This patch along with my previous patch in mac80211 "Fix the
way ADDBA count..", fixes hang in tx when connected to an HT
AP which rejects/times out on addba req.
AGGR_ADDBA_PROGRESS should be cleared in aggr state when addba
negotiation is terminated due to either addba response is timed out
or addba is denied by the AP. With out clearing this bit,
all frames are queued onto s/w queue for getting tx'd as aggr and
will never be scheduled onto hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add automagic feature flags, so the firmware can tell the driver
about supported features and the driver can switch features on/off as
needed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The re-written rfkill core ensures rfkill devices are initialized to
the system default state. The core calls set_block after registration
so the driver shouldn't need to.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_set_global_sw_state() (previously rfkill_set_default()) will no
longer be exported by the rewritten rfkill core.
Instead, platform drivers which can provide persistent soft-rfkill state
across power-down/reboot should indicate their initial state by calling
rfkill_set_sw_state() before registration. Otherwise, they will be
initialized to a default value during registration by a set_block call.
We remove existing calls to rfkill_set_sw_state() which happen before
registration, since these had no effect in the old model. If these
drivers do have persistent state, the calls can be put back (subject
to testing :-). This affects hp-wmi and acer-wmi.
Drivers with persistent state will affect the global state only if
rfkill-input is enabled. This is required, otherwise booting with
wireless soft-blocked and pressing the wireless-toggle key once would
have no apparent effect. This special case will be removed in future
along with rfkill-input, in favour of a more flexible userspace daemon
(see Documentation/feature-removal-schedule.txt).
Now rfkill_global_states[n].def is only used to preserve global states
over EPO, it is renamed to ".sav".
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the rfkill conversion I added code to call
sony_nc_rfkill_set with the wrong argument, causing
a segfault Reinette reported. The compiler could not
catch that because the argument is, and needs to be,
void *.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ports the b43/legacy rfkill code to the new API offered
by cfg80211 and thus removes a lot of useless stuff.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces initial rfkill support for the ath5k driver
based on rfkill support in the cfg80211 framework.
All rfkill related code is separated into newly created rfkill.c.
Changes to existing code are minimal:
* added a new data structure ath5k_rfkill to the ath5k_softc structure
* inserted calls to HW rfkill init/deinit routines
* ath5k_intr() has been extended to handle AR5K_INT_GPIO interrupts
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a back-port from aggregation testing code.
In the past, we didn't limit the amount of active tx urbs.
However, ar9170 only has a limited buffer reserved for
pending data frames.
This wasn't much of a problem with the slower 802.11b/g.
We simply stopped the full queue and moved on to something different
in the mean time. But - as you guessed it - this simple approach
stands in way for a decent aggregation implementation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds new commands that the original firmware will not send
but we can use them to debug firmware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible unaligned u32 access in b43_generate_plcp_hdr().
Unaligned data is read/write with a u32 pointer instead of using the
packed structure. Some versions of gcc ignore the "packed" attribute, if the
structure element is accessed through a local pointer.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver used to be named rndis_wext before inclusion to upstream. Since
rndis_wlan is being converted to cfg80211, use of rndis_wext* names
can be confusing. So rename all rndis_wext to rndis_wlan (as should
have been when driver was renamed).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Capitalize enum labels as told in Documents/CodingStyle.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ports the iwlwifi rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff. The soft-
rfkill is completely removed since that is now handled by
setting the interfaces down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch turns on parallel scanning for the ata_piix driver.
This driver is used on most netbooks (no AHCI for cheap storage it seems).
The scan is the dominating time factor in the kernel boot for these
devices; with this flag it gets cut in half for the device I used
for testing (eeepc).
Alan took a look at the driver source and concluded that it ought to be safe
to do for this driver. Alan has also checked with the hardware team.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When I thought it was finally defeated, it came back with vengeance.
The failure cases are ever more convoluted. Now there is a single
combination which fails boot probing - MCP5x + Intel SSD and there are
two hotplug failure reports on different flavors where softreset fails
to bring up the device.
Through the many bug reports after the switch to hardreset, the
following patterns emerged.
- Softreset during boot always works.
- Hardreset during boot sometimes fails to bring up the link on
certain comibnations and device signature acquisition is unreliable.
- Hardreset is often necessary after hotplug.
It looks like the old behavior of preferring softreset was somehow
pretty close to the working reset protocol although it could have lost
a device during phy error handling by issuing hardreset.
This patch implements nv_hardreset() which kicks in only for post-boot
(!LOADING) device probing resets. This should be able to work around
all known problem cases. This isn't perfect but given the various
hardreset quirks on these controllers, I think this is as good as it
can get.
Tested on mcp5x (swncq), nf3 and ck804 for all both boot, warm and
hot probing cases.
Kudos to all the bug reporters and their painful hours with these damn
controllers. ;-)
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockr@shaw.ca>
Reported-by: David Lang <david@lang.hm>
Reported-by: Samo Vodopivec <lament.email.si@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Community reported one SB600 SATA issue(BZ #9412), which led to 64 bit
DMA disablement for all SB600 revisions by driver maintainers with
commits c7a42156d9 and
4cde32fc4b.
But the root cause is ASUS M2A-VM system BIOS bug in old revisions
like 0901, while forcing into 32bit DMA happens to work as workaround.
Now it's time to withdraw 4cde32fc4b
so as to restore the SB600 SATA 64bit DMA capability.
This patch is also adding the workaround for M2A-VM old BIOS revisions,
but users are suggested to upgrade their system BIOS to the latest one
if they meet this issue.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Delete Makefile. It is only used for out-of-tree compilation
and was never needed. It slipped in by mistake.
* Remove from Kbuild all the out of tree stuff as promised.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libosd has it's own sense decoding and printout. Don't
let scsi_lib duplicate that printout. (Which is done wrong
in regard to osd commands)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch was inspired by Al Viro, for simplifying and fixing the
retrieval of osd-devices by in-kernel users, eg: file systems.
In-Kernel users, now, go through the same path user-mode does by
opening a file on the osd char-device and though holding a reference
to both the device and the Module.
A file pointer was added to the osd_dev structure which is now
allocated for each user. The internal osd_dev is no longer exposed
outside of the uld. I wanted to do that for a long time so each
libosd user can have his own defaults on the device.
The API is left the same, so user code need not change.
It is no longer needed to open/close a file handle on the osd
char-device from user-mode, before mounting an exofs on it.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libosd users that need to work with bios, must sometime use
the request_queue associated with the osd_dev. Make a wrapper for
that, and convert all in-tree users.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For supporting of chained-bios we can not inspect the first
bio only, as before. Caller shall pass the total length of the
request, ie. sum_bytes(bio-chain).
Also since the bio might be a chain we don't set it's direction
on behalf of it's callers. The bio direction should be properly
set prior to this call. So fix a couple of write users that now
need to set the bio direction properly
[In this patch I change both library code and user sites at
exofs, to make it easy on integration. It should be submitted
via James's scsi-misc tree.]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
_osd_req_finalize_data_integrity was trying to deduce the number of
out_bytes from passed osd_request->out.bio. This is wrong when
the bio is chained. The caller of _osd_req_finalize_data_integrity
has more ready available information and should just pass it.
Also in the light of future support for CDB-continuation segment this is
a better solution.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
By popular demand, define usefull wrappers for osd_req_read/write
that recieve kernel pointers. All users had their own.
Also remove these from exofs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shorten out the Attributes names.
Align all results on column 24.
Print system ID in a new line.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PowerMac bootup with CONFIG_IDE=y oopses in ide_pio_cycle_time():
because "ide: try to use PIO Mode 0 during probe if possible" causes
pmac_ide_set_pio_mode() to be called before drive->id has been set.
Bart points out other places which now need drive->id set earlier,
so follow his advice to allocate it in ide_port_alloc_devices()
(using kzalloc_node, without error message, as when allocating drive)
and memset it for reuse in ide_port_init_devices_data().
Fixed in passing: ide_host_alloc() was missing ide_port_free_devices()
from an error path.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Combined mode pci quirk hacks went away - so the table to keep in sync
no longer exists.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can't do this for the later ones as they have all sorts of magic boot
time stuff that needs reviewing and the like. However we can do it for the
older ones and it turns out we need to as some IBM docking stations have a
second PIIX series device in them and without this change you can't use it
very well
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make the following EM related cleanups.
* Use msleep(1) instead of udelay(100) and reduce retry count to 5.
