Fix following warning:
aeroflex/greth.c:1326:11: warning: unused variable 'phy' [-Wunused-variable]
The variable was unused - remove it.
It looks like this warning has been there forever - was found by an
allyesconfig build of sparc32.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXNbEBAAoJEG4XJFUm622bKfAH/2CnQV7dBCT5QwEiKYoOdsCR
eTiH7OYjTPw/rjKaG3laFgFbecnfUnHoGt55WKqRY58JycLza+SPTTv57hFTnOl+
4kDhUEjUggxMs5BRb3H7wtcnQVs/pTkgqKqwUrmFNkG6idENQgorK6DG4SNCwIdf
JrmxiHcN73xSATxlduoA9bGpluW3OvnFfRrJfyT6UBWZaFqFe3qsoKDx08S2WU2z
kUI9ZUO9Ht7Q85QdLfPQI7xo54dXo9a+8v3yc7fNFbcu1s8cqeYuofXfypjK7H/B
DEY96mubDnmDt8YE8yR9wStVzTr5zf39urE3o+/xSKSKhQxmNo8+x2TBSm5nFSQ=
=0HKi
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation updates the mtu size and notify cdc_ncm
device using USB_CDC_SET_MAX_DATAGRAM_SIZE request about datagram
size change instead of changing rx_urb_size.
Whenever mtu is being changed, datagram size should also be
updated. Also updating maxmtu formula so it takes max_datagram_size with
use of cdc_ncm_max_dgram_size() and not ctx.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to check dev->reg_state against NETREG_REGISTERED after each
time we are woke up. But after commit 9e641bdcfa ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency"), it uses
skb_recv_datagram() which does not check dev->reg_state. This will
result if we delete a tun/tap device after a process is blocked in the
reading. The device will wait for the reference count which was held
by that process for ever.
Fixes this by using RCV_SHUTDOWN which will be checked during
sk_recv_datagram() before trying to wake up the process during uninit.
Fixes: 9e641bdcfa ("net-tun: restructure tun_do_read for better
sleep/wakeup efficiency")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xi Wang <xii@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da47b45720 ("phy: add support for a reset-gpio specification")
causes the following xtensa qemu crash according to Guenter Roeck:
[ 9.366256] libphy: ethoc-mdio: probed
[ 9.367389] (null): could not attach to PHY
[ 9.368555] (null): failed to probe MDIO bus
[ 9.371540] Unable to handle kernel paging request at virtual address 0000001c
[ 9.371540] pc = d0320926, ra = 903209d1
[ 9.375358] Oops: sig: 11 [#1]
This reverts commit da47b45720.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A domain with a frontend that does not implement a control ring has been
seen to cause a crash during domain save. This was apparently because
the call to xenvif_deinit_hash() in xenvif_disconnect_ctrl() is made
regardless of whether a control ring was connected, and hence
xenvif_hash_init() was called.
This patch brings the call to xenvif_deinit_hash() in
xenvif_disconnect_ctrl() inside the if clause that checks whether the
control ring event channel was connected. This is sufficient to ensure
it is only called if xenvif_init_hash() was called previously.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+Zv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Primary 4.7 merge window changes
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (148 commits)
IB/mlx5: Fire the CQ completion handler from tasklet
net/mlx5_core: Use tasklet for user-space CQ completion events
IB/core: Do not require CAP_NET_ADMIN for packet sniffing
IB/mlx4: Fix unaligned access in send_reply_to_slave
IB/mlx5: Report Scatter FCS device capability when supported
IB/mlx5: Add Scatter FCS support for Raw Packet QP
IB/core: Add Scatter FCS create flag
IB/core: Add Raw Scatter FCS device capability
IB/core: Add extended device capability flags
i40iw: pass hw_stats by reference rather than by value
i40iw: Remove unnecessary synchronize_irq() before free_irq()
i40iw: constify i40iw_vf_cqp_ops structure
IB/mlx5: Add UARs write-combining and non-cached mapping
IB/mlx5: Allow mapping the free running counter on PROT_EXEC
IB/mlx4: Use list_for_each_entry_safe
IB/SA: Use correct free function
IB/core: Fix a potential array overrun in CMA and SA agent
IB/core: Remove unnecessary check in ibnl_rcv_msg
IB/IWPM: Fix a potential skb leak
RDMA/nes: replace custom print_hex_dump()
...
Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my last commit I replaced MACSEC_SA_ATTR_KEYID by
MACSEC_SA_ATTR_KEY.
