Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This traffic scheduler allows traffic classes states (transmission
allowed/not allowed, in the simplest case) to be scheduled, according
to a pre-generated time sequence. This is the basis of the IEEE
802.1Qbv specification.
Example configuration:
tc qdisc replace dev enp3s0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
base-time 1528743495910289987 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 300000 \
clockid CLOCK_TAI
The configuration format is similar to mqprio. The main difference is
the presence of a schedule, built by multiple "sched-entry"
definitions, each entry has the following format:
sched-entry <CMD> <GATE MASK> <INTERVAL>
The only supported <CMD> is "S", which means "SetGateStates",
following the IEEE 802.1Qbv-2015 definition (Table 8-6). <GATE MASK>
is a bitmask where each bit is a associated with a traffic class, so
bit 0 (the least significant bit) being "on" means that traffic class
0 is "active" for that schedule entry. <INTERVAL> is a time duration
in nanoseconds that specifies for how long that state defined by <CMD>
and <GATE MASK> should be held before moving to the next entry.
This schedule is circular, that is, after the last entry is executed
it starts from the first one, indefinitely.
The other parameters can be defined as follows:
- base-time: specifies the instant when the schedule starts, if
'base-time' is a time in the past, the schedule will start at
base-time + (N * cycle-time)
where N is the smallest integer so the resulting time is greater
than "now", and "cycle-time" is the sum of all the intervals of the
entries in the schedule;
- clockid: specifies the reference clock to be used;
The parameters should be similar to what the IEEE 802.1Q family of
specification defines.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skbprio (SKB Priority Queue) is a queueing discipline that prioritizes packets
according to their skb->priority field. Under congestion, already-enqueued lower
priority packets will be dropped to make space available for higher priority
packets. Skbprio was conceived as a solution for denial-of-service defenses that
need to route packets with different priorities as a means to overcome DoS
attacks.
v5
*Do not reference qdisc_dev(sch)->tx_queue_len for setting limit. Instead set
default sch->limit to 64.
v4
*Drop Documentation/networking/sch_skbprio.txt doc file to move it to tc man
page for Skbprio, in iproute2.
v3
*Drop max_limit parameter in struct skbprio_sched_data and instead use
sch->limit.
*Reference qdisc_dev(sch)->tx_queue_len only once, during initialisation for
qdisc (previously being referenced every time qdisc changes).
*Move qdisc's detailed description from in-code to Documentation/networking.
*When qdisc is saturated, enqueue incoming packet first before dequeueing
lowest priority packet in queue - improves usage of call stack registers.
*Introduce and use overlimit stat to keep track of number of dropped packets.
v2
*Use skb->priority field rather than DS field. Rename queueing discipline as
SKB Priority Queue (previously Gatekeeper Priority Queue).
*Queueing discipline is made classful to expose Skbprio's internal priority
queues.
Signed-off-by: Nishanth Devarajan <ndev2021@gmail.com>
Reviewed-by: Sachin Paryani <sachin.paryani@gmail.com>
Reviewed-by: Cody Doucette <doucette@bu.edu>
Reviewed-by: Michel Machado <michel@digirati.com.br>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove trailing whitespace and blank lines at EOF
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_cake targets the home router use case and is intended to squeeze the
most bandwidth and latency out of even the slowest ISP links and routers,
while presenting an API simple enough that even an ISP can configure it.
Example of use on a cable ISP uplink:
tc qdisc add dev eth0 cake bandwidth 20Mbit nat docsis ack-filter
To shape a cable download link (ifb and tc-mirred setup elided)
tc qdisc add dev ifb0 cake bandwidth 200mbit nat docsis ingress wash
CAKE is filled with:
* A hybrid Codel/Blue AQM algorithm, "Cobalt", tied to an FQ_Codel
derived Flow Queuing system, which autoconfigures based on the bandwidth.
* A novel "triple-isolate" mode (the default) which balances per-host
and per-flow FQ even through NAT.
* An deficit based shaper, that can also be used in an unlimited mode.
* 8 way set associative hashing to reduce flow collisions to a minimum.
* A reasonable interpretation of various diffserv latency/loss tradeoffs.
* Support for zeroing diffserv markings for entering and exiting traffic.
* Support for interacting well with Docsis 3.0 shaper framing.
* Extensive support for DSL framing types.
* Support for ack filtering.
* Extensive statistics for measuring, loss, ecn markings, latency
variation.
A paper describing the design of CAKE is available at
https://arxiv.org/abs/1804.07617, and will be published at the 2018 IEEE
International Symposium on Local and Metropolitan Area Networks (LANMAN).
This patch adds the base shaper and packet scheduler, while subsequent
commits add the optional (configurable) features. The full userspace API
and most data structures are included in this commit, but options not
understood in the base version will be ignored.
Various versions baking have been available as an out of tree build for
kernel versions going back to 3.10, as the embedded router world has been
running a few years behind mainline Linux. A stable version has been
generally available on lede-17.01 and later.
sch_cake replaces a combination of iptables, tc filter, htb and fq_codel
in the sqm-scripts, with sane defaults and vastly simpler configuration.