* s/MAX_SLOTS/EM_MAX_SLOTS/, s/MAX_RETRY/EM_MAX_RETRY/
* Make EM constants enums as suggested by Jeff.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We very rarely (if ever) complete more than one command in the
sactive mask at the time, even for extremely high IO rates. So
looping over the entire range of possible tags is pointless,
instead use __ffs() to just find the completed tags directly.
Updated to clear the tag from the done_mask instead of shifting
done_mask down as suggested by From: Tejun Heo <htejun@gmail.com>
Verified with a user space tester to produce the same results.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
32-bit PIO seems to work fine on sata_sil hardware (tested on SiI3114) and is
listed as OK in the Silicon Image datasheets. Enable it.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ECC initialization takes too long. It writes zeroes by portions
of 4 byte, it takes more than 6 minutes on my machine to initialize
512Mb ECC DIMM module. Change portion to 128Kb - it significantly
reduces initialization time.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Handling of the trailing byte in ata_sff_data_xfer() is suboptimal bacause:
- it always initializes the padding buffer to 0 which is not really needed in
both the read and write cases;
- it has to use memcpy() to transfer a single byte from/to the padding buffer;
- it uses io{read|write}16() accessors which swap bytes on the big endian CPUs
and so have to additionally convert the data from/to the little endian format
instead of using io{read|write}16_rep() accessors which are not supposed to
change the byte ordering.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prevent EDAC compilation units from being built by default and let the
user explicitly select the needed modules.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
While at it, fix a link failure when !K8_NB.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Also, link into Kbuild by adding Kconfig and Makefile entries.
Borislav:
- Kconfig/Makefile splitting
- use zero-sized arrays for the sysfs attrs if not enabled
- rename sysfs attrs to more conform values
- shorten CONFIG_ names
- make multiple structure members assignment vertically aligned
- fix/cleanup comments
- fix function return value patterns
- fix err labels
- fix a memleak bug caught by Ingo
- remove the NUMA dependency and use num_k8_northbrides for initializing
a driver instance per NB.
- do not copy the pvt contents into the mci struct in
amd64_init_2nd_stage() and save it in the mci->pvt_info void ptr
instead.
- cleanup debug calls
- simplify amd64_setup_pci_device()
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- convert to the new {rd|wr}msr_on_cpus interfaces.
- convert pvt->old_mcgctl to a bitmask thus saving some bytes
- fix/cleanup comments
- fix function return value patterns
- add a proper bugfix found by Doug to amd64_check_ecc_enabled where we
missed checking for the ECC enabled bit in NB CFG.
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- compute dct_sel_base_off in f10_match_to_this_node() correctly since
it cannot be assumed that the Reserved bits are zero and they have to be
masked out instead.
- cleanup, remove StinkyIdentifiers, simplify logic
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- fix a wrong negation in f10_determine_base_addr_offset()
- fix a wrong mask in f10_determine_base_addr_offset() which should
select DctSelBaseAddr[31:11] and not [31:16] as it was before
- remove StinkyIdentifiers, trivially simplify code.
- fix/cleanup comments
- fix function return value patterns
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
Fail f10_early_channel_count() if error encountered while reading a NB
register since those cached register contents are accessed afterwards.
- fix/cleanup comments
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- rename sysfs attrs to more conform names
- cleanup/fix comments according to BKDG text
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is for dumping different registers and testing the address mapping
logic using the ECC syndromes.
Borislav:
- split sysfs attrs per file
- use more conform names for the sysfs attrs
- fix function return value patterns
- cleanup/fix comments
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Bluetooth version of Apple Mighty mouse (0x05ac/0x030c) doesn't, according to
multiple reports on linux-input@, need the same quirk as the USB version of
this mouse (0x05ac/0x0304) does.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to "Documentation/printk-formats.txt", if the type is
dependent on a config option for its size, like resource_size_t,
we should use a format specifier of its largest possible type and
explicitly cast to it.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support only PCIe NIC functions zero and one, and FCoE
functions as 3 and 4. Future configurations can mix these up in any
fashion.
This patch removes the 0-1 dependancy and allows usage of any of the 4
functions. We also find the alternate NIC function (if exist) and
determine our port number based on the comparison of the two functions:
Lower function number gets first port, higher function gets second port.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract either manufacturer or Bladecenter Open Fabric
Manager (BOFM) MAC address. BOFM may indicate an
alternate MAC address. This patch honors that request
by extracting the MAC address from a different
flash location if a flag is set.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max frame size register is set higher than the MTU to
accomodate FCoE frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not necessary if hardware supports 65536 as it's the default setting.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps with bad latencies for large reads from /dev/zero, but might
conceivably break some application that "knows" that a read of /dev/zero
cannot return early. So do this early in the merge window to give us
maximal test coverage, even if the patch is totally trivial.
Obviously, no well-behaved application should ever depend on the read
being uninterruptible, but hey, bugs happen.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the doc book in the previous patches had incorrect multi-line short
function descriptors. Fixed it all to be the correct single line descriptor.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware is able to handle Broadcast primitives, but upstream driver does not
have support for broadcast primitive handling. Now this patch is mainly to
support broadcast primitives.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FW will report Queue full event to Driver and driver will handle this queue
full event to SCSI Mid layer.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1. Handle integrated Raid device(Add/Delete) and error condition and check
related to Raid device. is_logical_volume will represent logical volume
device.
2. Raid device dual port support is added. Main functions to support this
feature are mpt_raid_phys_disk_get_num_paths and mpt_raid_phys_disk_pg1.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Resending patch considering Grants G's code review.
Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) SAS topology Rescan is added. If Firmware is doing Reset and we get
Device add interrupt from Firmware, we will not receive it as part of Reset
is going ON. After Reset we will do special Rescan of SAS topology.
2.) Driver version changed from 3.04.08 to 3.04.09.
Added proper lock/unlock in mptsas_not_responding_devices() as per James'
comment.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SAS topology scan is restructured. HBA firmware is generating more
events. Expander Events are added, Link status events are also added with
respect to SAS topology scan optimization.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now Firmware events are handled by firmware event queue.
Previously it was handled in interrupt context/WorkQueue of Linux.
Firmware Event handling is restructured and optimized.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) rewrite of ioctl_cmds internal generated function that issue commands to
firmware, porting them to be single threaded using the generic MPT_MGMT
struct. All wait Queues are replace by completion Queue.
2) added seperate callback handler for ioctl task managment
(mptctl_taskmgmt_reply), to handle command that timeout
3) rewrite mptctl_bus_reset
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
_MPT_SCSI_HOST struct.
2.) Reset from Scsi mid layer and internal Reset are seperate context.
Adding DeviceResetCtx for internal Device reset frame.
mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) Previously we had mutliple #defines to use same values.
Now those #defines are optimized.
MPT_IOCTL_STATUS_* is removed and MPT_MGMT_STATUS_* are new
#defines.
2.) config path is optimized.
Instead of wait Queue and timer, using completion Q.
3.) mpt_timer_expired is not used.
[jejb: elide patch to eliminate mpt_timer_expired]
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SendEventNotification was handled through FIFO, now it is using doorbell to
communicate with hardware. Added Sleep Flag as an extra argument to support
Can-Sleep feature. Resending patch including compilation error fix reviewed
by Grant Grundler.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sas_discovery_quiesce_io flag is used to control IO start/resume functionality.
IO will be stoped while doing discovery of topology. Once discovery is completed
It will resume IO. Resending patch including James review.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.
The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions. So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.
The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
then they need to be remapped as discussed below.
1) Set the Local Address bit in the SGE Flags field.
MPI_SGE_FLAGS_LOCAL_ADDRESS
2) Ensure we are using 64-bit SGEs
3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
location is Host Memory.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the DRM-driven DPMS code, encoders are considered idle unless a
connector is hooked to them, so mode setting is skipped. This makes load
detection fail as none of the hardware is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To differentiate between encountering an out-of-memory error with running
out of space in the aperture, use ENOSPC for the later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ensure that the drm_vblank_pre_modeset() is always balanced by
drm_vblank_post_modeset() within intel_crtc_mode_set().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The batch buffer may be shared with another read buffer, so we should not
ignore any previously set domains, but just or in the command domain (and
check that the buffer is not writable).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
By sending a broken execbuffer (its length was not suitably aligned) I
triggered an operation upon a freed object. The invalid alignment was
discovered after updating the write_domain on the object but before the
object was placed on the active queue. So during the unwind process
following the error, the now freed object attempts to flush its
non-existent, but outstanding, GPU writes causing this use-after-free.
