When turning branch instructions into NOPs, we attempt to validate the
action by comparing the old value at the call site with the opcode of
a direct relative branch instruction pointing at the old target.
However, these call sites are statically initialized to call _mcount(),
and may be redirected via a PLT entry if the module is loaded far away
from the kernel text, leading to false negatives and spurious errors.
So skip the validation if CONFIG_ARM64_MODULE_PLTS is configured.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Wire up the existing arm64 support for SMBIOS tables (aka DMI) for ARM as
well, by moving the arm64 init code to drivers/firmware/efi/arm-runtime.c
(which is shared between ARM and arm64), and adding a asm/dmi.h header to
ARM that defines the mapping routines for the firmware tables.
This allows userspace to access these tables to discover system information
exposed by the firmware. It also sets the hardware name used in crash
dumps, e.g.:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ed3c0000
[00000000] *pgd=bf1f3835
Internal error: Oops: 817 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 759 Comm: bash Not tainted 4.10.0-09601-g0e8f38792120-dirty #112
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
^^^
NOTE: This does *NOT* enable or encourage the use of DMI quirks, i.e., the
the practice of identifying the platform via DMI to decide whether
certain workarounds for buggy hardware and/or firmware need to be
enabled. This would require the DMI subsystem to be enabled much
earlier than we do on ARM, which is non-trivial.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602135207.21708-14-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 3fde2999fa ("arm64: cpufeature: Don't dump useless backtrace on
CPU_OUT_OF_SPEC") changed the cpufeature detection code to use add_taint
instead of WARN_TAINT_ONCE when detecting a heterogeneous system with
mismatched feature support. Unfortunately, this resulted in all systems
getting the taint, regardless of any feature mismatch.
This patch fixes the problem by conditionalising the taint on detecting
a feature mismatch.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that some functions that deal with arch topology information live
under drivers, there is a clash of naming that might create confusion.
Tidy things up by creating a topology namespace for interfaces used by
arch code; achieve this by prepending a 'topology_' prefix to driver
interfaces.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a new header file (include/linux/arch_topology.h) and put there
declarations of interfaces used by arm, arm64 and drivers code.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the scope of cap_parsing_failed (making it static in
drivers/base/arch_topology.c) by slightly changing {arm,arm64} DT
parsing code.
For arm checking for !cap_parsing_failed before calling normalize_
cpu_capacity() is superfluous, as returning an error from parse_
cpu_capacity() (above) means cap_from _dt is set to false.
For arm64 we can simply check if raw_capacity points to something,
which is not if capacity parsing has failed.
Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm and arm64 share lot of code relative to parsing CPU capacity
information from DT, using that information for appropriate scaling and
exposing a sysfs interface for chaging such values at runtime.
Factorize such code in a common place (driver/base/arch_topology.c) in
preparation for further additions.
Suggested-by: Will Deacon <will.deacon@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perf has supported ARMv8.1 feature with 16-bit evtCount filed [see c210ae8
arm64: perf: Extend event mask for ARMv8.1], event config should be
extended to 16-bit too, otherwise, if use -e event_name whose event_code
is more than 0x3ff, pmu_config_term will return -EINVAL because function
pmu_format_max_value depends on event config.
This patch extends event config to 16-bit.
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
PCI core requires the NUMA node for the struct pci_host_bridge.dev to
be set by using the pcibus_to_node(struct pci_bus*) API, that on ARM64
systems relies on the struct pci_host_bridge->bus.dev NUMA node.
The struct pci_host_bridge.dev NUMA node is then propagated through
the PCI device hierarchy as PCI devices (and bridges) are enumerated
under it.
Therefore, in order to set-up the PCI NUMA hierarchy appropriately, the
struct pci_host_bridge->bus.dev NUMA node must be set before core
code calls pcibus_to_node(struct pci_bus*) on it so that PCI core can
retrieve the NUMA node for the struct pci_host_bridge.dev device and can
propagate it through the PCI bus tree.
On ARM64 ACPI based systems the struct pci_host_bridge->bus.dev NUMA
node can be set-up in pcibios_root_bridge_prepare() by parsing the root
bridge ACPI device firmware binding.