Fixes: 8acca6aceb ("macsec: key identifier is 128 bits, not 64")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length checks on the grant table copy_ops for setting hash key and
hash mapping are checking the local 'len' value which is correct in
the case of the former but not the latter. This was picked up by
static analysis checks.
This patch replaces checks of 'len' with 'copy_op.len' in both cases
to correct the incorrect check, keep the two checks consistent, and to
make it clear what the checks are for.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e7f4dc3536 ("mdio: Move allocation of interrupts into core"),
platforms which call fixed_phy_add() before fixed_mdio_bus_init() is
called (for example, because the platform code and the fixed_phy driver
use the same initcall level) crash in fixed_phy_add() since the
->mii_bus is not allocated.
Also since e7f4dc3536, these interrupts are initalized to polling by
default. The few (old) platforms which directly use fixed_phy_add()
from their platform code all pass PHY_POLL for the irq argument, so we
can keep these platforms not crashing by simply not attempting to set
the irq if PHY_POLL is passed.
Also, even if problems have not been reported on more modern platforms
which used fixed_phy_register() from drivers' probe functions, we return
-EPROBE_DEFER if the MDIO bus is not yet registered so that the probe is
retried later.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.
[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a patch to clean checkpatch warnings and errors
in the Space.c file.
Clean up the following warnings and errors.
WARNING :
* Block comments use * on subsequent lines
* Missing a blank line after declarations
* networking block comments don't use an empty /* line, use /*
* please, no space before tabs
* please, no spaces at the start of a line
* line over 80 characters
ERROR :
* code indent should use tabs where possible
* space prohibited after that open parenthesis '('
Signed-off-by: Amit Ghadge <amitg.b14@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(!count || count < 4) is always true.
So let's remove the coding which is dead at least since 2005.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
(a && a > 0) is equivalent to (a > 0).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only dereference variable self after checking it is not NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DEBUG is defined, a superfluous closing brace
is introduced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a412 ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function bgx_lmac_handler only use a member of
lmac after checking it is not null.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My laptop that uses the intel 7680 iwlwifi module would no longer
connects to the network. It would fail with a "Microcode SW error
detected." and spew out register state over and over again without ever
connecting to the network.
The cause is mis-merge in commit 909b27f706, where David seems to have
lost some of the changes to iwl_mvm_set_tx_cmd() from commit
5c08b0f502 ("iwlwifi: mvm: don't override the rate with the AMSDU
len").
The reason seems to be a conflict with commit d8fe484470 ("iwlwifi:
mvm: add support for new TX CMD API"), which touched a line adjacent to
the changes in 909b27f706.
David missed the fact that "info->driver_data[0]" had become
"skb_info->driver_data[0]". Then he removed the skb_info because it was
unused.
This just re-updates iwl_mvm_set_tx_cmd() with the lost two lines.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Reinoud Koornstra <reinoudkoornstra@gmail.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, we've fired all our completion callbacks straight from
our ISR.
Some of those callbacks were lightweight (for example, mlx5 Ethernet
napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over
those events could be so long, that we'll get into a hard lockup by
the system watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive
completion event to a per-EQ list and schedule a tasklet. In the
tasklet context we loop over all the CQs in the list and invoke the
user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
The current logic around the 'use_dac' module parameter prevents the
r81969 driver from being loadable on 64-bit systems without any RAM
below 4 GB when the parameter is left at its default value.
So introduce a new default value -1 which indicates that 64-bit DMA
should be enabled on sufficiently recent PCIe chips, i.e., versions
RTL_GIGA_MAC_VER_18 or later. Explicit param values of 0 or 1 retain
the existing behavior of unconditionally enabling/disabling 64-bit DMA
on 64-bit architectures (i.e., regardless of the type and version of the
chip)
Since PCIe chips do not need to CPlusCmd Dual Address Cycle to be set,
make that conditional on the device type as well.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you compile without OF_MDIO support in an RGMII configuration, we fail
to configure the dp83867 phy today by writing garbage into its configuration
registers.
On the other hand if you do compile with OF_MDIO and the phy gets loaded via
device tree, you have to have the properties set in the device tree, otherwise
we fail to load the driver and don't even attach the generic phy driver to
the interface anymore.
To make things slightly more consistent, make the rgmii configuration properties
optional and allow a user to omit them in their device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is configured as module, the #define for it really
is CONFIG_OF_MDIO_MODULE, not CONFIG_OF_MDIO. So if we are compiling it
as module, the dp83867 doesn't see that OF_MDIO was selected and doesn't
read the dt rgmii parameters.
