With the original PPGTT implementation if the number of PDPs was not a
power of two, the number of pages for the page tables would end up being
rounded up. The code actually had a bug here afaict, but this is a
theoretical bug as I don't believe this can actually occur with the
current code/HW..
With the rework of the page table allocations, there is no longer a
distinction between number of page table pages, and number of page
directory entries. To avoid confusion, kill the redundant (and newer)
struct member.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll need this when we merge PC8 and Runtime PM: the PC8
enable/disable functions need that lock.
Also, it's good practice to not hold a lock for longer than strictly
needed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can be expanded up on to include all sorts of things (HDMI infoframe
data, more DP status, etc). Should be useful for bug reports to get a
baseline on the display config and info.
v2: use seq_putc (Rodrigo)
describe mode field names (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A check of rps/rc6 state after i915_reset determined that the ring
MAX_IDLE registers were returned to their hardware defaults and that
the GEN6_PMIMR register was set to mask all interrupts. This change
restores those values to their pre-reset states by re-initializing
rps/rc6 in i915_reset. A full re-initialization was opted for versus
a targeted set of restore operations for simplicity and maintain-
ability. Note that the re-initialization is not done for Ironlake,
due to a past comment that it causes problems.
Also updated the rps initialization sequence to preserve existing
min/max values in the case of a re-init. We assume the values were
validated upon being set and do not do further range checking. The
debugfs interface for changing min/max was updated with range
checking to ensure this condition (already present in sysfs
interface).
v2: fix rps logging to output hw_max and hw_min, not rps.max_delay
and rps.min_delay which don't strictly represent hardware limits.
Add igt testcase to signed-off-by section.
Testcase: igt/pm_rps/reset
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a few new debugfs files which allow changing the watermark memory
latency values during runtime. This can be used to determine the if the
original BIOS provided latency values are no good.
v2: Drop superfluous plane name from output
Take modeset locks around the latency value read/write
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This debugfs interface will allow intel-gpu-tools test case
to verify if screen has been updated properly on cases like PSR.
v2: Accepted all Daniel's suggestions:
* grab modeset lock
* loop over connector and check DPMS on
* return errors
* use _eDP1 suffix for easy future extension
* don't cache crc_supported neither latest crc
* return crc as a full array and read it at once with aux.
* use 0 to turn TEST_SINK off.
* split the drm_helpers definitions in another patch.
v3: Accepted 2 Damien's suggestion: remove h from printf hexa
and return ENODEV when eDP not present instead of EAGAIN.
v4: Accepted 2 Jani' s suggestion: 1 path for unlock and remove
_retry from aux read.
v5: removing last missing useless _retry (by Damien)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because whatever.*
* This should contain a fairly long list of issues and still
unresolved resgressions, but I didn't really get a vote.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure anyone cares about this information. I suppose most people
would just look at /proc/interrupts instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many of the fields from Gen6 have gone away for vlv. Strip all those
fields that are not relevent and try to update fields that we care
about. This patch give information about current RP & RC status and
individual Wells.
v2: Move Render & Media Well status to separate lines (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My OCD just couldn't let this slide. Spotted while reviewing Ville's
patch to only flip planes when we have FBC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Art, we don't have a way to read back the state reliably at
runtime, through the control reg or the mailbox, at least not without risking
disabling it again. So drop the readout and checking on BDW.
v2: drop TODO comment (Paulo)
move POSTING_READ of control reg under HSW branch in disable (Paulo)
always report IPS as enabled on BDW (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=71906
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since get_pid_task() grabs a reference on the task_struct, we have to drop the
refcount after reading that task's comm name. Use pid_task() with RCU instead.
Also, avoid directly reading like pid_task()->comm because
pid_task() will return NULL if the task have already exit()ed.
This patch fixes both problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dump the aliasing PPGTT with it. The aliasing PPGTT should actually
always be empty.
TODO: Broadwell. Since we don't yet use full PPGTT on Broadwell, not
having the dumper is okay.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The whole file is wrapped around in #if defined(CONFIG_DEBUG_FS) anyway,
so skip the file at the build level already.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case of error, the function debugfs_create_file() returns NULL
pointer not ERR_PTR() if debugfs is enabled. The IS_ERR() test in
the return value check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are needed when we cat the debugfs and sysfs files.
V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Forcewake counts for valleyview are not exposed throgh DebugFS.
Exposing with this change.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added power well arguments to all the force wake routines
to help us individually control power well based on the
scenario.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the removed forcewake hack and drop one
spurious hunk Jesse noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a debugfs entry showing the use-count for all power domains of each
power well.
v3: address comments from Paulo:
- simplify power_domain_str() by using a switch table
- move power_well::domain_count to power_domains
- WARN_ON decrementing a 0 refcount
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many tests call this ad naseum now (in an infinite loop, very often).
It clutters the logs. Actually, I'd rather drop it completely...
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gcc complains that:
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘display_crc_ctl_write’:
drivers/gpu/drm/i915/i915_debugfs.c:2393:2: warning: ‘val’ may be used uninitialized in this function [-Wuninitialized]
drivers/gpu/drm/i915/i915_debugfs.c:2350:6: note: ‘val’ was declared here
but it can't see that we're going to use val only in the success case.
So shut it up.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't init the lock nor set up all the other state. And it doesn't
make sense anyway.
This appeases lockdep when running the igt/drv_debugfs_reader test.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
It's not so much that the information is terribly useful, but rather
that the gen6/7 information is completely useless.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the gen8 debugfs stuff I wasn't too lazy to update. We'll need more
later, I am certain.
v2: Fix up the register name in the debugfs output as suggested by
Paulo.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
The RPS register writing routines use the current value of min/max to
set certain limits and interrupt gating. If we set those afterwards, we
risk setting up the hw incorrectly and losing power management events,
and worse, trigger some internal assertions.
Reorder the calling sequences to be correct, and remove the then
unrequired clamping from inside set_rps(). And for a bonus, fix the bug
of calling gen6_set_rps() from Valleyview.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The max frequency reporting is not correct. But there is already an existing
valleyview_rps_max_freq and valleyview_rps_min_freq to get the
frequency. Use that for i915_cur_delayinfo.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll be looking at more than just mem_freq from dev_priv, so
just pass the whole thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that DP port CRCs are stable, we can use it for generic CRC tests.
Yay, the auto CRC source should now work everywhere!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They've moved the DC balance reset bit around. Again I don't think we
need it, but better safe than sorry and maybe HDMI port CRC will prove
useful for checking infoframes or hdmi audio.
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gmch platforms the normal pipe source CRC registers don't work for
DP and TV encoders. And on newer platforms the single pipe CRC has
been replaced by a set of CRC at different stages in the platform.
