The sched_clock_remote() implementation has the following inatomicity
problem on 32bit systems when accessing the remote scd->clock, which
is a 64bit value.
CPU0 CPU1
sched_clock_local() sched_clock_remote(CPU0)
...
remote_clock = scd[CPU0]->clock
read_low32bit(scd[CPU0]->clock)
cmpxchg64(scd->clock,...)
read_high32bit(scd[CPU0]->clock)
While the update of scd->clock is using an atomic64 mechanism, the
readout on the remote cpu is not, which can cause completely bogus
readouts.
It is a quite rare problem, because it requires the update to hit the
narrow race window between the low/high readout and the update must go
across the 32bit boundary.
The resulting misbehaviour is, that CPU1 will see the sched_clock on
CPU1 ~4 seconds ahead of it's own and update CPU1s sched_clock value
to this bogus timestamp. This stays that way due to the clamping
implementation for about 4 seconds until the synchronization with
CLOCK_MONOTONIC undoes the problem.
The issue is hard to observe, because it might only result in a less
accurate SCHED_OTHER timeslicing behaviour. To create observable
damage on realtime scheduling classes, it is necessary that the bogus
update of CPU1 sched_clock happens in the context of an realtime
thread, which then gets charged 4 seconds of RT runtime, which results
in the RT throttler mechanism to trigger and prevent scheduling of RT
tasks for a little less than 4 seconds. So this is quite unlikely as
well.
The issue was quite hard to decode as the reproduction time is between
2 days and 3 weeks and intrusive tracing makes it less likely, but the
following trace recorded with trace_clock=global, which uses
sched_clock_local(), gave the final hint:
<idle>-0 0d..30 400269.477150: hrtimer_cancel: hrtimer=0xf7061e80
<idle>-0 0d..30 400269.477151: hrtimer_start: hrtimer=0xf7061e80 ...
irq/20-S-587 1d..32 400273.772118: sched_wakeup: comm= ... target_cpu=0
<idle>-0 0dN.30 400273.772118: hrtimer_cancel: hrtimer=0xf7061e80
What happens is that CPU0 goes idle and invokes
sched_clock_idle_sleep_event() which invokes sched_clock_local() and
CPU1 runs a remote wakeup for CPU0 at the same time, which invokes
sched_remote_clock(). The time jump gets propagated to CPU0 via
sched_remote_clock() and stays stale on both cores for ~4 seconds.
There are only two other possibilities, which could cause a stale
sched clock:
1) ktime_get() which reads out CLOCK_MONOTONIC returns a sporadic
wrong value.
2) sched_clock() which reads the TSC returns a sporadic wrong value.
#1 can be excluded because sched_clock would continue to increase for
one jiffy and then go stale.
#2 can be excluded because it would not make the clock jump
forward. It would just result in a stale sched_clock for one jiffy.
After quite some brain twisting and finding the same pattern on other
traces, sched_clock_remote() remained the only place which could cause
such a problem and as explained above it's indeed racy on 32bit
systems.
So while on 64bit systems the readout is atomic, we need to verify the
remote readout on 32bit machines. We need to protect the local->clock
readout in sched_clock_remote() on 32bit as well because an NMI could
hit between the low and the high readout, call sched_clock_local() and
modify local->clock.
Thanks to Siegfried Wulsch for bearing with my debug requests and
going through the tedious tasks of running a bunch of reproducer
systems to generate the debug information which let me decode the
issue.
Reported-by: Siegfried Wulsch <Siegfried.Wulsch@rovema.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1304051544160.21884@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
This reverts commit 8761a3dc1f.
There are situations where the destruction path is called
with the bdev->bd_mutex already held, which then deadlocks in
loop_clr_fd(). The normal partition cleanup does a trylock()
on the mutex, but it'd be nice to have a more bullet proof
method in loop. So punt this more involved fix to the next
merge window, and just back out this buggy fix for now.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some versions of pHyp will perform the adjunct partition test before the
ANDCOND test. The result of this is that H_RESOURCE can be returned and
cause the BUG_ON condition to occur. The HPTE is not removed. So add a
check for H_RESOURCE, it is ok if this HPTE is not removed as
pSeries_lpar_hpte_remove is looking for an HPTE to remove and not a
specific HPTE to remove. So it is ok to just move on to the next slot
and try again.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathias Krause says:
====================
a few more info leak fixes in the recvmsg path. The error pattern here
is the protocol specific recvmsg function is missing the msg_namelen
assignment -- either completely or in early exit paths that do not
result in errors in __sys_recvmsg()/sys_recvfrom() and, in turn, make
them call move_addr_to_user(), leaking the then still uninitialized
sockaddr_storage stack variable to userland.
