commit 85ff3c29d7 ("ASoC: samsung: Rename DMA platform registration
functions") renames the DMA registration functions. Fix the places where
it was left out.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have to disable the ssi irq, as it is not safe for all platforms to
write back into the status register. It also runs into non-linefetch
aborts.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx-pcm-fiq is checking for TE RE bits, so enable them only if
necessary.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip errata for the i.MX35, Rev.2 has the following errata:
ENGcm06222: SSI:Transmission does not take place in bit length early frame sync
configuration
The workaround states, that TX_EN and SSI_EN bits should be set in the same
register write. As the next errata in the document (ENGcm06532) says to always
write RX_EN and TX_EN in the same register write in network mode.
Therefore include the whole write to
CCSR_SSI_SCR_TE and CCSR_SSI_SCR_RE
into the write to
CCSR_SSI_SCR_SSIEN
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds ac97-slave support.
For ac97, the registers have to be setup earlier than for other ssi
modes because there is some communication with the external device
before streaming. So this patch introduces a fsl_ssi_setup function to
setup the registers for different ssi operation modes seperately.
This patch was tested with imx27-pca100.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only CPU DAI driver for Freescale
S/PDIF controller that supports stereo playback and record feature.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
In the case of omap-dmic.c, the error-handling code of
devm_ioremap_resource is also corrected to include releasing the clock.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In fsl_ssi_remove() we need to remove the resources in the opposite order that
they were acquired in probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds generic ac97 reset functions using pincontrol and gpio
parsed from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current naming with a simple asoc_ prefix is too generic for use in
multiplatform kernels.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Provide a common compatible string for device trees to list as a fallback
for simplicity. We don't currently have a binding document but let's not
fix that right now...
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make the device easier to hook up to external components in
system designs and ensure operation when DAPM support becomes mandatory
add DAPM support.
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make the device easier to hook up to external components in
system designs and ensure operation when DAPM support becomes mandatory
add DAPM support.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to ensure that the device continues to work with DAPM support
being mandatory provide stub DAPM widgets and routes.
Note that the public information on the device appears to make no
mention of the FM support the driver appears to have.
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it possible to connect external devices to the CODEC and ensure
continued operation with non-DAPM support removed from the core.
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't set the GPIO values from atomic context so support GPIOs that
can't be controlled from atomic context.
Signed-off-by: Mark Brown <broonie@linaro.org>
Bit 9 of PLL2,3 and 4 is reserved as '0'. The 24bit fractional part
should be split across each register in 8bit chunks.
Signed-off-by: Mike Dyer <mike.dyer@md-soft.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This ensures the driver continues to work with DAPM mandatory and makes
it easier to connect the device up to other components in the subsystem.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Provide external widgets for the CODEC to ensure the device continues to
function with DAPM mandatory and to make it easier to hook the device up
to other components.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the core to do I/O rather than directly calling the driver operations
in order to support further refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Move imx-audmux macro definitions to include/dt-bindings, so they can be
used for devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide DAPM for the device, ensuring operation with DAPM required by the
core and making it easier to hook up external hardware to it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide DAPM for the device, ensuring operation with DAPM required by the
core and making it easier to hook up external hardware to it.
Signed-off-by: Mark Brown <broonie@linaro.org>
The bindings do not carry any resources, as the module only registers
the ASoC platform driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the new dmaengine implementation, the filter_data parameter has
to be set earlier, from pxa_ssp_startup().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_dmaengine_dai_dma_data for passing the dma parameters from
clients to the pxa pcm lib. This does no functional change, it's just an
intermedia step to migrate the pxa bits over to dmaengine.
The calculation of dcmd is a transition hack which will be removed again
in a later patch. It's just there to make the transition more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pxa ssp DAI acts as a user of a pxa ssp port, and needs an
appropriate 'port' phandle in DT to reference the upstream.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the PXA DMA rework, we need the generic dmaengine implementation
that currently lives in sound/soc for standalone (non-ASoC) AC'97
support.
Move it to sound/core, and rename the Kconfig symbol.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a Mic Jack widget to the Tegra+RT5640 machine driver, and document
this in the DT binding. This enables the DT to include the Mic Jack in
the audio routing table, and hence enables capture of audio, in addition
to the previously-working playback.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Tegra30 I2S driver was writing the AHUB interface parameters to the
playback path register rather than the capture path register. This
caused the capture parameters not to be configured at all, so if
capturing using non-HW-default parameters (e.g. 16-bit stereo rather
than 8-bit mono) the audio would be corrupted.
