'!' has higher precedence than '&' so we need parenthesis here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
drivers/media/video/ov5642.c:985:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:985:1: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/media/video/ov5642.c:985:1: warning: parameter names (without types) in function declaration
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:998:9: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/media/video/ov5642.c:998:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/video/ov5642.c: At top level:
drivers/media/video/ov5642.c:1009:20: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1009:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1009:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/video/ov5642.c:1009:20: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1010:15: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1010:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1010:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/video/ov5642.c:1010:15: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1011:16: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1011:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1011:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/video/ov5642.c:1011:16: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:999:1: warning: control reaches end of non-void function
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
added new bit offset defines,
more supported BE colour formats
and also support BGR565 swapped pixel formats
removed pixfmt helper functions and option flags
setting the configuration register directly in set_pixfmt
added reg_mask function
reg_mask is basically the same as clearing & setting registers,
but it is more convenient and faster (saves one rw cycle).
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Philipp Wiesner <p.wiesner@phytec.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[g.liakhovetski@gmx.de: remove Bayer swap, forward-port, rename macros]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver release for the Omnivision 5642 CMOS sensor.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If vb2_dma_contig_get_userptr() fails on a videobuffer, driver's
.buf_init() method will not be called and the list will not be
initialised. Trying to remove an uninitialised element from a list leads
to a NULL-dereference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that v4l2 subdevices have got their own device objects, having
one more device in soc-camera clients became redundant and confusing.
This patch removes those devices and the soc-camera bus, they used to
reside on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The soc-camera bus is now completely local again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc-camera host drivers shall be implementing their PM, using standard
kernel methods, soc-camera specific hooks can die.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pxa-camera driver doesn't need soc-camera specific PM callbacks,
switch it to using the standard PM hooks instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two fields to the ISP parallel platform data to set the HS and VS
signals polarities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current omap3isp driver is missing regulator handling
for CSIb complex in omap34xx based devices. This patch
adds a mechanism for this to the omap3isp driver.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support to map the buffer using dma_map_single during qbuf which inturn
calls cache flush and unmap the same during dqbuf. This is done to prevent
the artifacts seen because of cache-coherency issues on OMAP4
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce omap_vout_vrfb.c and omap_vout_vrfb.h, for all VRFB related API's,
making OMAP_VOUT driver independent from VRFB. This is required for OMAP4 DSS,
since OMAP4 doesn't have VRFB block.
Added new enum vout_rotation_type and "rotation_type" member to omapvideo_info,
this is initialized based on the arch type in omap_vout_probe. The rotation_type
var is now used to choose between vrfb and non-vrfb calls.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename rotation_enabled() and rotate_90_or_270() to is_rotation_enabled()
and is_rotation_90_or_270() to make them more descriptive.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the inline functions rotate_90_or_270(), rotation_enabled(), and
calc_rotation() from omap_vout.c to omap_voutdef.h.
Move the independent functions omap_vout_alloc_buffer() and
omap_vout_free_buffer() to omap_voutlib.c.
Remove extern identifier from function definitions in omap_voutlib.h
Add static identifier to functions that are used locally in omap_vout.c
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove GFP_DMA from the __get_free_pages() call from omap24xxcam as ZONE_DMA
is not configured on OMAP. Earlier the page allocator used to return a page
from ZONE_NORMAL even when GFP_DMA is passed and CONFIG_ZONE_DMA is disabled.
As a result of commit a197b59ae6, page allocator
returns null in such a scenario with a warning emitted to kernel log.
Signed-off-by: Amber Jain <amber@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove GFP_DMA from the __get_free_pages() call from omap_vout as ZONE_DMA
is not configured on OMAP. Earlier the page allocator used to return a page
from ZONE_NORMAL even when GFP_DMA is passed and CONFIG_ZONE_DMA is disabled.
As a result of commit a197b59ae6, page allocator
returns null in such a scenario with a warning emitted to kernel log.
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the signal state registers to properly populate the signal lock
registers in the cx231xx driver.
This allows applications to know whether there is a signal present even in
devices which lack a tuner (since such apps typically won't call G_TUNER if
no tuner is present).
[mchehab@redhat.com: Fix CodingStyle: don't use {} for one-line if's]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On platforms that have CONFIG_HZ set to 100, the power ramp time effectively
ends up being 10ms. However, on those that have a higher CONFIG_HZ, the time
ends up *actually* being 5ms, which doesn't allow enough time for the hardware
to be fully powered up before attempting to address it via i2c.
