Convert the driver to SPDX license description which allow removing
several lines in the file.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a spelling mistake in several dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix NULL pointer exception on device unbind when device tree does not
contain "has-touchscreen" property. In such case the input device is
not registered so it should not be unregistered.
$ echo "12d10000.adc" > /sys/bus/platform/drivers/exynos-adc/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000474
...
(input_unregister_device) from [<c0772060>] (exynos_adc_remove+0x20/0x80)
(exynos_adc_remove) from [<c0587d5c>] (platform_drv_remove+0x20/0x40)
(platform_drv_remove) from [<c05860f0>] (device_release_driver_internal+0xdc/0x1ac)
(device_release_driver_internal) from [<c0583ecc>] (unbind_store+0x60/0xd4)
(unbind_store) from [<c031b89c>] (kernfs_fop_write+0x100/0x1e0)
(kernfs_fop_write) from [<c029709c>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c0297374>] (vfs_write+0xa4/0x184)
(vfs_write) from [<c0297594>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "while (tries--) {" loop is a postop so it exits with "tries" set
to -1.
Fixes: 232e0f6dde ("iio: chemical: add support for Sensirion SPS30 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align broken line to match upper line parenthesis. Solves the
checkpatch.pl's message:
CHECK: Alignment should match open parenthesis
Signed-off-by: Luciana da Costa Marques <lucianadacostamarques@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is a driver for Texas Instruments Dual, 12-Bit Serial Input
Digital-to-Analog Converter.
Datasheet of this chip:
http://www.ti.com/lit/ds/sbas106/sbas106.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Texas Instruments ADS7866, ADS7867 and ADS7868
8/10/12 bit Single channel ADC.
Datasheet: http://www.ti.com/lit/ds/symlink/ads7868.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7768-1 core ADC receives a master clock signal (MCLK). The MCLK
frequency combined with the MCLK division and the digital filter
decimation rates, determines the sampling frequency. Along with
MCLK_DIV, the power mode is also configured according to datasheet
recommendations.
From user space, available sampling frequencies can be read. However,
it is not required for an exact value to be entered, since the driver
will look for the closest available match.
When the device configuration changes (for example, if the filter
decimation rate changes), a SYNC_IN pulse is required.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Analog Devices drivers are typically GPL v2 only. This patch fixes the
inconsistencies between the module license and SPDX.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add an IIO driver for the ADC hardware present on Ingenic JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We are using "if (ret < 0)" in many places in which the function returns 0
on success. Use "if (ret)" instead for better clarity and correctness.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we snap the timestamp after reading from the buffer and
processing the event. When the IIO poll function is triggered by an
interrupt, we can get a slightly more accurate timestamp by snapping it
prior to reading the data, since the data was already generated prior to
entering the trigger handler. This is not going to make a huge difference,
but we might as well improve slightly.
Do this by using iio_pollfunc_store_time as other drivers do.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add interrupt support for the data ready signal on the BMI160, which fires
an interrupt whenever new accelerometer/gyroscope data is ready to read.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX identifiers (GPL 2) for the BMI160 driver. bmi160.h had an
identifier, but the other files did not.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
-----BEGIN PGP SIGNATURE-----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=M03w
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanup for IIO in the 5.1 cycle
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
* tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (67 commits)
iio: chemical: sps30: remove printk format specifier
staging: iio: frequency: ad9833: Load clock using clock framework
staging: iio: frequency: ad9833: Get frequency value statically
dt-bindings: iio: light: Add max44009
iio: light: add driver for MAX44009
dt-bindings: iio: adc: Add docs for AD7768-1
iio: adc: Add AD7768-1 ADC basic support
staging: iio: cdc: ad7152: remove driver completely
iio: imu: mpu6050: Add support for the ICM 20602 IMU
dt-bindings: iio: imu: add icm20602 bindings to mpu6050
dt-bindings: iio: pressure: add LPS22HH bindings
iio: st_accel: use ACPI orientation data
iio: adc: add NPCM ADC driver
dt-binding: iio: add NPCM ADC documentation
iio: chemical: sps30: allow changing self cleaning period
dt-bindings: iio: chemical: Add bindings for bme680
iio: chemical: bme680: Add device-tree support
iio:st_pressure:initial lps22hh sensor support
iio: accell: mma8452: add vdd/vddio regulator operation support
dt-bindings: iio: accel: mma8452: add power supplies property
...
pr_fmt is used by printk wrappers. There are not any in the driver
code so remove the format specifier.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MAX44009 is a low-power ambient light sensor from Maxim
Integrated. It differs from the MAX44000 in that it doesn't have
proximity sensing and that it requires far less current (1 micro-amp
vs 5 micro-amps). The register mapping and feature set between the
two are different enough to require a new driver for the MAX44009.