Add code to the pcibios_root_bridge_prepare() that, when booting with
ACPI, parse the root bridge ACPI device companion NUMA binding and set
the corresponding struct pci_host_bridge->bus.dev NUMA node
appropriately.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It's useless to print machine name and setup arch-specific system
identifiers if of_flat_dt_get_machine_name() return NULL, especially
when ACPI-based boot.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Unfortunately, it turns out that mismatched CPU features in big.LITTLE
systems are starting to appear in the wild. Whilst we should continue to
taint the kernel with CPU_OUT_OF_SPEC for features that differ in ways
that we can't fix up, dumping a useless backtrace out of the cpufeature
code is pointless and irritating.
This patch removes the backtrace from the taint.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Generic code expects show_regs() to dump the stack, but arm64's
show_regs() does not. This makes it hard to debug softlockups and
other issues that result in show_regs() being called.
This patch updates arm64's show_regs() to dump the stack, as common
code expects.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[will: folded in bug_handler fix from mrutland]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Generic code expects show_regs() to also dump the stack, but arm64's
show_reg() does not do this. Some arm64 callers of show_regs() *only*
want the registers dumped, without the stack.
To enable generic code to work as expected, we need to make
show_regs() dump the stack. Where we only want the registers dumped,
we must use __show_regs().
This patch updates code to use __show_regs() where only registers are
desired. A subsequent patch will modify show_regs().
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The text patching functions which are invoked from jump_label and kprobes
code are protected against cpu hotplug at the call sites.
Use stop_machine_cpuslocked() to avoid recursion on the cpu hotplug
rwsem. stop_machine_cpuslocked() contains a lockdep assertion to catch any
unprotected callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081549.197070135@linutronix.de
Commit 093d24a204 ("arm64: PCI: Manage controller-specific data on
per-controller basis") added code to allocate ACPI PCI root_ops
dynamically on a per host bridge basis but failed to update the
corresponding memory allocation failure path in pci_acpi_scan_root()
leading to a potential memory leakage.
Fix it by adding the required kfree call.
Fixes: 093d24a204 ("arm64: PCI: Manage controller-specific data on per-controller basis")
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Timmy Li <lixiaoping3@huawei.com>
[lorenzo.pieralisi@arm.com: refactored code, rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: Will Deacon <will.deacon@arm.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.
Adjust the system_state check in smp_send_stop() to handle the extra states.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20170516184735.112589728@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, cpus_set_cap() calls static_branch_enable_cpuslocked(), which
must take the jump_label mutex.
We call cpus_set_cap() in the secondary bringup path, from the idle
thread where interrupts are disabled. Taking a mutex in this path "is a
NONO" regardless of whether it's contended, and something we must avoid.
We didn't spot this until recently, as ___might_sleep() won't warn for
this case until all CPUs have been brought up.
This patch avoids taking the mutex in the secondary bringup path. The
poking of static keys is deferred until enable_cpu_capabilities(), which
runs in a suitable context on the boot CPU. To account for the static
keys being set later, cpus_have_const_cap() is updated to use another
static key to check whether the const cap keys have been initialised,
falling back to the caps bitmap until this is the case.
This means that users of cpus_have_const_cap() gain should only gain a
single additional NOP in the fast path once the const caps are
initialised, but should always see the current cap value.
The hyp code should never dereference the caps array, since the caps are
initialized before we run the module initcall to initialise hyp. A check
is added to the hyp init code to document this requirement.
This change will sidestep a number of issues when the upcoming hotplug
locking rework is merged.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyniger <marc.zyngier@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
commit d98ecdaca2 ("arm64: perf: Count EL2 events if the kernel is
running in HYP") returns -EINVAL when perf system call perf_event_open is
called with exclude_hv != exclude_kernel. This change breaks applications
on VHE enabled ARMv8.1 platforms. The issue was observed with HHVM
application, which calls perf_event_open with exclude_hv = 1 and
exclude_kernel = 0.
There is no separate hypervisor privilege level when VHE is enabled, the
host kernel runs at EL2. So when VHE is enabled, we should ignore
exclude_hv from the application. This behaviour is consistent with PowerPC
where the exclude_hv is ignored when the hypervisor is not present and with
x86 where this flag is ignored.
