This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0
For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.
Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.
This patch thus updates the reset code to more closely
match the reference driver:
- soft reset (pdc_reset_port):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* write reset bit in PDC_CTLSTAT before the first read
in the loop
* for 2nd gen SATA follow up with FPDMA reset and clearing
error status registers
- hard reset (pdc_sata_hardreset):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* reset ATA engine via the PCI control register
* Tejun's change to use non-waiting hardreset + follow-up SRST
I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).
Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.
The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.
Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 54c38444fa makes libata abort qcs
after the port is frozen. This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error. However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously. Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit a5bfc4714b dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the duplicate comment of bstr_printf that is the same as the
vsnprintf.
Add the 's' option to the comment for the pointer function. This is
more of an internal function so the little duplication of the comment
here is OK.
Reported-by: Zhaolei <zhaolei@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With BLOCK_IOPOLL_SOFTIRQ added, softirq_to_name[] and
show_softirq_name() needs to be updated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB20398.8070209@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
commit 85bac32c4a
ring-buffer: only enable ring_buffer_swap_cpu when needed
broke oprofile (at least on s390, but likely on all platforms).
this patch lets oprofile select RING_BUFER_ALLOW_SWAP to make
ring_buffer_swap_cpu usable for oprofile.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
LKML-Reference: <200909162156.49239.borntraeger@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
For direct function pointers (like what mcount provides) PowerPC64
requires the use of %ps, otherwise nothing is printed.
This patch converts all prints of functions retrieved through mcount
to use the %ps format from the %pf.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On PowerPC64 function pointers do not point directly at the functions,
but instead point to pointers to the functions. The output of %pF expects
to point to a pointer to the function, whereas %pS will show the function
itself.
mcount returns the direct pointer to the function and not the pointer to
the pointer. Thus %pS must be used to show this. The function tracer
requires printing of the functions without offsets and uses the %pf
instead.
%pF produces run_local_timers+0x4/0x1f
%pf produces just run_local_timers
For PowerPC64, we need to use the direct pointer, and we only have
%pS which will produce .run_local_timers+0x4/0x1f
This patch creates a %ps that matches the %pf as %pS matches %pF.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* fix/asoc:
ASoC: remove unused #include <linux/version.h>
ASoC: S3C lrsync function made to work with IRQs disabled.
ASoC: Fix display of stream name in DAPM debugfs
ASoC: Clean up error handling in MPC5200 DMA setup
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Todo: Nothing ever detects CPU_BCM6338 but the code tests for it anyway.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is a bunch of platform device registration in
arch/mips/cavium-octeon/setup.c. We move it to its own file in
preparation for adding more platform devices.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code after the vmalloc_fault: label in do_page_fault() modifies
user page tables, this is not correct for 64-bit kernels.
For 64-bit kernels we should go straight to the no_context handler
skipping vmalloc_fault.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
By combining swapper_pg_dir and module_pg_dir, several if conditions
can be eliminated from the tlb exception handler. The reason they
can be combined is that, the effective virtual address of vmalloc
returned is at the bottom, and of module_alloc returned is at the
top. It also fixes the bug in vmalloc(), which happens when its
return address is not covered by the first pgd.
Signed-off-by: Wu Fei <at.wufei@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
loops_per_jiffy depends on coreclk speed; preset it instead of
letting the kernel waste precious microseconds trying to approximate it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a platform device for the Octeon Random Number Generator (RNG).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the 'allow_au1k_wait' variable. MIPS kernel installs the
Alchemy-specific wait code before timer initialization; if the C0
timer must be used for timekeeping the wait function is set to NULL
which means no wait implementation is available.
As a sideeffect, the 'wait instruction available' output in
/proc/cpuinfo now correctly indicates whether 'wait' is usable.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On some CPUs, it is more efficient to disable and enable interrupts in the
kernel rather than use ll/sc for atomic operations. But if we were to set
cpu_has_llsc to false, we would break the userspace futex interface (in
asm/futex.h).
We separate the two concepts, with a new predicate kernel_uses_llsc, that
lets us disable the kernel's use of ll/sc while still allowing the futex
code to use it.