[drm:i915_dispatch_gem_execbuffer] *ERROR* alignment
[drm:i915_gem_execbuffer] *ERROR* dispatch failed -22
WARNING: at lib/kref.c:43 warn_slowpath_null+0x10/0x15()
Modules linked in:
Pid: 4552, comm: lt-csi-drm Not tainted 2.6.30-rc6 #423
Call Trace:
[<c0119ef3>] warn_slowpath_fmt+0x57/0x6d
[<c014de24>] ? get_pageblock_migratetype+0x18/0x1e
[<c014e8fd>] ? free_hot_page+0xa/0xc
[<c014e915>] ? __free_pages+0x16/0x1f
[<c0153ebf>] ? shmem_truncate_range+0x63e/0x656
[<c015fb2f>] ? slob_page_alloc+0x146/0x1c8
[<c0119f19>] warn_slowpath_null+0x10/0x15
[<c01f55f2>] kref_get+0x1b/0x21
[<c02605db>] i915_gem_object_move_to_active+0x1f/0x56
[<c0261302>] i915_add_request+0x156/0x19a
[<c026136e>] i915_gem_object_flush_gpu_write_domain+0x28/0x3f
[<c0261eca>] i915_gem_object_unbind+0x4a/0x124
[<c0261fd7>] i915_gem_free_object+0x33/0x9b
[<c0250d6b>] drm_gem_object_free+0x28/0x4a
[<c0250d43>] ? drm_gem_object_free+0x0/0x4a
[<c01f55ce>] kref_put+0x38/0x41
[<c0250cbf>] drm_gem_object_unreference+0x11/0x13
[<c0250d06>] drm_gem_object_handle_unreference+0x1e/0x21
[<c0250d13>] drm_gem_object_release_handle+0xa/0xe
[<c01f3e6b>] idr_for_each+0x5f/0x98
[<c0250d09>] ? drm_gem_object_release_handle+0x0/0xe
[<c0250daf>] drm_gem_release+0x22/0x34
[<c025046f>] drm_release+0x1e8/0x3c4
[<c0162d25>] __fput+0xaf/0x146
[<c0162dce>] fput+0x12/0x14
[<c01605ef>] filp_close+0x48/0x52
[<c011b182>] put_files_struct+0x57/0x9b
[<c011b1e4>] exit_files+0x1e/0x20
[<c011c6b6>] do_exit+0x16d/0x511
[<c03704ab>] ? __schedule+0x3d4/0x3e5
[<c0103f0d>] ? handle_irq+0xd/0x69
[<c011caa7>] do_group_exit+0x4d/0x73
[<c011cae0>] sys_exit_group+0x13/0x17
[<c010268c>] sysenter_do_call+0x12/0x2b
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Using the new PNP resource checking code, this patch allows the i915
driver to allocate MCHBAR space if needed and use the BAR to determine
current memory settings.
[apw@canonical.com: moved to the new generic PNP resource interface]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
failure to update-index after git-am --reject to hand-apply
Signed-off-by: Eric Anholt <eric@anholt.net>
TRACE_EVENT is a more generic way to define tracepoints. Doing so adds
these new capabilities to this tracepoint:
- zero-copy and per-cpu splice() tracing
- binary tracing without printf overhead
- structured logging records exposed under /debug/tracing/events
- trace events embedded in function tracer output and other plugins
- user-defined, per tracepoint filter expressions
...
Cons:
- no dev_t info for the output of plug, unplug_timer and unplug_io events.
no dev_t info for getrq and sleeprq events if bio == NULL.
no dev_t info for rq_abort,...,rq_requeue events if rq->rq_disk == NULL.
This is mainly because we can't get the deivce from a request queue.
But this may change in the future.
- A packet command is converted to a string in TP_assign, not TP_print.
While blktrace do the convertion just before output.
Since pc requests should be rather rare, this is not a big issue.
- In blktrace, an event can have 2 different print formats, but a TRACE_EVENT
has a unique format, which means we have some unused data in a trace entry.
The overhead is minimized by using __dynamic_array() instead of __array().
I've benchmarked the ioctl blktrace vs the splice based TRACE_EVENT tracing:
dd dd + ioctl blktrace dd + TRACE_EVENT (splice)
1 7.36s, 42.7 MB/s 7.50s, 42.0 MB/s 7.41s, 42.5 MB/s
2 7.43s, 42.3 MB/s 7.48s, 42.1 MB/s 7.43s, 42.4 MB/s
3 7.38s, 42.6 MB/s 7.45s, 42.2 MB/s 7.41s, 42.5 MB/s
So the overhead of tracing is very small, and no regression when using
those trace events vs blktrace.
And the binary output of TRACE_EVENT is much smaller than blktrace:
# ls -l -h
-rw-r--r-- 1 root root 8.8M 06-09 13:24 sda.blktrace.0
-rw-r--r-- 1 root root 195K 06-09 13:24 sda.blktrace.1
-rw-r--r-- 1 root root 2.7M 06-09 13:25 trace_splice.out
Following are some comparisons between TRACE_EVENT and blktrace:
plug:
kjournald-480 [000] 303.084981: block_plug: [kjournald]
kjournald-480 [000] 303.084981: 8,0 P N [kjournald]
unplug_io:
kblockd/0-118 [000] 300.052973: block_unplug_io: [kblockd/0] 1
kblockd/0-118 [000] 300.052974: 8,0 U N [kblockd/0] 1
remap:
kjournald-480 [000] 303.085042: block_remap: 8,0 W 102736992 + 8 <- (8,8) 33384
kjournald-480 [000] 303.085043: 8,0 A W 102736992 + 8 <- (8,8) 33384
bio_backmerge:
kjournald-480 [000] 303.085086: block_bio_backmerge: 8,0 W 102737032 + 8 [kjournald]
kjournald-480 [000] 303.085086: 8,0 M W 102737032 + 8 [kjournald]
getrq:
kjournald-480 [000] 303.084974: block_getrq: 8,0 W 102736984 + 8 [kjournald]
kjournald-480 [000] 303.084975: 8,0 G W 102736984 + 8 [kjournald]
bash-2066 [001] 1072.953770: 8,0 G N [bash]
bash-2066 [001] 1072.953773: block_getrq: 0,0 N 0 + 0 [bash]
rq_complete:
konsole-2065 [001] 300.053184: block_rq_complete: 8,0 W () 103669040 + 16 [0]
konsole-2065 [001] 300.053191: 8,0 C W 103669040 + 16 [0]
ksoftirqd/1-7 [001] 1072.953811: 8,0 C N (5a 00 08 00 00 00 00 00 24 00) [0]
ksoftirqd/1-7 [001] 1072.953813: block_rq_complete: 0,0 N (5a 00 08 00 00 00 00 00 24 00) 0 + 0 [0]
rq_insert:
kjournald-480 [000] 303.084985: block_rq_insert: 8,0 W 0 () 102736984 + 8 [kjournald]
kjournald-480 [000] 303.084986: 8,0 I W 102736984 + 8 [kjournald]
Changelog from v2 -> v3:
- use the newly introduced __dynamic_array().
Changelog from v1 -> v2:
- use __string() instead of __array() to minimize the memory required
to store hex dump of rq->cmd().
- support large pc requests.
- add missing blk_fill_rwbs_rq() in block_rq_requeue TRACE_EVENT.
- some cleanups.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A2DF669.5070905@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
cls_cgroup: Fix oops when user send improperly 'tc filter add' request
r8169: fix crash when large packets are received
* 'for-linus' of git://neil.brown.name/md:
md/raid5: fix bug in reshape code when chunk_size decreases.
md/raid5 - avoid deadlocks in get_active_stripe during reshape
md/raid5: use conf->raid_disks in preference to mddev->raid_disk
New iSCSI driver for Broadcom BNX2 devices. The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The CNIC driver controls BNX2 hardware rings and resources used by
iSCSI. Most hardware resources for iSCSI are separate from those
used for ethernet networking.
iSCSI uses a separate MAC address and IP address. The CNIC driver
creates a UIO interface to handle the non-offloaded packets such as
ARP, etc in userspace.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add interface and functions to support a new CNIC driver to drive
the Broadcom bnx2 hardware for iSCSI offload.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add ISCSI_NETLINK messages for iSCSI NICs to get information such as
path from userspace. Original iscsid messages are now always sent as
multicast to group 1. The new messages are sent to group 2.