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
[will: added comment to justify the behaviour of exclude_hv]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WZ6G
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
When CONFIG_ARM64_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Our compat swp emulation holds the compat user address in an unsigned
int, which it passes to __user_swpX_asm(). When a 32-bit value is passed
in a register, the upper 32 bits of the register are unknown, and we
must extend the value to 64 bits before we can use it as a base address.
This patch casts the address to unsigned long to ensure it has been
suitably extended, avoiding the potential issue, and silencing a related
warning from clang.
Fixes: bd35a4adc4 ("arm64: Port SWP/SWPB emulation support from arm")
Cc: <stable@vger.kernel.org> # 3.19.x-
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When handling a data abort from EL0, we currently zero the top byte of
the faulting address, as we assume the address is a TTBR0 address, which
may contain a non-zero address tag. However, the address may be a TTBR1
address, in which case we should not zero the top byte. This patch fixes
that. The effect is that the full TTBR1 address is passed to the task's
signal handler (or printed out in the kernel log).
When handling a data abort from EL1, we leave the faulting address
intact, as we assume it's either a TTBR1 address or a TTBR0 address with
tag 0x00. This is true as far as I'm aware, we don't seem to access a
tagged TTBR0 address anywhere in the kernel. Regardless, it's easy to
forget about address tags, and code added in the future may not always
remember to remove tags from addresses before accessing them. So add tag
handling to the EL1 data abort handler as well. This also makes it
consistent with the EL0 data abort handler.
Fixes: d50240a5f6 ("arm64: mm: permit use of tagged pointers at EL0")
Cc: <stable@vger.kernel.org> # 3.12.x-
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we take a watchpoint exception, the address that triggered the
watchpoint is found in FAR_EL1. We compare it to the address of each
configured watchpoint to see which one was hit.
The configured watchpoint addresses are untagged, while the address in
FAR_EL1 will have an address tag if the data access was done using a
tagged address. The tag needs to be removed to compare the address to
the watchpoints.
Currently we don't remove it, and as a result can report the wrong
watchpoint as being hit (specifically, always either the highest TTBR0
watchpoint or lowest TTBR1 watchpoint). This patch removes the tag.
Fixes: d50240a5f6 ("arm64: mm: permit use of tagged pointers at EL0")
Cc: <stable@vger.kernel.org> # 3.12.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we emulate userspace cache maintenance in the kernel, we can
currently send the task a SIGSEGV even though the maintenance was done
on a valid address. This happens if the address has a non-zero address
tag, and happens to not be mapped in.
When we get the address from a user register, we don't currently remove
the address tag before performing cache maintenance on it. If the
maintenance faults, we end up in either __do_page_fault, where find_vma
can't find the VMA if the address has a tag, or in do_translation_fault,
where the tagged address will appear to be above TASK_SIZE. In both
cases, the address is not mapped in, and the task is sent a SIGSEGV.
This patch removes the tag from the address before using it. With this
patch, the fault is handled correctly, the address gets mapped in, and
the cache maintenance succeeds.
As a second bug, if cache maintenance (correctly) fails on an invalid
tagged address, the address gets passed into arm64_notify_segfault,
where find_vma fails to find the VMA due to the tag, and the wrong
si_code may be sent as part of the siginfo_t of the segfault. With this
patch, the correct si_code is sent.