Now most of our userspace tests don't care one bit about the exact
CRC, they simply want something that reflects any changes on the
screen. Hence add a new auto target for platform agnostic tests to
use.
v2: Pass back the adjusted source so that it can be shown in debugfs.
v3: I seem to be unable to get a stable CRC for DP ports. So let's
just disable them for now when using the auto mode. Note that
testcases need to be restructured so that they can dynamically skip
connectors. They also first need to set up the desired mode
configuration, since otherwise the auto mode won't do the right thing.
v4: Don't leak the modeset mutex on error paths.
v5: Spelling fix for the i9xx auto_source function.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel pointed out that it was hard to get anything lockless to work
correctly, so don't even try for this non critical piece of code and
just use a spin lock.
v2: Make intel_pipe_crc->opened a bool
v3: Use assert_spin_locked() instead of a comment (Daniel Vetter)
v4: Use spin_lock_irq() in the debugfs functions (they can only be
called from process context),
Use spin_lock() in the pipe_crc_update() function that can only be
called from an interrupt handler,
Use wait_event_interruptible_lock_irq() when waiting for data in the
cicular buffer to ensure proper locking around the condition we are
waiting for. (Daniel Vetter)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Really simple, and we don't even have working frame numbers.
v2: Actually enable it ...
v3: Review from Ville:
- Unconditionally enable the border in the CRC checksum for
consistency with gen3+.
- Handle the "none" source to be able to disable the CRC machinery
again.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-gen5 and vlv we can't use the pipe source when TV-out or a DP
port is connected to the pipe. Hence we need to expose new CRC
sources.
Also simplify the existing pipe source platform code a bit by
rejecting all unhandled sources by default.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hw designers decided to change the CRC registers and coalesce them all
into one. Otherwise nothing changed. I've opted for a new hsw_ version
to grab the crc sample since hsw+1 will have the same crc registers,
but different interrupt source registers. So this little helper
function will come handy there.
Also refactor the display error handler with a neat pipe loop.
v2: Use for_each_pipe.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've set up all files, but removed only those for which we have a
pipe. Which leaves the one for pipe C on machines with less than 2
pipes, breaking module reload.
v2: We can't get at the drm device this early (wtf), so just register
all the files and also remove them all again.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This avoids a spurious spurious interrupt warning.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We enable the interrupt unconditionally and only control it
through the enable bit in the CRC control register.
v2: Extract per-platform helpers to compute the register values.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Failed to properly test this.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We not only want const strings, but a const array of them. Reported by
checkpatch.pl
Cc: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's time to declare them ready. Unleash the beast.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't really make sense to have two processes dequeueing the CRC
values at the same time. Forbid that usage.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
seq_file is not quite the right interface for these ones. We have a
circular buffer with a new entry per vblank on one side and a process
wanting to dequeue the CRC with a read().
It's quite racy to wait for vblank in user land and then try to read a
pipe_crc file, sometimes the CRC interrupt hasn't been fired and we end
up with an EOF.
So, let's have the read on the pipe_crc file block until the interrupt
gives us a new entry. At that point we can wake the reading process.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following commit needs drm_add_fake_info_node() higher in the file to
avoid having a forward declaration. Move this helper near the top of the
file.
This also makes the next commit diff a bit easier to review.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the same spirit than:
drm/i915: Generalize the CRC command format for future work
Let's move from writing 'A plane1' to 'pipe A plane1' to
i915_pipe_crc_ctl. This will allow us to extend the interface to
transcoders or DDIs in the future.
Let's rename the CRC control file to be more generic.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's move from writing 'A plane1' to 'pipe A plane1' to
i915_pipe_crc_ctl. This will allow us to extend the interface to
transcoders or DDIs in the future.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we don't eat that memory when not needed.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we don't read out stale CRCs from a previous run left in the buffer.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can have some init/fini code on those transitions.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are a few good properties to a circular buffer, for instance it
has a number of entries (before we were always dumping the full buffer).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note the "return -ENODEV;" in pipe_crc_set_source(). The ctl file is
disabled until the end of the series to be able to do incremental
improvements.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are several points in the display pipeline where CRCs can be
computed on the bits flowing there. For instance, it's usually possible
to compute the CRCs of the primary plane, the sprite plane or the CRCs
of the bits after the panel fitter (collectively called pipe CRCs).
v2: Quite a bit of rework here and there (Damien)
Signed-off-by: Shuang He <shuang.he@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix intermediate compile file reported by Wu Fengguang's
kernel builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabling rps (turbo setup) was put in a work queue because it may
take quite awhile. This change flushes the work queue to initialize
rps values before use by sysfs or debugfs. Specifically,
rps.delayed_resume_work is flushed before using rps.hw_max,
rps.max_delay, rps.min_delay, or rps.cur_delay.
This change fixes a problem in sysfs where show functions using
uninitialized values show incorrect values and store functions
using uninitialized values in range checks incorrectly fail to
store valid input values. This change also addresses similar use
before initialized problems in debugfs.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for igt test case.
v2: remove trailing spaces and fix conflicts
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet:
- make it comipile
- s/IS_HASWELL/HAS_PSR/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we switched to always using a timeout in conjunction with
wait_seqno, we lost the ability to detect missed interrupts. Since, we
have had issues with interrupts on a number of generations, and they are
required to be delivered in a timely fashion for a smooth UX, it is
important that we do log errors found in the wild and prevent the
display stalling for upwards of 1s every time the seqno interrupt is
missed.
Rather than continue to fix up the timeouts to work around the interface
impedence in wait_event_*(), open code the combination of
wait_event[_interruptible][_timeout], and use the exposed timer to
poll for seqno should we detect a lost interrupt.
v2: In order to satisfy the debug requirement of logging missed
interrupts with the real world requirments of making machines work even
if interrupts are hosed, we revert to polling after detecting a missed
interrupt.
v3: Throw in a debugfs interface to simulate broken hw not reporting
interrupts.
v4: s/EGAIN/EAGAIN/ (Imre)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Don't use the struct typedef in new code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On both Ivybridge and Haswell, row remapping information is saved and
restored with context. This means, we never actually properly supported
the l3 remapping because our sysfs interface is asynchronous (and not
tied to any context), and the known faulty HW would be reused by the
next context to run.
Not that due to the asynchronous nature of the sysfs entry, there is no
point modifying the registers for the existing context. Instead we set a
flag for all contexts to load the correct remapping information on the
next run. Interested clients can use debugfs to determine whether or not
the row has been remapped.
One could propose at this point that we just do the remapping in the
kernel. I guess since we have to maintain the sysfs interface anyway,
I'm not sure how useful it is, and I do like keeping the policy in
userspace; (it wasn't my original decision to make the
interface the way it is, so I'm not attached).
v2: Force a context switch when we have a remap on the next switch.