My audit was initiated by a rather coarse fix of the leak that can be
found in the grsecurity patch, putting a penalty on protocols complying
to the rules of recvmsg. So credits for finding the leak in the recvmsg
path in __sys_recvmsg() should go to Brad!
The buggy protocols/subsystems are rather obscure anyway. As a missing
assignment of msg_namelen coupled with a missing filling of msg_name
would only result in garbage -- the leak -- in case userland would care
about that information, i.e. would provide a msg_name pointer. But
obviously current userland does not.
While auditing the code for the above pattern I found a few more
'uninitialized members' kind of leaks related to the msg_name filling.
Those are fixed in this series, too.
I have to admit, I failed to test all of the patches due to missing
hardware, e.g. iucv depends on S390 -- hardware I've no access to :/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code misses to update the msg_namelen member to 0 and therefore
makes net/socket.c leak the local, uninitialized sockaddr_storage
variable to userland -- 128 bytes of kernel stack memory.
Cc: Andy King <acking@vmware.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: George Zhang <georgezhang@vmware.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we received no data on the call to skb_recv_datagram(), i.e.
skb->data is NULL, vmci_transport_dgram_dequeue() will return with 0
without updating msg_namelen leading to net/socket.c leaking the local,
uninitialized sockaddr_storage variable to userland -- 128 bytes of
kernel stack memory.
Fix this by moving the already existing msg_namelen assignment a few
lines above.
Cc: Andy King <acking@vmware.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: George Zhang <georgezhang@vmware.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in set_orig_addr() does not initialize all of the members of
struct sockaddr_tipc when filling the sockaddr info -- namely the union
is only partly filled. This will make recv_msg() and recv_stream() --
the only users of this function -- leak kernel stack memory as the
msg_name member is a local variable in net/socket.c.
Additionally to that both recv_msg() and recv_stream() fail to update
the msg_namelen member to 0 while otherwise returning with 0, i.e.
"success". This is the case for, e.g., non-blocking sockets. This will
lead to a 128 byte kernel stack leak in net/socket.c.
Fix the first issue by initializing the memory of the union with
memset(0). Fix the second one by setting msg_namelen to 0 early as it
will be updated later if we're going to fill the msg_name member.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in rose_recvmsg() does not initialize all of the members of
struct sockaddr_rose/full_sockaddr_rose when filling the sockaddr info.
Nor does it initialize the padding bytes of the structure inserted by
the compiler for alignment. This will lead to leaking uninitialized
kernel stack bytes in net/socket.c.
Fix the issue by initializing the memory used for sockaddr info with
memset(0).
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in llcp_sock_recvmsg() does not initialize all the members of
struct sockaddr_nfc_llcp when filling the sockaddr info. Nor does it
initialize the padding bytes of the structure inserted by the compiler
for alignment.
Also, if the socket is in state LLCP_CLOSED or is shutting down during
receive the msg_namelen member is not updated to 0 while otherwise
returning with 0, i.e. "success". The msg_namelen update is also
missing for stream and seqpacket sockets which don't fill the sockaddr
info.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix the first issue by initializing the memory used for sockaddr info
with memset(0). Fix the second one by setting msg_namelen to 0 early.
It will be updated later if we're going to fill the msg_name member.
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case msg_name is set the sockaddr info gets filled out, as
requested, but the code fails to initialize the padding bytes of
struct sockaddr_ax25 inserted by the compiler for alignment. Also
the sax25_ndigis member does not get assigned, leaking four more
bytes.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix both issues by initializing the memory with memset(0).
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For stream sockets the code misses to update the msg_namelen member
to 0 and therefore makes net/socket.c leak the local, uninitialized
sockaddr_storage variable to userland -- 128 bytes of kernel stack
memory. The msg_namelen update is also missing for datagram sockets
in case the socket is shutting down during receive.
Fix both issues by setting msg_namelen to 0 early. It will be
updated later if we're going to fill the msg_name member.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2TP code for IPv6 fails to initialize the l2tp_conn_id member of
struct sockaddr_l2tpip6 and therefore leaks four bytes kernel stack
in l2tp_ip6_recvmsg() in case msg_name is set.
Initialize l2tp_conn_id with 0 to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about iucv_sock_recvmsg() not filling the msg_name in case it was set.
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about irda_recvmsg_dgram() not filling the msg_name in case it was
set.
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about caif_seqpkt_recvmsg() not filling the msg_name in case it was
set.
Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the socket is in state BT_CONNECT2 and BT_SK_DEFER_SETUP is set in
the flags, sco_sock_recvmsg() returns early with 0 without updating the
possibly set msg_namelen member. This, in turn, leads to a 128 byte
kernel stack leak in net/socket.c.
Fix this by updating msg_namelen in this case. For all other cases it
will be handled in bt_sock_recvmsg().
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RFCOMM_DEFER_SETUP is set in the flags, rfcomm_sock_recvmsg() returns
early with 0 without updating the possibly set msg_namelen member. This,
in turn, leads to a 128 byte kernel stack leak in net/socket.c.
Fix this by updating msg_namelen in this case. For all other cases it
will be handled in bt_sock_stream_recvmsg().
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the socket is already shutting down, bt_sock_recvmsg() returns
with 0 without updating msg_namelen leading to net/socket.c leaking the
local, uninitialized sockaddr_storage variable to userland -- 128 bytes
of kernel stack memory.
Fix this by moving the msg_namelen assignment in front of the shutdown
test.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When msg_namelen is non-zero the sockaddr info gets filled out, as
requested, but the code fails to initialize the padding bytes of struct
sockaddr_ax25 inserted by the compiler for alignment. Additionally the
msg_namelen value is updated to sizeof(struct full_sockaddr_ax25) but is
not always filled up to this size.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix both issues by initializing the memory with memset(0).
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about vcc_recvmsg() not filling the msg_name in case it was set.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fix from Gleb Natapov:
"Bugfix for the regression introduced by commit c300aa64ddf5"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Allow cross page reads and writes from cached translations.
Pull x86 fixes from Peter Anvin:
"Two quite small fixes: one a build problem, and the other fixes
seccomp filters on x32."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix rebuild with EFI_STUB enabled
x86: remove the x32 syscall bitmask from syscall_get_nr()
Interrupt handlers are always invoked with interrupts disabled, so
remove all uses of the deprecated IRQF_DISABLED flag.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux has expected that interrupt handlers are executed with local
interrupts disabled for a while now, so ensure that this is the case on
Alpha even for non-device interrupts such as IPIs.
Without this patch, secondary boot results in the following backtrace:
warning: at kernel/softirq.c:139 __local_bh_enable+0xb8/0xd0()
trace:
__local_bh_enable+0xb8/0xd0
irq_enter+0x74/0xa0
scheduler_ipi+0x50/0x100
handle_ipi+0x84/0x260
do_entint+0x1ac/0x2e0
irq_exit+0x60/0xa0
handle_irq+0x98/0x100
do_entint+0x2c8/0x2e0
ret_from_sys_call+0x0/0x10
load_balance+0x3e4/0x870
cpu_idle+0x24/0x80
rcu_eqs_enter_common.isra.38+0x0/0x120
cpu_idle+0x40/0x80
rest_init+0xc0/0xe0
_stext+0x1c/0x20
A similar dump occurs if you try to reboot using magic-sysrq.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to all of the goodness being packed into today's kernels, the
resulting image isn't as slim as it once was.
In light of this, don't pass -msmall-data to gcc, which otherwise results
in link failures due to impossible relocations when compiling anything but
the most trivial configurations.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Thorsten Kranzkowski <dl8bcu@dl8bcu.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a NULL pointer dereference at boot on UP1500.
Cc: stable@vger.kernel.org
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetja Rediske found that if the host receives an ICMPv6 redirect message
after sending a SYN+ACK, the connection will be reset.
He bisected it down to 093d04d (ipv6: Change skb->data before using
icmpv6_notify() to propagate redirect), but the origin of the bug comes
from ec18d9a26 (ipv6: Add redirect support to all protocol icmp error
handlers.). The bug simply did not trigger prior to 093d04d, because
skb->data did not point to the inner IP header and thus icmpv6_notify
did not call the correct err_handler.
This patch adds the missing "goto out;" in tcp_v6_err. After receiving
an ICMPv6 Redirect, we should not continue processing the ICMP in
tcp_v6_err, as this may trigger the removal of request-socks or setting
sk_err(_soft).
Reported-by: Tetja Rediske <tetja@tetja.de>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for kvm_gfn_to_hva_cache_init functions for
reads and writes that will cross a page. If the range falls within
the same memslot, then this will be a fast operation. If the range
is split between two memslots, then the slower kvm_read_guest and
kvm_write_guest are used.
