Commit Graph

147 Commits

Author SHA1 Message Date
Ivo van Doorn
4789666e13 rt2x00: Hardcode TX ack timeout and consume time
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.

After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.

The symptoms of this problem:
 - Rate control module always falls back to 1Mbs
 - Low throughput when bitrate was fixed

Possible side-effects (not confirmed but highly likely)
 - Problems with DHCP
 - Broken connections due to lack of probe response

This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-09 11:18:14 -04:00
Igor Perminov
d6756d0dc2 rt2x00: Fix beacon de-synchronization while update beacon
When beacon is being updated to refresh TIM (AP mode), beacon frames are
de-synchronizing (i.e. two neighbor beacon frames - before and after
update - are being transmitted with a wrong time interval).
That is because xxx_write_beacon should disable beacon generation only
while beacon data are being uploaded to the device, but it should not
disable the beacon clock.

Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:13:55 -04:00
Igor Perminov
1afcfd54fd rt2x00: FIF_PSPOLL filter flag support
This patch implements FIF_PSPOLL filter flag support in rt2x00 drivers,
which has been introduced in mac80211 (see
http://marc.info/?l=linux-wireless&m=124897986330807&w=2).

Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:13:53 -04:00
Pavel Roskin
117839bd12 rt61pci: fix module reloading
Unloading rt61pci can leave the device in such state that reloading
rt61pci would fail to reinitialize it.  Bogus data would be read from
the EEPROM and the RF version won't be recognized.

It appears that unloading rt61pci with power saving enabled would have
such effect.  To initialize the device properly, SOFT_RESET_CSR should
be set to the same value as rt61pci_config_ps() uses to wake up the
device.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:24 -04:00
Luis Correia
4951348109 rt2x00: Comment spellchecking
Fix a bunch of spelling errors in the rt2x00 drivers

Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:26 -04:00
Stefan Steuerwald
930c06f271 rt2x00: Implement set_tim callback for all drivers
Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.

The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.

Signed-off-by: Stefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:11 -04:00
Ivo van Doorn
e47a5cddf8 rt2x00: use wiphy rfkill interface
Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:27 -04:00
Ivo van Doorn
6b347bff14 rt2x00: Remove last usage of beacon_int from ieee80211_config
This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-03 14:05:10 -04:00
Ivo van Doorn
8a566afea0 rt2x00: Remove usage of IEEE80211_CONF_CHANGE_BEACON_INTERVAL
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22 14:06:04 -04:00
Johannes Berg
2d0ddec5b2 mac80211: unify config_interface and bss_info_changed
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06 15:14:36 -04:00
Ivo van Doorn
440ddadaee rt2x00: Move Move pci_dev specific access to rt2x00pci
pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Ivo van Doorn
53bc647a1a rt2x00: Remove check for rf word 0
The only way rf_write() can be called with word 0 is
when the user sends the wrong word index through debugfs.
However the values which are send through debugfs are
validated using the RF_BASE and RF_SIZE macro values,
the most logical solution is to increase RF_BASE with 4
and decrease RF_SIZE with 4 (RF_SIZE has always been
1 word too big)

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27 14:52:35 -05:00
Ivo van Doorn
0cbe006461 rt2x00: Validate firmware in driver
The get_firmware_crc() callback function isn't flexible
enough when dealing with multiple firmware versions.
It might in some cases be possible that the firmware
file contains multiple CRC checksums.

Create the check_firmware() callback function where the driver
has complete freedom in how to validate the firmware.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:35 -05:00
Ivo van Doorn
a2c9b652a1 rt2x00: Add kill_tx_queue callback function
provide rt2x00lib the possibility to kill a particular TX queue.
This can be useful when disabling the radio, but more importantly
will allow beaconing to be disabled when mac80211 requests this
(during scanning for example)

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:34 -05:00
Ivo van Doorn
9752a7bd7f rt2x00: Restrict firmware file lengths
Add extra security to the drivers for firmware loading,
check the firmware file length before uploading it to
the hardware. Incorrect lengths might indicate a firmware
upgrade (which is not yet supported by the driver) or
otherwise incorrect firmware.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:01:26 -05:00
Ivo van Doorn
5e79002362 rt2x00: conf_tx() only need register access for WMM queues
conf_tx() in rt61pci and rt73usb only have to check once
if the queue_idx indicates a non-WMM queue and break of
the function immediately if that is the case.

