Newer asics have a lot of vram so it's less of an
issue to waste a little more space for the gart
page table. This gives us some additional gart space
before having to migrate to non-gart system ram
for games, etc. where we use up most of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we reset the GPU, we need to properly tear
down power management before reseting the GPU and then
set it back up again after reset. Add the missing
radeon_pm_[suspend|resume] calls to the gpu reset
function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The doorbell aperture is a PCI BAR whose pages can be
mapped to compute resources for things like wptrs
for userspace queues.
This patch maps the BAR and sets up a simple allocator
to allocate pages from the BAR.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UVD ring can't use scratch thus it does need writeback buffer to keep
a valid address or radeon_ring_backup will trigger a kernel fault.
It's ok to not unpin the write back buffer on suspend as it leave in
gtt and thus does not need eviction.
v2: Fix the uvd case.
Reported and tracked by Wojtek <wojtask9@wp.pl>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This narrows the scope of the apple re-POST hack added in:
drm/radeon: re-POST the asic on Apple hardware when booted via EFI
That patch prevents UVD from working on macs when booted in EFI
mode. The original patch fixed macbook2,1 systems which were
r5xx and hence have no UVD. Limit the hack to those systems to
prevent UVD breakage on newer systems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This is to allow debugging of userspace program not freeing buffer
after, which is basicly a memory leak. This print the list of all
gem object along with their size and placement (VRAM,GTT,CPU) and
with the pid of the task that created them.
agd5f: add warning fix
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Golden registers are arrays of register settings from the
hw team that need to be initialized at asic startup.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a per-asic MC (memory controller) mask which holds the
mak address mask the asic is capable of. Use this when
calculating the vram and gtt locations rather using asic
specific functions or limiting everything to 32 bits.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
More drm-next bits for radeon. Just bug fixes.
* 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: properly validate the atpx interface
drm/radeon: switch get_gpu_clock() to a callback (v2)
drm/radeon: add a asic callback to get the xclk
drm/radeon: Avoid NULL pointer dereference from atom_index_iio() allocation failure
drm/radeon: remove overzealous warning in hdmi handling
drm/radeon: fix multi-head power profile stability on BTC+ asics
Smatch anlysis:
drivers/gpu/drm/radeon/atom.c:1242 atom_index_iio() error: potential null
dereference 'ctx->iio'. (kzalloc returns null)
Also cleaned up some checks before calls to kfree(). kfree(NULL) is OK.
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex writes:
- CS ioctl cleanup and unification. Unification of a lot of functionality
that was duplicated across multiple generates of hardware.
- Add support for Oland GPUs
- Deprecate UMS support. Mesa and the ddx dropped support for UMS and
apparently very few people still use it since the UMS CS ioctl was broken
for several kernels and no one reported it. It was fixed in 3.8/stable.
- Rework GPU reset. Use the status registers to determine what blocks
to reset. This better matches the recommended reset programming model.
This also allows us to properly reset blocks besides GFX and DMA.
- Switch the VM set page code to use an IB rather than the ring. This
fixes overflow issues when doing large page table updates using a small
ring like DMA.
- Several small cleanups and bug fixes.
* 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux: (38 commits)
drm/radeon/dce6: fix display powergating
drm/radeon: add Oland pci ids
drm/radeon: radeon-asic updates for Oland
drm/radeon: add ucode loading support for Oland
drm/radeon: fill in gpu init for Oland
drm/radeon: add Oland chip family
drm/radeon: switch back to using the DMA ring for VM PT updates
drm/radeon: use IBs for VM page table updates v2
drm/radeon: don't reset the MC on IGPs/APUs
drm/radeon: use the reset mask to determine if rings are hung
drm/radeon: halt engines before disabling MC (si)
drm/radeon: halt engines before disabling MC (cayman/TN)
drm/radeon: halt engines before disabling MC (evergreen)
drm/radeon: halt engines before disabling MC (6xx/7xx)
drm/radeon: use status regs to determine what to reset (si)
drm/radeon: use status regs to determine what to reset (cayman)
drm/radeon: use status regs to determine what to reset (evergreen)
drm/radeon: use status regs to determine what to reset (6xx/7xx)
drm/radeon: rework GPU reset on cayman/TN
drm/radeon: rework GPU reset on cayman/TN
...