The multicast changes were made by Mike Christie.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already. Avoid surprises when MAXSMP is enabled.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch extracts the opaque data from pci i/o
region 0 via the added VIRTIO_BLK_F_IDENTIFY
field. By convention this data takes the form of
that returned by an ATA IDENTIFY DEVICE command,
however the driver (except for structure size)
makes no interpretation of the data. The structure
data is copied wholesale to userspace via a
HDIO_GET_IDENTITY ioctl command (eg: hdparm -i <dev>).
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There is no need to check if a pointer is NULL before calling
vfree(), since vfree() function already check for it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool is a standard way of getting information about
ethernet interfaces. We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.
Signed-off-by: Chaitanya Lala <clala@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten. It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit. This kernel patch takes the latter
option.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fakehard is a really simple driver implementing only necessary
callbacks and serves the role of an example of driver for HardMAC
IEEE 802.15.4 device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not indicate support for frag lists.
Furthermore, even if it did, the code is walking the frag
lists incorrectly. The idiom is:
for (iter = skb_shinfo(skb)->frag_list; iter; iter = iter->next)
but it's doing:
for (iter = skb_shinfo(skb)->frag_list; iter;
iter = skb_shinfo(iter)->frag_list)
which would never work. And this proves that this driver never
saw an SKB with active frag lists.
So just remove the code altogether and the driver TX path becomes
much simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.
Signed-off-by: NeilBrown <neilb@suse.de>
md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts. This is used to achieve a
stable state before making internal changes.
Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.
It is not necessary to inhibit reshape IO when a quiesce is
requested. Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.
So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.
This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported. So this patch is
not needed in earlier kernels.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->raid_disks can be changed and any time by a request from
user-space. It is a suggestion as to what number of raid_disks is
desired.
conf->raid_disks can only be changed by the raid5 module with suitable
locks in place. It is a statement as to the current number of
raid_disks.
There are two places where the latter should be used, but the former
is used. This can lead to a crash when reshaping an array.
This patch changes to mddev-> to conf->
Signed-off-by: NeilBrown <neilb@suse.de>
Make SCSI reset error handler decode unit attention ASC
and after a target reset wait for a unit attention that indicates
a reset occurred rather than just for any old unit attention.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that the cciss SCSI error handling routines operate with interrupts
enabled, we no longer need to maintain the list of command completions that
sendcmd() might inadvertantly scoop up, since now it only runs at driver init
time, and there won't be any other commands for it to scoop up. So we
can remove that list and the code that adds to it and processes it.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Change cciss scsi error handling routines to work with interrupts enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Separate the error processing from sendcmd_withirq_core from the code
which retries commands. The rationale for this is that the SCSI error
handling code can then be made to use sendcmd_withirq_core, but avoid
retrying commands.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out code to process target status of completed commands in sendcmd()
and sendcmd_withirq_core(), and fix problem that bad target status was ignored in
sendcmd_withirq_core.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Simplify interfaces of sendcmd() and sendcmd_withirq() so that they
provide only one way to address commands instead of three ways.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor the core of sendcmd_withirq out to provide a simpler interface
which provides access to full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use schedule_timeout_uninterruptible instead of schedule_timeout in the
scsi error handling code when waiting between TUR polls since we are not
interested in nor want to be interrupted by signals.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add support to ibmvscsi for the capabilities MAD. This command gets sent
to the Virtual I/O server prior to login in order to communicate client
capabilities. Additionally it returns information regarding capabilities
that the server supports. The two main capabilities communicated in this
MAD are related to partition migration and client reserve. Client reserve
allows for SCSI-2 reservations to be sent to virtual disks which are backed
by physical LUNs and will result in the reservation being sent to the
physical LUN.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A new mode of error reporting, fast fail, has been added to the VIOS
which allows failover to happen more quickly.
If this new fast fail mode is enabled on the VIOS and the vSCSI client
supports the mode, the VIOS will not return MEDIUM error on path failures,
but rather return VIOSRP_ADAPTER_FAIL in the crq response, which
ibmvscsi will translate to DID_ERROR.
This new mode can be enabled for single path configurations as well,
so it is the new default error reporting mode. A module parameter is
provided to disable this new behavior on the off chance it causes a
problem on some old VIOS version.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi driver currently sends the SRP Login before sending the Adapter
Info MAD, which can result in commands getting sent to the virtual adapter
before we are ready for them. This results in a slight window where the target
devices may not behave as expected. Change the order and close the window.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Previously we had one timeout that was used for all types of operations.
This adds specific timeout values for different operations (init, login,
adapter info MAD, abort task, and LUN reset).
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for 16 byte CDBs to the ibmvscsi driver.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In ide_probe_port() skip probe if ide_port_wait_ready() returns -ENODEV
and print error message instead of debug one if it returns -EBUSY.
v2:
Fix the default 'rc' value.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ensure MPS remains in synchronization across all NIC/FCoE
functions after a reset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Queued work processing will now be serialized with its own
lower-priority spinlock. This also simplifies the work-queue
interface for future work-queue consumers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As firmware will ultimately terminate (stop) and port
states-cleared.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ISP24xx and above must query the host-status register, not HCCR.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ISP24xx and above ISPs perform a RISC reset in
qla24xx_reset_chip(), which is called prior to
qla24xx_chip_diag().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With RSCN states not being kept across qla2x00_configure_loop()
invocations, loop-resync distruptions during fabric-discovery may
cause ports to remain in a lost state. Force state
renegotiation during a follow-on configure-loop iteration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Unlike earlier ISPs, recent ISPs (ISP81xx) can in fact fail this
mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes a NULL pointer bug that occurs when IO is being
carried out on a vport for which the cpu affinity mode is turned on.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SCSI-midlayer's fast-fail codes consider an DID_ERROR status
as a driver-error and the failed I/O would then be retried in the
midlayer without being fast-failed to dm-multipath. DID_BUS_BUSY
status returns would induce unneeded path-failures events being
propagated to the DM/MD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is not required as VLAN header is added by device
interface driver, this was causing bad FC_CRC in FCoE pkts when
using VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removes periodic fcoe_watchdog timer used across all fcoe interface
maintained in fcoe_hostlist instead added new fcoe_queue_timer
per fcoe interface.
Added timer is armed only when some pending skb need to be flushed
as oppose to periodic 1 second fcoe_watchdog, since now
fcoe_queue_timer is used on demand thus set this to 2 jiffies.
Now fcoe_queue_timer is much simple than fcoe_watchdog using lock to
process all fcoe interface from fcoe_hostlist.
I noticed +ve performance result with using 2 jiffies timer as
this helps flushing fcoe_pending_queue quickly.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently fcoe_pending_queue.lock held twice for every new skb
adding to this queue when already least one pkt is pending in this
queue and that is not uncommon once skb pkts starts getting queued
here upon fcoe_start_io => dev_queue_xmit failure.
This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue
function, this new logic grabs fcoe_pending_queue.lock only once to
add a new skb instead twice as used to be.
I think after this patch call flow around fcoe_check_wait_queue
calling in fcoe_xmit is bit simplified with modified
fcoe_check_wait_queue function taking care of adding and
removing pending skb in one function.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a sequence is received in response to an exchange we issued previously,
we should check to see if the exchange has completed. If yes, the sequence
should be discarded. Since the exchange might be still in the completion
process, it should be untouched.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we aborted a command, because it timed out we should not use
DID_ABORT. It will fail the command right away back to the upper
layer. We want to use something that indicated that the problem
did not complete normally, but it was not a fatal problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FIP frames should leave the fcoe layer with skb->protocol set to
ETH_P_FIP, not ETH_P_802_3.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a reset is sent using fcoeadm on a non-FIP mode NIC,
there's no link flap, so the fcoe_ctlr stays in non-FIP mode.
In that case, FIP wasn't setting the flogi_oxid or map_dest flag,
causing the FLOGI to be sent with the both wrong source MAC and
the wrong destination MAC address, causing it to fail.
This leads to a non-functioning HBA until a link flap or
instance delete/create.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver needs dst_cache->dev so it should include net/dst.h
to ensure that it builds. While net/tcp.h probably includes it
already, we shouldn't rely on that since there is no guarantee
that this won't change in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There are several scenarios where the ibmvfc driver needs to
try to log back into a target on the fabric. Today when these events
occur, we simply go through re-discovery for all attached targets,
assuming that either the query of the name server or an ADISC will
indicate we might need to log back into the target, which doesn't
work for all scenarios. Fix this by taking note of the affected target(s)
in these conditions and ensuring we try to PLOGI back into the target.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For certain scenarios during device rediscovery, we detect we need
to log back into a target. Currently we do just that - PLOGI/PRLI
back into the target. Change the code to delete and add the target
from the FC transport layer as well, to ensure we handle any cases
where the target may have changed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The virtual I/O server controlling the NPIV adapter associated with
a virtual fibre channel adapter can send a HALT event to the client.