(Ville)
Don't let userspace use the interface with disabled contexts.
v3: Don't force a context switch, just let it nop
Improper context slice remap initialization, 1<<1 instead of 1<<i, but I
rewrote it to avoid a second round of confusion.
Error print moved to error path (All Ville)
Added a comment on why the slice remap initialization happens.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have implemented this patch before without creating a separate list
(I'm having trouble finding the links, but the messages ids are:
<1364942743-6041-2-git-send-email-ben@bwidawsk.net>
<1365118914-15753-9-git-send-email-ben@bwidawsk.net>)
However, the code is much simpler to just use a list and it makes the
code from the next patch a lot more pretty.
As you'll see in the next patch, the reason for this is to be able to
specify when a context needs to get L3 remapping. More details there.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sadly, this isn't the first time we've done this:
http://lists.freedesktop.org/archives/intel-gfx/2013-June/029065.html
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It can be useful to compare at times the current vs requested frequency
of the GPU, so provide the contents of RPNSWREQ alonside CAGF.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't like seeing signed seqnos. Make them unsigned.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it print the value of the variables on the PC8 struct.
v2: Update to recent renames and add the new fields.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB and IVB, there's an MSR (also exposed through MCHBAR) we can use
to read out the amount of energy used over time. Expose this in sysfs
to make it easy to do power comparisons with different configurations.
If the platform supports it, the file will show up under the
drm/card0/power subdirectory of the PCI device in sysfs as gt_energy_uJ.
The value in the file is a running total of energy (in microjoules)
consumed by the graphics device.
v2: move to sysfs (Ben, Daniel)
expose a simple value (Chris)
drop unrelated hunk (Ben)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3: by Ben
Tied it into existing rc6 sysfs entries and named that a more generic
"power attrs." Fixed rebase conflicts.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
v4: Since RAPL is a real driver that already exists to serve power
monitoring, place our entry in debugfs. This gives me a fallback
location for systems that do not expose it otherwise.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To convert the execbuf code over to use vmas natively we need to
shuffle the exec_list a bit. This patch here just prepares things with
the debugfs code, which also uses the old exec_list list_head, newly
called obj_exec_link.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Split out from Ben's big patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The display engine has unique coherency rules such that it requires
special handling to ensure that all writes to cursors, scanouts and
sprites are clflushed. This patch introduces the infrastructure to
simply track when an object is being accessed by the display engine.
v2: Explain the is_pin_display() magic as the sources for obj->pin_count
and their individual rules is not obvious. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was curious as to what objects were currently allocated from stolen
memory, and so exported it from debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
formerly: "drm/i915: Create VMAs (part 5) - move mm_list"
The mm_list is used for the active/inactive LRUs. Since those LRUs are
per address space, the link should be per VMx .
Because we'll only ever have 1 VMA before this point, it's not incorrect
to defer this change until this point in the patch series, and doing it
here makes the change much easier to understand.
Shamelessly manipulated out of Daniel:
"active/inactive stuff is used by eviction when we run out of address
space, so needs to be per-vma and per-address space. Bound/unbound otoh
is used by the shrinker which only cares about the amount of memory used
and not one bit about in which address space this memory is all used in.
Of course to actual kick out an object we need to unbind it from every
address space, but for that we have the per-object list of vmas."
v2: only bump GGTT LRU in i915_gem_object_set_to_gtt_domain (Chris)
v3: Moved earlier in the series
v4: Add dropped message from v3
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Frob patch to apply and use vma->node.size directly as
discused with Ben. Also drop a needles BUG_ON before move_to_inactive,
the function itself has the same check.]
[danvet 2nd: Rebase on top of the lost "drm/i915: Cleanup more of VMA
in destroy", specifically unlink the vma from the mm_list in
vma_unbind (to keep it symmetric with bind_to_vm) instead of
vma_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/i915_debugfs.c:2136:3: warning: symbol
'i915_debugfs_files' was not declared. Should it be static?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As alluded to in several patches, and it will be reiterated later... A
VMA is an abstraction for a GEM BO bound into an address space.
Therefore it stands to reason, that the existing bind, and unbind are
the ones which will be the most impacted. This patch implements this,
and updates all callers which weren't already updated in the series
(because it was too messy).
This patch represents the bulk of an earlier, larger patch. I've pulled
out a bunch of things by the request of Daniel. The history is preserved
for posterity with the email convention of ">" One big change from the
original patch aside from a bunch of cropping is I've created an
i915_vma_unbind() function. That is because we always have the VMA
anyway, and doing an extra lookup is useful. There is a caveat, we
retain an i915_gem_object_ggtt_unbind, for the global cases which might
not talk in VMAs.
> drm/i915: plumb VM into object operations
>
> This patch was formerly known as:
> "drm/i915: Create VMAs (part 3) - plumbing"
>
> This patch adds a VM argument, bind/unbind, and the object
> offset/size/color getters/setters. It preserves the old ggtt helper
> functions because things still need, and will continue to need them.
>
> Some code will still need to be ported over after this.
>
> v2: Fix purge to pick an object and unbind all vmas
> This was doable because of the global bound list change.
>
> v3: With the commit to actually pin/unpin pages in place, there is no
> longer a need to check if unbind succeeded before calling put_pages().
> Make put_pages only BUG() after checking pin count.
>
> v4: Rebased on top of the new hangcheck work by Mika
> plumbed eb_destroy also
> Many checkpatch related fixes
>
> v5: Very large rebase
>
> v6:
> Change BUG_ON to WARN_ON (Daniel)
> Rename vm to ggtt in preallocate stolen, since it is always ggtt when
> dealing with stolen memory. (Daniel)
> list_for_each will short-circuit already (Daniel)
> remove superflous space (Daniel)
> Use per object list of vmas (Daniel)
> Make obj_bound_any() use obj_bound for each vm (Ben)
> s/bind_to_gtt/bind_to_vm/ (Ben)
>
> Fixed up the inactive shrinker. As Daniel noticed the code could
> potentially count the same object multiple times. While it's not
> possible in the current case, since 1 object can only ever be bound into
> 1 address space thus far - we may as well try to get something more
> future proof in place now. With a prep patch before this to switch over
> to using the bound list + inactive check, we're now able to carry that
> forward for every address space an object is bound into.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Rebase on top of the loss of "drm/i915: Cleanup more of VMA
in destroy".]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it aware of which domain it is bound into GGTT, or PPGTT.
While modifying the function, add a global gtt flag to the object
description. Global is more interesting than aliasing since aliasing is
the default.
v2: Access VMA directly for start/size instead of helpers (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With an upcoming change to bind, to make checkpatch happy and keep the
code clean, we need to rework this code a bit.