Only the WMM queues need to have the TX configuration written
to the registers.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:00:46 -05:00
Ivo van Doorn
4e54c711b4 rt2x00: Update copyright year to 2009
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:00:45 -05:00
Johannes Berg
4be8c3873e mac80211: extend/document powersave API
This modifies hardware flags for powersave to support three different
flags:
 * IEEE80211_HW_SUPPORTS_PS - indicates general PS support
 * IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
 * IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device

It also adds documentation for all this which explains how to set the
various flags.

Additionally, it fixes a few things:
 * a spot where && was used to test flags
 * enable CONF_PS only when associated again

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:59:58 -05:00
Ivo van Doorn
076f9582a6 rt2x00: Remove ENTRY_TXD_OFDM_RATE
The flag ENTRY_TXD_OFDM_RATE isn't flexible enough
to indicate which rate modulation should be used for
a frame. This will become a problem when 11n support
is added.

Remove the flag and replace it with an enum value which
can better indicate the exact rate modulation.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:58:40 -05:00
Ivo van Doorn
91581b6272 rt2x00: Split EEPROM_NIC_TX_RX_FIXED
The 2 bits in EEPROM_NIC_TX_RX_FIXED each influence
a different antenna. We might as well split the
definition and directly read the correct bit.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:58:38 -05:00
Ivo van Doorn
5352ff6510 rt2x00: Restrict interface between rt2x00link and drivers
Restrict drivers to only access link_qual structure during
link tuning. The contents of these fields are for the drivers
and all fields are allowed to be changed to values the driver
considers correct.

This means that some fields need to be moved outside of this
structure to restrict access only to rt2x00link itself.
This allows some code to be moved outside of the rt2x00.h header
and into rt2x00link.c.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:58:35 -05:00
Ivo van Doorn
eb20b4e8a6 rt2x00: Reduce calls to bbp_read()
The link_tuner() function will always call bbp_read()
at the start of the function. Because this is an
indirect register access has some costs attached
to it (especially for USB hardware).

We already store the value read from the register
into the vgc_level value inside the link structure.
Instead of reading from the register we can read that
field directly and base the tuner on that value.

This reduces the time the registers are locked with
the csr_mutex and speeds up the link_tuner processing.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:58:34 -05:00
Ivo van Doorn
7d7f19ccb7 rt2x00: Implement Powersaving
Listen to IEEE80211_CONF_PS to determine if the device
should drop into powersaving mode. This feature depends
on the dynamic power save functionality in mac80211.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:58:34 -05:00
Ivo van Doorn
74415edb04 rt2x00: Add RXDONE_CRYPTO_IV/ICV flags
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
	* rt2500usb provides ICV inside the frame
	* rt2800pci doesn't provide IV/ICV
	* rt2800usb doesn't provide IV/ICV

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05 09:35:56 -05:00
Ivo van Doorn
1ce9cdac48 rt2x00: Optimize IV/EIV handling
IV and EIV belong to eachother and don't require
2 seperate fields. Instead they can logically be
merged into a single array with size 2.

With this approach we can simplify the code in
rt2x00crypto.c by using a single memcpy() when
copying the iv/eiv data. Additionally we can
move some code out of if-statements because the
if-statement would always be true.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05 09:35:50 -05:00
Ivo van Doorn
c9c3b1a5de rt2x00: Cleanup indirect register access
All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.

This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25 16:32:53 -05:00
Ivo van Doorn
8ff48a8bbe rt2x00: Fix race condition when using inderect registers
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.

USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:08:16 -05:00
Ivo van Doorn
798b7adb4e rt2x00: Cleanup TX/RX entry handling
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.

rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:08:16 -05:00
Ivo van Doorn
743b97caf9 rt2x00: Remove debugfs CSR access wrappers
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10 15:17:35 -05:00
Ivo van Doorn
e4ea1c403a rt2x00: Optimize configuration handling
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.

 * Remove set_retry_limit callback function, handled
   through config()
 * Move config_antenna to its own callback function,
   it isn't handled by mac80211 anymore
 * Use IEEE80211_CONF_CHANGED_* flags and remove manual
   checks
 * Removed deprecated short slot setting through config()
   and put it in config_erp() through which mac80211 now
   configures it
 * Remove config_phymode() and move contents to config_erp()
   since it only managed the basic rates which is now
   determined by mac80211 through config_erp().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10 15:17:33 -05:00
John Daiker
558875112c rt2x00: reduce checkpatch.pl errors
A few changes to reduce checkpatch.pl errors in the rt2x00 driver.  For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!

Diff is against wireless-testing HEAD.

Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31 19:00:40 -04:00
Johannes Berg
9124b07740 mac80211: make retry limits part of hw config
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31 19:00:14 -04:00
Johannes Berg
e174961ca1 net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:06:18 -07:00
Ivo van Doorn
acaf908d40 rt2x00: Fix HW crypto key handling
When a crypto key is being removed, rt2x00mac should not
reset the key->hw_key_idx value because that will prevent
the driver from removing the correct key from the hardware.

Furthermore ffz() starts counting at 0 instead of 1, so we don't
need to substract 1 from the resulting value.

Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-24 16:18:03 -04:00
Ivo van Doorn
771fd56519 rt2x00: Make rt2x00 LEDS invisible config option
There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-11 15:53:38 -04:00
Ivo van Doorn
5816952998 rt2x00: Make RFKILL enabled by default
RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.

Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.

This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-11 15:53:38 -04:00
Ivo van Doorn
6c6aa3c004 rt2x00: Add Signal type flag
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-29 16:24:12 -04:00
Ivo van Doorn
2af0a570b4 rt2x00: Initialize txop during conf_tx() callback
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-29 16:24:12 -04:00
Ivo van Doorn
0262ab0df6 rt2x00: Fix race conditions in flag handling
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.

The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)

Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:

rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.

Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-29 16:24:11 -04:00
Ivo van Doorn
008c44825d rt2x00: Add module parameter to disable HW crypto
Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22 16:29:59 -04:00
Ivo van Doorn
ba2ab47129 rt2x00: Move lna_gain calculation to config() callback
We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.

This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22 16:29:59 -04:00
Ivo van Doorn
8c5e7a5f59 rt2x00: Gather channel information in structure
Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22 16:29:58 -04:00
Ivo van Doorn
61e754f44b rt2x00: Implement HW encryption (rt61pci)
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22 16:29:58 -04:00
Ivo van Doorn
e6d3e90208 rt2x00: rt61pci needs another millisecond after firmware upload
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.

Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-01 15:31:34 -04:00
Ivo van Doorn
5adf6d63c1 rt2x00: Fix QOS sequence counting
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.

By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-29 16:55:05 -04:00
Johannes Berg
605a0bd66d mac80211: remove IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE flag
I forgot this in the previous patch that made it unused.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-29 16:36:24 -04:00
David S. Miller
49997d7515 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	Documentation/powerpc/booting-without-of.txt
	drivers/atm/Makefile
	drivers/net/fs_enet/fs_enet-main.c
	drivers/pci/pci-acpi.c
	net/8021q/vlan.c
	net/iucv/iucv.c
2008-07-18 02:39:39 -07:00
David S. Miller
fc943b12e4 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2008-07-14 20:40:34 -07:00
David S. Miller
2aec609fb4 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	net/netfilter/nf_conntrack_proto_tcp.c
2008-07-14 20:23:54 -07:00
David Woodhouse
751851af7a Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Conflicts:

	sound/pci/Kconfig
2008-07-14 15:51:11 -07:00