Fixes: 7dd01aef05 ("arm64: trap userspace "dc cvau" cache operation on errata-affected core")
Cc: <stable@vger.kernel.org> # 4.8.x-
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SDkm
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: Fix the DMA mmap and get_sgtable API with DMA_ATTR_FORCE_CONTIGUOUS
arm64: Print DT machine model in setup_machine_fdt()
arm64: pmu: Wire-up Cortex A53 L2 cache events and DTLB refills
arm64: module: split core and init PLT sections
arm64: pmuv3: handle pmuv3+
arm64: Add CNTFRQ_EL0 trap handler
arm64: Silence spurious kbuild warning on menuconfig
arm64: pmuv3: use arm_pmu ACPI framework
arm64: pmuv3: handle !PMUv3 when probing
drivers/perf: arm_pmu: add ACPI framework
arm64: add function to get a cpu's MADT GICC table
drivers/perf: arm_pmu: split out platform device probe logic
drivers/perf: arm_pmu: move irq request/free into probe
drivers/perf: arm_pmu: split cpu-local irq request/free
drivers/perf: arm_pmu: rename irq request/free functions
drivers/perf: arm_pmu: handle no platform_device
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
drivers/perf: arm_pmu: factor out pmu registration
drivers/perf: arm_pmu: fold init into alloc
drivers/perf: arm_pmu: define armpmu_init_fn
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- move BGRT handling to drivers/acpi so it can be shared between x86
and ARM
- bring the EFI stub's initrd and FDT allocation logic in line with
the latest changes to the arm64 boot protocol
- improvements and fixes to the EFI stub's command line parsing
routines
- randomize the virtual mapping of the UEFI runtime services on
ARM/arm64
- ... and other misc enhancements, cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: Don't use TASK_SIZE when randomizing the RT space
ef/libstub/arm/arm64: Randomize the base of the UEFI rt services region
efi/libstub/arm/arm64: Disable debug prints on 'quiet' cmdline arg
efi/libstub: Unify command line param parsing
efi/libstub: Fix harmless command line parsing bug
efi/arm32-stub: Allow boot-time allocations in the vmlinux region
x86/efi: Clean up a minor mistake in comment
efi/pstore: Return error code (if any) from efi_pstore_write()
efi/bgrt: Enable ACPI BGRT handling on arm64
x86/efi/bgrt: Move efi-bgrt handling out of arch/x86
efi/arm-stub: Round up FDT allocation to mapping size
efi/arm-stub: Correct FDT and initrd allocation rules for arm64
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
On arm32, the machine model specified in the device tree is printed
during boot-up, courtesy of of_flat_dt_match_machine().
On arm64, of_flat_dt_match_machine() is not called, and the machine
model information is not available from the kernel log.
Print the machine model to make it easier to derive the machine model
from an arbitrary kernel boot log.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add missing L2 cache events: read/write accesses and misses, as well as
the DTLB refills.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arm64 module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This leads to relocation failures if the distance between those
regions exceeds 128 MB. (In fact, this corner case is highly unlikely to
occur on arm64, but the issue has been observed on ARM, whose module
region is much smaller).
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section as the relocated branch instruction.
Since there may now be two PLT entries associated with each entry in
the symbol table, we can no longer hijack the symbol::st_size fields
to record the addresses of PLT entries as we emit them for zero-addend
relocations. So instead, perform an explicit comparison to check for
duplicate entries.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f1b36dcb5c ("arm64: pmuv3: handle !PMUv3 when probing") is
a little too restrictive, and prevents the use of of backwards
compatible PMUv3 extenstions, which have a PMUver value other than 1.
For instance, ARMv8.1 PMU extensions (as implemented by ThunderX2) are
reported with PMUver value 4.
Per the usual ID register principles, at least 0x1-0x7 imply a
PMUv3-compatible PMU. It's not currently clear whether 0x8-0xe imply the
same.
For the time being, treat the value as signed, and with 0x1-0x7 treated
as meaning PMUv3 is implemented. This may be relaxed by future patches.
Reported-by: Jayachandran C <jnair@caviumnetworks.com>
Tested-by: Jayachandran C <jnair@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We now trap accesses to CNTVCT_EL0 when the counter is broken
enough to require the kernel to mediate the access. But it
turns out that some existing userspace (such as OpenMPI) do
probe for the counter frequency, leading to an UNDEF exception
as CNTVCT_EL0 and CNTFRQ_EL0 share the same control bit.
The fix is to handle the exception the same way we do for CNTVCT_EL0.
Fixes: a86bd139f2 ("arm64: arch_timer: Enable CNTVCT_EL0 trap if workaround is enabled")
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we have a framework to handle the ACPI bits, make the PMUv3
code use this. The framework is a little different to what was
originally envisaged, and we can drop some unused support code in the
process of moving over to it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
[will: make armv8_pmu_driver_init static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
When probing via ACPI, we won't know up-front whether a CPU has a PMUv3
compatible PMU. Thus we need to consult ID registers during probe time.
This patch updates our PMUv3 probing code to test for the presence of
PMUv3 functionality before touching an PMUv3-specific registers, and
before updating the struct arm_pmu with PMUv3 data.
When a PMUv3-compatible PMU is not present, probing will return -ENODEV.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently the ACPI parking protocol code needs to parse each CPU's MADT
GICC table to extract the mailbox address and so on. Each time we parse
a GICC table, we call back to the parking protocol code to parse it.