This should have no functional impact.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add the newline Chris requested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost invariably the reason why FBC cannot be turned on is the same
every time (disabled via parameter, too many pipes, pipe too large etc)
as modesetting and framebuffer configuration changes less frequently
than trying to enable FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The TRACE_EVENT_CONDITION is supposed to generate more efficient code
than if (cond) trace(), which is what we are currently using inside the
register access functions.
v2: Rebase onto uncore
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.
v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: prefer seq_puts to seq_printf detected by Paulo Zanoni.
v3: PSR is disabled by default. Without userspace ready it
will cause regression for kde and xdm users
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding support for PSR Status, PSR entry counter and performance counters.
Heavily based on initial work from Shobhit.
v2: Fix PSR Status Link bits by Paulo Zanoni.
v3: Prefer seq_puts to seq_printf by Paulo Zanoni.
v4: Fix identation by Paulo Zanoni.
v5: Return earlier if it isn't Haswell in order to avoid reading non-existing
registers - by Paulo Zanoni.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shamelessly manipulated out of Daniel :-)
"When moving the lists around explain that the active/inactive stuff is
used by eviction when we run out of address space, so needs to be
per-vma and per-address space. Bound/unbound otoh is used by the
shrinker which only cares about the amount of memory used and not one
bit about in which address space this memory is all used in. Of course
to actual kick out an object we need to unbind it from every address
space, but for that we have the per-object list of vmas."
v2: Leave the bound list as a global one. (Chris, indirectly)
v3: Rebased with no i915_gtt_vm. In most places I added a new *vm local,
since it will eventually be replaces by a vm argument.
Put comment back inline, since it no longer makes sense to do otherwise.
v4: Rebased on hangcheck/error state movement
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GTT and PPGTT can be thought of more generally as GPU address
spaces. Many of their actions (insert entries), state (LRU lists), and
many of their characteristics (size) can be shared. Do that.
The change itself doesn't actually impact most of the VMA/VM rework
coming up, it just fits in with the grand scheme of abstracting the GPU
VM operations. GGTT will usually be a special case where we either know
an object must be in the GGTT (dislay engine, workarounds, etc.).
The scratch page is left as part of the VM (even though it's currently
shared with the ppgtt code) because in the future when we have Full
PPGTT, I intend to create a separate scratch page for each.
v2: Drop usage of i915_gtt_vm (Daniel)
Make cleanup also part of the parent class (Ben)
Modified commit msg
Rebased
v3: Properly share scratch page (Imre)
Finish commit message (Daniel, Imre)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make users life a little easier figuring out what they have on their
system.
Ideally, I'd really like to report LLC size, but it turned out to be a
bit of a pain. Maybe I'll revisit it in the future.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move error state generation and stringification to it's
own compilation unit. Sysfs also uses this so it can't be
under CONFIG_DEBUG_FS
This fixes a regression introduced in
commit ef86ddced7
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu Jun 6 17:38:54 2013 +0300
drm/i915: add error_state sysfs entry
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66814
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least for the common cases where we only need special file
operations. The forcewake file is still rather more special.
v2: Fix up the debugfs unregister code.
v3: Actually squash in the right fixup.
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make function for struct i915_error_state_buf initialization
and export it, for sysfs and debugfs.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for sysfs error state access,
export ref error state ref counting interface.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for accessing error state from sysfs, export
error state to string conversion function. Also tuck buffer
error handling inside the function.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Damien's FBC_CHIP_DEFAULT no fbc
reason.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caught with checkpatch.pl.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When running on my snb machine, recent kernels display successively:
[drm:intel_update_fbc], fbc set to per-chip default
[drm:intel_update_fbc], fbc disabled per module param
But no module param is set. This happens because the check for the
module parameter uses a variable that has been overridden inside the
"per-chip default" code.
Fix up the logic and add another reason for the FBC to the be disabled.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So it appears that I have encountered some bogosity when trying to call
i915_error_printf() with many arguments from print_error_buffers(). The
symptom is that the vsnprintf parser tries to interpret an integer arg
as a character string, the resulting OOPS indicating stack corruption.
Replacing the single call with its 13 format specifiers and arguments
with multiple calls to i915_error_printf() worked fine. This patch goes
one step further and introduced i915_error_puts() to pass the strings
simply.
It may not fix the root cause, but it does prevent my box from dying and
I think helps make print_error_buffers() more friendly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66077
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the trend and don't code conditions with platforms but with
features.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By stashing a pointer of who opened the device and keeping a list of
open fd, we can then walk each client and inspect how many objects they
have open. For example,
i915_gem_objects:
1102 objects, 613646336 bytes
663 [662] objects, 468783104 [468750336] bytes in gtt
37 [37] active objects, 46874624 [46874624] bytes
626 [625] inactive objects, 421908480 [421875712] bytes
282 unbound objects, 6512640 bytes
85 purgeable objects, 6787072 bytes
28 pinned mappable objects, 3686400 bytes
40 fault mappable objects, 27783168 bytes
2145386496 [536870912] gtt total
Xorg: 43 objects, 32243712 bytes (10223616 active, 16683008 inactive, 4096 unbound)
gnome-shell: 30 objects, 28381184 bytes (0 active, 28336128 inactive, 0 unbound)
xonotic-linux64: 1032 objects, 569933824 bytes (46874624 active, 383545344 inactive, 6508544 unbound)
v2: Use existing drm->filelist as pointed out by Ben.
v3: Not even stashing the task_struct is required as Ben pointed out
drm_file->pid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it will be used for the global bound/unbound list with full PPGTT,
this helps clarify things for upcoming code rework.
Recommended-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It just prints whether it's supported/enabled/disabled. Feature
requested by the power management team.
v2: Checkpatch started complaining about seq_printf with 1 argument.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Removed rebase relic VECS ring from i915_gem_request_info (Damien)
v3: s/hsw/hws in debugfs which I introduced in v2 (Jon)
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
[Order changed, and modified by]
CC: "Bloomfield, Jon" <jon.bloomfield@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never check the return values, and there's not much we could do on
errors anyway. Just simplify the signatures. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes when user is trying to get error state out from
debugfs after gpu hang, the memory is low and/or fragmented
enough that kmalloc in seq_file will fail.
Prevent big kmalloc by avoiding seq_file and instead convert
error state to string in smaller chunks.
v2: better alloc flags, better truncate, correct
locking, and error handling improvements (Chris Wilson)
v3: printf annotations (Daniel Vetter)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DEV_INFO_FOR_FLAG() now takes 2 parameters:
• A function to apply to the flag
• A separator
This will allow us to use the macro twice in the DRM_DEBUG_DRIVER() call
of i915_dump_device_info().
v2: Fix a typo in the subject (Jani Nikula)
v3: Undef the helper macros (Jani Nikula, Daniel vetter)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to hold the rps lock around punit access.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 647416f9ee
Author: Kees Cook <keescook@chromium.org>
Date: Sun Mar 10 14:10:06 2013 -0700
drm/i915: use simple attribute in debugfs routines
made i915_next_seqno debugfs entry to crop it's output
if returned value was large enough. Using simple_attr
will limit the output to 24 bytes.