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
vga-switcheroo with apple-gmux does not switch correctly on my system. The PCI
configuration space is not restored correctly, resulting in MSI not working after switch.
Only useful item in dmesg is:
[ 33.922807] radeon 0000:01:00.0: Refused to change power state, currently in D3
I did some testing, dumping the difference in ms between first succesful switch
from D3 to D0, and it seems that there is slightly more than 20 ms difference when
the device is re-enabled through vga-switcheroo.
So bump the re-enable d3 delay to 20 ms to handle this, which fixes msi not working
on my system after switcheroo-ing. Default d3_delay value is PCI_PM_D3_WAIT, 10 ms.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Modeset path seems to conflict sometimes with the memory management
leading to kernel deadlock. This move modesetting reset after GPU
acceleration reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
radeon_fence_wait_empty_locked should not trigger GPU reset as no
place where it's call from would benefit from such thing and it
actually lead to a kernel deadlock in case the reset is triggered
from pm codepath. Instead force ring completion in place where it
makes sense or return early in others.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Force all fence to signal if GPU reset failed so no process get stuck
on waiting fence.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
With the new per-crtc locking mutliple set-cursor calls could happen
in parallel. Out of sheer paranoia I've opted for an irqsave spinlock.
But if there's indeed an access from interrupt contexts to these regs
it's already broken with the old code, so this can likely just be
reduced to a normal spinlock. Otoh the pageflip completion happens
from the vblank irq handler ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GART and VRAM size limits need to be a power of two.
Fix values greater than 1GB and simplify those checks a bit.
v2: also fix radeon_vram_limit usage, and simplify test even more.
v3: agd5f: fix spelling as noticed by Klaus Schnass
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The actual set up and assignment of VM page tables
is done on the fly in radeon_gart.c.
v2: update vm size comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Let's allow GCC to optimize better.
This exposed some five unused functions, but this patch doesn't remove them.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move binding onto the ring, simplifying handling a bit.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
It was only used for dynpm, but has been replaced with
a better implementation using fences. Remove it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds documentation to most of the functions in
radeon_device.c
v2: split out general descriptions as per Christian's
comments.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Just store the index in the ring structure.
Idea taken from one of Jerome's wip rptr patches.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Try to save whatever is on the rings when
we encounter an lockup.
v2: Fix spelling error. Free saved ring data if reset fails.
Add documentation for the new functions.
v3: Some more spelling fixes
v4: It doesn't make sense to save anything if all fences
are signaled
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Making it easier to control when it is executed.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
GPU reset need to be exclusive, one happening at a time. For this
add a rw semaphore so that any path that trigger GPU activities
have to take the semaphore as a reader thus allowing concurency.
The GPU reset path take the semaphore as a writer ensuring that
no concurrent reset take place.
v2: init rw semaphore
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Try to remove or replace the cs_mutex with a
vm_mutex where it is still needed.
v2: fix locking order
v3: rebased on drm-next
Signed-off-by: Christian König <deathsimple@vodafone.de>
The spinlock was actually there to protect the
rptr, but rptr was read outside of the locked area.
Also we don't really need a spinlock here, an
atomic should to quite fine since we only need to
prevent it from being reentrant.
v2: Keep the spinlock....
v3: Back to an atomic again after finding & fixing the real bug.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
It is a rw_semaphore now and only write locked
while changing the clock. Also the lock is renamed
to better reflect what it is protecting.
v2: Keep the ttm_vm_ops on IGPs
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
This adds prime->fd and fd->prime support to radeon.