CAKE's principal author is Jonathan Morton, with contributions from
Kevin Darbyshire-Bryant, Toke Høiland-Jørgensen, Sebastian Moeller,
Ryan Mounce, Tony Ambardar, Dean Scarff, Nils Andreas Svee, Dave Täht,
and Loganaden Velvindron.
Testing from Pete Heist, Georgios Amanakis, and the many other members of
the cake@lists.bufferbloat.net mailing list.
tc -s qdisc show dev eth2
qdisc cake 8017: root refcnt 2 bandwidth 1Gbit diffserv3 triple-isolate split-gso rtt 100.0ms noatm overhead 38 mpu 84
Sent 51504294511 bytes 37724591 pkt (dropped 6, overlimits 64958695 requeues 12)
backlog 0b 0p requeues 12
memory used: 1053008b of 15140Kb
capacity estimate: 970Mbit
min/max network layer size: 28 / 1500
min/max overhead-adjusted size: 84 / 1538
average network hdr offset: 14
Bulk Best Effort Voice
thresh 62500Kbit 1Gbit 250Mbit
target 5.0ms 5.0ms 5.0ms
interval 100.0ms 100.0ms 100.0ms
pk_delay 5us 5us 6us
av_delay 3us 2us 2us
sp_delay 2us 1us 1us
backlog 0b 0b 0b
pkts 3164050 25030267 9530280
bytes 3227519915 35396974782 12879808898
way_inds 0 8 0
way_miss 21 366 25
way_cols 0 0 0
drops 5 0 1
marks 0 0 0
ack_drop 0 0 0
sp_flows 1 3 0
bk_flows 0 1 1
un_flows 0 0 0
max_len 68130 68130 68130
Tested-by: Pete Heist <peteheist@gmail.com>
Tested-by: Georgios Amanakis <gamanakis@gmail.com>
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETF (Earliest TxTime First) qdisc uses the information added
earlier in this series (the socket option SO_TXTIME and the new
role of sk_buff->tstamp) to schedule packets transmission based
on absolute time.
For some workloads, just bandwidth enforcement is not enough, and
precise control of the transmission of packets is necessary.
Example:
$ tc qdisc replace dev enp2s0 parent root handle 100 mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc add dev enp2s0 parent 100:1 etf delta 100000 \
clockid CLOCK_TAI
In this example, the Qdisc will provide SW best-effort for the control
of the transmission time to the network adapter, the time stamp in the
socket will be in reference to the clockid CLOCK_TAI and packets
will leave the qdisc "delta" (100000) nanoseconds before its transmission
time.
The ETF qdisc will buffer packets sorted by their txtime. It will drop
packets on enqueue() if their skbuff clockid does not match the clock
reference of the Qdisc. Moreover, on dequeue(), a packet will be dropped
if it expires while being enqueued.
The qdisc also supports the SO_TXTIME deadline mode. For this mode, it
will dequeue a packet as soon as possible and change the skb timestamp
to 'now' during etf_dequeue().
Note that both the qdisc's and the SO_TXTIME ABIs allow for a clockid
to be configured, but it's been decided that usage of CLOCK_TAI should
be enforced until we decide to allow for other clockids to be used.
The rationale here is that PTP times are usually in the TAI scale, thus
no other clocks should be necessary. For now, the qdisc will return
EINVAL if any clocks other than CLOCK_TAI are used.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a new tc ematch for using netfilter xtable matches.
This allows early classification as well as mirroning/redirecting traffic
based on logic implemented in netfilter extensions.
Current supported use case is classification based on the incoming IPSec
state used during decpsulation using the 'policy' iptables extension
(xt_policy).
The module dynamically fetches the netfilter match module and calls
it using a fake xt_action_param structure based on validated userspace
provided parameters.
As the xt_policy match does not access skb->data, no skb modifications
are needed on match.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blank help texts are probably either a typo, a Kconfig misunderstanding,
or some kind of half-committing to adding a help text (in which case a
TODO comment would be clearer, if the help text really can't be added
right away).
Best to remove them, IMO.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This queueing discipline implements the shaper algorithm defined by
the 802.1Q-2014 Section 8.6.8.2 and detailed in Annex L.
It's primary usage is to apply some bandwidth reservation to user
defined traffic classes, which are mapped to different queues via the
mqprio qdisc.
Only a simple software implementation is added for now.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Henrik Austad <henrik@austad.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It really makes no sense to have cls_act enabled without cls. In that
case, the cls_act code is dead. So select it.
This also fixes an issue recently reported by kbuild robot:
[linux-next:master 1326/4151] net/sched/act_api.c:37:18: error: implicit declaration of function 'tcf_chain_get'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: db50514f9a ("net: sched: add termination action to allow goto chain")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 3.12 it has been possible to configure the default queuing
discipline via sysctl. This patch adds ability to configure the
default queue discipline in kernel configuration. This is useful for
environments where configuring the value from userspace is difficult
to manage.