Also there were a couple of cases in bitops.h where we were using ll/sc
unconditionally even if cpu_has_llsc were false.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_CPU_HAS_LLSC duplicated the function of cpu_has_llsc for no good
reason and and the results if the one was enabled and the other disabled
was very unobvious. Remove it now that there are no more remaining users.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch results in fewer output sections and in some data being
reordered, but should have no functional impact.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that PAGE_SIZE is available to assembly directly, there is no need
to separately expose it as _PAGE_SIZE through asm-offsets.
In addition, remove _PAGE_SHIFT from asm-offsets, since it was never
needed, and is not used anywhere.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the board code register the ar7_wdt driver as a platform
device. We move the dynamic resource calculation here since the driver
should not be aware of the AR7 SoC version it is running on.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Because only gcc >=4.4 have loongson-specific support, we need to choose
the suitable -march argument for gcc <= 4.3 and gcc >= 4.4, and here, we
use -march=loongson2e for loongson2e.
Thanks goes to Arnaud Patard <apatard@mandriva.com> for suggestion of
using cc-options(Documentation/kbuild/makefiles.txt). and thanks Zhang
Le for introducing the new CPU_LOONGSON2E kernel option.
NOTE: -mtune option is not need if -march and -mtune use the same value.
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The difference between some loongson-based machines is very small, so, if
there is no necessary to add new kernel config options to cope with this
difference, it will be better to share the same kernel image file between
them, benefit from this, the linux distribution developers only have a need
to compile the kernel one time.
This machtype kernel command line argument will be used later to share the
same kernel image file between two different machines(menglong & yeeloong)
made by lemote.
Thanks very much to Zhang Le for cleaning up the machtype implementation.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To share common loongson source code between all of the loongson-based
machines. there is a need to split it out of the fuloong-2e/ directory.
at the same time, other according tuning is needed. the machine-specific
parts are defined as macros in relative header file, pci.h, mem.h,
machine.h.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To make source code of loongson sharable to the machines(such as gdium)
made by the other companies, we rename arch/mips/lemote to
arch/mips/loongson, asm/mach-lemote to asm/mach-loongson, and rename lm2e
to the name of the machine: fuloong-2e. accordingly, FULONG are renamed to
FULOONG2E to make it distinguishable to the future FULOONG2F. and also,
some other relative tuning is needed.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This kernel support is needed by the user-space tool:oprofile to profile
linux kernel or applications via loongson2 performance counters. you can
enable this driver via CONFIG_OPROFILE = y or m.
On Loongson2 there are two performance counters, each one can count 16
events respectively. when anyone of the performance counter overflows, an
interrupt will be generated and is routed to the IRQ MIPS_CPU_IRQ_BASE + 6.
Signed-off-by: Yanhua <yanh@lemote.com>
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RTC_LIB is selected by MIPS by default, and therefore, the legacy RTC
driver is disabled. but fortunately, RTC_LIB not works on fulong, so,
enabling the legcy RTC driver is needed, otherwise, the tools like
hwclock will not work.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixup the wrong original comment of pcimap, and make the source code more
understandable. and also, some new extra consideration is added in.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the help of script/checkpatch.pl, i have cleaned up the coding
style.
1. remove un-needed header files and tune some comments.
2. remove some un-needed { }
add a new header file loongson.h:
3. move some common header files to loongson.h
4. move some common extern declartions to loongson.h
and this new header file is needed for future loongson2f support.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch split the old initilization and setup implementation to
several file, one file one logic function.
the other main changes include:
1. as the script/checkpatch.pl suggests, use strict_strtol instead
of simple_strtol in arch/mips/lemote/lm2e/cmdline.c
2. use the existed macros in asm/mips-boards/bonito64.h as the
arguments of set_io_port_base() and remove the un-needed ones in
asm/mach-lemote/pci.h
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips_io_port_base is initialized via set_io_port_base() in
arch/mips/lemote/lm2e/setup.c, we can use it directly here.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several magic numbers have been replaced by relative macros, which will be
more readable and understandable.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The implmentation of loongson2e_power_off and loongson2e_halt is almostly
the same, just preserve one of them.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