With this fixed, audio capture from an analog microphone works correctly
on the Cardhu board.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Exynos5420 added support for I2S TDM mode. For this, there are some
register changes in the I2S controller. This patch adds the relevant
register changes to support I2S in normal mode. This patch adds a
quirk for TDM mode and if TDM mode is present all the relevent changes
will be applied.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Samsung has different versions of I2S introduced in different
platforms. Each version has some new support added for multichannel,
secondary fifo, s/w reset control and internal mux for rclk src clk.
Each newly added change has a quirk. So this patch adds all the
required quirks as driver data and based on compatible string from
dtsi fetches the quirks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This does not fully map the power control available within the device
but it provides the hooks for routing signals through the device and
allows automatic management of the device low power mode.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure that the recently added path kcontrol list is initialised otherwise
we may crash trying to delete routes that don't have kcontrols.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Attempting to create the route as part of adding a mux control causes us
to attempt to add the same route twice since we loop over all sources
for the mux after creating the control. Instead do the addition in the
callers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The routes linking the widget and the input mux were being added
manually, rather than by the ARIZONA_MUX_ROUTES macro. This patchs adds
the routes to the macro.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Saves some code. We should also be able to manage the power up and reset
registers using DAPM but it's probably more trouble than it's worth in
mains powered systems.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it easer to integrate the device with other on-board components
and ensures correct operation following removal of support for non-DAPM
CODECs.
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO manipulation done by this driver is never in atomic context so
we can use gpio_set_value_cansleep() and support GPIOs that can't be set
from atomic context.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
There is no need for the power down work to be done on a per CPU workqueue
especially considering the fairly long delay before powerdown.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Replace ARRAY_AND_SIZE(e) in function argument position to avoid hiding the
arity of the called function.
The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,f;
@@
f(...,
- ARRAY_AND_SIZE(e)
+ e,ARRAY_SIZE(e)
,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_info_enum_ext() and snd_soc_info_enum_double() are almost identical. The
only difference is that snd_soc_info_enum_double() is also able to handle stereo
controls. Using snd_soc_info_enum double() instead of snd_soc_info_enum_ext()
for the SOC_ENUM_EXT control's info callback allows us to remove
snd_soc_info_enum_ext().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SOC_SINGLE_EXT control has been using snd_soc_info_volsw() for its info
callback since commit 1c433fb ("[ALSA] soc - 0.13 ASoC headers"). The
snd_soc_info_volsw_ext() function has been unused ever since then, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The soc_pm_waitq waitqueue has been around as long as the ASoC framework
existed, but has never been used so far, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook up other devices in boards and is required
by removal of support for non-DAPM CODECs in the core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
This makes it easier to hook into boards and ensures the driver continues
to work with support for non-DAPM CODECs removed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since non-DAPM devices are not going to be supported provide DAPM input
and output widgets and hook them up to the DAIs.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Commit 02502da45 (ASoC: imx-mc13783: Depend on ARCH_ARM) introduced 'ARCH_ARM'
as a dependency for SND_SOC_IMX_MC13783, but this is a non-existent symbol.
This makes the selection of SND_SOC_IMX_MC13783 to be impossible.
Use the correct 'ARM' symbol instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Beep Volume Min/Max was backwards.
Change to SOC_SONGLE_SX_TLV for correct volume representation
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@kernel.org
Description of the Asoc machine driver for an at91sam9x5 based board
with a wm8731 audio DAC. Wm8731 is clocked by a crystal and used as a
master on the SSC/I2S interface. Its connections are a headphone jack
and an Line input jack.
[Richard: this is based on an old patch from Nicolas that I forward
ported and reworked to use only device tree]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There may be some platforms using fsl-ssi that do not have a DMA driver
with generic DMA bindings. So this patch adds support for the generic
DMA bindings, while still accepting the old "fsl,dma-events" property if
"dmas" is not found.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for non-dma pcm for imx platforms with imx-pcm-fiq support.
Instead of imx-pcm-audio, in this case imx-pcm-fiq-audio device is added
and the SIER flags are set differently.
We need imx-pcm-fiq for some boards that use an incompatible codec.
imx-pcm-fiq handles those codecs differently and allows to operate with
them. DMA is not possible because some data sent by the codecs, e.g.
wm9712, is not in the datastream. Also some data is mixed up in the
fifos, so that we need to sort them out manually.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adds a function to parse a default port configuration from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch cleanups empty functions on scu
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds BUSIF support for R-Car sound DMAEngine transfer.
The sound data will be transferred via FIFO which can cover blank time
which will happen when DMA channel is switching.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