Developed and tested with a BeagleBone Black and UDOO Neo (i.MX6SX)
Supported features:
* Reading lux (processed value)
* Rising and falling illuminance threshold
events
* Configuring integration time
https://datasheets.maximintegrated.com/en/ds/MAX44009.pdf
Signed-off-by: Robert Eshleman <bobbyeshleman@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7768-1 is a single channel, precision 24-bit analog to digital
converter (ADC).
This basic patch configures the device in fast mode, with 32 kSPS and
leaves the default sinc5 filter.
Two data conversion modes are made available. When data is retrieved by
using the read_raw attribute, one shot single conversion mode is set.
The continuous conversion mode is enabled when the triggered buffer
mechanism is used. To assure correct data retrieval, the driver waits
for the interrupt triggered by the low to high transition of the DRDY
pin.
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Invensense ICM-20602 is a 6-axis MotionTracking device that
combines a 3-axis gyroscope and an 3-axis accelerometer. It is very
similar to the ICM-20608 imu which is already supported by the mpu6050
driver. The main difference is that the ICM-20602 has the i2c bus
disable bit in a separate register.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Platform-specific ST accelerometer mount matrix information can be
provided by returning a package of 6 integers from the ACPI _ONT
method. This has been seen on Acer products such as Veriton Z4860G,
Z6860G and A890, which include a ST SMO8840 sensor. We have also
confirmed experimentally that the Windows driver uses such information.
The _ONT data format was explained by a ST vendor contact. However,
strangely enough, the _ONT transformations must be applied after first
applying another mount matrix which we determined experimentally. ST
have not commented on why this is the case, but we imagine that perhaps
earlier devices (before _ONT was introduced) required this translation
and hence it became 'standard.'
Interpret the _ONT data and export the equivalent mount matrix to
userspace.
If no _ONT data is present, no mount matrix is exported.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor can periodically trigger self cleaning. Period can be changed by
writing a new value to a dedicated attribute. Upon attribute read
current period gets returned.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit allow the driver to work with device-tree.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@gmail.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initial support for ST LPS22HH pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hh.pdf
Features:
* pressure, temperature data and timestamping channels
* sampling frequency selection [1..200] Hz
* interrupt based trigger
* over I2C or SPI interface
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
- Fix-ups
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
- Bug Fixes
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev
-----BEGIN PGP SIGNATURE-----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=BwG/
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
Bug Fixes:
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev"
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
The accelerometer's power supply could be controllable on some
platforms, such as i.MX6Q-SABRESD board, the mma8451's power supplies
are controlled by a GPIO fixed regulator, need to make sure the
regulators are enabled before any communication with mma8451, this
patch adds vdd/vddio regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The light sensor's power supply could be controllable by regulator
on some platforms, such as i.MX6Q-SABRESD board, the light sensor
isl29023's power supply is controlled by a GPIO fixed regulator,
need to make sure the regulator is enabled before any operation of
sensor, this patch adds vcc regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The magnetometer's power supplies could be controllable on some platforms,
such as i.MX6Q-SABRESD board, the mag3110's power supplies are controlled
by a GPIO fixed regulator, need to make sure the regulators are enabled
before any communication with mag3110, this patch adds vdd/vddio regulator
operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5674R/AD5679R are low power, 16-channel, 12-/16-bit buffered voltage
output digital-to-analog converters (DACs). They include a 2.5 V internal
reference (enabled by default).
These devices are very similar to AD5684R/AD5686R, except that they have 16
channels.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce the TI ADS124S08 and the ADS124S06 ADC
devices from TI. The ADS124S08 is the 12 channel ADC
and the ADS124S06 is the 6 channel ADC device
These devices share a common datasheet:
http://www.ti.com/lit/gpn/ads124s08
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In function xadc_probe, xadc_write_adc_reg can return an error value
when write fails. The fix checks for the return value consistent with
other invocations of the latter function.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8b and Meson8m2 use the same logic to convert the ADC register
value to celsius, which is different from Meson8:
- Meson8 has different multiplier and divider values
- Meson8 uses a 4-bit TSC (temperature sensor coefficient) which fits
into the 4-bit field in the MESON_SAR_ADC_DELTA_10 register:
MESON_SAR_ADC_DELTA_10_TS_C_MASK. Meson8b and Meson8m2 have a 5-bit
TSC which requires writing the upper-most bit into the
MESON_HHI_DPLL_TOP_0[9] register from the HHI register area.