The fix is simple: Use IS_ENABLED(). It checks for both - module as well
as compiled in code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ethernet devices, net_device.name will be eth%d before
register_netdev() is called. Don't print the net_device name until
the format string is replaced.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:
IP-Config: Reopening network devices...
genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be
IP-Config: Failed to open eth0
IP-Config: No network devices available
The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.
However, the real cause is that ravb_close() doesn't release any of the
R-Car Gen3-specific secondary IRQs.
Add the missing free_irq() calls to fix this.
Fixes: f51bdc236b ("ravb: Add dma queue interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-16
This series contains 2 fixes to ixgbe only.
Emil fixes transmit hangs when enabling SRIOV by swapping the parameters
in GENMASK in order to generate the correct mask.
Alex fixes his previous patch b83e30104b ("ixgbe/ixgbevf: Add support
for GSO partial") where he somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f748be531d ("stmmac: support new GMAC4") reverted a previous fix
by mistake. This commit re-applies said fix:
commit dec2165ff3
Author: Sonic Zhang <sonic.zhang@analog.com>
Date: Thu Jan 22 14:55:57 2015 +0800
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
Clear the TX COE bit when force_thresh_dma_mode is set even hardware
dma capability says support.
Tested on BF609.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on LPC4350 Hitex board.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like at some point I somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features. As a result the driver is now generating a warning about
vlan_features being setup incorrectly.
This patch corrects that by placing the update of netdev->features to
include the VLAN features so that it is after the point where we write
netdev->features into netdev->vlan_features.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap the parameters in GENMASK in order to generate the correct mask.
This change fixes Tx hangs when enabling SRIOV.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- MSR access API fixes and enhancements (Andy Lutomirski)
- early exception handling improvements (Andy Lutomirski)
- user-space FS/GS prctl usage fixes and improvements (Andy
Lutomirski)
- Remove the cpu_has_*() APIs and replace them with equivalents
(Borislav Petkov)
- task switch micro-optimization (Brian Gerst)
- 32-bit entry code simplification (Denys Vlasenko)
- enhance PAT handling in enumated CPUs (Toshi Kani)
... and lots of other cleanups/fixlets"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/arch_prctl/64: Restore accidentally removed put_cpu() in ARCH_SET_GS
x86/entry/32: Remove asmlinkage_protect()
x86/entry/32: Remove GET_THREAD_INFO() from entry code
x86/entry, sched/x86: Don't save/restore EFLAGS on task switch
x86/asm/entry/32: Simplify pushes of zeroed pt_regs->REGs
selftests/x86/ldt_gdt: Test set_thread_area() deletion of an active segment
x86/tls: Synchronize segment registers in set_thread_area()
x86/asm/64: Rename thread_struct's fs and gs to fsbase and gsbase
x86/arch_prctl/64: Remove FSBASE/GSBASE < 4G optimization
x86/segments/64: When load_gs_index fails, clear the base
x86/segments/64: When loadsegment(fs, ...) fails, clear the base
x86/asm: Make asm/alternative.h safe from assembly
x86/asm: Stop depending on ptrace.h in alternative.h
x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()
x86/asm: Make sure verify_cpu() has a good stack
x86/extable: Add a comment about early exception handlers
x86/msr: Set the return value to zero when native_rdmsr_safe() fails
x86/paravirt: Make "unsafe" MSR accesses unsafe even if PARAVIRT=y
x86/paravirt: Add paravirt_{read,write}_msr()
x86/msr: Carry on after a non-"safe" MSR access fails
...
VF's probe might log that it has no PM capability in its PCI configuration
space. As this is a valid configuration, silence such prints.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.
This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.
Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.
To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems like something broke in commit 1408cc1fa4 ("qed: Introduce VFs")
and the function no longer verifies that the vf is indeed a valid one.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent using uninitialized or negative index when handling
steering entries.
Fixes: b12d93d63c ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to specify the MAC address by 'mac-address' or
'local-mac-address' properties in the device tree. These are common
properties for the Ethernet controller.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This increases TX timeout period from one second to 5 seconds which is
the default value if the driver doesn't explicitly set
net_device->watchdog_timeo.
The one second timeout is too short for W5100 with SPI interface mode
which doesn't support burst READ/WRITE processing in the SPI transfer.