It passes the sg object to ttm and then populates
the gart entries using it.
Compile tested only.
v2: stub kmap + use new helpers + add reimporting
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All radeon_gem_init() does is initialize the gem objects
list. radeon_device.c does this explicitly. r600+ calls
radeon_gem_init() so the list gets initialized twice. Older
asics don't call it at all and rely on the the init in
radeon_device.c. Just call radeon_gem_init() in radeon_device.c
and remove the explicit calls from all the newer asics.
All asics call radeon_gem_fini() in their fini pathes. That
could possibly be cleaned up too.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This changes the API as a clean-up. Instead of passing multiple
function pointers at each time, introduce a new struct holding the
whole callback functions and pass it to the registration.
The same struct will be used for the upcoming audio client
registration, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It isn't necessary any more and the suballocator seems to perform
even better.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Directly use the suballocator to get small chunks of memory.
It's equally fast and doesn't crash when we encounter a GPU reset.
v2: rebased on new SA interface.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some callers illegal called fence_wait_next/empty
while holding the ring emission mutex. So don't
relock the mutex in that cases, and move the actual
locking into the fence code.
v2: Don't try to unlock the mutex if it isn't locked.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using 64bits fence sequence we can directly compare sequence
number to know if a fence is signaled or not. Thus the fence
list became useless, so does the fence lock that mainly
protected the fence list.
Things like ring.ready are no longer behind a lock, this should
be ok as ring.ready is initialized once and will only change
when facing lockup. Worst case is that we return an -EBUSY just
after a successfull GPU reset, or we go into wait state instead
of returning -EBUSY (thus delaying reporting -EBUSY to fence
wait caller).
v2: Remove left over comment, force using writeback on cayman and
newer, thus not having to suffer from possibly scratch reg
exhaustion
v3: Rebase on top of change to uint64 fence patch
v4: Change DCE5 test to force write back on cayman and newer but
also any APU such as PALM or SUMO family
v5: Rebase on top of new uint64 fence patch
v6: Just break if seq doesn't change any more. Use radeon_fence
prefix for all function names. Even if it's now highly optimized,
try avoiding polling to often.
v7: We should never poll the last_seq from the hardware without
waking the sleeping threads, otherwise we might lose events.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A single global mutex for ring submissions seems sufficient.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use family rather than DCE check for clarity, also always use
wb on APUs, there will never be AGP variants.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of all this humpy pumpy with recursive
mutex (which also fixes only halve of the problem)
move the actual gpu reset out of the fence code,
return -EDEADLK and then reset the gpu in the
calling ioctl function.
v2: Split removal of radeon_mutex into separate patch.
Return -EAGAIN if reset is successful.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As discussed with Michel that name better
describes the behavior of this function.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It makes no sense at all to have more than one flag.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This closes a race seen with kexec where we enable PCI bus mastering
but the card has been reinitialised fully yet.
This was previously fixed by a patch from Jerome, but this should
close the race completely.
v2: add SI support as suggested by Alex.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename the function to better match the functionality.
DCPLL became PLL0 on DCE6.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling the outputs when the device is suspended can result in erroneous
status updates. Disable output polling during suspend to prevent this
from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If GPU lockup is detected in ib_pool get we are holding the ib_pool
mutex that will be needed by the GPU reset code. As ib_pool code is
safe to be reentrant from GPU reset code we should not block if we
are trying to get the ib pool lock on the behalf of the same userspace
caller, thus use the radeon_mutex_lock helper.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We really only need to set it up once on init or resume
rather than on every mode set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Virtual address space are per drm client (opener of /dev/drm).
Client are in charge of virtual address space, they need to
map bo into it by calling DRM_RADEON_GEM_VA ioctl.
First 16M of virtual address space is reserved by the kernel.
Once using 2 level page table we should be able to have a small
vram memory footprint for each pt (there would be one pt for all
gart, one for all vram and then one first level for each virtual
address space).