Fix is to strip out preamples on all simple attributes
that have one.
v2: Fix all simple attributes (Daniel Vetter)
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most importantly this will allow users to set overclock frequencies in
sysfs. Previously the max was limited by the RP0 max as opposed to the
overclock max. This is useful if one wants to either limit the max
overclock frequency, or set the minimum frequency to be in the overclock
range. It also fixes an issue where if one sets the max frequency to be
below the overclock max, they wouldn't be able to set back the proper
overclock max.
In addition I've added a couple of other bits:
Show the overclock freq. as max in sysfs
Print the overclock max in debugfs.
Print a warning if the user sets the min frequency to be in the
overclock range.
In this patch I've decided to store the hw_max when we read it from the
pcode at init. The reason I do this is the pcode reads can fail, and are
slow.
v2: Report when user requested overclocked max (Daniel)
Remove when user sets min to overclock range (Daniel)
Reported-by: freezer from #intel-gfx on irc
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fixup the s/100MHz/50MHz/ confusion in an unrelated comment
that Mika spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into drm-intel-next-queued
Backmerge Linux 3.9-rc5 since I want to merge a few dp clock cleanups
for -next, but they will conflict all over the place with
commit 9d1a455b0c
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Mar 18 11:25:36 2013 +0100
drm/i915: Use the fixed pixel clock for eDP in intel_dp_set_m_n()
from -fixes.
Conflicts:
drivers/gpu/drm/i915/intel_dp.c: Simply adjacent lines changed.
drivers/gpu/drm/i915/intel_panel.c: A field rename in -next
conflicts with a bugfix in -fixes. Take the version from
-fixes and apply the rename.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Masks kernel address info-leak in object dumps with the %pK suffix,
so they cannot be used to target kernel memory corruption attacks if
the kptr_restrict sysctl is set.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaces the manual read/write routines in debugfs with the common
simple attribute helpers. Doing this gets rid of repeated copy/pasting
of copy_from_user and value formatting code.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Squash in follow-up fix from Kees Cook to fix u64 divides on
32bit platforms.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On error, this represents the state of the currently running context at
the time it was loaded.
Unfortunately, since we're hung and can't switch out the context this
may not tell us too much about the most current state of the context,
but does give clues about what has happened since loading.
Thanks to recent doc updates, we have a little more confidence regarding
what is actually in this memory, and perhaps it will help us gain more
insight into certain bugs. AFAICT, the most interesting info is in the
first page. To save space, we only capture the first page. In the
future, we might want to dump more.
Sample of the relevant part of error state:
render ring --- HW Context = 0x01b20000
[0000] 00000000 1100105f 00002028 ffff0880
[0010] 0000209c feff4040 000020c0 efdf0080
[0020] 00002178 00000001 0000217c 00145855
[0030] 00002310 00000000 00002314 00000000
v2: Move error collection to the ring error code
Change format of dump to not confuse intel_error_decode (Chris)
Put the context error object with the others (Chris)
Don't search bound_list instead of active_list (chris)
v3: extract and flatten context recording (daniel)
checkpatch related fixes for the copypasta in debugfs
v4: bug in v3 (Daniel)
- if ((ring->id == RCS) && error->ccid)
+ if ((ring->id != RCS) || !error->ccid)
References: https://bugs.freedesktop.org/show_bug.cgi?id=55845
Reviewed-by (v2): Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Bikeshed away the redudant parenthese around ring->id != RCS]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Print out the HW context object information per ring. Even though the
existing code only utilizes the render ring, it's simple enough to
support future expansion.
I had this in a patch somewhere in a rev of the original implementation,
but I must have lost it.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: s/context/default context/ bikeshed applied.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Amending
commit 4518f611ba
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 23 16:16:35 2013 +0100
drm/i915: dump UTS_RELEASE into the error_state
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
Daniel writes:
"Probably the last feature pull for 3.9, there's some fixes outstanding
thought that I'd like to sneak in. And maybe 3.8 takes a bit longer ...
Anyway, highlights of this pull:
- Kill the horrible IS_DISPLAYREG hack to handle the mmio offset movements
on vlv, big thanks to Ville.
- Dynamic power well support for Haswell, shaves away a bit when only
using the eDP port on pipe A (Paulo). Plus unclaimed register fixes
uncovered by this.
- Clarifications of the gpu hang/reset state transitions, hopefully fixing
a few spurious -EIO deaths in userspace.
- Haswell ELD fixes.
- Some more (pp)gtt cleanups from Ben.
- A few smaller things all over.
Plus all the stuff from the previous rather small pull request:
- Broadcast RBG improvements and reduced color range fixes from Ville.
- Ben is on a "kill legacy gtt code for good" spree, first pile of patches
included.
- No-relocs and bo lut improvements for faster execbuf from Chris.
- Some refactorings from Imre."
* tag 'drm-intel-next-2013-02-01' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
GPU/i915: Fix acpi_bus_get_device() check in drivers/gpu/drm/i915/intel_opregion.c
drm/i915: Set the SR01 "screen off" bit in i915_redisable_vga() too
drm/i915: Kill IS_DISPLAYREG()
drm/i915: Introduce i915_vgacntrl_reg()
drm/i915: gen6_gmch_remove can be static
drm/i915: dynamic Haswell display power well support
drm/i915: check the power down well on assert_pipe()
drm/i915: don't send DP "idle" pattern before "normal" on HSW PORT_A
drm/i915: don't run hsw power well code on !hsw
drm/i915: kill cargo-culted locking from power well code
drm/i915: Only run idle processing from i915_gem_retire_requests_worker
drm/i915: Fix CAGF for HSW
drm/i915: Reclaim GTT space for failed PPGTT
drm/i915: remove intel_gtt structure
drm/i915: Add probe and remove to the gtt ops
drm/i915: extract hw ppgtt setup/cleanup code
drm/i915: pte_encode is gen6+
drm/i915: vfuncs for ppgtt
drm/i915: vfuncs for gtt_clear_range/insert_entries
drm/i915: Error state should print /sys/kernel/debug
...
The shift changed, hurray.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Useful for statistics or on overflowing bug reports to keep things all
lined up.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The aim of this locking rework is that ioctls which a compositor should be
might call for every frame (set_cursor, page_flip, addfb, rmfb and
getfb/create_handle) should not be able to block on kms background
activities like output detection. And since each EDID read takes about
25ms (in the best case), that always means we'll drop at least one frame.
The solution is to add per-crtc locking for these ioctls, and restrict
background activities to only use the global lock. Change-the-world type
of events (modeset, dpms, ...) need to grab all locks.
