For now, allow channel changes immediately and just force the other
virtual wiphys to paused state. This is needed to allow
mac80211-controlled scan to control channel changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify the AP that we may be sleeping longer to allow the AP power
save code to buffer larger number of frames for us when using virtual
wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always going through initialization/deinitialization steps,
do this only for the first/last wiphy to not break the other wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wiphy_select() can be used to select a virtual wiphy to be
activated. Other virtual wiphys will be paused and once that is done,
the operational channel is changed and the wiphys that are on the
selected channel will be unpaused.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).
The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.
Registration of secondary wiphys is added in a separate patch.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.
This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.
Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.
Also be more consistent with using tabs to seperate different
fields.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code easier to understand.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only use case for this right now is ANI calibration,
but more might come up in the future.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).
This also removes some obsolete unused timestamping code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that a new created IBSS network
doesn't break on the first scan.
It seems to Sujith and me that this
stupid code unnecessary, too.
So remove it...
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore network sleep mode in isr if power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used anywhere in ath9k and is just making the code more
confusing.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are number of small details about the keycache operations that
are very easy to miss (and forget), so better include detailed
comments in ath9k_hw_set_keycache_entry() to avoid having to figure
out this every time when having to touch this area.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce stack memory footprint of iwlwifi.
(From >1000 bytes for each *_table_read
on i386 down to 32)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().
rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()
rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.
Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_activate_qos instead of iwl3945_activate_qos.
Patch does two things
1) Patch adds iwl_activate_qos in core library.
2) 3945 makes use of iwl_activate_qos.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following,
1) mac80211's shared data is now initialized in iwl3945_setup_mac.
2) Set the rfkill to right state after initialization
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for iwlagn:
- Have to free eeprom of version check fails - otherwise we end up with
memory leak.
- Include removal of workqueue (created in _setup_deferred_work) in error
handling.
for iwl3945:
- Fix a few places to jump to correct error handling.
- Reorganize error handling to match with code flow.
- Include iwl_free_channel_map as part of error handling.
- Include releasing eeprom as part of error handling.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
unify the set key flow with iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS, TSF maintains local clock counters at each station. Network
Synchronization follows a completely distributed scheme where beacon frames
are generated. Each station maintain its own TSF timestamp, extracted from
beacon timestamps they recieved. Following patch synchronize this beacon timestamp
with uCode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.
Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure we print out a warning when the index is out of bounds,
i.e. even on hw_rix == AR5K_MAX_RATES.
Also change to WARN and print text with the reported hw_rix.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applying kernel janitors todos (reduce stack
footprint where possible) to airo wireless driver.
(Before 1124 bytes on i386, now 876)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin can reach -1 after the loop, so 0 is still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements get_tsf() of ieee80211_ops in the zd1211rw driver.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both the agn and 3945 drivers has some problems with dealing with
errors in their probe functions. Ensure that a goto will undo only
things that was done before the goto was called.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt73usb.c . IDs 'stolen' from the
windows inf file(10/21/2008, 1.03.02.0000) plus some
from the Ralink linux driver(2009_0206_RT73_Linux_STA_Drv1.1.0.2.tar.bz2)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt2500usb.c . IDs 'stolen' from the
windows inf file(02/12/2009, 2.01.01.0015).
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6833c043f9 introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.
In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:
static int el3_rx(struct net_device *dev, int worklimit)
{
while (--worklimit >= 0) { ... }
return worklimit;
}
el3_rx() is only called by function el3_interrupt(): twice:
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
int work_budget = max_interrupt_work;
while(...) {
if (...)
work_budget = el3_rx(dev, work_budget);
if (...)
work_budget = el3_rx(dev, work_budget);
if (--work_budget < 0) {
...
break;
}
}
}
The error path can occur 2 too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: Eric Lauriault <eric@linux.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to only 1500 byte mtu's limits the utility of the veth
device for testing routing. So implement implement a configurable
MTU.
For consistency I drop packets on the receive side when they are
larger than the MTU. I count those drops. And I allow
a little padding for vlan headers.
I also test the mtu when a new device is created with netlink
because that path currently bypasses the current mtu setting
code.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is another user of IXP4xx queue manager, fix it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o set port mode after resetting device.
o prefer cut-through firmware (doesn't require on-card memory).
o load flashed firmware if newer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support larger dma mask if firmware indicates capability
to handle larger addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a
lot of different regions in the chip - to keep the code as clean as possible,
the ranges were put in an H file. Some areas cannot be read if the driver is
running - so by default, the driver will not access those areas - but any
programmer facing a problem will be able to easily manipulate the driver to
extract full dump. The full dump can also be used with kernel dump modules in
case of kernel panic.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the FP index to relevant debug prints and simply beautify some others
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 8726 module detection option is disabled, module should be transmitting
regardless of invalid read from EEPROM
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microcode download requires write of another register and read from
"Limiting/LRM mode" register before setting
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, the FW assumes that no packets will be sent after the driver sends
the FW stop command. To ensure that, the driver must always call
netif_tx_disable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DMA engine (DMAE) to initialize large consecutive memories in the chip
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the napi_poll budget only when updating it. Also add a comment to explain
the rmb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx interrupt is very short and there is no need to limit it to a budget
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rmb to read status block indices on load
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment explains, this smb_mb is needed only if the queue is stopped
(which is unlikely) so the barrier can be moved to that location
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