Change the constant to 10ms, which is long enough for the hardware to power
up, and won't really be anymore time than it was previously on platforms
with CONFIG_HZ being 100.
Credit goes to Mauro Carvalho Chehab and Gerd Hoffmann who previously
investigated this issue.
Tested with the Hauppauge USBLive 2, with which the problem was readily
reproducible after setting CONFIG_HZ to 1000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch addresses the regression introduced in the cx231xx
driver which stopped the Hauppauge USBLive2 from working.
Confirmed working by both myself and the user who reported the issue
on the KernelLabs blog (Robert DeLuca).
At some point during refactoring of the cx231xx driver, the USBLive 2 device
became broken. This patch results in the device working again.
Thanks to Robert DeLuca for sponsoring this work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Robert DeLuca <robertdeluca@me.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The search for matching extension units fails to take account of the
current chain. In the case where you have two distinct video chains,
both containing an XU with the same GUID but different unit ids, you
will be unable to perform a mapping on the second chain because entity
on the first chain will always be found first
Fix this by only searching the current chain when performing a control
mapping. This is analogous to the search used by uvc_find_control(),
and is the correct behaviour.
Signed-off-by: Stephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.
The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.
While here, document why drxk_t_release should do nothing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds a new control that makes it possible to set the
luma notch filter type to finetune picture quality.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements support for a sharpness control, using the luma
peaking filter feature of cx2388x.
[mchehab@redhat.com: use cx_andor instead of cx_write]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for TV Mixer on Samsung platforms from S5P family.
Mixer is responsible for merging images from three layers and
passing result to the output.
Drivers are using:
- v4l2 framework
- videobuf2
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add drivers for Standard Definition output (SDO) on Samsung platforms
from S5P family. The driver provides control over streaming analog TV
via Composite connector.
Driver is using:
- v4l2 framework
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88 driver would force core->input to always be zero when doing the
the request_acquire(). While it wasn't actually changing the input register
in the hardware, the driver makes decision based on the current input. In
particular, it decides whether to do things like enabling the comb filter
when on a composite input but disabling it on s-video. So for example, on
the HVR-1300, using the s-video input with the MPEG encoder would end up with
the video decoder core configured as though the input type were composite.
In short, the driver state did not match the hardware state.
This patch does two things:
1. It forces the input to zero only if actually switching to DVB mode. This
prevents the input from changing when the blackbird driver opens the device.
2. Keep track of what the input was set to when switching to DVB, and reset
it back when done. This eliminates a condition where for example the user
had the analog side of the board set to capture on the s-video input, then
he used DVB for a bit, then the analog input would unexpectedly be set to
the tuner input.
This work was sponsored by Anevia S.A.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi Format Codec 5.1 is a hardware video coding acceleration
module found in the S5PV210 and Exynos4 Samsung SoCs. It is
capable of handling a range of video codecs and this driver
provides a V4L2 interface for video decoding and encoding.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clear the cx231xx_devused variable and free dev in the error handling code,
as done in the error handling code nearby.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free the recently allocated qcam in each case.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch, based on code by Mirek Slugen, implements support for the
Leadtek WinFast PxDVR3200 H card with XC4000 tuner (107d:6f39).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure that the 'static' keywork is at the beginning of declaration
for drivers/media/video/omap/omap_vout.c
This gets rid of warnings like
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete a couple of leftover fields whose time has passed.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Marvell camera core can support all three videobuf2 buffer modes, which
is slick, but it also requires that all three modes be built and present,
even though only one is likely to be used. This patch allows the supported
modes to be selected at configuration time, reducing the footprint of the
driver. Prior to this patch, the MMP camera driver looked like this:
mmp_camera 19092 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_dma_contig 2188 1 mmp_camera
videobuf2_vmalloc 1718 1 mmp_camera
videobuf2_memops 2100 3 videobuf2_dma_sg,videobuf2_dma_contig,videobuf2_vmalloc
Afterward, instead, with scatter/gather only configured:
mmp_camera 16021 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_memops 2100 1 videobuf2_dma_sg
The total goes from 43,813 bytes to 36,836.
The emphasis has been on simplicity and minimal #ifdef use rather than on
squeezing out every possible byte of code. For configuration, the driver
simply looks at which videobuf2 modes have been configured in and supports
them all; it's simplistic but should be good enough.
The cafe driver is set to support vmalloc and dma-contig; mmp supports only
dma-sg, since that's the only mode that really makes sense to use.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If registration does not work, we don't want to leave the sensor powered on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