This adds support for the temperature sensor on the Meson8b and Meson8m2
SoCs by implementing the logic to write the upper-most TSC bit into the
HHI register area. The SoC-specific values (temperature_trimming_bits,
temperature_multiplier, temperature_divider) are added - these simply
integrate into the existing infrastructure (which was implemented for
Meson8) and thus require no further changes to the existing temperature
calculation logic.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7606 ADC driver out of staging and into the mainline.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If ad9523_write() fails, indio_dev may get incorrect data. The fix
inserts a check for the return value of ad9523_write(), and it fails,
returns an error.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Self cleaning is especially useful in cases where sensor undergoes
frequent power on/off cycles. In such scenarios it is recommended to
turn self cleaning at least once per week in order to maintain reliable
measurements.
Self cleaning is activated by writing 1 to a dedicated attribute.
Internal fan accelerates to its maximum speed and keeps spinning
for about 10 seconds blowing out accumulated dust.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Tested-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and iio driver pull request for 4.21-rc1.
Lots and lots of tiny patches here, nothing major at all. Which is
good, tiny cleanups is nice to see. No new huge driver removal or
addition, this release cycle, although there are lots of good IIO driver
changes, addtions, and movement from staging into the "real" part of the
kernel, which is always great.
Full details are in the shortlog, and all of these have been in
linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY93w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJRwCfeV0x/+IMS0UGh9ltHnUfCfR9bcgAmgPWMPnY
bauRCLkceTjzODOR4SzH
=o6Fs
-----END PGP SIGNATURE-----
Merge tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and iio driver pull request for 4.21-rc1.
Lots and lots of tiny patches here, nothing major at all. Which is
good, tiny cleanups is nice to see. No new huge driver removal or
addition, this release cycle, although there are lots of good IIO
driver changes, addtions, and movement from staging into the "real"
part of the kernel, which is always great.
Full details are in the shortlog, and all of these have been in
linux-next for a while with no reported issues"
* tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (553 commits)
staging: mt7621-mmc: Correct spelling mistakes in comments
staging: wilc1000: fix missing read_write setting when reading data
mt7621-mmc: char * array declaration might be better as static const
mt7621-mmc: return statement in void function unnecessary
mt7621-mmc: Alignment should match open parenthesis
mt7621-mmc: Removed unnecessary blank lines
mt7621-mmc: Fix some coding style issues
staging: android: ashmem: doc: Fix spelling
staging: rtl8188eu: cleanup brace coding style issues
staging: rtl8188eu: add spaces around '&' in rtw_mlme_ext.c
staging: rtl8188eu: change return type of is_basicrate() to bool
staging: rtl8188eu: simplify null array initializations
staging: rtl8188eu: change order of declarations to improve readability
staging: rtl8188eu: make some arrays static in rtw_mlme_ext.c
staging: rtl8188eu: constify some arrays
staging: rtl8188eu: convert unsigned char arrays to u8
staging: rtl8188eu: remove redundant declaration in rtw_mlme_ext.c
staging: rtl8188eu: remove unused arrays WFD_OUI and WMM_INFO_OUI
staging: rtl8188eu: remove unnecessary parentheses in rtw_mlme_ext.c
staging: rtl8188eu: remove unnecessary comments in rtw_mlme_ext.c
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----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=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c: In function 'st_lsm6dsx_shub_read_reg':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:108:41: warning:
variable 'hub_settings' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit c91c1c844e ("iio: imu: st_lsm6dsx:
add i2c embedded controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support Sensirion SGP30 and SGPC3 multi-pixel I2C gas sensors
Supported Features:
* Indoor Air Quality (IAQ) concentrations for
- tVOC (in_concentration_voc_input)
- CO2eq (in_concentration_co2_input) - SGP30 only
IAQ concentrations are periodically read out by a background thread
to allow the sensor to maintain its internal baseline.
* Gas concentration signals
- Ethanol (in_concentration_ethanol_raw)
- H2 (in_concentration_h2_raw) - SGP30 only
https://www.sensirion.com/file/datasheet_sgp30https://www.sensirion.com/file/datasheet_sgpc3
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Sensirion SPS30 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Measuring particulate matter in ug / m3 (micro-grams per cubic meter)
is de facto standard. Existing air quality sensors usually follow
this convention and are capable of returning measurements using
this unit.
IIO currently does not offer suitable channel type for this
type of measurements hence this patch adds this.
In addition, extra modifiers are introduced used for distinguishing
between fine pm1, pm2p5 and coarse pm4, pm10 particle measurements, i.e
IIO_MOD_PM1, IIO_MOD_PM25 and IIO_MOD_PM4, IIO_MOD_PM10.
pmX consists of particles with aerodynamic diameter less or equal to
X micrometers.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
-----BEGIN PGP SIGNATURE-----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=+vyl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.21 cycle.