The default is still the same as before (pfifo_fast) and it is
possible to change after kernel init with sysctl. This is similar
to how TCP congestion control works.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the encode/decode functionality from the ife module instead of using
implementation inside the act_ife.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action allows the user to sample traffic matched by tc classifier.
The sampling consists of choosing packets randomly and sampling them using
the psample module. The user can configure the psample group number, the
sampling rate and the packet's truncation (to save kernel-user traffic).
Example:
To sample ingress traffic from interface eth1, one may use the commands:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff: \
matchall action sample rate 12 group 4
Where the first command adds an ingress qdisc and the second starts
sampling randomly with an average of one sampled packet per 12 packets on
dev eth1 to psample group 4.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LIBCRC32C is needed to compute crc32c on SCTP packets.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sample use case of how this is encoded:
user space via tuntap (or a connected VM/Machine/container)
encodes the tcindex TLV.
Sample use case of decoding:
IFE action decodes it and the skb->tc_index is then used to classify.
So something like this for encoded ICMP packets:
.. first decode then reclassify... skb->tcindex will be set
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xbeef \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
...next match the decode icmp packet...
sudo $TC filter add dev $ETH parent ffff: prio 4 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
... last classify it using the tcindex classifier and do someaction..
sudo $TC filter add dev $ETH parent ffff: prio 5 protocol ip \
handle 0x11 tcindex classid 1:1 \
action blah..
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe
to:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15
Also try to do a MAC address swap with pedit or worse
try to debug a policy with destination mac, source mac and
etherype. Then make few rules out of those and you'll get my point.
In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.
The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesnt get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac). And at times
when flipping back the packet a swap of the MAC addresses is needed.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.
The action will release the metadata created by the tunnel device
(decap), or set the metadata with the specified values for encap
operation.
For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:
$ tc filter add dev net0 protocol ip parent ffff: \
flower \
ip_proto 1 \
dst_ip 11.11.11.2 \
action tunnel_key set \
src_ip 11.11.0.1 \
dst_ip 11.11.0.2 \
id 11 \
action mirred egress redirect dev vxlan0
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The matchall classifier matches every packet and allows the user to apply
actions on it. This filter is very useful in usecases where every packet
should be matched, for example, packet mirroring (SPAN) can be setup very
easily using that filter.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb priority using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit prio 17 \
action ife encode \
allow prio \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb priority earlier. A zero skb priority will not be sent
Alternative hard code static priority of decimal 33 (unlike skbedit)
then mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use prio 33 \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit mark 17 \
action ife encode \
allow mark \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb mark earlier. A zero skb mark, when seen, will not be encoded.
Alternative hard code static mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.
Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.
YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress
xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok
xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0)
match 00000000/00000000 at 0 (success 0 )
action order 1: ife decode action reclassify
index 1 ref 1 bind 1 installed 14 sec used 14 sec
type: 0x0
Metadata: allow mark allow hash allow prio allow qmap
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules
YYYY: Lets show the sender side now ..
xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx: ethertype 0xdead
xxx: add skb->mark to whitelist of metadatum to send
xxx: rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15
xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 0 success 0)
match c0a87aed/ffffffff at 16 (success 0 )
match 00010000/00ff0000 at 8 (success 0 )
action order 1: skbedit mark 17
index 6 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 2: ife encode action pipe
index 3 ref 1 bind 1
dst MAC: 02:15:15:15:15:15 type: 0xDEAD
Metadata: allow mark
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
test by sending ping from sender to destination
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a generalization of the ingress qdisc as a qdisc holding
only classifiers. The clsact qdisc works on ingress, but also on egress.
In both cases, it's execution happens without taking the qdisc lock, and
the main difference for the egress part compared to prior version of [1]
is that this can be applied with _any_ underlying real egress qdisc (also
classless ones).
Besides solving the use-case of [1], that is, allowing for more programmability
on assigning skb->priority for the mqprio case that is supported by most
popular 10G+ NICs, it also opens up a lot more flexibility for other tc
applications. The main work on classification can already be done at clsact
egress time if the use-case allows and state stored for later retrieval
f.e. again in skb->priority with major/minors (which is checked by most
classful qdiscs before consulting tc_classify()) and/or in other skb fields
like skb->tc_index for some light-weight post-processing to get to the
eventual classid in case of a classful qdisc. Another use case is that
the clsact egress part allows to have a central egress counterpart to
the ingress classifiers, so that classifiers can easily share state (e.g.
in cls_bpf via eBPF maps) for ingress and egress.
Currently, default setups like mq + pfifo_fast would require for this to
use, for example, prio qdisc instead (to get a tc_classify() run) and to
duplicate the egress classifier for each queue. With clsact, it allows
for leaving the setup as is, it can additionally assign skb->priority to
put the skb in one of pfifo_fast's bands and it can share state with maps.
Moreover, we can access the skb's dst entry (f.e. to retrieve tclassid)
w/o the need to perform a skb_dst_force() to hold on to it any longer. In
lwt case, we can also use this facility to setup dst metadata via cls_bpf
(bpf_skb_set_tunnel_key()) without needing a real egress qdisc just for
that (case of IFF_NO_QUEUE devices, for example).