This has been fine so far, but we're about to have more code that needs
to extract data from the GICC tables, and adding a callback for each
user is going to get unwieldy.
Instead, this patch ensures that we stash a copy of each CPU's GICC
table at boot time, such that anything needing to parse it can later
request it. This will allow for other parsers of GICC, and for
simplification to the ACPI parking protocol code. Note that we must
store a copy, rather than a pointer, since the core ACPI code
temporarily maps/unmaps tables while iterating over them.
Since we parse the MADT before we know how many CPUs we have (and hence
before we setup the percpu areas), we must use an NR_CPUS sized array.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We now return HVC_STUB_ERR when a stub hypercall fails, but we
leave whatever was in x0 on success. Zeroing it on return seems
like a good idea.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Nobody is using __hyp_get_vectors anymore, so let's remove both
implementations (hyp-stub and KVM).
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Let's define a new stub hypercall that resets the HYP configuration
to its default: hyp-stub vectors, and MMU disabled.
Of course, for the hyp-stub itself, this is a trivial no-op.
Hypervisors will have a bit more work to do.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Define a standard return value to be returned when a hyp stub
call fails, and make KVM use it for ARM_EXCEPTION_HYP_GONE
(instead of using a KVM-specific value).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The EL2 code is not corrupting lr anymore, so don't bother preserving
it in the EL1 trampoline code.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When entering the kernel hyp stub, we check whether or not we've
made it here through an HVC instruction, clobbering lr (aka x30)
in the process.
This is completely pointless, as HVC is the only way to get here
(all traps to EL2 are disabled, no interrupt override is applied).
So let's remove this bit of code whose only point is to corrupt
a valuable register.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
- Allow checking of a CPU-local erratum
- Add CNTVCT_EL0 trap handler
- Define Cortex-A73 MIDR
- Allow an erratum to be match for all revisions of a core
- Add capability to advertise Cortex-A73 erratum 858921
-----BEGIN PGP SIGNATURE-----
iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAljnlbgVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJECPQ0LrRPXpDx+YP/1OU8GnrVBR2cjEctaTz3s51sPRR
+7j1BZ3pbKnwY3XpM6GJpxc//sSBSphqWZXN5GJZW1lSgw7hpl02mA9rh62G4Xmh
wUqR2hmQ5UdenoR5tE39BZrzMFlef90bA7AZyatSqum6AEQcYPJZEgzOvEvfw/mY
Bc4w73At9OTILRXeZjJZabdeJ4aJLs+6xMfsc9ApgxiZIZ5xhJ7CQzcJFdQ2tFeB
9wYqxkt8i9aZfmj3IX14m3fXISQ4JlXoi8QTBqy7qunCMEFU6jtCwC5aZKj1U3Hh
zebVWomcWMQpFaJw3qxZgjVXftv5r2UsHbMoLo4wFa98Qerr7t9/bGifbFqpKm7S
hA0uzcftUHoQF+l/Qxt9rTlsPKrBMoXjY2XDkKiWP/hqXsXKDBnngKQb2ZFJFT5r
UABMBhqlBQpI2l0/Qn0fL7aEC1xZCVnSgGpAXFvg/Ci7X2K+HH37brt5uNh3vDZI
c5UaWUUycDa5GcCnmoK3QWVeitVW/ydJGaoIT06CKBDrktcpsoO4u4w6CI8xsIJL
RbJwCb72JU5HV7XDpdbc/lLzi30kWceOEUSHrs3dCEnkr41kOunDGm/Xxk/Sm8VL
SeYSx9UotuJvWWozZzVWpLiUSizjh6UB2XWnkSLkT++KA6YPX4L2/hYAw7E3bYVe
FAFoLL7jUYdrjpCF
=XSx4
-----END PGP SIGNATURE-----
Merge tag 'arch-timer-errata-prereq' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into for-next/core
Pre-requisites for the arch timer errata workarounds:
- Allow checking of a CPU-local erratum
- Add CNTVCT_EL0 trap handler
- Define Cortex-A73 MIDR
- Allow an erratum to be match for all revisions of a core
- Add capability to advertise Cortex-A73 erratum 858921
* tag 'arch-timer-errata-prereq' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms:
arm64: cpu_errata: Add capability to advertise Cortex-A73 erratum 858921
arm64: cpu_errata: Allow an erratum to be match for all revisions of a core
arm64: Define Cortex-A73 MIDR
arm64: Add CNTVCT_EL0 trap handler
arm64: Allow checking of a CPU-local erratum
In order to work around Cortex-A73 erratum 858921 in a subsequent
patch, add the required capability that advertise the erratum.