Two tricky parts arose in the conversion:
- A lot of current code assumes that a kms fb object can't disappear while
holding the global lock, since the current code serializes fb
destruction with it. Hence proper lifetime management using the already
created refcounting for fbs need to be instantiated for all ioctls and
interfaces/users.
- The rmfb ioctl removes the to-be-deleted fb from all active users. But
unconditionally taking the global kms lock to do so introduces an
unacceptable potential stall point. And obviously changing the userspace
abi isn't on the table, either. Hence this conversion opportunistically
checks whether the rmfb ioctl holds the very last reference, which
guarantees that the fb isn't in active use on any crtc or plane (thanks
to the conversion to the new lifetime rules using proper refcounting).
Only if this is not the case will the code go through the slowpath and
grab all modeset locks. Sane compositors will never hit this path and so
avoid the stall, but userspace relying on these semantics will also not
break.
All these cases are exercised by the newly added subtests for the i-g-t
kms_flip, tested on a machine where a full detect cycle takes around 100
ms. It works, and no frames are dropped any more with these patches
applied. kms_flip also contains a special case to exercise the
above-describe rmfb slowpath.
* 'drm-kms-locking' of git://people.freedesktop.org/~danvet/drm-intel: (335 commits)
drm/fb_helper: check whether fbcon is bound
drm/doc: updates for new framebuffer lifetime rules
drm: don't hold crtc mutexes for connector ->detect callbacks
drm: only grab the crtc lock for pageflips
drm: optimize drm_framebuffer_remove
drm/vmwgfx: add proper framebuffer refcounting
drm/i915: dump refcount into framebuffer debugfs file
drm: refcounting for crtc framebuffers
drm: refcounting for sprite framebuffers
drm: fb refcounting for dirtyfb_ioctl
drm: don't take modeset locks in getfb ioctl
drm: push modeset_lock_all into ->fb_create driver callbacks
drm: nest modeset locks within fpriv->fbs_lock
drm: reference framebuffers which are on the idr
drm: revamp framebuffer cleanup interfaces
drm: create drm_framebuffer_lookup
drm: revamp locking around fb creation/destruction
drm: only take the crtc lock for ->cursor_move
drm: only take the crtc lock for ->cursor_set
drm: add per-crtc locks
...
Well, at least step 1. The goal here is that framebuffer objects can
survive outside of the mode_config lock, with just a reference held
as protection. The first step to get there is to introduce a special
fb_lock which protects fb lookup, creation and destruction, to make
them appear atomic.
This new fb_lock can nest within the mode_config lock. But the idea is
(once the reference counting part is completed) that we only quickly
take that fb_lock to lookup a framebuffer and grab a reference,
without any other locks involved.
vmwgfx is the only driver which does framebuffer lookups itself, also
wrap those calls to drm_mode_object_find with the new lock.
Also protect the fb_list walking in i915 and omapdrm with the new lock.
As a slight complication there's also the list of user-created fbs
attached to the file private. The problem now is that at fclose() time
we need to walk that list, eventually do a modeset call to remove the
fb from active usage (and are required to be able to take the
mode_config lock), but in the end we need to grab the new fb_lock to
remove the fb from the list. The easiest solution is to add another
mutex to protect this per-file list.
Currently that new fbs_lock nests within the modeset locks and so
appears redudant. But later patches will switch around this sequence
so that taking the modeset locks in the fb destruction path is
optional in the fastpath. Ultimately the goal is that addfb and rmfb
do not require the mode_config lock, since otherwise they have the
potential to introduce stalls in the pageflip sequence of a compositor
(if the compositor e.g. switches to a fullscreen client or if it
enables a plane). But that requires a few more steps and hoops to jump
through.
Note that framebuffer creation/destruction is now double-protected -
once by the fb_lock and in parts by the idr_lock. The later would be
unnecessariy if framebuffers would have their own idr allocator. But
that's material for another patch (series).
v2: Properly initialize the fb->filp_head list in _init, otherwise the
newly added WARN to check whether the fb isn't on a fpriv list any
more will fail for driver-private objects.
v3: Fixup two error-case unlock bugs spotted by Richard Wilbur.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two important transitions of the wedged state in the current
code:
- 0 -> 1: This means a hang has been detected, and signals to everyone
that they please get of any locks, so that the reset work item can
do its job.
- 1 -> 0: The reset handler has completed.
Now the last transition mixes up two states: "Reset completed and
successful" and "Reset failed". To distinguish these two we do some
tricks with the reset completion, but I simply could not convince
myself that this doesn't race under odd circumstances.
Hence split this up, and add a new terminal state indicating that the
hw is gone for good.
Also add explicit #defines for both states, update comments.
v2: Split out the reset handling bugfix for the throttle ioctl.
v3: s/tmp/wedged/ sugested by Chris Wilson. Also fixup up a rebase
error which prevented this patch from actually compiling.
v4: To unify the wedged state with the reset counter, keep the
reset-in-progress state just as a flag. The terminally-wedged state is
now denoted with a big number.
v5: Add a comment to the reset_counter special values explaining that
WEDGED & RESET_IN_PROGRESS needs to be true for the code to be
correct.
v6: Fixup logic errors introduced with the wedged+reset_counter
unification. Since WEDGED implies reset-in-progress (in a way we're
terminally stuck in the dead-but-reset-not-completed state), we need
ensure that we check for this everywhere. The specific bug was in
wait_for_error, which would simply have timed out.
v7: Extract an inline i915_reset_in_progress helper to make the code
more readable. Also annote the reset-in-progress case with an
unlikely, to help the compiler optimize the fastpath. Do the same for
the terminally wedged case with i915_terminally_wedged.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And to make Ben Widawsky happier, use the gpu_error instead of
the entire device as the argument in some functions.
Drop the outdated comment on ->wedged for now, a follow-up patch will
change the semantics and add a proper comment again.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been sprinkled all over the place in dev_priv. I think
it'd be good to also move all the code into a separate file like
i915_gem_error.c, but that's for another patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mappable_end, ie. size is almost always what you want as opposed to the
number of entries. Since we already have that information, we can scrap
the number of entries and only calculate it when needed.
If gtt_start is !0, this will have slightly different behavior. This
difference can only occur in DRI1, and exists when we try to kick out
the firmware fb. The new code seems like a bugfix to me.
The other case where we've changed the behavior is during init we check
the mappable region against our current known upper and lower limits
(64MB, and 512MB). This now matches the comment, and makes things more
convenient after removing gtt_mappable_entries.
Also worth noting is the setting of mappable_end is taken out of setup
because we do it earlier now in the DRI2 case and therefore need to add
that tiny hunk to support the DRI1 IOCTL.
v2: Move up mappable end to before legacy AGP init
v3: Add the dev_priv inclusion here from previous rebase error in patch
5
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: squash in fix for a printk format flag mismatch warning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The purpose of the gtt structure is to help isolate our gtt specific
properties from the rest of the code (in doing so it help us finish the
isolation from the AGP connection).