The realization can be done without any changes to the scheduler core
framework. All it takes is that we have two a-priori defined minors/child
classes, where we can mux between ingress and egress classifier list
(dev->ingress_cl_list and dev->egress_cl_list, latter stored close to
dev->_tx to avoid extra cacheline miss for moderate loads). The egress
part is a bit similar modelled to handle_ing() and patched to a noop in
case the functionality is not used. Both handlers are now called
sch_handle_ingress() and sch_handle_egress(), code sharing among the two
doesn't seem practical as there are various minor differences in both
paths, so that making them conditional in a single handler would rather
slow things down.
Full compatibility to ingress qdisc is provided as well. Since both
piggyback on TC_H_CLSACT, only one of them (ingress/clsact) can exist
per netdevice, and thus ingress qdisc specific behaviour can be retained
for user space. This means, either a user does 'tc qdisc add dev foo ingress'
and configures ingress qdisc as usual, or the 'tc qdisc add dev foo clsact'
alternative, where both, ingress and egress classifier can be configured
as in the below example. ingress qdisc supports attaching classifier to any
minor number whereas clsact has two fixed minors for muxing between the
lists, therefore to not break user space setups, they are better done as
two separate qdiscs.
I decided to extend the sch_ingress module with clsact functionality so
that commonly used code can be reused, the module is being aliased with
sch_clsact so that it can be auto-loaded properly. Alternative would have been
to add a flag when initializing ingress to alter its behaviour plus aliasing
to a different name (as it's more than just ingress). However, the first would
end up, based on the flag, choosing the new/old behaviour by calling different
function implementations to handle each anyway, the latter would require to
register ingress qdisc once again under different alias. So, this really begs
to provide a minimal, cleaner approach to have Qdisc_ops and Qdisc_class_ops
by its own that share callbacks used by both.
Example, adding qdisc:
# tc qdisc add dev foo clsact
# tc qdisc show dev foo
qdisc mq 0: root
qdisc pfifo_fast 0: parent :1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :4 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc clsact ffff: parent ffff:fff1
Adding filters (deleting, etc works analogous by specifying ingress/egress):
# tc filter add dev foo ingress bpf da obj bar.o sec ingress
# tc filter add dev foo egress bpf da obj bar.o sec egress
# tc filter show dev foo ingress
filter protocol all pref 49152 bpf
filter protocol all pref 49152 bpf handle 0x1 bar.o:[ingress] direct-action
# tc filter show dev foo egress
filter protocol all pref 49152 bpf
filter protocol all pref 49152 bpf handle 0x1 bar.o:[egress] direct-action
A 'tc filter show dev foo' or 'tc filter show dev foo parent ffff:' will
show an empty list for clsact. Either using the parent names (ingress/egress)
or specifying the full major/minor will then show the related filter lists.
Prior work on a mqprio prequeue() facility [1] was done mainly by John Fastabend.
[1] http://patchwork.ozlabs.org/patch/512949/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new config switch enables the ingress filtering infrastructure that is
controlled through the ingress_needed static key. This prepares the
introduction of the Netfilter ingress hook that resides under this unique
static key.
Note that CONFIG_SCH_INGRESS automatically selects this, that should be no
problem since this also depends on CONFIG_NET_CLS_ACT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a flow-based filter. So far, the very essential
packet fields are supported.
This patch is only the first step. There is a lot of potential performance
improvements possible to implement. Also a lot of features are missing
now. They will be addressed in follow-up patches.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450e1 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.
This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on NETFILTER is not sufficient to ensure the presence of the
'mark' field in nf_conn, also needs to depend on NF_CONNTRACK_MARK.
Fixes: 22a5dc ("net: sched: Introduce connmark action")
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tc action allows you to retrieve the connection tracking mark
This action has been used heavily by openwrt for a few years now.
There are known limitations currently:
doesn't work for initial packets, since we only query the ct table.
Fine given use case is for returning packets
no implicit defrag.
frags should be rare so fix later..
won't work for more complex tasks, e.g. lookup of other extensions
since we have no means to store results
we still have a 2nd lookup later on via normal conntrack path.
This shouldn't break anything though since skb->nfct isn't altered.
V2:
remove unnecessary braces (Jiri)
change the action identifier to 14 (Jiri)
Fix some stylistic issues caught by checkpatch
V3:
Move module params to bottom (Cong)
Get rid of tcf_hashinfo_init and friends and conform to newer API (Cong)
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action provides a possibility to exec custom BPF code.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Shewmaker <agshew@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tc action allows to work with vlan tagged skbs. Two supported
sub-actions are header pop and header push.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proportional Integral controller Enhanced (PIE) is a scheduler to address the
bufferbloat problem.
>From the IETF draft below:
" Bufferbloat is a phenomenon where excess buffers in the network cause high
latency and jitter. As more and more interactive applications (e.g. voice over
IP, real time video streaming and financial transactions) run in the Internet,
high latency and jitter degrade application performance. There is a pressing
need to design intelligent queue management schemes that can control latency and
jitter; and hence provide desirable quality of service to users.