Plan include using the sub allocator for a common vm page table
area and using memcpy to copy vm page table in & out. Or use
a gart object and copy things in & out using dma.
v2: agd5f fixes:
- Add vram base offset for vram pages. The GPU physical address of a
vram page is FB_OFFSET + page offset. FB_OFFSET is 0 on discrete
cards and the physical bus address of the stolen memory on
integrated chips.
- VM_CONTEXT1_PROTECTION_FAULT_DEFAULT_ADDR covers all vmid's >= 1
v3: agd5f:
- integrate with the semaphore/multi-ring stuff
v4:
- rebase on top ttm dma & multi-ring stuff
- userspace is now in charge of the address space
- no more specific cs vm ioctl, instead cs ioctl has a new
chunk
v5:
- properly handle mem == NULL case from move_notify callback
- fix the vm cleanup path
v6:
- fix update of page table to only happen on valid mem placement
v7:
- add tlb flush for each vm context
- add flags to define mapping property (readable, writeable, snooped)
- make ring id implicit from ib->fence->ring, up to each asic callback
to then do ring specific scheduling if vm ib scheduling function
v8:
- add query for ib limit and kernel reserved virtual space
- rename vm->size to max_pfn (maximum number of page)
- update gem_va ioctl to also allow unmap operation
- bump kernel version to allow userspace to query for vm support
v9:
- rebuild page table only when bind and incrementaly depending
on bo referenced by cs and that have been moved
- allow virtual address space to grow
- use sa allocator for vram page table
- return invalid when querying vm limit on non cayman GPU
- dump vm fault register on lockup
v10: agd5f:
- Move the vm schedule_ib callback to a standalone function, remove
the callback and use the existing ib_execute callback for VM IBs.
v11:
- rebase on top of lastest Linus
v12: agd5f:
- remove spurious backslash
- set IB vm_id to 0 in radeon_ib_get()
v13: agd5f:
- fix handling of RADEON_CHUNK_ID_FLAGS
v14:
- fix va destruction
- fix suspend resume
- forbid bo to have several different va in same vm
v15:
- rebase
v16:
- cleanup left over of vm init/fini
v17: agd5f:
- cs checker
v18: agd5f:
- reworks the CS ioctl to better support multiple rings and
VM. Rather than adding a new chunk id for VM, just re-use the
IB chunk id and add a new flags for VM mode. Also define additional
dwords for the flags chunk id to define the what ring we want to use
(gfx, compute, uvd, etc.) and the priority.
v19:
- fix cs fini in weird case of no ib
- semi working flush fix for ni
- rebase on top of sa allocator changes
v20: agd5f:
- further CS ioctl cleanups from Christian's comments
v21: agd5f:
- integrate CS checker improvements
v22: agd5f:
- final cleanups for release, only allow VM CS on cayman
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We often end up missing fences on older asics with
writeback enabled which leads to delays in the userspace
accel code, so just disable it by default on those asics.
Reported-by: Helge Deller <deller@gmx.de>
Reported-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allow to share the ib pool with semaphore and avoid
having more bo around.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
That naming seems to make more sense, since we not
only want to run PM4 rings with it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tests syncing between all rings by using
semaphores and fences.
v2: use radeon_testing as a bit flag rather than on/off switch
this allow to test for one thing at a time (bo_move or semaphore
test). It kind of break the usage if user wheren't using 1
for bo move test but as it's a test feature i believe it's ok.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace cp, cp1 and cp2 members with just an array
of radeon_cp structs.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having registered debugfs files globally causes
the files to not show up on the second, third
etc.. card in the system.
v2: fix crash on module unloading
v3: fix space indentation
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
With the exception that we do not handle the AGP case. We only
deal with PCIe cards such as ATI ES1000 or HD3200 that have been
detected to only do DMA up to 32-bits.