The following members are pulled out (and renamed):
gtt_start
gtt_total
gtt_mappable_end
gtt_mappable
gtt_base_addr
gsm
The gtt structure will serve as a nice place to put gen specific gtt
routines in upcoming patches. As far as what else I feel belongs in this
structure: it is meant to encapsulate the GTT's physical properties.
This is why I've not added fields which track various drm_mm properties,
or things like gtt_mtrr (which is itself a pretty transient field).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[Ben modified commit messages]
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the assertion from the previous patch in place, it should be safe
to get rid gtt_mappable_total. Keeps things saner to not have to track
the same info in two places.
In order to keep the diff as simple as possible and keep with the
existing gtt_setup semantics we opt to keep gtt_mappable_end. It's not
as consistent with the 'total' used in the previous patch, but that can
be fixed later.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[Ben modified commit message]
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a means to investigate some bad system behaviour related to the
purging of the active, inactive and unbound lists, it is useful to be
able to manually control when those lists should be cleared.
v2: use _safe list iterators as we kick objects from the list as we
walk.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add a small comment explaining why we don't need to check and
wait for gpu resets, acked by Chris on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
These are useful for investigating hangs involving WAIT_FOR_EVENT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Apply a droplet of Future-Proof in the if-ladder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This debugs entry can be used to set arbitrary value to next_seqno.
Use i915_gem_set_seqno instead of poking next_seqno.
v2: nasty details of next_seqno and last_seqno handling
moved inside i915_gem_set_seqno as suggested by Chris Wilson.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spinning for up to 200 us with interrupts locked out is not good. So
let's just spin (and even that seems to be excessive).
And we don't call these functions from interrupt context, so this is
not required. Besides that doing anything in interrupt contexts which
might take a few hundred us is a no-go. So just convert the entire
thing to a mutex. Also move the mutex-grabbing out of the read/write
functions (add a WARN_ON(!is_locked)) instead) since all callers are
nicely grouped together.
Finally the real motivation for this change: Dont grab the modeset
mutex in the dpio debugfs file, we don't need that consistency. And
correctness of the dpio interface is ensured with the dpio_lock.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
seqno's are u32 so print accordingly
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed for testing seqno wrapping. Be careful to not bump next_seqno
more than 0x7FFFFFFF at a time (between some handled requests) as
i915_seqno_passed() can't handle bigger difference in between.
v2: Address review comments from Chris Wilson.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Squash in fixup to properly remove the debugfs file on driver
unload again.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- __iomem where there is none (I love how we mix these things up).
- Use gfp_t instead of an other plain type.
- Unconfuse one place about enum pipe vs enum transcoder - for the pch
transcoder we actually use the pipe enum. Fixup the other cases
where we assign the pipe to the cpu transcoder with explicit casts.
- Declare the mch_lock properly in a header.
There is still a decent mess in intel_bios.c about __iomem, but heck,
this is x86 and we're allowed to do that.
Makes-sparse-happy: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use a space after the cast consistently and fix up the
newly-added cast in i915_irq.c to properly use __iomem.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to accommodate objects that are not backed by struct pages, but
instead point into a contiguous region of stolen space, we need to make
various changes to avoid dereferencing obj->pages or obj->base.filp.
First introduce a marker for the stolen object, that specifies its
offset into the stolen region and implies that it has no backing pages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we do not have any domains occupying the high bits, there is no point
in always printing the leading 00.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should be useful to know what the driver thought the other ring's seqno
was when it last used a semaphore.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes a WARN_ON in igt/tests/debugfs_reader
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the power related code to run independently of the rest of
the pipeline, extending the resume and init time improvements into
userspace, which would otherwise have been blocked on the struct mutex
if we were doing PCU communication.
v2: Also convert the locking for the rps sysfs interface.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a special mechanism for communicating with the PCU already
being used for the ring frequency stuff. As we'll be needing this for
other commands, extract it now to make future code less error prone and
the current code more reusable.
I'm not entirely sure if this code matches 1:1 with the previous code
behaviorally. Functionally however, it should be the same.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fixup compile fail reported by Wu Fengguang.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Magic numbers are bad mmmkay. In this case in particular the value is
especially weird because the docs say multiple things. We'll need this
value for sysfs, so extracting it is useful for that as well.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For code consolidation and future maintainability.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-and-Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using the extracted INSTDONE reading, and our new register definitions,
update our hangcheck detection and error collection to use it. This
primarily means changing == to memcmp, and changing = to memcpy.
Hopefully this will give more info on error dump, and provide more
accurate hangcheck detection (both are actually TBD).
Also, remove the reading of instdone1 from the ring error collection
function, and just crap everything in capture_error_state (that could be
split into a separate patch if it wasn't so trivial).
v2: Now assuming i915_get_extra_instdone does the memset we can clean up the
code a bit (Jani)
v3: use ARRAY_SIZE as requested earlier by Jani (didn't change sizeof)
Updated commit msg
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ERR_INT can generate interrupts. However since most of the conditions seem
quite fatal the patch opts to simply report it in error state instead of
adding more complexity to the interrupt handler for little gain (the
bits are sticky anyway).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When dealing with a working set larger than the GATT, or even the
mappable aperture when touching through the GTT, we end up with evicting
objects only to rebind them at a new offset again later. Moving an
object into and out of the GTT requires clflushing the pages, thus
causing a double-clflush penalty for rebinding.
To avoid having to clflush on rebinding, we can track the pages as they
are evicted from the GTT and only relinquish those pages on memory
pressure.
As usual, if it were not for the handling of out-of-memory condition and
having to manually shrink our own bo caches, it would be a net reduction
of code. Alas.
Note: The patch also contains a few changes to the last-hope
evict_everything logic in i916_gem_execbuffer.c - we no longer try to
only evict the purgeable stuff in a first try (since that's superflous
and only helps in OOM corner-cases, not fragmented-gtt trashing
situations).
Also, the extraction of the get_pages retry loop from bind_to_gtt (and
other callsites) to get_pages should imo have been a separate patch.
v2: Ditch the newly added put_pages (for unbound objects only) in
i915_gem_reset. A quick irc discussion hasn't revealed any important
reason for this, so if we need this, I'd like to have a git blame'able
explanation for it.
v3: Undo the s/drm_malloc_ab/kmalloc/ in get_pages that Chris noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Split out code movements and rant a bit in the commit message
with a few Notes. Done v2]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since forcewake is now protected by a spinlock, we don't need to grab
dev->struct_mutex any more. This way we can also get rid of a stale
comment, noticed by Ben Widawsky while reviewing some locking changes.
v2: Kill the unused variable ret, noticed by Fengguang Wu.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid the forcewake overhead when simply retiring requests, as often the
last seen seqno is good enough to satisfy the retirment process and will
be promptly re-run in any case. Only ensure that we force the coherent
seqno read when we are explicitly waiting upon a completion event to be
sure that none go missing, and also for when we are reporting seqno
values in case of error or debugging.
