This is a leftover from the 31 bit area. For CONFIG_64BIT the usual
operation "y = x | PSW_ADDR_AMODE" is a nop. Therefore remove all
usages of PSW_ADDR_AMODE and make the code a bit less confusing.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Finally get rid of the leading underscore. I tried this already two or
three years ago, however Michael Holzheu objected since this would
break the crash utility (again).
However Michael integrated support for the new name into the crash
utility back then, so it doesn't break if the name will be changed
now. So finally get rid of the ever confusing leading underscore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To collect the CPU registers of the crashed system allocated a single
page with memblock_alloc_base and use it as a copy buffer. Replace the
stop-and-store-status sigp with a store-status-at-address sigp in
smp_save_dump_cpus() and smp_store_status(). In both cases the target
CPU is already stopped and store-status-at-address avoids the detour
via the absolute zero page.
For kexec simplify s390_reset_system and call store_status() before
the prefix register of the boot CPU has been set to zero. Use STPX
to store the prefix register and remove dump_prefix_page.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow to ipl from CCW based devices residing in any subchannel set.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The input buffer in reipl_fcp_scpdata_write is accessed out of bounds
when an offset is specified. The problem is that the offset refers to
the data we should write to and not to the buffer we read from.
So instead of
memcpy(scp_data, buf + off, count);
we could just do
memcpy(scp_data + off, buf, count);
However we not only modify the data but also store its length. For this to
work we'd need to remember a state per open FH. Since that's not possible
with sysfs callbacks let's just fail when an offset is specified.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce /sys/debug/kernel/diag_stat with a statistic how many diagnose
calls have been done by each CPU in the system.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ipl.c uses 3 different macros to create a sysfs show function for ipl
attributes. Define IPL_ATTR_SHOW_FN which is used by all macros.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use macros wherever applicable and create a shutdown_action attribute
group to simplify the code.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use macros wherever applicable and put bin_attributes inside attribute_groups
to simplify/remove some code.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e58 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loadparm is only supported for CCW IPL. But also for SCSI
IPL it can be specified either on the HMC load panel respectively
z/VM console or via diagnose 308.
So fix this for SCSI and add the required sysfs attributes for reading the
IPL loadparm and for setting the loadparm for re-IPL.
With this patch the following two sysfs attributes are introduced:
- /sys/firmware/ipl/loadparm (for system that have been IPLed from SCSI)
- /sys/firmware/reipl/fcp/loadparm
Because the loadparm is now available for SCSI and CCW it is moved
now from "struct ipl_block_ccw" to the generic "struct ipl_list_hdr".
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For CCW and SCSI IPL the hardware sets the subchannel ID and number
correctly at 0xb8. For kdump at 0xb8 normally there is the data of
the previously IPLed system.
In order to be clean now for kdump and kexec always set the subchannel
ID and number to zero. This tells the next OS that no CCW/SCSI IPL
has been done.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Simplify the uaccess code by removing the user_mode=home option.
The kernel will now always run in the home space mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The following git commit changed the behavior of sscanf:
commit 53809751ac
Author: Jan Beulich <JBeulich@suse.com>
Date: Mon Dec 17 16:01:31 2012 -0800
sscanf: don't ignore field widths for numeric conversions
This broke the WWPN and LUN sysfs attributes for s390 reipl and dump
on panic.
Example:
$ echo 0x0123456701234567 > /sys/firmware/reipl/fcp/wwpn
$ cat /sys/firmware/reipl/fcp/wwpn
0x0001234567012345
So fix this and use format strings that work also with the
new sscanf implementation:
$ echo 0x012345670123456789 > /sys/firmware/reipl/fcp/wwpn
$ cat /sys/firmware/reipl/fcp/wwpn
0x0123456701234567
Cc: stable@vger.kernel.org # 3.8+
Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a zfcpdump is triggered and a second dump on the same CEC is
already in progress for another LPAR, diagnose 308 returns with
an error code until the first dump is finished. Currently the
second Linux stops with a disabled wait PSW in that case.
This is improved now by by triggering diag 308 in a loop until
it works.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the vmcmd shutdown action is parsed by the kernel and
if multiple cp commands have been specified, they are issued
separately with the cpcmd() function.
The underlying diagnose 8 instruction already allows to specify
multiple commands that are separated by 0x15. The ASCEBC() function
used by cpcmd() translates '\n' to 0x15. The '\n' character is
currently used as vmcmd command separator and therefore the vmcmd
string can be passed directly to the cpcmd() function.
Using the diagnose 8 command separation has the advantage that also
after disruptive commands that stop Linux, for example "def store",
additional commands can be executed.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Fix problem that was introduced with patch "s390/smp: make absolute
lowcore / cpu restart parameter". After that patch the "dumpreipl"
shutdown action does not work any more. To fix the problem we have
to assign "reipl_block_actual" instead of "&reipl_block_actual"
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setting the cpu restart parameters is done in three different fashions:
- directly setting the four parameters individually
- copying the four parameters with memcpy (using 4 * sizeof(long))
- copying the four parameters using a private structure
In addition code in entry*.S relies on a certain order of the restart
members of struct _lowcore.
Make all of this more robust to future changes by adding a
mem_absolute_assign(dest, val) define, which assigns val to dest
using absolute addressing mode. Also the load multiple instructions
in entry*.S have been split into separate load instruction so the
order of the struct _lowcore members doesn't matter anymore.
In addition move the prototypes of memcpy_real/absolute from uaccess.h
to processor.h. These memcpy* variants are not related to uaccess at all.
string.h doesn't seem to match as well, so lets use processor.h.
Also replace the eight byte array in struct _lowcore which represents a
misaliged u64 with a u64. The compiler will always create code that
handles the misaligned u64 correctly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the new function memcpy_absolute() that allows to
copy memory using absolute addressing. This means that the prefix swap
does not apply when this function is used.