We present here a lightweight design, PIE(Proportional Integral controller
Enhanced) that can effectively control the average queueing latency to a target
value. Simulation results, theoretical analysis and Linux testbed results have
shown that PIE can ensure low latency and achieve high link utilization under
various congestion situations. The design does not require per-packet
timestamp, so it incurs very small overhead and is simple enough to implement
in both hardware and software. "
Many thanks to Dave Taht for extensive feedback, reviews, testing and
suggestions. Thanks also to Stephen Hemminger and Eric Dumazet for reviews and
suggestions. Naeem Khademi and Dave Taht independently contributed to ECN
support.
For more information, please see technical paper about PIE in the IEEE
Conference on High Performance Switching and Routing 2013. A copy of the paper
can be found at ftp://ftpeng.cisco.com/pie/.
Please also refer to the IETF draft submission at
http://tools.ietf.org/html/draft-pan-tsvwg-pie-00
All relevant code, documents and test scripts and results can be found at
ftp://ftpeng.cisco.com/pie/.
For problems with the iproute2/tc or Linux kernel code, please contact Vijay
Subramanian (vijaynsu@cisco.com or subramanian.vijay@gmail.com) Mythili Prabhu
(mysuryan@cisco.com)
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Mythili Prabhu <mysuryan@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zefan Li requested [1] to perform the following cleanup/refactoring:
- Split cgroupfs classid handling into net core to better express a
possible more generic use.
- Disable module support for cgroupfs bits as the majority of other
cgroupfs subsystems do not have that, and seems to be not wished
from cgroup side. Zefan probably might want to follow-up for netprio
later on.
- By this, code can be further reduced which previously took care of
functionality built when compiled as module.
cgroupfs bits are being placed under net/core/netclassid_cgroup.c, so
that we are consistent with {netclassid,netprio}_cgroup naming that is
under net/core/ as suggested by Zefan.
No change in functionality, but only code refactoring that is being
done here.
[1] http://patchwork.ozlabs.org/patch/304825/
Suggested-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch implements the first size-based qdisc that attempts to
differentiate between small flows and heavy-hitters. The goal is to
catch the heavy-hitters and move them to a separate queue with less
priority so that bulk traffic does not affect the latency of critical
traffic. Currently "less priority" means less weight (2:1 in
particular) in a Weighted Deficit Round Robin (WDRR) scheduler.
In essence, this patch addresses the "delay-bloat" problem due to
bloated buffers. In some systems, large queues may be necessary for
obtaining CPU efficiency, or due to the presence of unresponsive
traffic like UDP, or just a large number of connections with each
having a small amount of outstanding traffic. In these circumstances,
HHF aims to reduce the HoL blocking for latency sensitive traffic,
while not impacting the queues built up by bulk traffic. HHF can also
be used in conjunction with other AQM mechanisms such as CoDel.
To capture heavy-hitters, we implement the "multi-stage filter" design
in the following paper:
C. Estan and G. Varghese, "New Directions in Traffic Measurement and
Accounting", in ACM SIGCOMM, 2002.
Some configurable qdisc settings through 'tc':
- hhf_reset_timeout: period to reset counter values in the multi-stage
filter (default 40ms)
- hhf_admit_bytes: threshold to classify heavy-hitters
(default 128KB)
- hhf_evict_timeout: threshold to evict idle heavy-hitters
(default 1s)
- hhf_non_hh_weight: Weighted Deficit Round Robin (WDRR) weight for
non-heavy-hitters (default 2)
- hh_flows_limit: max number of heavy-hitter flow entries
(default 2048)
Note that the ratio between hhf_admit_bytes and hhf_reset_timeout
reflects the bandwidth of heavy-hitters that we attempt to capture
(25Mbps with the above default settings).
The false negative rate (heavy-hitter flows getting away unclassified)
is zero by the design of the multi-stage filter algorithm.
With 100 heavy-hitter flows, using four hashes and 4000 counters yields
a false positive rate (non-heavy-hitters mistakenly classified as
heavy-hitters) of less than 1e-4.
Signed-off-by: Terry Lam <vtlam@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work contains a lightweight BPF-based traffic classifier that can
serve as a flexible alternative to ematch-based tree classification, i.e.
now that BPF filter engine can also be JITed in the kernel. Naturally, tc
actions and policies are supported as well with cls_bpf. Multiple BPF
programs/filter can be attached for a class, or they can just as well be
written within a single BPF program, that's really up to the user how he
wishes to run/optimize the code, e.g. also for inversion of verdicts etc.