When this occurs, the client can no longer send commands until a RESUME
is received. By adding support for flush on halt, we will get all of
our outstanding commands flushed back before the Virtual I/O server
enters the halt state, eliminating potential command timeouts for
outstanding commands which might occur if we did not support this feature.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for a new command supported by the Virtual I/O
Server, NPIV Logout. The command will abort all outstanding commands
and log out of the fabric. Currently, the only way to do this is
by breaking the CRQ, which can take a fairly long time when lots of
commands are outstanding. The NPIV Logout commands provides a mechanism
to accomplish virtually the same function, but is much faster.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver currently logs errors during discovery for several
transient fabric errors, which generally get retried. If retries
do not work, we see multiple errors in the log. If retries do work,
we see errors in the log which may be confusing since the retry worked.
This patch enhances the discovery time error logging to only log errors
for command failures during discovery if all allowed retries have been
used up. The existing behavior of logging all failures can be restored
by setting the hosts log_level to a value of 3 or greater.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use DEVICE_ATTR macro for defining device sysfs attributes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since target allocations can occur while resetting the virtual adapter,
we shouldn't be using GFP_KERNEL for them as it could hang. Switch to
use GFP_NOIO.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix an obvious bug in processing error responses for SCSI commands
which can result in successful responses being incorrectly returned
with DID_ERROR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The async split up of probing in sd.c created a potential failure case where
something goes wrong with device_add(), but which we don't recover properly.
Since, in general, asynchronous error handling is hard, move the device_add()
into the asynchronous path (it should be fast) and make sure all the deferred
processing cannot fail.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Documentation is incorrect (we removed some functions referred to), and
none of the bug warnings now apply. Additionally remove the spurious check on
the return from blk_get_request() which can't fail if __GFP_WAIT is passed in.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Kirkwood architecture uses the same watchdog device as the Orion
architecture. This patch adds orion5x_wdt as a platform device for
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The name of the define for the Reset-Out-Mask register as well as its
bit for the watchdog reset are changed to match the names used for
Kirkwood (which in turn match the processor specification more
closely). There is no functional change.
This patch prepares for adding orion5x_wdt as a platform device to
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add support for persistent vport definitions at creation at boot time
Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for the new queues in the SLI-4 interface. There are :
- Work Queues - host-to-adapter for fast-path traffic
- Mailbox Queues - host-to-adapter for control (slow-path)
- Buffer Queues - host-to-adapter for posting buffers for async receive
- Completion Queues - adapter-to-host for posting async events,
completions for fast or slow patch work, receipt of async
receive traffic
- Event Queues - tied to MSI-X vectors, binds completion queues with
interrupts
These patches add the all the support code to tie into command submission
and response paths, updates the interrupt handling, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Outline udelay and fix a few issues.
MIPS: ioctl.h: Fix headers_check warnings
MIPS: Cobalt: PCI bus is always required to obtain the board ID
MIPS: Kconfig: Remove "Support for" from Cavium system type
MIPS: Sibyte: Honor CONFIG_CMDLINE
SSB: BCM47xx: Export ssb_watchdog_timer_set
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The previous patch submission had a I typo I didn't catch but Bartlomiej
noted. Guess this proves the point about any patch being risky late in an rc
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this patch export ssb_watchdog_timer_set to allow to use it in a Linux
watchdog driver.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
[ARM] pxa: fix pxa27x_udc default pullup GPIO
[ARM] pxa/imote2: fix UCAM sensor board ADC model number
mx[23]: don't put clock lookups in __initdata
fix oops when using console=ttymxcN with N > 0
[ARM] ARMv7 errata: only apply fixes when running on applicable CPU
[ARM] 5534/1: kmalloc must return a cache line aligned buffer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci-of: Fix the wrong accessor to HOSTVER register
mvsdio: fix config failure with some high speed SDHC cards
mvsdio: ignore high speed timing requests from the core
mmc/omap: Use disable_irq_nosync() from within irq handlers.
sdhci-of: Add fsl,esdhc as a valid compatible to bind against
mvsdio: allow automatic loading when modular
mxcmmc: Fix missing return value checking in DMA setup code.
mxcmmc : Reset the SDHC hardware if software timeout occurs.
omap_hsmmc: Trivial fix for a typo in comment
mxcmmc: decrease minimum frequency to make MMC cards work
The virtual driver implements fasync and ioctl support, but it is not used
and unneeded due to its constraints via the Bluetooth core layer. So too
just make the driver simpler, remove support for both of them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BKL push down added some BKL into the open callback of the virtual
driver. The driver is really simple and need no such locking and so just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The virtual driver still uses a home grown way of waiting for events and
so just replace it with wait_event_interruptible. And while at it remove
the useless access_ok() checks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allowing to specify a specific misc minor number for the virtual driver
is pretty much useless and nobody is using this feature. So just remove
it and use MISC_DYNAMIC_MINOR all the time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A driver overhaul on 29 Feb 2000 (!) broke locking around fiddling with
the tx descriptor ring in start_xmit(); a follow-on "fix" removed the
broken remnants altogether. Here's a patch to restore proper locking in
the function -- the complement in the interrupt handler has been correct
all the time.
This *may* have been the reason for the occasional confusion of the chip
-- triggering a tx timeout followed by a chip reset sequence -- seen on
R4k-based DECstations with the onboard Ethernet interface. Another theory
is the confusion is due to an unindentified problem -- perhaps a silicon
erratum -- associated with the variation of the MT ASIC used to interface
the R4k CPU to the rest of the system on these computers; with its
aggressive write-back buffering the design is particularly weakly ordered
when it comes to MMIO (in the absence of ordering barriers uncached reads
are allowed to bypass earlier uncached writes, even if to the same
location), which may trigger all kinds of corner cases in peripheral
hardware as well as software.
Either way this piece of code is buggy.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dereferencing of the private pointer cmsg->m in capi_cmsg2str() may
cause an Oops in case of an error, which is particularly inconvenient
as that function is typically used to format an error message. Add a
NULL pointer check to avoid this.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add kerneldoc comments for the exported funtions in capiutil.c.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of the Kernel CAPI exported function capi_ctr_reseted()
to something representing its purpose better.
Impact: renaming, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for tun_chr_close to race with dellink on the
a tun device. In which case if __tun_get runs before dellink
but dellink runs before tun_chr_close calls unregister_netdevice
we will attempt to unregister the netdevice after it is already
gone.
The two cases are already serialized on the rtnl_lock, so I have
gone for the cheap simple fix of moving rtnl_lock to cover __tun_get
in tun_chr_close. Eliminating the possibility of the tun device
being unregistered between __tun_get and unregister_netdevice in
tun_chr_close.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state)) was being hit
during e100 EEH recovery. The problem source was a napi_enable
call being made during e100_io_error_detected. Napi should remain
disabled after e100_down, and only be reenabled when the interface
is recovered.
This patch also updates e100_io_error_detected in order to make
it similar to the current versions of the error_detected callback
in drivers such as e1000e and ixgbe.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_create_eq() would fail for one of EQ's assigned for
completion handling, the code would try to free the same EQ
we failed to create.
The crash was found by Christoph Lameter
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the right structure while incrementing the offset in tun_get_user.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the private definition of TRUE/FALSE and use the ones from
linux/stddef.h. Also remove the definition of BOOL which is not referenced
inside the driver anyway.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for the Micrel KS8842 ethernet switch.
The supplied code is for driving the KS8842 through the Timberdale FPGA
on the Russellville board, a development board for Intel Atom CPU
in the automotive area.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all current versions of virtio_net generate a value for the
header length that's too small, we should optimise this so that
we don't copy it twice. This can be done by ensuring that it is
at least as large as the place where we'll write the checksum.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through a bug in the tun driver, I noticed that virtio_net is
producing bogus hdr_len values. In particular, it only includes
the IP header in the linear area, and excludes the entire TCP
header. This causes the TCP header to be copied twice for each
packet. (The bug omitted the second copy :)
This patch corrects this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes an initialization error; the chip negotiates gigabit, but
the driver mistakenly handled it as 100Mb.
Changes based on both SiS own GPL driver and forcedeth.