As the configuration option it depends on is not present yet,
this has no immediate effect.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some minor erratum may not be fixed in further revisions of a core,
leading to a situation where the workaround needs to be updated each
time an updated core is released.
Introduce a MIDR_ALL_VERSIONS match helper that will work for all
versions of that MIDR, once and for all.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since people seem to make a point in breaking the userspace visible
counter, we have no choice but to trap the access. Add the required
handler.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
this_cpu_has_cap() only checks the feature array, and not the errata
one. In order to be able to check for a CPU-local erratum, allow it
to inspect the latter as well.
This is consistent with cpus_have_cap()'s behaviour, which includes
errata already.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Arch-specific functions are added to allow for implementing a crash dump
file interface, /proc/vmcore, which can be viewed as a ELF file.
A user space tool, like kexec-tools, is responsible for allocating
a separate region for the core's ELF header within crash kdump kernel
memory and filling it in when executing kexec_load().
Then, its location will be advertised to crash dump kernel via a new
device-tree property, "linux,elfcorehdr", and crash dump kernel preserves
the region for later use with reserve_elfcorehdr() at boot time.
On crash dump kernel, /proc/vmcore will access the primary kernel's memory
with copy_oldmem_page(), which feeds the data page-by-page by ioremap'ing
it since it does not reside in linear mapping on crash dump kernel.
Meanwhile, elfcorehdr_read() is simple as the region is always mapped.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In addition to common VMCOREINFO's defined in
crash_save_vmcoreinfo_init(), we need to know, for crash utility,
- kimage_voffset
- PHYS_OFFSET
to examine the contents of a dump file (/proc/vmcore) correctly
due to the introduction of KASLR (CONFIG_RANDOMIZE_BASE) in v4.6.
- VA_BITS
is also required for makedumpfile command.
arch_crash_save_vmcoreinfo() appends them to the dump file.
More VMCOREINFO's may be added later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Primary kernel calls machine_crash_shutdown() to shut down non-boot cpus
and save registers' status in per-cpu ELF notes before starting crash
dump kernel. See kernel_kexec().
Even if not all secondary cpus have shut down, we do kdump anyway.
As we don't have to make non-boot(crashed) cpus offline (to preserve
correct status of cpus at crash dump) before shutting down, this patch
also adds a variant of smp_send_stop().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since arch_kexec_protect_crashkres() removes a mapping for crash dump
kernel image, the loaded data won't be preserved around hibernation.
In this patch, helper functions, crash_prepare_suspend()/
crash_post_resume(), are additionally called before/after hibernation so
that the relevant memory segments will be mapped again and preserved just
as the others are.
In addition, to minimize the size of hibernation image, crash_is_nosave()
is added to pfn_is_nosave() in order to recognize only the pages that hold
loaded crash dump kernel image as saveable. Hibernation excludes any pages
that are marked as Reserved and yet "nosave."
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arch_kexec_protect_crashkres() and arch_kexec_unprotect_crashkres()
are meant to be called by kexec_load() in order to protect the memory
allocated for crash dump kernel once the image is loaded.
The protection is implemented by unmapping the relevant segments in crash
dump kernel memory, rather than making it read-only as other archs do,
to prevent coherency issues due to potential cache aliasing (with
mismatched attributes).
Page-level mappings are consistently used here so that we can change
the attributes of segments in page granularity as well as shrink the region
also in page granularity through /sys/kernel/kexec_crash_size, putting
the freed memory back to buddy system.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
"crashkernel=" kernel parameter specifies the size (and optionally
the start address) of the system ram to be used by crash dump kernel.
reserve_crashkernel() will allocate and reserve that memory at boot time
of primary kernel.
The memory range will be exposed to userspace as a resource named
"Crash kernel" in /proc/iomem.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the ACPI BGRT handling code has been made generic, we can
enable it for arm64.