If the packet is transmitted while RX packets are being received at a
very high rate, the TX transmittion work in the workqueue is delayed
and the watchdog timer is expired.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
W5500 has different bit position for MAC filter in Socket n mode
register from W5100 and W5200.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is_w5200() function is not used anymore by the commit which adds
the W5500 support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function declares the 'err' local variable for no good reason, get rid
of it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both these functions declare the 'err' local variables for no good reason,
get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge code defers the switchdev port state setting, there
is no need to defer the port STP state change within the mv88e6xxx code.
Thus get rid of the driver's bridge work code.
This also fixes a race condition where the DSA layer assumes that the
bridge code already set the unbridged port's STP state to Disabled
before restoring the Forwarding state.
As a consequence, this also fixes the FDB flush for the unbridged port
which now correctly occurs during the Forwarding to Disabled transition.
Fixes: 0bc05d585d ("switchdev: allow caller to explicitly request attr_set as deferred")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One cpu can be processing packets which includes using the cached route
entries in the vrf device's private data and on another cpu the device
gets deleted which releases the routes and sets the pointers in net_vrf
to NULL. This results in datapath dereferencing a NULL pointer.
Fix by protecting access to dst's with rcu.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce support in updating statistics of offloaded TC flower
classifiers. Currently only the DROP action is supported.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue. query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.
The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since appropriate memory barriers are already there, use the relaxed
version to improve performance a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN-GPE, the interface is ARPHRD_NONE, thus we need to reset
mac_header after pulling the outer header.
v2: Put the code to the existing conditional block as suggested by
Shmulik Ladkani.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.
This patch adds code to xen-netback to use the value in a hash extra
info fragment passed from the guest frontend in a transmit-side
(i.e. netback receive side) packet to set the skb hash accordingly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.
This patch adds code to xen-netback to pass hash values calculated for
guest receive-side packets (i.e. netback transmit side) to the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.
A previous patch added the necessary boilerplate for mapping the control
ring from the frontend, should it be created. This patch adds
implementations for each of the defined protocol messages.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.
This patch adds the necessary code to xen-netback to map this new shared
ring, should it be created by a frontend, but does not add implementations
for any of the defined protocol messages. These are added in a subsequent
patch for clarity.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crash in netvsc_send() is observed when netvsc device is re-created on
mtu change/set channels. The crash is caused by dereferencing of NULL
channel pointer which comes from chn_table. The root cause is a mixture
of two facts:
- we set nvdev pointer in net_device_context in alloc_net_device()
before we populate chn_table.
- we populate chn_table[0] only.
The issue could be papered over by checking channel != NULL in
netvsc_send() but populating the whole chn_table and writing the
nvdev pointer afterwards seems more appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netvsc device is removed during mtu change or channels setup we get
into troubles as both paths are trying to remove the device. Synchronize
them with start_remove flag and rtnl lock.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify netvsvc pointer graph by getting rid of the redundant ndev
pointer. We can always get a pointer to struct net_device from somewhere
else.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the following structures keeping netvsc adapter state:
- struct net_device
- struct net_device_context
- struct netvsc_device
- struct rndis_device
- struct hv_device
and there are pointers/dependencies between them:
- struct net_device_context is contained in struct net_device
- struct hv_device has driver_data pointer which points to
'struct net_device' OR 'struct netvsc_device' depending on driver's
state (!).
- struct net_device_context has a pointer to 'struct hv_device'.
- struct netvsc_device has pointers to 'struct hv_device' and
'struct net_device_context'.
- struct rndis_device has a pointer to 'struct netvsc_device'.
Different functions get different structures as parameters and use these
pointers for traveling. The problem is (in addition to keeping in mind
this complex graph) that some of these structures (struct netvsc_device
and struct rndis_device) are being removed and re-created on mtu change
(as we implement it as re-creation of hyper-v device) so our travel using
these pointers is dangerous.
Simplify this to a the following:
- add struct netvsc_device pointer to struct net_device_context (which is
a part of struct net_device and thus never disappears)
- remove struct hv_device and struct net_device_context pointers from
struct netvsc_device
- replace pointer to 'struct netvsc_device' with pointer to
'struct net_device'.
- always keep 'struct net_device' in hv_device driver_data.
We'll end up with the following 'circular' structure:
net_device:
[net_device_context] -> netvsc_device -> rndis_device -> net_device
-> hv_device -> net_device
On MTU change we'll be removing the 'netvsc_device -> rndis_device'
branch and re-creating it making the synchronization easier.
There is one additional redundant pointer left, it is struct net_device
link in struct netvsc_device, it is going to be removed in a separate
commit.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netvsc_link_change() can race with netvsc_change_mtu() or
netvsc_set_channels() as these functions destroy struct netvsc_device and
rndis filter. Use start_remove flag for syncronization. As
netvsc_change_mtu()/netvsc_set_channels() are called with rtnl lock held
we need to take it before checking start_remove value in
netvsc_link_change().