Hopefully should fix
http://bugzilla.kernel.org/show_bug.cgi?id=9735http://bugzilla.kernel.org/show_bug.cgi?id=11149
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected dma sync handling on small packets. Should fix
http://bugzilla.kernel.org/show_bug.cgi?id=11509
Note:
While this bug was reported only on x86_64, it could have affected
any architecture.
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware mailbox commands require the firmware to
communicate with the FCoE driver running on another
PCI function. This can potentially take several seconds.
This wait is done in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 8 banks of 'sub-registers' each of which are accessed
through address/data register pair. An example would be reading
flash or the xgmac. Accessing these require the driver to wait for
a ready bit before writing the address and then accessing the data.
This patch increases the timeout to 100us to prevent timeouts
that have been seen on some platforms.
These register are accessed in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since an FCoE function shares a port with this NIC function, the
jumbo settings must always be in place. This patch causes the
hardware to be set up for jumbo if it is not already done.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each firmware mailbox command can have a different number of
valid data elements. When waiting for a mailbox command to
complete it the process passes it's element count and
waits for the completion. It is possible that while waiting
an unrelated firmware async event (AE) can arrive. When this
happens, the handler will over write the element count
with the value for the newly arrived AE. This can cause
the mailbox command to not get all of it's data.
This patch restores original mailbox count at the end
of the handler.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check status on every iteration of event handler loop and exit
if an error occurred. If an error occurred then recover process
will be queued so this loop should no continue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x_drv_remove() function is declared with __devexit, so the
assignment to the driver structure needs __devexit_p() wrappings to prevent
build failure when hotplug is disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver works fine on Blackfin systems, so add it to the arch
list in the Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IDE_DFLAG_NIEN_QUIRK device flag and use it instead of
drive->quirk_list.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_nien_quirk_list() helper to the core code
and then use it in ide_port_tune_devices().
* Remove no longer needed ->quirkproc methods from hpt366.c
and pdc202xx_{new,old}.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enable also quirks in do_reset1() and ide_config_drive_speed()
for devices on quirk_drives[] list.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With ->write_devctl method call (which unmasks drive IRQ) preceding
SELECT_MASK() call there is really no need for the latter.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We always call SELECT_MASK(drive, 0) after ide_dev_read_id() call
so there is no need to do it again in the error path.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[inspired by pata_icside]
Enabling/disabling of card IRQs is handled fine by IRQ and IDE
subsystems so there is no need for custom ->maskproc method.
Moreover icside_maskproc() would enable IRQ only if it was already
enabled [because of 'if (state->enabled && !mask)' check].
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These flags used to be bit numbers and now are single bits in the
->atapi_flags vector. Use them properly.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are two sites where the flag is being changed: ide_retry_pc
and idetape_do_request. Both codepaths are protected by hwif->busy
(ide_lock_port) and therefore we shouldn't need the atomic accesses.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's resetproc() method resets both channels at once -- most probably
by driving RESET- on them. Not only such reset can severely disturb concurrent
operations on another channel, it also ensues 2-second delay, while there's no
apparent reason why SRST reset being performed prior to resetproc() call needs
to be followed up by another reset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_lost_irq() and dma_clear() methods call pdc202xx_reset()
which resets both channels at once -- most probably by driving RESET- on them.
Not only such reset can severely disturb concurrent operations on another
channel, it is also a clear overkill (especially in the first case) and is
completely unexpected and thus not properly handled by the IDE core in this
context (in the second case the usual SRST reset would most probably ensue
anyway though); it also causes quite arbitrary 2-second delay. Hence, use the
standard ide_dma_lost_irq() method and don't install the optional dma_clear()
method at all -- the driver should do well without this age-old cruft...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_test_irq() method, although tests some chip specific interrupt
bits, finally always relies on the SFF-8038i standard interrupt bit. I see no
point in testing the bits that are not trusted anyway -- the driver should be
fully able to use the standard method implemetation, ide_dma_test_irq().
With this change 'pdc202xx_dma_ops' finally becomes identical to 'sff_dma_ops',
and we can get rid of it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a FW running that helps manage the internal SFI PHY. There are
also a number of pre-production samples of these SFI-based devices in the
field. This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified. The driver will continue loading
though, with no functional degradation.
Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables Flow Director's ATR functionality to the main base
driver for 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functions for ixgbe to initialize Flow Director. It
also has the function APIs to add Flow Director filters from the base
driver. This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director. This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from. This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a second feature flag variable to use for future feature
expansion. Add HW RSC to this new feature flags variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine. This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v_idx value was being used as both a bitmask and an index. This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags. This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner. This will restart the autotry
mechanism to get link into a known state. The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ethtool internal test engine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY. The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps. This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY. This ensures we don't collide with the FW.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 KX4 device defaults to legacy power management, or APME. This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit ac95beedf8 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds a new device id for mcp89 chipset.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the device id macros and instead uses the constants
directly.
The areas in which logic expressions where using the macros now instead
use feature/workaround flags.
No new functionality has been introduced in this patch, only clean up of
flags and macros.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/pci: fix mmconfig detection with 32bit near 4g
PCI: use fixed-up device class when configuring device
Added support for the new xps tft controller. The new core
has PLB interface support in addition to existing DCR interface.
Removed platform device support as both MicroBlaze and PowerPC
use device tree.
Previously, the dcr interface was assumed to be used in mmio mode,
and the register space of the dcr interface was precomputed and stuffed
into the device tree. This driver now makes use of the new dcr
infrastructure to represent the dcr interface. This enables the dcr
interface to be connected directly to a native dcr interface in a clean
way.
Added compatibility for ml507 dvi core.
Signed-off-by: Suneel <suneelg@xilinx.com>
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Some ALi devices report simplex if they have been disabled and re-enabled, and
restoring the byte does not work. Ignore it - the needed supporting logic is
already present for the SATA ULi ports.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DaVinci clock support has been updated in mainline.
Update clock names accordingly.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: Add HP Compaq nc6000 to the broken poweroff list
ahci: add warning messages for hp laptops with broken suspend
pata_efar: fix PIO2 underclocking
pata_legacy: wait for async probing
HP Compaq nc6000 suffers from the double disk spindown issue.
Add it to the broken poweroff DMI list.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Harddisks on HP dv[4-6] and HDX18 fail to come online after resume on
earlier BIOSen. Fortunately, HP recently released BIOS updates for
all machines to fix the issue. Detect old BIOSen, warn the user to
update BIOS on boot and suspend attempts and fail suspend.
Kudos to all the bug reporters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: kernel.org@epperson.homelinux.net
Cc: emisca@gmail.com
Cc: Gadi Cohen <dragon@wastelands.net>
Cc: Paul Swanson <paul@procursa.com>
Cc: s@ourada.org
Cc: Trevor Davenport <trevor.davenport@gmail.com>
Cc: corruptor1972 <steven_tierney@yahoo.co.uk>
Cc: Victoria Wilson <mail@vwilson.co.uk>
Cc: khiraly <khiraly.list@gmail.com>
Cc: Sean <wollombi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The basic problem here that pata_legacy attaches the host, sees if it found
any devices and detaches it if none were found. With async probing, it's not
waiting until discovery is finished before deciding it has no devices and
trying the detach leading to this warning:
ata1: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
------------[ cut here ]------------
WARNING: at drivers/ata/libata-core.c:6222 ata_host_detach+0x75/0x90()
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.30-rc7 #1
Call Trace:
[<c01fbb05>] ? ata_host_detach+0x75/0x90
[<c01fbb05>] ? ata_host_detach+0x75/0x90
[<c01139b5>] ? warn_slowpath_common+0x45/0x80
[<c01139fa>] ? warn_slowpath_null+0xa/0x10
[<c01fbb05>] ? ata_host_detach+0x75/0x90
[<c02f40e0>] ? legacy_init+0x44e/0x87f
[<c02f3c92>] ? legacy_init+0x0/0x87f
[<c0101021>] ? _stext+0x21/0x140
[<c01890ff>] ? proc_register+0x2f/0x190
[<c018938c>] ? create_proc_entry+0x5c/0xc0
[<c0135ebe>] ? register_irq_proc+0x6e/0x90
[<c02e6484>] ? kernel_init+0x6e/0xbf
[<c02e6416>] ? kernel_init+0x0/0xbf
[<c01031d7>] ? kernel_thread_helper+0x7/0x10
---[ end trace ef1ee36e873ae3a0 ]---
Because it detaches before the probe is complete.
One way to fix it would be to put an async_synchronize_full() before looking
for devices, which this patch does. A better way might be to separate libata
into its own domain and only wait for that.
