Replaced et131x_phy.c magic numbers specifying registers and their values with defines, defined in et131x_phy.h
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VMI_* set of register defines are not used, and duplicate the set of PHY_* registers from the same file, which are used - hence removing.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cached_mask_value is only ever assigned, never read. Remove it.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
registry_rx_mem_end is not referenced anywhere in the driver.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As et131x_adjust_link is called from the phydev in response to a netif_carrier_[on|off], and is the only caller of et131x_mii_check, we don't need to call netif_carrier_[on|off] again.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PHY interrupt is now handled by the phy_device, and the equivalent code is present in et131x_adjust_link, called from the phy_device when needed.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
adapter->speed_duplex was never referenced.
adapter->registry_phy_coma was always set to zero, even in the vendor driver.
Removing all member references and associated dead code.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The phy device keeps a note of the duplex mode, so use that value instead of duplex mode.
Also use the phydev defines for duplex modes, and remove the driver private ones.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The phy device keeps a note of the link speed, so use that value instead of the driver private one.
Also use the phydev defines for link speeds, and remove the driver private ones.
adapter->hw_errs was never used, even in the vendor driver, so remove that too.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I think the kernel style cleanups are done now.
Adding myself as a recipient of patches.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of my previous hacking attempts have not been following the rules.
All fixes either lines > 80 chars or whitespace corrections (spaces->tabs etc).
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use defines from include/linux/mii.h instead of et131x_phy.h and delete the latter defines.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now we are using a phy_device, remove driver functionality that is now handled by the phydev.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handing over ioctls handled by the driver to the phydev.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding some basic ethtool ops and supporting functionality using a phy device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Manual setting of speed/duplex will be achieved using ethtool.
Remove the driver specific module_param that also does this.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A mechanism used to set the phy in loopback mode is not present in the driver, making associated checks and variables redundant. Removing them.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xcvr_id holds the phy ID which is stored but never used in the driver.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updating the tx trans_start before closing the device prevents a possible tx_timeout occuring during the closing process.
Tested on an ET1310 device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove redundant code around netif_carrier_XXX calls, and associated adapter->media_state, which prevented the link from being reported as off.
Tested on an ET-1310 device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Used regex (from vim) :%s/\<etdev\>/adapter/g
Changed because:
* 'etdev' is easily confused as a misspelling of 'netdev'
* 'adapter' is more widely used for this struct type in net drivers. This
change made comparing code with other drivers much easier.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Function et131x_set_mac_addr() contains commented out code that has been moved to
et131x_change_mtu() in the same file.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also some minor code clean-ups.
Tested on an ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is impossible to get to this function with the pointer being NULL.
Tested on an ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Typo in header file. Also renaming a few adapter references to fit in with the rest of the file.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed commented out calls that no longer exist in the net_device struct.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This mistake was introduced in the patch 'staging: et131x: Convert et1310_address_map.h names from camel case'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Making finger pointing that bit easier.
Tested on an ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also renamed some items to improve readability, and other minor tidy-ups.
Tested on an ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The comment at the top of the function states 'we need to initialize all the macstat registers to zero', but not all macstat registers are zeroed. Zero the missing registers.
Tested on an ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I must remember to run checkpatch on 'trivial' patches too...
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial rename of the adapter flags struct member to remove camel case.
Tested on a ET-131x device.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes the associated checkpatch warnings.
Tested with ifconfig/general use of a device (Agere Systems ET-131x PCI-E
Ethernet Controller (rev 02)).
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ce_stats ipackets and opackets members are only used to update
the net_device_stats->[r,t]x_packets counters, so get rid of them.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net_device_stats->rx_packets counter is not getting updated.
This is due to checking a fMP_ADAPTER_LINK_DETECTION flag prior to
updating which is never set.
Solved by using netif_carrier_ok() to test for a link, and removing
the fMP_ADAPTER_LINK_DETECTION flag, which looks to be a broken
mechanism.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removing '_t' from ce_stats_t struct name and renaming et131x_adapter ce_stats member from
'Stats' to 'stats'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes unions, and uses definitions for bit manipulations.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