With this patch also all s390 kernel code that accesses absolute zero
now uses the new memcpy_absolute() function. The old and less generic
copy_to_absolute_zero() function is removed.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the PSW restart handler and kexec are executed in real
mode with DAT=off. For kexec/kdump the function setup_regs() is
called that uses the per-cpu variable "crash_notes". Because
there are situations when the per-cpu implementation uses vmalloc
memory, calling setup_regs() in real mode can cause a program
check interrupt.
To fix that problem this patch changes the following:
* Ensure that diag308_reset() does not change PSW bits to real mode
* Enable DAT in __do_restart() after we switched to an online CPU
* Enable DAT in __machine_kexec() after we switched to the IPL CPU
* Call setup_regs() before we switch to real mode and call purgatory
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to allow kdump based stand-alone dump, some information
has to be passed from the old kernel to the new dump kernel. This
is done via a the struct "os_info" that contains the following fields:
* crashkernel base and size
* reipl block
* vmcoreinfo
* init function
A pointer to os_info is stored at a well known storage location
and the whole structure as well as all fields are secured with
checksums.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the following mechanisms are available to move active
Linux on System z instances between machines:
* z/VM 6.2 SSI (Single System Image)
* Suspend/resume
For moving Linux instances in this patch the term LGR (Linux Guest
Relocation) is used. Because such an operation is critical, it
should be detectable from Linux. With this patch for both, a live
system and a kernel dump, the information about LGRs is accessible.
To identify a guest, stsi and stfle data is used. A new function
lgr_info_log() compares the current data (lgr_info_cur) with the
last recorded one (lgr_info_last). In case the two data sets differ,
lgr_info_cur is logged to the "lgr" s390dbf.
The following trigger points call lgr_info_log():
* panic
* die
* kdump
* LGR timer
* PSW restart
* QDIO recovery
* resume
This patch also changes the s390dbf hex_ascii view. Now only printable ASCII
characters are shown.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the new copy_to_absolute_zero() function instead of manual "stura"
and "sturg" to make the code shorter and more readable.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
PSW restart can be triggered on offline CPUs. If this happens, currently
the PSW restart code fails, because functions like smp_processor_id()
do not work on offline CPUs. This patch fixes this as follows:
If PSW restart is triggered on an offline CPU, the PSW restart (sigp restart)
is done a second time on another CPU that is online and the old CPU is
stopped afterwards.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The main purpose for PSW restart will be kdump. Therefore customers will
issue "system restart" for creating a dump. If kdump is not enabled,
currently "PSW restart" will reboot the system and then no dump can
be created any more. In order to still allow a manual stand-alone dump in
the case a user issues "PSW restart" on a system that has not enabled
kdump we now stop the system.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
reipl_fcp_kset was just initialized, so it appears that it should be tested
instead of reipl_kset.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reported-by: Suman Saha <sumsaha@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The diagnose 308 call is the prefered method for clearing all ongoing I/O.
Therefore if it is available we use it instead of doing a manual reset.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
With this patch a new S390 shutdown trigger "restart" is added. If under
z/VM "systerm restart" is entered or under the HMC the "PSW restart" button
is pressed, the PSW located at 0 (31 bit) or 0x1a0 (64 bit) bit is loaded.
Now we execute do_restart() that processes the restart action that is
defined under /sys/firmware/shutdown_actions/on_restart. Currently the
following actions are possible: reipl (default), stop, vmcmd, dump, and
dump_reipl.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ENOTSUPP is not supposed to leak to userspace so lets just use
EOPNOTSUPP everywhere.
Doesn't fix a bug, but makes future reviews easier.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename signal_processor* functions to sigp*.
Add raw variants of each version, so we can get rid of the hacks played
in smp code which establish temporary cpu logical mappings so they could
call the sigp functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Always reboot on logical cpu 0. This makes sure that the IPL cpu is
always the same and usually avoids strange numbering schemes between
physical and logical cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
According to the architecture a cpu must not necessarily enter stopped
state after completion of a sigp instruction with "stop" order code.
So remove the BUG() statement after self sending sigp stop to avoid
that it ever gets reached.
Also add a sigp busy check to make sure that the order gets delivered.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the CP SET LOADDEV on the 3215 console has been used to specify
SCPdata, all data is converted to upper case letters.
When scpdata contains upper case letters only, convert all letters
to lower case.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Append scpdata to the kernel boot command line. If scpdata starts
with the equal sign (=), the kernel boot command line is replaced.
(For consistency with zIPL and IPL PARM parameters.)
To use scpdata for the kernel boot command line, scpdata must consist
of ascii characters only. If scpdata contains other characters,
scpdata is not appended to the kernel boot command line.
In addition, re-IPL is extended for setting scpdata for the next
Linux reboot.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We always returned -EINVAL when setting of a shutdown action failed. This was
misleading, if for example the hardware did not support the shutdown action.
Now we save each shutdown action's init return code and return it when the
action is being set.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this for !CONFIG_SMP:
arch/s390/kernel/ipl.c: In function 'stop_run':
arch/s390/kernel/ipl.c:1461: error: implicit declaration of function 'signal_processor'
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 ipl panic notifier will stop the system or trigger a system dump.
This should be done as final action on the panic path. All other panic
notifiers should be executed before. Currently we use priority 0 for the ipl
notifier. In order to be called late, this patch changes the priority to
INT_MIN which is the lowest possible priority.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A code analysis tool reported two warnings:
"The expression `ipl_info.type == IPL_TYPE_FCP' is true whenever evaluated."
and "Default is not possible". This patch improves the corresponding if
statement logic and removes the unnecessary switch defaults.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
