Rather than proceed on and silently return false by default, mention why
we rejected the presence of an EDID as implying the presence of a VGA
monitor. (The question arises whether there is a broken EDID which falsely
reports a digital connection when attached by VGA.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is a moral revert of 6ec3d0c0e9.
Following the fix to reset the GMBUS controller after a NAK, we finally
utilize the 0xa0 probe for a CRT connection. And discover that the code
is broken. Shock.
There are a number of issues, but following a key insight from Dave
Airlie, that 0xA0 is an invalid address on a 7-bit bus (though not if we
were to enable 10-bit addressing), and would look like the EDID port
0x50, it is possible to see where the confusion starts.
In short, a write to 0xA0 is accepted by the GMBUS controller which we
interpreted as meaning the existence of a connection (a slave on the
other end of the wire ACKing the write). That was false.
During testing with a broken GMBUS implementation, which never reset an
earlier NAK, this test always reported a NAK and so we proceeded on to
the next test.
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35904
Reported-and-tested-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Keith Packard <keithp@keithp.com>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon resume, like after a cold boot, we need to forcibly probe the
analog connector and cannot rely on the hotplug status.
Based on a patch by Takashi Iwai.
Reported-by: Stefan Dirsch <sndirsch@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=26952
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After disabling the hotplug interrupts for VGA detection on Ironlake, be
sure to re-enable them again afterwards.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The BIOS writer's guide suggests that a VGA connection will ACK a write
to address 0xA0 and that this should be used before doing legacy
load-detection. Considering the extreme cost of load-detection,
performing an extra DDC seems a risk worth taking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These are not fatal errors, so do not alarm the user by filling the
logs with *** ERROR ***. Especially as we know that g4x CRT detection
is a little sticky.
On the one hand the errors are valid since they are warning us of a
stall -- we poll the register whilst holding the mode lock so not even
the mouse will update. On the other hand, those stalls were already present
yet nobody complained.
Reported-by: Andi Kleen <andi@firstfloor.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18332
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Later initialisation of the encoder often requires that
drm_encoder_init() has already been called, for instance, initialiasing
the DDC buses.
Yet another recent regression, as 819f3fb7 depended upon these fixes
which I missed when cherry-picking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently we have a exact mapping of a connector onto an encoder for its
whole lifetime. Make this an explicit property of the structure and so
simplify the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we don't flush the write then we can not be sure that the border
colour will have taken effect by the time we try to read it back.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Jesse's feedback from using the wait_for() macro was that the msleep
argument was that it was superfluous and made the macro more difficult
to use and to read. As the actually amount of time to sleep is not
critical, the crucial part is to sleep and let the processor schedule
something else whilst we wait for the event, replace the argument with a
hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Like on Sandybridge, disabling the DAC here when doing CRT load detect
avoids forever hangs waiting on the hardware.
test procedure on HP 2740p:
boot with no VGA plugged in, start X,
plug in VGA monitor (1280x1024)
chvt 3
machine hangs waiting forever.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).
This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead. Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a new macro, wait_for, to simplify the act of waiting on a register
to change state. wait_for() takes three arguments, the condition to
inspect on every loop, the maximum amount of time to wait and whether to
yield the cpu for a length of time after each check.
v2: Upgrade failure messages to DRM_ERROR on the suggestion of
Eric Anholt. We do not expect to hit these conditions as they reflect
programming errors, so if we do we want to be notified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Subclass intel_encoder to reduce the pointer dance through
intel_encoder->dev_priv.
10 files changed, 896 insertions(+), 997 deletions(-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable the CRT plug interrupt while doing the force cycle, explicitly
clear any CRT interrupt we may have generated, and restore when done.
Should mitigate interrupt storms from hotplug detection.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This doesn't change the clock limits (minimums), i.e. it won't make it
output 720x576 PAL nor 720x480 NTSC, but it will work with modes like
1080i etc. (including GLX and textured Xvideo, not sure about the
overlay).
Tested on i915 + analog VGA, it would be worth checking if newer chips
(and which ones) still support interlaced mode.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Eric Anholt <eric@anholt.net>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
To make CRT force detect reliable on Cougarpoint, we need to
disable DAC before force detect, and restore back when trigger
is completed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cougarpoint is the new PCH for Sandybridge CPU. This one resolves the
chipset change for display pipeline compared to previous Ibexpeak PCH.
Sandybridge/Cougarpoint has different FDI training parameters, so this also
makes seperate FDI training functions for IBX and CPT. Other change includes
new transcoder DPLL select function to set which DPLL for transcoder to pick
up.
And with another new transcoder C introduced in Cougarpoint, each connector
has new transcoder select bits. This one adds that change to light up VGA.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.
It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The intel_output naming is inherited from the UMS code, which had a
structure of screen -> CRTC -> output. The DRM code has an additional
notion of encoder/connector, so the structure is screen -> CRTC ->
encoder -> connector. This is a useful structure for SDVO encoders
which can support multiple connectors (each of which requires
different programming in the one encoder and could be connected to
different CRTCs), or for DVI-I, where multiple encoders feed into the
connector for whether it's used for digital or analog. Most of our
code is encoder-related, so transition it to talking about encoders
before we start trying to distinguish connectors.
This patch is produced by sed s/intel_output/intel_encoder/ over the
driver.
Signed-off-by: Eric Anholt <eric@anholt.net>
This tries to fix CRT detect loop hang seen on some Ironlake form
factor, to clear up hotplug detect state before taking CRT detect
to make sure next hotplug detect cycle is consistent.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
if no VBT is present, crt_ddc_bus will be left at 0, and cause us
to use that for the GPIO register offset. That's never a valid register
offset, so let the "undefined" value be 0 instead of -1.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: clarified the commit message a bit]
HW guys have an evaluation about the impact about EOS, and say the impact
is quite small, so they have removed EOS detection support. This patch
removes EOS feature.
revert commit 0430296558
directly reverting it gives a hunk error, so please use this one.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: fixed up commit message for update that the feature's really gone]
For CRT hotplug detect status, we have four test results as blue
channel only, green channel only, both blue and green channel, and
no channel attached. Origin code only marks both blue and green channel
case as connected, but ignore other possible connected states. This one
trys to detect CRT by checking no channel attached case instead.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Replace the DRM_DEBUG with DRM_DEBUG_KMS in output device code.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