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
[ Updated commit log to reflect that BGRT is only enabled for arm64, and added
missing 'return' statement to the dummy acpi_parse_bgrt() function. ]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170404160245.27812-8-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To prevent unintended modifications to the kernel text (malicious or
otherwise) while running the EFI stub, describe the kernel image as
two separate sections: a .text section with read-execute permissions,
covering .text, .rodata and .init.text, and a .data section with
read-write permissions, covering .init.data, .data and .bss.
This relies on the firmware to actually take the section permission
flags into account, but this is something that is currently being
implemented in EDK2, which means we will likely start seeing it in
the wild between one and two years from now.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Replace open coded constants with symbolic ones throughout the
Image and the EFI headers. No binary level changes are intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The kernel's EFI PE/COFF header contains a dummy .reloc section, and
an explanatory comment that claims that this is required for the EFI
application loader to accept the Image as a relocatable image (i.e.,
one that can be loaded at any offset and fixed up in place)
This was inherited from the x86 implementation, which has elaborate host
tooling to mangle the PE/COFF header post-link time, and which populates
the .reloc section with a single dummy base relocation. On ARM, no such
tooling exists, and the .reloc section remains empty, and is never even
exposed via the BaseRelocationTable directory entry, which is where the
PE/COFF loader looks for it.
The PE/COFF spec is unclear about relocatable images that do not require
any fixups, but the EDK2 implementation, which is the de facto reference
for PE/COFF in the UEFI space, clearly does not care, and explicitly
mentions (in a comment) that relocatable images with no base relocations
are perfectly fine, as long as they don't have the RELOCS_STRIPPED
attribute set (which is not the case for our PE/COFF image)
So simply remove the .reloc section altogether.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Bring the PE/COFF header in line with the PE/COFF spec, by setting
NumberOfSymbols to 0, and removing the section alignment flags.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
After having split off the PE header, clean up the bits that remain:
use .long consistently, merge two adjacent #ifdef CONFIG_EFI blocks,
fix the offset of the PE header pointer and remove the redundant .align
that follows it.
Also, since we will be eliminating all open coded constants from the
EFI header in subsequent patches, let's replace the open coded "ARM\x64"
magic number with its .ascii equivalent.
No changes to the resulting binary image are intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation of yet another round of modifications to the PE/COFF
header, macroize it and move the definition into a separate source
file.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
read_system_reg() can readily be confused with read_sysreg(),
whereas these are really quite different in their meaning.
This patches attempts to reduce the ambiguity be reserving "sysreg"
for the actual system register accessors.
read_system_reg() is instead renamed to read_sanitised_ftr_reg(),
to make it more obvious that the Linux-defined sanitised feature
register cache is being accessed here, not the underlying
architectural system registers.
cpufeature.c's internal __raw_read_system_reg() function is renamed
in line with its actual purpose: a form of read_sysreg() that
indexes on (non-compiletime-constant) encoding rather than symbolic
register name.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 5c492c3f52 ("arm64: smp: Add function to determine if cpus are
stuck in the kernel") added a helper function to determine if die() is
supported in cpu_ops. This function assumes a cpu will have a valid
cpu_ops entry, but that may not be the case for cpu0 is spin-table or
parking protocol is used to boot secondary cpus. In that case, there
is a NULL dereference if have_cpu_die() is called by cpu0. So add a
check for a valid cpu_ops before dereferencing it.
Fixes: 5c492c3f52 ("arm64: smp: Add function to determine if cpus are stuck in the kernel")
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are two unnecessary newlines, one is in show_regs, another
is in __show_regs(), drop them.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To avoid having mappings that are writable and executable at the same
time, split the init region into a .init.text region that is mapped
read-only, and a .init.data region that is mapped non-executable.
This is possible now that the alternative patching occurs via the linear
mapping, and the linear alias of the init region is always mapped writable
(but never executable).
Since the alternatives descriptions themselves are read-only data, move
those into the .init.text region.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
One important rule of thumb when desiging a secure software system is
that memory should never be writable and executable at the same time.
We mostly adhere to this rule in the kernel, except at boot time, when
regions may be mapped RWX until after we are done applying alternatives
or making other one-off changes.