V2 force dma32 if we fail to set bigger dma mask
V3 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V4 add debugfs entry is swiotlb is active not only if we are
on dma 32bits only gpu
CC: Dave Airlie <airlied@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
This was only the case if the GPU reset was triggered from the CS ioctl,
otherwise other processes could happily enter the CS ioctl and wreak havoc
during the GPU reset.
This is a little complicated because the GPU reset can be triggered from the
CS ioctl, in which case we're already holding the mutex, or from other call
paths, in which case we need to lock the mutex. AFAICT the mutex API doesn't
allow recursive locking or finding out the mutex owner, so we need to handle
this with helper functions which allow recursive locking from the same
process.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots of new (and hopefully useful) benchmark. Load the driver
with radeon_benchmark=<test_number> and enjoy. Among tests
added are VRAM to VRAM blits and blits with buffer size sweeps.
The latter can be from GTT to VRAM, VRAM to GTT, and VRAM to VRAM
and there are two types of sweeps: powers of two and (probably
more interesting) buffers sizes that correspond to common modes.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a card wasn't PCIE, we always set the DMA mask to 32 bits.
This is only applies to the old rage128/r1xx gart block on
early radeon asics (~r1xx-r4xx). Newer PCI and IGP cards
can handle 40 bits just fine.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Chen Jie <chenj@lemote.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value of RADEON_DEBUGFS_MAX_NUM_FILES has been used to
specify the size of an array, each element of which looks
like this:
struct radeon_debugfs {
struct drm_info_list *files;
unsigned num_files;
};
Consequently, the number of debugfs files may be much greater
than RADEON_DEBUGFS_MAX_NUM_FILES, something that the current
code ignores:
if ((_radeon_debugfs_count + nfiles) > RADEON_DEBUGFS_MAX_NUM_FILES) {
DRM_ERROR("Reached maximum number of debugfs files.\n");
DRM_ERROR("Report so we increase RADEON_DEBUGFS_MAX_NUM_FILES.\n");
return -EINVAL;
}
This commit fixes this make, and accordingly renames:
RADEON_DEBUGFS_MAX_NUM_FILES
to:
RADEON_DEBUGFS_MAX_COMPONENTS
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least some Apples program the GPU into a state that wedges the engine
once userspace starts trying to perform accelerated operations. Executing
the Atom init scripts gets the hardware back into a working state. The
same hardware works fine when booted via BIOS emulation, so let's just
execute the init scripts on Apples when we're using EFI.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Log PCI subsystem vendor and subsystem device ID in addition to
PCI vendor and device ID during kernel mode initialisation. This helps
to better identify radeon devices of third-party vendors, e. g. for
bug analysis.
Tested for kernel 2.6.35, 2.6.38 and 3.0 on Asus M2A-VM HDMI board
Cc: <stable@kernel.org>
Signed-off-by: Thomas Reim <reimth@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Stephen Michaels <Stephen.Micheals@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
It only needs to be called once at startup, not for every
modeset.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
Cayman is DCE5 display plus a new 4-way shader block.
3D state programming is similar to evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
... and switch it to container_of upcasting.
v2: converted new pageflip code-paths.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unconditionally initialize the drm gem object - it's not
worth the trouble not to for the few kernel objects.
This patch only changes the place of the drm gem object,
access is still done via pointers.
v2: Uncoditionally align the size in radeon_bo_create. At
least the r600/evergreen blit code didn't to this, angering
the paranoid gem code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.
This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With cmwq, there's no reason for radeon to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.
Because radeon_driver_irq_uninstall_kms() may be called from
unsleepable context, the work items can't be flushed from there.
Instead, init and flush from radeon_irq_kms_init/fini().
While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work.
Always initialize and sync cancel instead of being unnecessarily smart
about it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On r6xx+ a newer fence mechanism was implemented to replace
the old wait_until plus scratch regs setup. A single EOP event
will flush the destination caches, write a fence value, and generate
an interrupt. This is the recommended fence mechanism on r6xx+ asics.