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
iio: adc: qcom-spmi-adc5: Initialize prescale properly
dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
iio: adc: Allow selection of Exynos ADC on S5PV210
iio: adc: exynos-adc: Add S5PV210 variant
iio: bmi160: use all devm functions in probe
iio: dac: ad5686: fix bit shift read register
iio:dac:ad5686: Add AD5310R support
Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
dt-bindings: iio: accel: use a generic node name for lis302
iio: core: check 'info' value before registering the device
staging: iio: adc: ad7280a: fix overwrite of the returned value
staging: iio: adc: ad7280a: check for devm_kasprint() failure
iio: humidity: hts221: add entry in MAINTAINERS file
iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
staging:iio:ad2s90: Move out of staging
staging:iio:ad2s90: Add comment to device state mutex
staging:iio:ad2s90: Replace license text w/ SPDX identifier
dt-bindings:iio:resolver: Add docs for ad2s90
staging:iio:ad2s90: Add max frequency check at probe
staging:iio:ad2s90: Remove spi setup that should be done via dt
...
adc5_get_dt_data uses a local, prop, feeds it to adc5_get_dt_channel_data,
and then puts the result into adc->chan_props. The problem is
adc5_get_dt_channel_data may not initialize that structure fully, so a
garbage value is used for prescale if the optional "qcom,pre-scaling" is
not defined in DT. adc5_read_raw then uses this as an array index,
generating a crash that looks like this:
[ 6.683186] Unable to handle kernel paging request at virtual address ffffff90e78c7964
Call trace:
qcom_vadc_scale_code_voltage_factor+0x74/0x104
qcom_vadc_scale_hw_calib_die_temp+0x20/0x60
qcom_adc5_hw_scale+0x78/0xa4
adc5_read_raw+0x3d0/0x65c
iio_channel_read+0x240/0x30c
iio_read_channel_processed+0x10c/0x150
qpnp_tm_get_temp+0xc0/0x40c
of_thermal_get_temp+0x7c/0x98
thermal_zone_get_temp+0xac/0xd8
thermal_zone_device_update+0xc0/0x38c
qpnp_tm_probe+0x624/0x81c
platform_drv_probe+0xe4/0x11c
really_probe+0x188/0x3fc
driver_probe_device+0xb8/0x188
__device_attach_driver+0x114/0x180
bus_for_each_drv+0xd8/0x118
__device_attach+0x180/0x27c
device_initial_probe+0x20/0x2c
bus_probe_device+0x78/0x124
deferred_probe_work_func+0xfc/0x138
process_one_work+0x3d8/0x8b0
process_scheduled_works+0x48/0x6c
worker_thread+0x488/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Unfortunately, when I went to add the initializer for this and tried to
boot it, my machine shut down immediately, complaining that it was
hotter than the sun. It appears that adc5_chans_pmic and adc5_chans_rev2
were initializing prescale_index as if it were directly a divisor,
rather than the index into adc5_prescale_ratios that it is.
Fix the uninitialized value, and change the static initialization to use
indices into adc5_prescale_ratios.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it possible to use Exynos ADC driver on S5PV210 based devices.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we're using the devm version of some but not all functions.
Switch to the devm version of iio_triggered_buffer_setup and
iio_device_register to simplify the code a bit and decrease the chance of
bugs.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch solves the register readback issue with the bit shift. When the
dac resolution was lower than the register size (ex. 12 bits out of 16
bits) the readback value was not shifted with the difference in bits and
the value was higher. Also a mask is applied on the read value in order to
get the value relative to the actual bit size.
Fixes: 0357e488b8 ("iio:dac:ad5686: Refactor the driver")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5310R is a single channel DAC with 10-bit precision, which is
part of the same family as AD5311R, except that it uses the spi interface
instead of i2c. The device has a built-in 2.5V reference which is enabled
by default.
Another important difference is that the SPI write command operation is
16 bits long. The first four bits represent the command, while the
remaining 12 bits are for data. In the control reg, DB9 and DB10 are used
for power-down modes, while DB8 is the REF bit. In order to accommodate
this change, a new regmap type was defined and checked accordingly.
Because AD5310R does not have a readback register, the read_raw operation
will return "Operation is not supported".
Datasheet:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the 'info' structure inside indio_dev is left uninitialized,
a segmentation fault occurs.
Check the 'info' value before using it and if it is equal to
NULL, return with -EINVAL.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI provides a generic helper to get I2C Serial Bus resources.
Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