Tested: Test against kvm_clock unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
This patch fixes the following bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90
Call Trace:
[<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80
[<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0
[<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90
[<ffffffff8132b0f4>] device_del+0x44/0x1d0
[<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas]
[<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas]
[<ffffffff8107ac7c>] process_one_work+0x16c/0x350
[<ffffffff8107d84a>] worker_thread+0x17a/0x410
[<ffffffff81081b76>] kthread+0x96/0xa0
[<ffffffff81464944>] kernel_thread_helper+0x4/0x10
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
No locks should be held when calling scsi_adjust_queue_depth
so drop the lock in slave_configure prior to calling it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.
Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.
Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reinitialize resource queue prior to freeing resource entries to ensure they
are not referenced. This fixes an issue with target_destoy accessing memory
after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The abort command issued by ipr_cancel_op() is being added to the wrong
HRRQ free queue after the command returns. Fix it by using the HRRQ
pointer in the ipr command struct itself.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a reference count bug in the SCSI tape driver which can be
reproduced with the following:
* Boot with slub_debug=FZPU, tape drive attached
* echo 1 > /sys/devices/... tape device pci path .../remove
* Wait for device removal
* echo 1 > /sys/kernel/slab/blkdev_queue/validate
* Slub debug complains about corrupted poison pattern
In commit 523e1d39 (block: make gendisk hold a reference to its queue)
add_disk() and disk_release() were modified to get/put an additional
reference on a disk queue to fix a reference counting discrepency
between bdev release and SCSI device removal. The ST driver never
calls add_disk(), so this commit introduced an extra kref put when the
ST driver frees its struct gendisk.
Attempts were made to fix this bug at the block level [1] but later
abandoned due to floppy driver issues [2].
[1] https://lkml.org/lkml/2012/8/27/354
[2] https://lkml.org/lkml/2012/9/22/113
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In fact the disc_resp buffer will be overwrite by smp response, so we never
found this typo, correct it by using the right one.
Signed-off-by: John Gong <john_gong@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Loading ipr modules failed(-22) with msi-x enabled adapter. In ipr_test_msi(),
We need to pass the first vector of msix vectors instead of using pdev->irq
to request_irq() when adapter enables msix feature.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
cache target when the device being cached is not itself wrapped with
device-mapper.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LUeu
-----END PGP SIGNATURE-----
Merge tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair Kergon:
"A pair of patches to fix the writethrough mode of the device-mapper
cache target when the device being cached is not itself wrapped with
device-mapper."
* tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm cache: reduce bio front_pad size in writeback mode
dm cache: fix writes to cache device in writethrough mode
ASPM
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
kexec
PCI: Don't try to disable Bus Master on disconnected PCI devices
Platform ROM images
PCI: Add PCI ROM helper for platform-provided ROM images
nouveau: Attempt to use platform-provided ROM image
radeon: Attempt to use platform-provided ROM image
Hotplug
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI/PM: Disable runtime PM of PCIe ports
EISA
EISA/PCI: Fix bus res reference
EISA/PCI: Init EISA early, before PNP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gIGr
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"PCI updates for v3.9:
ASPM
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
kexec
PCI: Don't try to disable Bus Master on disconnected PCI devices
Platform ROM images
PCI: Add PCI ROM helper for platform-provided ROM images
nouveau: Attempt to use platform-provided ROM image
radeon: Attempt to use platform-provided ROM image
Hotplug
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI/PM: Disable runtime PM of PCIe ports
EISA
EISA/PCI: Fix bus res reference
EISA/PCI: Init EISA early, before PNP"
* tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Disable runtime PM of PCIe ports
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI: Don't try to disable Bus Master on disconnected PCI devices
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
radeon: Attempt to use platform-provided ROM image
nouveau: Attempt to use platform-provided ROM image
EISA/PCI: Init EISA early, before PNP
EISA/PCI: Fix bus res reference
PCI: Add PCI ROM helper for platform-provided ROM images
Pull networking fixes from David Miller:
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
If the call to rpciod_up() fails, we currently leak a reference to the
struct rpc_xprt.
As part of the fix, we also remove the redundant check for xprt!=NULL.
This is already taken care of by the callers.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
eboot.o and efi_stub_$(BITS).o didn't get added to "targets", and hence
their .cmd files don't get included by the build machinery, leading to
the files always getting rebuilt.
Rather than adding the two files individually, take the opportunity and
add $(VMLINUX_OBJS) to "targets" instead, thus allowing the assignment
at the top of the file to be shrunk quite a bit.
At the same time, remove a pointless flags override line - the variable
assigned to was misspelled anyway, and the options added are
meaningless for assembly sources.
[ hpa: the patch is not minimal, but I am taking it for -urgent anyway
since the excess impact of the patch seems to be small enough. ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/515C5D2502000078000CA6AD@nat28.tlf.novell.com
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