Reported-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct netvsc_device is destroyed on mtu change so keeping the
protection flag there is not a good idea. Move it to struct
net_device_context which is preserved.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The framework only asserts (for now) that the reset gpio is not active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-14
This series contains updates to i40e and i40evf.
Kevin adds support to disable link on all ports and changes bits set
for telling firmware the PHY needs to be modified by the driver.
Anjali adds a feature to enable/disable all multicast for a trusted
VF. Added priv-flag knob to configure global true promiscuous
support.
Shannon adds the support code for calling the admin queue API call
aq_set_switch_config().
Mitch modifies the VF, to log a message if an untrusted VF attempts to
configure promiscuous mode, but lies to it and returns everything is ok
instead of returning an error. Corrects the logic for reporting the
receive packet hash. Fixed the adding of a broadcast filter for VFs,
since that all VSIs are configured to receive broadcasts as default,
so do not need to add a filter.
Catherine refactors the ethtool get_settings to report the possible
supported link modes from what we know about the current PHY type and
that with the firmware supported PHY types.
Jacob changes the driver to use WARN_ONCE in order to highlight the
issue, but do not display a warning every time when receive hang
message is received.
Akeem corrects receive ptype payload layer for non_tunneled IPv6, when
it should be layer 4 for UDP, instead of layer 3.
Dan Carpenter fixes an uninitialized variable bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The len value in the hwrm error message is wrong. Use the properly adjusted
value in the variable len.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
We removed this initialization but it is required. Let's put it back.
Fixes: 895106a577 ('i40e: trivial fixes')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.
Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.
Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).
Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects Rx ptype payload layer for non_tunneled ipv6. It
should be layer 4 for UDP, instead of layer 3.
Change-ID: I9382e4458ab3c4e58f6d2e9f195d5d4ee513805e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use WARN_ONCE in order to highlight the issue, but don't display
a warning every time. The user should be able to see the ethtool counter
we created if necessary to see how often it is occurring.
Change-ID: I40c4ea159819b64a7d33b7f5716749089791533a
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.
Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.
Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the support code for calling the AdminQ API call aq_set_switch_config
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables a feature to enable/disable all multicast
for a trusted VF.
Change-Id: I926eba7f8850c8d40f8ad7e08bbe4056bbd3985f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add flag to tell firmware to disable link on all ports.
This patch changes the bits set for telling firmware the PHY needs
to be modified by driver. Without this patch, the setting will only
set that mode for the current port on the device. Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.
Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes SG_RX_DV_GATE_REG_0_ADDR register offset
and ring state field lengths.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the race condition on updating the statistics
counters by moving the counters to the ring structure.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses ununiform latency across queues by adding
more queues to match with, upto number of CPU cores.
Also, number of interrupts are increased and the channel numbers
are reordered.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware doesn't allow sharing of interrupts,
this patch fixes the same by removing IRQF_SHARED flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the crash observed during IPv4 forward test by
setting the drop field in the dbptr.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FID value in a ULP_MEMIO command needs to be set to an IQ ID of
a queue configured for our PF. The FID/IQ id is used to index into the
PCIE FID table, to find out on which function the DMA needs to be
issued. Essentially, every DMA needs to have the ingress queue. The exact
ingress queue doesn't matter, but it needs to be an ingress queue
associated with the function you want to see the DMA on.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.
Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.
In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.
Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports. To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]
er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.
If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.
We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.
Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".
Before the patch, we could perform an *erroneous* correction:
Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.
Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.
Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.
For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.
e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.
Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Patch 562abd39 "xen-netback: support multiple extra info fragments
passed from frontend" contained a mistake which can result in an in-
correct number of responses being generated when handling errors
encountered when processing packets containing extra info fragments.
This patch fixes the problem.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to fix this before, but my previous fix was incomplete
and we can still get the same link error in randconfig builds
because of the way that Kconfig treats the
default y if MVNETA=y && MVNETA_BM_ENABLE
line that does not actually trigger when MVNETA_BM_ENABLE=m,
unlike I intended.
Changing the line to use MVNETA_BM_ENABLE!=n however has
the desired effect and hopefully makes all configurations
work as expected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 019ded3aa7 ("net: mvneta: bm: clarify dependencies")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a netns leak.
Fixes: 93edb8c7f9 ("gtp: reload GTPv1 header after pskb_may_pull()")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