The notion of a BPF program's return/exit codes is being kept as follows:
0: No match
-1: Select classid given in "tc filter ..." command
else: flowid, overwrite the default one
As a minimal usage example with iproute2, we use a 3 band prio root qdisc
on a router with sfq each as leave, and assign ssh and icmp bpf-based
filters to band 1, http traffic to band 2 and the rest to band 3. For the
first two bands we load the bytecode from a file, in the 2nd we load it
inline as an example:
echo 1 > /proc/sys/net/core/bpf_jit_enable
tc qdisc del dev em1 root
tc qdisc add dev em1 root handle 1: prio bands 3 priomap 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
tc qdisc add dev em1 parent 1:1 sfq perturb 16
tc qdisc add dev em1 parent 1:2 sfq perturb 16
tc qdisc add dev em1 parent 1:3 sfq perturb 16
tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/ssh.bpf flowid 1:1
tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/icmp.bpf flowid 1:1
tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/http.bpf flowid 1:2
tc filter add dev em1 parent 1: bpf run bytecode "`bpfc -f tc -i misc.ops`" flowid 1:3
BPF programs can be easily created and passed to tc, either as inline
'bytecode' or 'bytecode-file'. There are a couple of front-ends that can
compile opcodes, for example:
1) People familiar with tcpdump-like filters:
tcpdump -iem1 -ddd port 22 | tr '\n' ',' > /etc/tc/ssh.bpf
2) People that want to low-level program their filters or use BPF
extensions that lack support by libpcap's compiler:
bpfc -f tc -i ssh.ops > /etc/tc/ssh.bpf
ssh.ops example code:
ldh [12]
jne #0x800, drop
ldb [23]
jneq #6, drop
ldh [20]
jset #0x1fff, drop
ldxb 4 * ([14] & 0xf)
ldh [%x + 14]
jeq #0x16, pass
ldh [%x + 16]
jne #0x16, drop
pass: ret #-1
drop: ret #0
It was chosen to load bytecode into tc, since the reverse operation,
tc filter list dev em1, is then able to show the exact commands again.
Possible follow-up work could also include a small expression compiler
for iproute2. Tested with the help of bmon. This idea came up during
the Netfilter Workshop 2013 in Copenhagen. Also thanks to feedback from
Eric Dumazet!
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Uses perfect flow match (not stochastic hash like SFQ/FQ_codel)
- Uses the new_flow/old_flow separation from FQ_codel
- New flows get an initial credit allowing IW10 without added delay.
- Special FIFO queue for high prio packets (no need for PRIO + FQ)
- Uses a hash table of RB trees to locate the flows at enqueue() time
- Smart on demand gc (at enqueue() time, RB tree lookup evicts old
unused flows)
- Dynamic memory allocations.
- Designed to allow millions of concurrent flows per Qdisc.
- Small memory footprint : ~8K per Qdisc, and 104 bytes per flow.
- Single high resolution timer for throttled flows (if any).
- One RB tree to link throttled flows.
- Ability to have a max rate per flow. We might add a socket option
to add per socket limitation.
Attempts have been made to add TCP pacing in TCP stack, but this
seems to add complex code to an already complex stack.
TCP pacing is welcomed for flows having idle times, as the cwnd
permits TCP stack to queue a possibly large number of packets.
This removes the 'slow start after idle' choice, hitting badly
large BDP flows, and applications delivering chunks of data
as video streams.
Nicely spaced packets :
Here interface is 10Gbit, but flow bottleneck is ~20Mbit
cwin is big, yet FQ avoids the typical bursts generated by TCP
(as in netperf TCP_RR -- -r 100000,100000)
15:01:23.545279 IP A > B: . 78193:81089(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.545394 IP B > A: . ack 81089 win 3668 <nop,nop,timestamp 11597985 1115>
15:01:23.546488 IP A > B: . 81089:83985(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.546565 IP B > A: . ack 83985 win 3668 <nop,nop,timestamp 11597986 1115>
15:01:23.547713 IP A > B: . 83985:86881(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.547778 IP B > A: . ack 86881 win 3668 <nop,nop,timestamp 11597987 1115>
15:01:23.548911 IP A > B: . 86881:89777(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.548949 IP B > A: . ack 89777 win 3668 <nop,nop,timestamp 11597988 1115>
15:01:23.550116 IP A > B: . 89777:92673(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.550182 IP B > A: . ack 92673 win 3668 <nop,nop,timestamp 11597989 1115>
15:01:23.551333 IP A > B: . 92673:95569(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.551406 IP B > A: . ack 95569 win 3668 <nop,nop,timestamp 11597991 1115>
15:01:23.552539 IP A > B: . 95569:98465(2896) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.552576 IP B > A: . ack 98465 win 3668 <nop,nop,timestamp 11597992 1115>
15:01:23.553756 IP A > B: . 98465:99913(1448) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.554138 IP A > B: P 99913:100001(88) ack 65248 win 3125 <nop,nop,timestamp 1115 11597805>
15:01:23.554204 IP B > A: . ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.554234 IP B > A: . 65248:68144(2896) ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.555620 IP B > A: . 68144:71040(2896) ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.557005 IP B > A: . 71040:73936(2896) ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.558390 IP B > A: . 73936:76832(2896) ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.559773 IP B > A: . 76832:79728(2896) ack 100001 win 3668 <nop,nop,timestamp 11597993 1115>
15:01:23.561158 IP B > A: . 79728:82624(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.562543 IP B > A: . 82624:85520(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.563928 IP B > A: . 85520:88416(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.565313 IP B > A: . 88416:91312(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.566698 IP B > A: . 91312:94208(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.568083 IP B > A: . 94208:97104(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.569467 IP B > A: . 97104:100000(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.570852 IP B > A: . 100000:102896(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.572237 IP B > A: . 102896:105792(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.573639 IP B > A: . 105792:108688(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.575024 IP B > A: . 108688:111584(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.576408 IP B > A: . 111584:114480(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
15:01:23.577793 IP B > A: . 114480:117376(2896) ack 100001 win 3668 <nop,nop,timestamp 11597994 1115>
TCP timestamps show that most packets from B were queued in the same ms
timeframe (TSval 1159799{3,4}), but FQ managed to send them right
in time to avoid a big burst.