This greatly reduces the load for userspace using the busy-ioctl to
track active buffers, for instance halving the CPU used by X in pushing
the pixels from a software render (flash). The effect will be even more
magnified with userptr and so providing a zero-copy upload path in that
instance, or in similar instances where X is simply compositing DRI
buffers.
v2: Reverse the polarity of the tachyon stream. Daniel suggested that
'force' was too generic for the parameter name and that 'lazy_coherency'
better encapsulated the semantics of it being an optimization and its
purpose. Also notice that gen6_get_seqno() is only used by gen6/7
chipsets and so the test for IS_GEN6 || IS_GEN7 is redundant in that
function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it's easier so see what belongs together, and what is used
by the ilk ips code. Also add some comments that explain the locking.
Note that (cur|min|max)_delay need to be duplicated, because
they're also used by the ips code.
v2: Missed one place that the dev_priv->ips change caught ...
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's no fun if your shell hangs when the driver has gone on vacation
and you want to know why ...
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Take the dev->struct_mutex around access the corresponding state
(and adjusting the rps hw state).
- Add an assert to gen6_set_rps to ensure we don't forget about this
in the future.
- Don't set up the min/max_freq files if it doesn't apply to the hw.
And do the same for the gen6+ cache sharing file while at it.
v2: Move the gen6+ checks into the read/write callbacks. Thanks to the
awesome drm midlayer we can't check that when registering the debugfs
files, because the driver is not yet fully set up, specifically the
->load callback hasn't run yet.
Oh how I despise this disaster ...
v3: Also add a WARN_ON(mutex_is_locked) in set_rps to check the
locking.
v4: Use mutex_lock_interruptible, suggested by Chris Wilson.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (for v2)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handy for lazy people like me, or when people forget to add the output
of lspci -nn.
v2: Chris Wilson noticed that we have this duplicated already in the
i915_capabilites debugfs file. But there \n as separator looks better,
which would be a bit verbose in dmesg. Abuse the preprocessor to
extract this all.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we guarantee to emit a flush before emitting the breadcrumb or
the next batchbuffer, there is no further need for the flushing list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we always flush the GPU cache prior to emitting the breadcrumb, we no
longer have to worry about the deferred flush causing the
pending_gpu_write to be delayed. So we can instead utilize the known
last_write_seqno to hopefully minimise the wait times.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.
And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.
v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes for easier benchmarking and testing. One can set a fixed
frequency by setting min and max to the same value.
v2: fix whitespace & comment (Eugeni)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to remove the debugfs file. Regression introduce in
commit d54423037f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 27 15:17:40 2012 +0200
drm/i915: allow the existing error_state to be destroyed
Reported-and-Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... by writing (anything) to i915_error_state.
This way we can simulate a bunch of gpu hangs and run the error_state
capture code every time (without the need to reload the module).
To make that happen we need to abandon the simple seq_file wrappers
provided by the drm core. While at it put the new error_state
refcounting to some good use and associated the error_state to the
debugfs when opening the file. Otherwise the error_state could change
while someone is reading it. This should help greatly when we finally
get around to split up the giant single seq_file block that the
error_state file currently is into smaller parts.
v2: Actually squash all the fixes into the patch ...
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- reduce the irq disabled section, even for a debugfs file this was
way too long.
- always disable irqs when taking the lock.
v2: Thou shalt not mistake locking for reference counting, so:
- reference count the error_state to protect from concurent freeeing.
This will be only really used in the next patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gpu reset is a very important piece of our infrastructure.
Unfortunately we only really it test by actually hanging the gpu,
which often has bad side-effects for the entire system. And the gpu
hang handling code is one of the rather complicated pieces of code we
have, consisting of
- hang detection
- error capture
- actual gpu reset
- reset of all the gem bookkeeping
- reinitialition of the entire gpu
This patch adds a debugfs to selectively stopping rings by ceasing to
update the hw tail pointer, which will result in the gpu no longer
updating it's head pointer and eventually to the hangcheck firing.
This way we can exercise the gpu hang code under controlled conditions
without a dying gpu taking down the entire systems.
Patch motivated by me forgetting to properly reinitialize ppgtt after
a gpu reset.
Usage:
echo $((1 << $ringnum)) > i915_ring_stop # stops one ring
echo 0xffffffff > i915_ring_stop # stops all, future-proof version
then run whatever testload is desired. i915_ring_stop automatically
resets after a gpu hang is detected to avoid hanging the gpu to fast
and declaring it wedged.
v2: Incorporate feedback from Chris Wilson.
v3: Add the missing cleanup.
v4: Fix up inconsistent size of ring_stop_read vs _write, noticed by
Eugeni Dodonov.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.
Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waiting_seqno is not terribly useful, and as such we can remove it
so that we'll be able to extract lockless code.
v2: Keep the information for error_state (Chris)
Check if ring is initialized in hangcheck (Chris)
Capture the waiting ring (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: add some bikeshed to clarify a comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extra bit of interrupt enabling code doesn't belong in the wait
seqno function. If anything we should pull it out to a helper so the
throttle code can also use it. The history is a bit vague, but I am
going to attempt to just dump it, unless someone can argue otherwise.
Removing this allows for a shared lock free wait seqno function. To keep
tabs on this issue though, the IER value is stored on error capture
(recommended by Chris Wilson)
v2: fixed typo EIR->IER (Ben)
Fix some white space (Ben)
Move IER capture to globally instead of per ring (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: ier is a 16 bit reg on gen2!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The use of the mm_list by deferred-free breaks the following patches to
extend the range of objects tracked. We can simplify things if we just
make the unbind during free uninterrutible.
Note that unbinding should never fail, because we hold an additional
reference on every active object. Only the ilk vt-d workaround breaks
this, but already takes care of not failing by waiting for the gpu to
quiescent non-interruptible. But the existence of the deferred free
list casted some doubts on this theory, hence WARN if the unbind fails
and only then retry non-interruptible.
We can kill this additional code after a release in case the theory is
indeed right and no one has hit that WARN.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify object tracking by removing the inactive but pinned list. The
only place where this was used is for counting the available memory,
which is just as easy performed by checking all objects on the rare
occasions it is required (application startup). For ease of debugging,
we keep the reporting of pinned objects through the error-state and
debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These were mostly straight forward. No forced casting needed.
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
[danvet: fix conflict with ringbuffer_data removal and drop the hunk
about the status page - that needs more care to fix up.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