For the alternative patching, we can improve the situation by applying
the fixups via the linear mapping, which is never mapped with executable
permissions. So map the linear alias of .text with RW- permissions
initially, and remove the write permissions as soon as alternative
patching has completed.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We only need to initialise sctlr_el1 if we're installing an EL2 stub, so
we may as well defer this until we're doing so. Similarly, we can defer
intialising CPTR_EL2 until then, as we do not access any trapped
functionality as part of el2_setup.
This patch modified el2_setup accordingly, allowing us to remove a
branch and simplify the code flow.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The early el2_setup code is a little convoluted, with two branches where
one would do. This makes the code more painful to read than is
necessary.
We can remove a branch and simplify the logic by moving the early return
in the booted-at-EL1 case earlier in the function. This separates it
from all the setup logic that only makes sense for EL2.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv8.3 adds new instructions to support Release Consistent
processor consistent (RCpc) model, which is weaker than the
RCsc model.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM v8.3 adds support for new instructions to aid floating-point
multiplication and addition of complex numbers. Expose the support
via HWCAP and MRS emulation
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv8.3 adds support for a new instruction to perform conversion
from double precision floating point to integer to match the
architected behaviour of the equivalent Javascript conversion.
Expose the availability via HWCAP and MRS emulation.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for detecting VPIPT I-caches, as introduced by ARMv8.2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cachetype.h and cache.h are small and both obviously related to caches.
Merge them together to reduce clutter.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As a recent change to ARMv8, ASID-tagged VIVT I-caches are removed
retrospectively from the architecture. Consequently, we don't need to
support them in Linux either.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The CCSIDR_EL1.{NumSets,Associativity,LineSize} fields are only for use
in conjunction with set/way cache maintenance and are not guaranteed to
represent the actual microarchitectural features of a design.
The architecture explicitly states:
| You cannot make any inference about the actual sizes of caches based
| on these parameters.
Furthermore, CCSIDR_EL1.{WT,WB,RA,WA} have been removed retrospectively
from ARMv8 and are now considered to be UNKNOWN.
Since the kernel doesn't make use of set/way cache maintenance and it is
not possible for userspace to execute these instructions, we have no
need for the CCSIDR information in the kernel.
This patch removes the accessors, along with the related portions of the
cacheinfo support, which should instead be reintroduced when firmware has
a mechanism to provide us with reliable information.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The CCSIDR_EL1.{NumSets,Associativity,LineSize} fields are only for use
in conjunction with set/way cache maintenance and are not guaranteed to
represent the actual microarchitectural features of a design.
The architecture explicitly states:
| You cannot make any inference about the actual sizes of caches based
| on these parameters.
We currently use these fields to determine whether or the I-cache is
aliasing, which is bogus and known to break on some platforms. Instead,
assume the I-cache is always aliasing if it advertises a VIPT policy.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit af391b15f7 ("arm64: kernel: rename __cpu_suspend to keep it
aligned with arm") renamed cpu_suspend() to arm_cpuidle_suspend(), but
forgot to update the kerneldoc header.
Fixes: af391b15f7 ("arm64: kernel: rename __cpu_suspend to keep it aligned with arm")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit fc62d0207a ("kprobes: Introduce weak variant of
kprobe_exceptions_notify()") introduces a generic empty version of the
function for architectures that don't need special handling, like arm64.
As such, remove the arch/arm64/ specific handler.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Unlike most sysreg defintiions, the GICv3 definitions don't have a SYS_
prefix, and they don't live in <asm/sysreg.h>. Additionally, some
definitions are duplicated elsewhere (e.g. in the KVM save/restore
code).
For consistency, and to make it possible to share a common definition
for these sysregs, this patch moves the definitions to <asm/sysreg.h>,
adding a SYS_ prefix, and sorting the registers per their encoding.
Existing users of the definitions are fixed up so that this change is
not problematic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of including the full <linux/signal.h>, we are going to include the
types-only <linux/signal_types.h> header in <linux/sched.h>, to further
decouple the scheduler header from the signal headers.
This means that various files which relied on the full <linux/signal.h> need
to be updated to gain an explicit dependency on it.
Update the code that relies on sched.h's inclusion of the <linux/signal.h> header.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/hotplug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/hotplug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/topology.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