In slow start or steady state, very few packets are throttled [1]
FQ gets a bunch of tunables as :
limit : max number of packets on whole Qdisc (default 10000)
flow_limit : max number of packets per flow (default 100)
quantum : the credit per RR round (default is 2 MTU)
initial_quantum : initial credit for new flows (default is 10 MTU)
maxrate : max per flow rate (default : unlimited)
buckets : number of RB trees (default : 1024) in hash table.
(consumes 8 bytes per bucket)
[no]pacing : disable/enable pacing (default is enable)
All of them can be changed on a live qdisc.
$ tc qd add dev eth0 root fq help
Usage: ... fq [ limit PACKETS ] [ flow_limit PACKETS ]
[ quantum BYTES ] [ initial_quantum BYTES ]
[ maxrate RATE ] [ buckets NUMBER ]
[ [no]pacing ]
$ tc -s -d qd
qdisc fq 8002: dev eth0 root refcnt 32 limit 10000p flow_limit 100p buckets 256 quantum 3028 initial_quantum 15140
Sent 216532416 bytes 148395 pkt (dropped 0, overlimits 0 requeues 14)
backlog 0b 0p requeues 14
511 flows, 511 inactive, 0 throttled
110 gc, 0 highprio, 0 retrans, 1143 throttled, 0 flows_plimit
[1] Except if initial srtt is overestimated, as if using
cached srtt in tcp metrics. We'll provide a fix for this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it possible to build the CAN Identifier into the kernel, even
if the CAN support is build as a module.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can be used to match packets against netfilter ip sets created via ipset(8).
skb->sk_iif is used as 'incoming interface', skb->dev is 'outgoing interface'.
Since ipset is usually called from netfilter, the ematch
initializes a fake xt_action_param, pulls the ip header into the
linear area and also sets skb->data to the IP header (otherwise
matching Layer 4 set types doesn't work).
Tested-by: Mr Dash Four <mr.dash.four@googlemail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ematch makes it possible to classify CAN frames (AF_CAN) according
to their identifiers. This functionality can not be easily achieved with
existing classifiers, such as u32, because CAN identifier is always stored
in native endianness, whereas u32 expects Network byte order.
Signed-off-by: Rostislav Lisovy <lisovy@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
An implementation of CoDel AQM, from Kathleen Nichols and Van Jacobson.
http://queue.acm.org/detail.cfm?id=2209336
This AQM main input is no longer queue size in bytes or packets, but the
delay packets stay in (FIFO) queue.
As we don't have infinite memory, we still can drop packets in enqueue()
in case of massive load, but mean of CoDel is to drop packets in
dequeue(), using a control law based on two simple parameters :
target : target sojourn time (default 5ms)
interval : width of moving time window (default 100ms)
Based on initial work from Dave Taht.
Refactored to help future codel inclusion as a plugin for other linux
qdisc (FQ_CODEL, ...), like RED.
include/net/codel.h contains codel algorithm as close as possible than
Kathleen reference.
net/sched/sch_codel.c contains the linux qdisc specific glue.
Separate structures permit a memory efficient implementation of fq_codel
(to be sent as a separate work) : Each flow has its own struct
codel_vars.
timestamps are taken at enqueue() time with 1024 ns precision, allowing
a range of 2199 seconds in queue, and 100Gb links support. iproute2 uses
usec as base unit.
Selected packets are dropped, unless ECN is enabled and packets can get
ECN mark instead.
Tested from 2Mb to 10Gb speeds with no particular problems, on ixgbe and
tg3 drivers (BQL enabled).
Usage: tc qdisc ... codel [ limit PACKETS ] [ target TIME ]
[ interval TIME ] [ ecn ]
qdisc codel 10: parent 1:1 limit 2000p target 3.0ms interval 60.0ms ecn
Sent 13347099587 bytes 8815805 pkt (dropped 0, overlimits 0 requeues 0)
rate 202365Kbit 16708pps backlog 113550b 75p requeues 0
count 116 lastcount 98 ldelay 4.3ms dropping drop_next 816us
maxpacket 1514 ecn_mark 84399 drop_overlimit 0
CoDel must be seen as a base module, and should be used keeping in mind
there is still a FIFO queue. So a typical setup will probably need a
hierarchy of several qdiscs and packet classifiers to be able to meet
whatever constraints a user might have.