This requires my previous writeback patch.
v2: fix typo that enabled event fence checking on all asics
rather than just r6xx+.
v3: properly enable EOP interrupts
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=29972
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory. The driver can then read
the values from the shadow rather than reading back from the
register across the bus. Writeback can be disabled by setting
the no_wb module param to 1.
On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer
v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than calling get_memory_clock and get_engine_clock,
used the tracked values from the pm code. Calling the tables
adds additional latency in the modesetting and pm paths.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GTT/VRAM overlapping test had a typo which leaded to not
detecting case when vram_end > gtt_end. This patch fix the
logic and should fix#16574
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
0 is a valid DMA address from pci_map_page(), use pci_dma_mapping_error()
instead to check for errors
[airlied: fix warning + two other places with errors.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we were not able to map the io bar in device init, don't attempt
to unmap it in device fini. All radeons should have a io bar, so
I doubt this would ever trigger, but just to be on the safe side...
Pointed out by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required for the NB_MISC regs on rs780/rs880 which
means HDMI/DVI/DP ports using PCIEPHY won't work without
it. It might also help with s/r (asic init) issues on other
atombios cards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28774
and similar issues reported by Alberto Milone.
[airlied: Squash io fix patch]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
When suspending, we turn the display hw off, at resume the screen will stay black.
This patch turn it on. Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16180
Signed-off-by: Cedric Godin <cedric.godin@skynet.be>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.
[airlied: fixup nouveau properly to build]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useful for certain power management operations. You
need to wait for the GUI engine (2D, 3D, CP, etc.) to be
idle before changing clocks or adjusting engine parameters.
(v2) Fix gui idle enable on pre-r6xx asics
(v3) The gui idle interrrupt status bit is permanently asserted
on pre-r6xx chips, but the interrrupt is still generated.
workaround it in the driver.
(v4) Add support for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
of the times but once in a while it fails for no obvious
reasons (same status than previous reset just no same
happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
it seems that it can fail after a bunch (reset every
2sec for 3hour bring down the GPU & computer)
This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).
Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.
Next step is to record the bogus command that leaded to
the lockup.
V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RS4xx+ IGP chips use an internal gart, however,
some of them have the agp cap bits set in their pci
configs. Make sure to clear the AGP flag as AGP will
not work with them.
Should fix fdo bug 27225
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
And move asic init plus a few related functions from radeon_device.c
to it. This file will hold all the asic structures in the future,
but atm they're still stuck in radeon_asic.h.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.
I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.
Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
V2: reorganize functions, fix modesetting calls
V3: rebase patch, use radeon's workqueue
V4: enable on tested chipsets only, request VBLANK IRQs
V5: enable PM on older hardware (IRQs, mode_fixup, dpms)
V6: use separate dynpm module parameter
V7: drop RADEON_ prefix, set minimum mode for dpms off
V8: update legacy encoder call, fix order in rs600 IRQ
V9: update compute_clocks call in legacy, not only DPMS_OFF
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
wire hw i2c support into radeon i2c algo.
fixes merged:
- handle bus probing correctly
- use meaningful error numbers
- abort if transaction fails
- The line mapping is different depending on the asic.
- protect hw i2c engine with a mutex
- rs300 doesn't have a pin select bit
- r200 has a different pin select setup
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use same common function to disable agp so we replace the GART
callback by the proper one when we do so. This fix oops if
radeon_agp_init report failure.
This patch also move radeon_agp_init out of *_mc_init for r600
& rv770 so that we can have a similar behavior than for previous
hw, ie if agp_init fails it will fallback to GPU GART and disable
AGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13335
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add a function which check module argument to be
valid. On invalid argument it prints a warning and setback
the default value.
V2: Allow 0 for vram limit & agp mode which are the default
value
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just adds a mutex around the atombios table execution
so we don't call it from two contexts at once.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
