavioural change in that we now copy parts of
the values to userspace if the arrays are a bit too small. Since
userspace will immediately retry anyway, this doesn't matter.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-7-daniel.vetter@ffwll.ch
If we push the locks down we don't have to take them all at the same
time.
Aside: Making dump_info fully safe should be fairly simple, if we
protect the ->state pointers with rcu. Simply putting a
synchronize_rcu() into the drm_atomic_state free function should be
all that's roughly needed. Well except we shouldn't block in there, so
better to put that into a work_struct. But I've not set out to fix
that little issue.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-6-daniel.vetter@ffwll.ch
With all the callers of drm_modeset_lock_crtc gone, and all the places
it was formerly used properly wiring the acquire ctx through, we can
remove this.
The only hidden context magic we still have is now the global one.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-4-daniel.vetter@ffwll.ch
The last user, the cursor ioctl, can just open-code this too. We
simply have to move the acquire ctx dance from the universal function
up into the top-level ioctl handler.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-3-daniel.vetter@ffwll.ch
This is only for legacy paths that need to grab the crtc/plane lock
combo. If you want to lock a crtc, just use drm_modeset_lock().
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-2-daniel.vetter@ffwll.ch
Implement AMDGPU_GEM_CREATE_VRAM_CONTIGUOUS using TTM_PL_FLAG_CONTIGUOUS
instead of a placement limit. That allows us to better handle CPU
accessible placements.
v2: prevent virtual BO start address from overflowing
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should probably rename amdgpu_gart_funcs sooner or later.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove some of the extra checks where they don't hurt us.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Abort early if there is nothing todo and correctly indent the "if"s.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The name is a bit confusing and the extra "? true : false" is superflous.
Additional to that remove setting the reset counter directly after checking it.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not used any more.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Try to clean up amdgpu.h.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Match our defines with what the hw uses.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We will probably never see this combination.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows drivers to specify if they need a contiguous allocation or not.
v2: use space instead of tab
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows the driver to handle io_mem mappings on their own.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to implement the same logic twice. Also check if the busy placements
are identical to the already scanned placements before checking them.
v2: improve check even more as suggested by Michel.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
vega10 is the only soc15 asic at the moment so these
warnings are invalid, but add a default case to silence
the warnings.
Fixes: 220ab9bd1c: "drm/amdgpu: soc15 enable (v3)"
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With the atomic API, it is possible that a single commit affects
multiple crtcs. If the user requests an event with that commit, one
event will be sent for each CRTC, but it is not possible to distinguish
which crtc an event is for in user space. To solve this, the reserved
field in struct drm_vblank_event is repurposed to include the crtc_id
which the event is for.
The DRM_CAP_CRTC_IN_VBLANK_EVENT is added to allow userspace to query if
the crtc field will be set properly.
[daniels: Rebased, using Maarten's forward-port.]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170404165221.28240-2-daniels@collabora.com
Also unify/merge with the existing stuff.
I was a bit torn where to put this, but in the end I decided to put
all the ioctl/sysfs/debugfs stuff into drm-uapi.rst. That means we
have a bit a split with the other uapi related stuff used internally,
like drm_file.[hc], but I think overall this makes more sense.
If it's too confusing we can always add more cross-links to make it
more discoverable. But the auto-sprinkling of links kernel-doc already
does seems sufficient.
Also for prettier docs and more cross-links, switch the internal
defines over to an enum, as usual.
v2: Update kerneldoc fro drm_compat_ioctl too (caught by 0day), plus a
bit more drive-by polish.
v3: Fix typo, spotted by xerpi on irc (Sergi).
v4: Add missing space in comment (Neil).
Cc: Sergi Granell <xerpi.g.12@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170404095304.17599-4-daniel.vetter@ffwll.ch
- remove docs for internal func, doesn't add value
- add short overview snippet instead explaining that drivers don't
have to bother themselves with reg/unreg concerns
- drop the ttm comment about drmP.h, drmP.h is disappearing ...
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170404095304.17599-2-daniel.vetter@ffwll.ch
On KB, KV, CZ we should read the vram width from integrated system
table, if we can. The NOOFCHAN in MC_SHARED_CHMAP is not accurate.
With this change we can enable two 4k displays on CZ again. This use
case was broken sometime in January when we started looking at
vram_width for bandwidth calculations instead of hardcoding this value.
v2:
Return 0 if integrated system info table is not available.
Tested-by: Roman Li <roman.li@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
break it out from the check parameters function.
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We accidentally dereference "cb" if the kmalloc() fails.
Fixes: 451bc8eb8f ("drm/amdgpu: fix PRT teardown on VM fini v3")
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should return unlock on the error path in pp_dpm_dispatch_tasks()
and there is a double lock bug in pp_dpm_set_sclk_od().
Fixes: 2a5071056e ("drm/amd/powerplay: add global PowerPlay mutex.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This switch statement is missing breaks.
v2: agd: break in default case as well
Fixes: 2a5071056e ("drm/amd/powerplay: add global PowerPlay mutex.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
