The mxs pinctrl driver will only support DT probe. That said, the mxs
device drivers can only get pinctrl state from pinctrl subsystem when
the drivers get probed from device tree.
Before converting the whole mxs platform support over to device tree,
we need to enable pinctrl dummy states for those non-DT board files
to ensure the pinctrl API adopted by mxs device drivers will work for
both DT and non-DT probe.
Instead of calling pinctrl_provide_dummies() directly in every board
file, the patch introduces soc specific calls mx23_soc_init() and
mx28_soc_init() for boards' .init_machine hook to invoke, so that
any soc specific setup for non-DT boot only can be added there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
This helps resolve the conflicts between the imx cleanups and the
new code that has gone into the imx tree.
Conflict resolution was originally done by Sascha Hauer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current code does not set the GPIO value to zero as mentioned in the comment.
Fix it by setting the initial GPIO value to zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301427910-31726-1-git-send-email-fabio.estevam@freescale.com
[ukleinek: squashed two patches together fixing both boards at once]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