One possible example would be to use fq_codel, which combines Fair
Queueing and CoDel, in replacement of sfq / sfq_red.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qdisc supports two operations - plug and unplug. When the
qdisc receives a plug command via netlink request, packets arriving
henceforth are buffered until a corresponding unplug command is received.
Depending on the type of unplug command, the queue can be unplugged
indefinitely or selectively.
This qdisc can be used to implement output buffering, an essential
functionality required for consistent recovery in checkpoint based
fault-tolerance systems. Output buffering enables speculative execution
by allowing generated network traffic to be rolled back. It is used to
provide network protection for Xen Guests in the Remus high availability
project, available as part of Xen.
This module is generic enough to be used by any other system that wishes
to add speculative execution and output buffering to its applications.
This module was originally available in the linux 2.6.32 PV-OPS tree,
used as dom0 for Xen.
For more information, please refer to http://nss.cs.ubc.ca/remus/
and http://wiki.xensource.com/xenwiki/Remus
Changes in V3:
* Removed debug output (printk) on queue overflow
* Added TCQ_PLUG_RELEASE_INDEFINITE - that allows the user to
use this qdisc, for simple plug/unplug operations.
* Use of packet counts instead of pointers to keep track of
the buffers in the queue.
Signed-off-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Signed-off-by: Brendan Cully <brendan@cs.ubc.ca>
[author of the code in the linux 2.6.32 pvops tree]
Signed-off-by: David S. Miller <davem@davemloft.net>
IP_ROUTE_CLASSID depends on INET and NET_CLS_ROUTE4 selects
IP_ROUTE_CLASSID, but when INET is not enabled, this kconfig warning
is produced, so fix it by making NET_CLS_ROUTE4 depend on INET.
warning: (NET_CLS_ROUTE4) selects IP_ROUTE_CLASSID which has unmet direct dependencies (NET && INET)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of the Quick Fair Queue scheduler developed
by Fabio Checconi. The same algorithm is already implemented in ipfw
in FreeBSD. Fabio had an earlier version developed on Linux, I just
cleaned it up. Thanks to Eric Dumazet for testing this under load.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Stochastic Fair Blue scheduler, based on work from :
W. Feng, D. Kandlur, D. Saha, K. Shin. Blue: A New Class of Active Queue
Management Algorithms. U. Michigan CSE-TR-387-99, April 1999.
http://www.thefengs.com/wuchang/blue/CSE-TR-387-99.pdf
This implementation is based on work done by Juliusz Chroboczek
General SFB algorithm can be found in figure 14, page 15:
B[l][n] : L x N array of bins (L levels, N bins per level)
enqueue()
Calculate hash function values h{0}, h{1}, .. h{L-1}
Update bins at each level
for i = 0 to L - 1
if (B[i][h{i}].qlen > bin_size)
B[i][h{i}].p_mark += p_increment;
else if (B[i][h{i}].qlen == 0)
B[i][h{i}].p_mark -= p_decrement;
p_min = min(B[0][h{0}].p_mark ... B[L-1][h{L-1}].p_mark);
if (p_min == 1.0)
ratelimit();
else
mark/drop with probabilty p_min;
I did the adaptation of Juliusz code to meet current kernel standards,
and various changes to address previous comments :
http://thread.gmane.org/gmane.linux.network/90225http://thread.gmane.org/gmane.linux.network/90375
Default flow classifier is the rxhash introduced by RPS in 2.6.35, but
we can use an external flow classifier if wanted.
tc qdisc add dev $DEV parent 1:11 handle 11: \
est 0.5sec 2sec sfb limit 128
tc filter add dev $DEV protocol ip parent 11: handle 3 \
flow hash keys dst divisor 1024
Notes:
1) SFB default child qdisc is pfifo_fast. It can be changed by another
qdisc but a child qdisc MUST not drop a packet previously queued. This
is because SFB needs to handle a dequeued packet in order to maintain
its virtual queue states. pfifo_head_drop or CHOKe should not be used.
2) ECN is enabled by default, unlike RED/CHOKe/GRED
With help from Patrick McHardy & Andi Kleen
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Juliusz Chroboczek <Juliusz.Chroboczek@pps.jussieu.fr>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Andi Kleen <andi@firstfloor.org>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHOKe ("CHOose and Kill" or "CHOose and Keep") is an alternative
packet scheduler based on the Random Exponential Drop (RED) algorithm.
The core idea is:
For every packet arrival:
Calculate Qave
if (Qave < minth)
Queue the new packet
else
Select randomly a packet from the queue
if (both packets from same flow)
then Drop both the packets
else if (Qave > maxth)
Drop packet
else
Admit packet with proability p (same as RED)
See also:
Rong Pan, Balaji Prabhakar, Konstantinos Psounis, "CHOKe: a stateless active
queue management scheme for approximating fair bandwidth allocation",
Proceeding of INFOCOM'2000, March 2000.
Help from:
Eric Dumazet <eric.dumazet@gmail.com>
Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
