Current drm bind/unbind sequence would cause some memory issues.
For example we should not cleanup iommu before cleanup mode config.
Reorder bind/unbind sequence, follow exynos drm.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
[seanpaul fixed spelling typo in commit subject]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-11-git-send-email-jeffy.chen@rock-chips.com
We're trying to access vop registers here, so need to make sure
the pm domain is on.
Normally it should be enabled by the bootloader, but there's no
guarantee of it. And if we wanna do unbind/bind, it would also
cause the device to hang.
And this patch also does these:
1/ move vop_initial to the end of vop_bind for eaiser error handling.
2/ correct the err_put_pm_runtime of vop_enable.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-8-git-send-email-jeffy.chen@rock-chips.com
After snd_soc_unregister_codec, the dai link would remain bound to
the invalid codec. That would cause crashes after unbind dp driver.
Let's unregister audio codec when removing dp driver to prevent that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-7-git-send-email-jeffy.chen@rock-chips.com
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
For the RK3399, the grf_switch_reg name should be RK3399_GRF_SOC_CON20,
not RK3399_GRF_SOC_CON19.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1490147691-4489-5-git-send-email-zyw@rock-chips.com
For RK3399, the phy_cfg_clk is a required clock, if phy_cfg_clk is
disabled, MIPI phy can not work. Let's return a error if there is no
phy_cfg_clk in dts property, when the pdata match RK3399.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1490147691-4489-2-git-send-email-zyw@rock-chips.com
Currently we are adding all components from the dts, if one of their
drivers been disabled, we would not be able to bring up others.
Refactor component match logic, follow exynos drm.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1490152880-21855-1-git-send-email-jeffy.chen@rock-chips.com
-----BEGIN PGP SIGNATURE-----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=BSWh
-----END PGP SIGNATURE-----
Merge tag 'doc-4.11-images' of git://git.lwn.net/linux into drm-misc-next
Pointer for Markus's image conversion work.
We need this so we can merge all the pretty drm graphs for 4.12.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The clk_get_rate return 0 if something goes wrong, so it can never be
less then zero, the ret should be set a error code, otherwise the
cdn_dp_clk_enable will return 0 when it failed at clk_get_rate.
In addition, clk_get_rate() returns an "unsigned long", so use
"unsigned long" instead of "u32" is better.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1488940077-22297-2-git-send-email-zyw@rock-chips.com
The device type isn't used anymore now that workarounds and PHY-specific
operations are performed based on version information read at runtime.
Remove it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-9-laurent.pinchart+renesas@ideasonboard.com
Fixes the following link error when CONFIG_DRM_ANALOGIX_DP is not defined:
ERROR: "analogix_dp_start_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined!
ERROR: "analogix_dp_stop_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined!
Fixes: 3190e58daf ("drm/rockchip: Implement CRC debugfs API")
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Implement the .set_crc_source() callback and call the DP helpers
accordingly to start and stop CRC capture.
This is only done if this CRTC is currently using the eDP connector.
v3: Remove superfluous check on rockchip_crtc_state->output_type
v6: Remove superfluous variable
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-5-tomeu.vizoso@collabora.com
The vopb/vopl switch register of RK3399 mipi is different from RK3288,
the default setting for mipi dsi mode is different too, so add a
of_device_id structure to distinguish them, and make sure set the
correct mode before mipi phy init.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1487577744-2855-3-git-send-email-zyw@rock-chips.com
In order to fully reset the state of the MIPI controller we must assert
this reset.
This is slightly more complicated than it could be in order to maintain
compatibility with device trees that do not specify the reset property.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-24-john@metanate.com
This ensures that the output resolution is known before fbcon loads.
mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to
simplify error cleanup since the order of these operations does not
matter.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-22-john@metanate.com
When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the
internal connection but these flags are meaningless for DSI panels.
Switch the test so that we do not set the P{H,V}SYNC bits unless the
mode requires it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
[seanpaul resolved conflict using macros instead of hardcoded values]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-21-john@metanate.com
As the documentation for readx_poll_timeout says, we want to use the
specialized macro for readl rather than using the generic version
directly.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-19-john@metanate.com
The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler". Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.
For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.
By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier. With the above example we do now
get M = 54, N = 4 as given by the databook.
While doing this, change the loop limits to encode the actual limits on
the divisor, which are:
40MHz >= (pllref / N) >= 5MHz
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-18-john@metanate.com
These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.
Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-17-john@metanate.com
Also don't power up the DSI host at this point since this is not
necessary in order to configure the PHY and we do so later when
selecting video or command mode.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-15-john@metanate.com
This clock rate is derived from the PHY PLL, so it should be calculated
dynamically. This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-14-john@metanate.com
Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends. In order
to send commands we need to write to registers, so pclk must be enabled.
While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-13-john@metanate.com
Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook. Call this after the PHY has
been initialized so that we are able to send commands to the panel.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-12-john@metanate.com
By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case. Copy it into a
stack variable that will be correctly aligned.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-11-john@metanate.com
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-10-john@metanate.com
Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-9-john@metanate.com
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-6-john@metanate.com
In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it. Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-5-john@metanate.com
This is not needed since we can access the mode via the CRTC from the
enable hook. Also remove the "mode" field that is no longer used.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-4-john@metanate.com
This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-3-john@metanate.com
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-2-john@metanate.com
Misc fixes for the 4.11 merge window.
- vmwgfx drm_control node compat patch
- rockchip&zte fix
- compat32 support for dma-buf ioctl (cc: stable ofc, since this is a
massive fumble. oops)
* tag 'drm-misc-next-fixes-2017-02-27' of git://anongit.freedesktop.org/git/drm-misc:
dma-buf: add support for compat ioctl
drm/vmwgfx: Work around drm removal of control nodes
drm/rockchip: cdn-dp: Fix error handling
drm/rockchip: add extcon dependency for DP
drm: zte: fix static checker warning on variable 'fmt'
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It is likely that both 'clk_disable_unprepare()' should be called if
'pm_runtime_get_sync()' fails.
Add a new label for that, because 'err_set_rate' is not meaningful in this
case.
Add a missing call to 'pm_runtime_put()'.
Fixes: 1a0f7ed3ab ("drm/rockchip: cdn-dp: add cdn DP support for rk3399")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220070815.23096-1-christophe.jaillet@wanadoo.fr