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reverts commit 6c51d1cfa0, which
apparently causes DRI initialization failures on Radeons.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Requested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ivtv stream buffers may be for receive or for send but the attached
sg handle is always destined cpu->device. We flush it correctly but the
allocation is wrongly done with the same type as the buffers.
See bug: http://bugzilla.kernel.org/show_bug.cgi?id=13385
(Note this doesn't close the bug - it fixes the ivtv part and in turn
the logging next shows up some rather alarming DMA sg list warnings in
libata)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a PNP resource range check function, indicating whether a resource
has been assigned to any device.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
[apw@canonical.com: fixed up exports et al]
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The sysrq functions are executed in hardirq context, so we shouldn't be
calling sleeping functions from them, like mutex_locks or memory
allocations.
Fix up the i915 sysrq handler to avoid this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix a FIXME in the intel LVDS bring-up code, adding the appropriate
blacklist entry for the AOpen Mini PC, courtesy of a dmidecode
dump from Florian Demmer.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: Florian Demmer <florian@demmer.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The general definition block contains the child device tables, which include
the SDVO device info. For example: device slave address, device dvo port,
device type.
We will get the info of SDVO device by parsing the general definition blocks.
Only when a valid slave address is found, it is regarded as the SDVO device.
And the info of DVO port and slave address is recorded.
http://bugs.freedesktop.org/show_bug.cgi?id=20429
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds the register definitions for the display port enable register
along with those for the GMCH and Link M/N ratios required to drive display
port outputs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can safely assume that cursor addresses will not extend beyond the
addressable screen dimensions; setting the additional bits is harmless in
any case.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect TV connect status by setting DAC voltage level override
values as 0.7 voltage for DAC_A/B/C. The corresponding 2-bits shold be 0x2,
In order correctly to set last bit as 0, at first we must clean it.
It fixed freedesktop.org bug #21204
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds kernel mode setting on IGDNG with VGA output support.
Note that suspend/resume doesn't work yet.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[anholt: dropped drm_pciids.h hunk to avoid loading an incomplete driver]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: ignore EDID with really tiny modes.
drm: don't associate _DRM_DRIVER maps with a master
drm/i915: intel_lvds.c fix section mismatch
drm: Hook up DPMS property handling in drm_crtc.c. Add drm_helper_connector_dpms.
drm: set permissions on edid file to 0444
drm: add newlines to text sysfs files
drm/radeon: fix ring free alignment calculations
drm: fix irq naming for kms drivers.
While running 20 parallel instances of dd as follows:
#!/bin/bash
for i in `seq 1 20`; do
dd if=/dev/zero of=/export/hda3/dd_$i bs=1073741824 count=1 &
done
wait
on a 16G machine, we noticed that rather than just killing the processes,
the entire kernel went down. Stracing dd reveals that it first does an
mmap2, which makes 1GB worth of zero page mappings. Then it performs a
read on those pages from /dev/zero, and finally it performs a write.
The machine died during the reads. Looking at the code, it was noticed
that /dev/zero's read operation had been changed by
557ed1fa26 ("remove ZERO_PAGE") from giving
zero page mappings to actually zeroing the page.
The zeroing of the pages causes physical pages to be allocated to the
process. But, when the process exhausts all the memory that it can, the
kernel cannot kill it, as it is still in the kernel mode allocating more
memory. Consequently, the kernel eventually crashes.
To fix this, I propose that when a fatal signal is pending during
/dev/zero read operation, we simply return and let the user process die.
Signed-off-by: Salman Qazi <sqazi@google.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Modified error return and comment trivially. - Linus]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Nomadik 8815 SoC has a slightly modified version of the PL011 block.
The patch uses the different ID value as a key to select a vendor
structure that is used to keep track of the differences, as suggested
by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes code (deprecated by "cfg80211: add rfkill support" )
main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)
and a useless device state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing a comment in the code describing this module parameter.
The description printed when user runs "modinfo" is correct.
Reported-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the link quality parameters inside the functions,
adding #define in iwl-commands.h to shared by different functions.
Also include the valid range for number of link quality parameters.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wait until ucode is loaded and driver receive ALIVE_REPLY then switch
to ICT interrupt. This ensures we receive all interrupts indicating
successful ucode load.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the bug at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1903
when SW rfkill is invoked by 'iwconfig txpower off',
the existing connection disassociates and led off command is sent
to the device which returns error as rfkill is 'true'.
Patch fixes this by just avoiding sending the led off/on command when
disassociated. The main purpose of the led_disassociate callback
is to start or stop the blinking.
There are three states in led
1) Always on when radio is on
2) Always off when radio is off
3) blink when associated and if there is some traffic.
In this callback 'allow_blinking' needs to be set false
when associated, as LED will be always on.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port "iwlcore: Allow skb allocation from tasklet." to 3945
If RX queue becomes empty then we need to restock the queue from
tasklet to prevent ucode from starving. A caller to iwl_rx_allocate
will decide if allocated buffer should come from GFP_ATOMIC or
GFP_KERNEL.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No more reinitialization is needed in the post reset hook, remove
the FIXME comment.
While at it, clean up whitespaces in the immediate surrounding.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidraw accepts any devices, no matter if the device has
already been claimed by other HID driver (hid-input, hidraw), and
this is intended to stay. Fix up the comment to reflect reality.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The i2c-ibm_iic driver printed messages in an odd order that seemed
to list devices before the driver was probed.
Here is an example:
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ibm-iic ef600700.i2c: using standard (100 kHz) mode
ad7414 0-004a: chip found
This changes the order to print the i2c driver message before scanning
for devices so that the logs show the driver, then the devices.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client. There may even have been problems
with cooperative clients versus cooperative clients. So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.
Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old. This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting. Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This may fix cursor corruption in X on resume, which would persist until
the cursor was hidden and then shown again.
V2: Also include the cursor control regs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This could be triggered by a gtt mapping fault on 965 that decides to
remove the fence from another object that happens to be active currently.
Since the other object doesn't rely on the fence reg for its execution, we
don't wait for it to finish. We'll soon be not waiting on 915 most of the
time as well, so just drop the BUG_ON.
Signed-off-by: Eric Anholt <eric@anholt.net>
The device class may be changed after the fixup, so re-read the class
value from pci_dev when configuring the device. Otherwise some devices
such as JMicron SATA controller won't work.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use printk format specifier for MAC address.
Remove DECALRE_MAC_BUF and print_mac() usage in the driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added socket accounting to tun I inadvertently introduced
spurious wake-up events that kills qemu performance. The problem
occurs when qemu polls on the tun fd for read, and then transmits
packets. For each packet transmitted, we will wake up qemu even
if it only cares about read events.
Now this affects all sockets, but it is only a new problem for
tun. So this patch tries to fix it for tun first and we can then
look at the problem in general.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic MDIO generic values.
Based on Ben Hutchings'review comments.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some EDIDs lie and report tiny modes that aren't possible. Ignore
these modes.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A driver will use the _DRM_DRIVER map flag to indicate that it wants
to be responsible for removing the map itself, bypassing the DRM's
automagic cleanup code.
Since the multi-master changes this has been broken, resulting in some
drivers having their registers unmapped before it's finished with them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
intel_no_lvds[] does not require __initdata as it is used only by
void intel_lvds_init(struct drm_device *dev).
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without initializing the sysfs attributes for the edid file,
it was created with mode 0, making it difficult for applications to use.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The contents of various simple text files in sysfs should end with
a newline to make them easier to read from the console.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fd.o bz#21849
We were aligning to +16 dwords, instead of to the next 16dword
boundary in the ring. Fix the calculation to go to the next 16dword
boundary when space checking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.
So this is the cleaner version that just picks devname or driver name
in the irq code.
It removes the devname allocs from the i915 driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the fields in the control block are nicely right-aligned, so no
masking is necessary.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Freescale eSDHC controller has the special order for
the HOST version register. that is not same as the other's
registers. The address of HOSTVER in spec is 0xFE, and
we need use the in_be16(0xFE) to access it, not in_be16(0xFC).
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Especially with Sandisk SDHC cards, the second SWITCH command was failing
with a timeout and the card was not recognized at all. However if the
system was busy, or debugging was enabled, or a udelay(100) was inserted
before the second SWITCH command in the core code, then the timing was
so that the card started to work.
With some unusual block sizes, the data FIFO status doesn't indicate a
"empty" state right away when the data transfer is done. Queuing
another data transfer in that condition results in a transfer timeout.
