SMU takes clock limits in Mhz units. socclk and fclk were
using 10 khz units in some cases. Switch to Mhz units.
Fixes higher than required SoC clocks.
Fixes: 97cf32996c ("drm/amd/pm: Removed fixed clock in auto mode DPM")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why & How]
Make dcn315 base its clock table off dcfclk rather than fclk.
This change also adds some sanity checking to make sure an
empty pmfw table does not result in invalid dal clocks.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Work around to try to wake unresponsive DP sinks may need to be adjusted
for certain sinks.
[How]
Add options to disable work around or adjust time spent trying to wake
unresponsive DPRX.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When waking from low-power states, a DP sink may remain unresponsive to
AUX transactions.
[How]
Try to toggle DPCD SET_POWER register repeatedly (up to a maximum
timeout value) until DP sink becomes responsive.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC Power down code has been moved from dcn31_init_hw into init_pipes()
Need to remove it from dcn10_init_hw() as well to avoid duplicated action
on dcn1.x/2.x
[How]
Remove DSC power down code from dcn10_init_hw()
Fixes: 8fa6f4c571 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP")
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once DSC slice cannot fit pixel clock, we incorrectly
reset min slices to 0 and allow max slice to operate,
even when max slice itself cannot fit the pixel clock
properly.
[How]
Change the sequence such that we correctly determine
DSC is not possible when both min slices and max
slices cannot fit pixel clock per slice.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some video card has more than one vcn instance, passing 0 to
vcn_v3_0_pause_dpg_mode is incorrect.
Error msg:
Register(1) [mmUVD_POWER_STATUS] failed to reach value
0x00000001 != 0x00000002
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: tiancyin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
For VCN FW to detect ASIC type, in order to use different mailbox registers.
V2: simplify codes and fix format issue.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Acked-by Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While bridge/panel detection was initially relying on the usual
port/ports-based of graph detection, it was recently changed to
perform the lookup on any child node that is not port/ports
instead when such a node is available, with no fallback on the
usual way.
This results in breaking detection when a child node is present
but does not contain any panel or bridge node, even when the
usual port/ports-based of graph is there.
In order to support both situations properly, this commit reworks
the logic to try both options and not just one of the two: it will
only return -EPROBE_DEFER when both have failed.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: 80253168db ("drm: of: Lookup if child node has panel or bridge")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329132732.628474-1-paul.kocialkowski@bootlin.com
Pull xen updates from Juergen Gross:
- A bunch of minor cleanups
- A fix for kexec in Xen dom0 when executed on a high cpu number
- A fix for resuming after suspend of a Xen guest with assigned PCI
devices
- A fix for a crash due to not disabled preemption when resuming as Xen
dom0
* tag 'for-linus-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: fix is_xen_pmu()
xen: don't hang when resuming PCI device
arch:x86:xen: Remove unnecessary assignment in xen_apic_read()
xen/grant-table: remove readonly parameter from functions
xen/grant-table: remove gnttab_*transfer*() functions
drivers/xen: use helper macro __ATTR_RW
x86/xen: Fix kerneldoc warning
xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
xen: use time_is_before_eq_jiffies() instead of open coding it
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
Pull drm fixes from Dave Airlie:
"Some fixes were queued up in and in light of the fbdev regressions,
I've pulled those in as well.
core:
- Make audio and color plane support checking only happen when a CEA
extension block is found.
- Small selftest fix.
fbdev:
- two regressions fixes from speedup patches.
ttm:
- Fix a small regression from ttm_resource_fini()
i915:
- Reject unsupported TMDS rates on ICL+
- Treat SAGV block time 0 as SAGV disabled
- Fix PSF GV point mask when SAGV is not possible
- Fix renamed INTEL_INFO->media.arch/ver field"
* tag 'drm-next-2022-03-25' of git://anongit.freedesktop.org/drm/drm:
fbdev: Fix cfb_imageblit() for arbitrary image widths
fbdev: Fix sys_imageblit() for arbitrary image widths
drm/edid: fix CEA extension byte #3 parsing
drm/edid: check basic audio support on CEA extension block
drm/i915: Fix renamed struct field
drm/i915: Fix PSF GV point mask when SAGV is not possible
drm/i915: Treat SAGV block time 0 as SAGV disabled
drm/i915: Reject unsupported TMDS rates on ICL+
drm/selftest: plane_helper: Put test structures in static storage
drm/ttm: Fix a kernel oops due to an invalid read
Pull Kbuild update for C11 language base from Masahiro Yamada:
"Kbuild -std=gnu11 updates for v5.18
Linus pointed out the benefits of C99 some years ago, especially
variable declarations in loops [1]. At that time, we were not ready
for the migration due to old compilers.
Recently, Jakob Koschel reported a bug in list_for_each_entry(), which
leaks the invalid pointer out of the loop [2]. In the discussion, we
agreed that the time had come. Now that GCC 5.1 is the minimum
compiler version, there is nothing to prevent us from going to
-std=gnu99, or even straight to -std=gnu11.
Discussions for a better list iterator implementation are ongoing, but
this patch set must land first"
[1] https://lore.kernel.org/all/CAHk-=wgr12JkKmRd21qh-se-_Gs69kbPgR9x4C+Es-yJV2GLkA@mail.gmail.com/
[2] https://lore.kernel.org/lkml/86C4CE7D-6D93-456B-AA82-F8ADEACA40B7@gmail.com/
* tag 'kbuild-gnu11-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Kbuild: use -std=gnu11 for KBUILD_USERCFLAGS
Kbuild: move to -std=gnu11
Kbuild: use -Wdeclaration-after-statement
Kbuild: add -Wno-shift-negative-value where -Wextra is used
As the kmalloc_array() may return null, the 'event_waiters[i].wait' would lead to null-pointer dereference.
Therefore, it is better to check the return value of kmalloc_array() to avoid this confusion.
Signed-off-by: QintaoShen <unSimple1993@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Recently introduced commit 158a05a0b8 ("drm/amdgpu: Add
use_xgmi_p2p module parameter") did not update XGMI iolinks
when use_xgmi_p2p is disabled. Add fix to not create XGMI
iolinks in KFD topology when this parameter is disabled.
Fixes: 158a05a0b8 ("drm/amdgpu: Add use_xgmi_p2p module parameter")
Signed-off-by: Divya Shikre <DivyaUday.Shikre@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Compute-only GPUs have more than 8 VMIDs allocated to KFD. Fix
this by passing correct number of VMIDs to HWS
v2: squash in warning fix (Alex)
Signed-off-by: Tushar Patel <tushar.patel@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we enter FREESYNC_STATE_VIDEO, we want to use the extra vblank
portion to enter zstate if possible.
[how]
When we enter freesync, a full update is triggered and the new vtotal
with extra lines is passed to dml in a stream update. The time gained
from extra vblank lines is calculated in microseconds. We allow zstate
entry if the time gained is greater than 5 ms, which is the current
policy. Furthermore, an optimized value for min_dst_y_next_start is
calculated and written to its register. When exiting freesync, another
full update is triggered and default values are restored.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