The empty FIFO bit eventually get set by itself in less than 50 usecs
when it is not set right away. So let's just poll for that bit before
configuring the controller with a new data transfer.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Empirical evidences show that this is causing far more problems than it
solves when this mode is enabled in the host hardware. Amongst those
cards that are known to be non functional when this bit is set are:
A-Data "Speedy" 2GB SD card
Kodak 512MB SD card
Ativa 1GB MicroSD card
Marvell 8688 (WIFI/Bluetooth) SDIO card
Since those cards do work on other host controllers which do honnor the
hs timing, the issue must be with this particular host hardware.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* iwm doesn't depend on cfg80211 or wireless extensions
* rndis wlan selects cfg80211 - needs to depend
* mac80211 selects cfg80211 - needs to depend
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove the active interface, there's no need to continue
sending beacons; doing so would cause a null pointer deref in
ieee80211_beacon_get(). Disable the interrupt in remove_interface
and add a WARN_ON(!vif) in case there are other instances lurking.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help when reviewing issues regarding regulatory
domain on ath5k/ath9k/ar9170.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle error condition on copy_from_user() properly and
make sure a NUL terminated char[] is sent to strict_strtoul()
for proper conversion.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Which means removing all rfkill code since it only does
soft-kill which cfg80211 will now handle in exactly the
same way the driver did.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is to incorporate Dan Williams' comments for commit:
"libertas: implement function init/shutdown commands for SD8688"
1. remove fn_init_required and fn_shutdown_required variables from
lbs_private structure. If required, __lbs_cmd() will be called
directly to send function init/shutdown command for SD8688 in
if_sdio_probe() or if_sdio_remove() callback.
2. add global variable "user_rmmod" to distinguish between the module
removal case and the card removal case. This flag will be checked in
if_sdio_remove() against SD8688 card to determine whether or not the
function shutdown command needs to be sent.
3. remove "card" from if_sdio_model structure as it cannot store
card pointers for multiple cards. Besides, it's no longer needed
to store the "card" pointer with changes #1 & #2 above.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the statically allocated p54usb firmware string, and
replaces them with const char pointers.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwmc3200wifi: trim down calibration firmware name
The patch trims down iwmc3200wifi calibration firmware name from
iwmc3200wifi-lmac-calib-sdio.bin to iwmc3200wifi-calib-sdio.bin. We can
shorten the firmware name because all calibration is done by LMAC.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"[PATCH 3/4 v2] ar9170: fix LED power state handling" revealed
a bug which can cause a ugly crash.
The delayed worker is canceled before the LED class functions are
unregistered... So, if something manages to update the LEDs
while unregister routine is running the timer could fire _after_ the
module has been unloaded.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains a few more mostly random fixes for the USB front-end.
1. handle irq command response, instead of printing it to the console.
2. remove fixed FIXME.
(real fix: "ar9170usb: reset device on resume". )
3. some more one-liner.
- get rid of a useless "return;"
- add a few branch prediction hints in hot-paths
etc.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of Johannes' deadlock report by moving the
mutex_lock right after cancel_work_sync in ar9170_op_stop.
Besides, the janitor does not need to hold the mutex anymore,
so this extra lines can be removed as well.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a minor visual bug in the led code, which
left the LED in the wrong power state when it was toggled
in a _unexpected_ way (e.g: enabling the LED twice).
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in configure_filter's (sub-)routines.
We never really cleared the flags once we updated the hardware state,
so we wasted our resources by applying already active settings.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces 3 new function which are used to update
the MAC state, whenever needed... e.g: after a band switch.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replace a few constant magics which may affected
the device when operating in a 40MHz channel.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch only contains a few uncritical updates for the
hardware definition header.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a simple copy & paste error that affected beacon
transmission in 802.11a mode.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the use of the deprecated radio_enabled setting
and code associated with that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds:
USB 0x057C:0x8401 AVM FRITZ!WLAN USB Stick N
USB 0x057C:0x8402 AVM FRITZ!WLAN USB Stick N 2.4
These devices require the 1-stage firmware, if not present we
don't continue.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
You can get the stage 1 firmware from here:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/ar9170.fw
md5sum: 34feec4ec0eae3bb92c7c1ea2dfb4530
sha1sum: 6e5250498b815c2940d97242de31e054ae44e079
Its license:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/LICENSE
This is a new firmware, tested with WNDA3100.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like mac80211 can request the driver to start beaconing with
a beacon interval of zero in some cases (at least for mesh point). This
does not sound correct and something may need to be fixed in
mac80211. However, taken into account the unpleasantness of getting
stuck in an infinite busy loop with rtnl_lock held, let's add a quick
workaround in the driver to avoid the worst symptom while someone more
familiar with the mesh implementation can figure out what should be done
with mac80211 as far as beacon interval configuration is concerned.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the debug file to the ath9k debugfs, which lets you modify
the debug_mask at runtime, without having to reload the ath9k module.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch combines the legacy and 11n rcstats into one, using the normal
rate table indices instead of two separate indices for each mode. Legacy
rates also get all of the PER and retry information, now, too.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I have a TrendNet 652-BRP running OpenWRT + ath9k very well. The only
problem is that the beacon gets stuck maybe once a day. After
Vasanthakumar Thiagarajan's "ath9k: cleanup beacon parameters
configuration" patch, ath9k would nearly re-configure the beacons after it
detected the stuck beacon, and did a reset. But it would fail the
SC_OP_TSF_RESET check in ath_beacon_config_ap. This patch gets the beacon
fully reconfigured after the reset.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format for size_t variable:
drivers/net/wireless/iwmc3200wifi/fw.c:75: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: ilw@linux.intel.com
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were sending the fragmentation threshold value to the wrong table,
causing an LMAC assert when setting it from wext.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building when CONFIG_IWLWIFI_DEBUG is not set, we get the following
warning:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c: In function ‘iwl_isr’:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c:1707: warning:
unused variable ‘inta_fh’
This patch avoids this warning by adding #ifdef CONFIG_IWLWIFI_DEBUG
before the declaration of inta_fh in iwl_isr() in
drivers/net/wireless/iwlwifi/iwl-core.c
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oddly enough, the firmware's JOIN/START commands don't appear to have
any facility for setting custom IEs, thus the started adhoc network
doesn't advertise its WPA capability in the beacon. Whee!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And fix up setting authentication suite for v9+ firmware too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Easier to read and more conformant with kernel style.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the parameters for association/join/start commands aren't
used (like the FH and CF IEs for IBSS, and the FH IE for BSS), so
get rid of their unions to reduce indirection. Also clean up
structure names for kernel style.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Polling function returns positive time if polling was needed to
read value. This is still success.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hunk of code was removed in patch "iwlwifi: do not
cancel delayed work inside spin_lock_irqsave" submitted at
http://marc.info/?l=linux-wireless&m=124267503030042&w=2
This same patch in this repo does not remove this hunk.
Remove it here.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
new patch to add more usb_dev to rt2800usb.c .
IDs 'stolen' from the latest Ralink linux
driver(2009_0520_RT3070_Linux_STA_v2.1.1.0.tar.gz)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment (which I remove) says that the translation is done SPI routines.
IMHO this can't work because the SPI driver does not know whether the incomming
bytes are part of the registers/bytes which need to be flipped or part of
packet data which has to remain untouched.
While adding le helpers I also removed spu_write_u32() which has no users.
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code makes the UCC whose register range includes the current mdio
register to be the MII managemnt interface master of the QE. If there is more
than one mdio bus for QE, the UCC of the last mdio bus will be the MII
management interface master which will make the primary mdio bus working
unproperly, e.g. can not get the right clock. Normally the primary mdio bus is
the first UEC's mdio bus.
This patch allows the first UCC to be the MII management interface master of the
multiple UCC mdio buses.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable fiber/copper auto selection for Marvell m88e1111 SGMII support.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With bi-directional stress traffic, the receiver could hang causing the
hardware to stop and a "Detected Tx Unit Hang" message dumped to the system
logfile. Temporarily workaround this issue by disabling Tx flow control by
default. The issue is currently being investigated and a follow-on patch
will be provided to revert this when it is resolved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters. These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions). New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown. Check for
support before attempting to disable the feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed oops when calling device_unregister followed by device_register
(changing __init to __devinit) and removed request_mem_region() as
platform_device_register already does this which can result in EBUSY
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
blk_queue_bounce_limit() is more than a wrapper about the request queue
limits.bounce_pfn variable. Introduce blk_queue_bounce_pfn() which can
be called by stacking drivers that wish to set the bounce limit
explicitly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.
This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...
Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65
In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
