A reference to the rate table is stored inside the
private structure, so there is no need to pass "rate_table"
around.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove various local variables that duplicate information
already stored in mac80211.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're holding the sta_list_spinlock here so we can't sleep.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call cfg80211_michael_mic_failure() handler when there is a MIC error
event from firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The key length can be 32 bytes for TKIP and 16 bytes for AES_CMAC.
'smatch' warns on memcpy using key_len variable to copy data to
a 16 bytes buffer. Use fixed length to avoid the warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume parallel flash is always present, there are boards
with *serial* flash and probably some without flash at all.
Define some bits by the way.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These warnings can be detected by using powerpc64-linux toolchain
(gcc-4.6.3-nolibc).
CC [M] drivers/net/wireless/mwifiex/sta_event.o
drivers/net/wireless/mwifiex/sta_event.c: In function 'mwifiex_process_sta_event':
drivers/net/wireless/mwifiex/sta_event.c:388:4: warning: comparison of distinct pointer types lacks a cast [enabled by default]
CC [M] drivers/net/wireless/mwifiex/uap_event.o
drivers/net/wireless/mwifiex/uap_event.c: In function 'mwifiex_process_uap_event':
drivers/net/wireless/mwifiex/uap_event.c:258:11: warning: comparison of distinct pointer types lacks a cast [enabled by default]
Use min_t() instead of min() to fix the warnings.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to export the il_pci_suspend
and il_pci_resume functions since they're only
referenced from il_pm_ops. The latter can also
be defined using SIMPLE_DEV_PM_OPS instead of
open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put power_level to ah_txpower struct with the rest tx power infos and
also rename it to txp_requested to make more sense.
v2 make sure we don't memset it to zero on reset
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By using cur_pwr on phy_init we re-use the power level previously set by the
driver, not the one we got from above.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rates[i] is unsigned but txp_offset can be negative for newer parts
with PDADC table. We cover the case when rates[i] + txp_offset > 63
but we must also cover the case when its < 0 or else rates[i] will overflow.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure we don't store the table offsets for min and cur power levels,
store the 0.25dB values instead. This way we don't clamp the tx power level
to max (because now cur_pwr holds the 0.25dB value, not the table offset) after
re-using cur_pwr on reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions and structs are not used in an other file and the
prototypes are in no header file, just make them static so the compiler
is able to optimize them better.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the upcoming tpc changes, the driver needs
to provide sensible max output values for each
supported channel.
And while the eeprom always had a output_limit
table, which defines the upper limit for each
frequency and modulation, it was never really
useful for anything... until now.
Note: For anyone wondering about what your card
is calibrated for: check "iw list".
* 2412 MHz [1] (18.0 dBm)
* 2437 MHz [6] (19.0 dBm)
[...]
* 5180 MHz [36] (18.0 dBm)
* 5260 MHz [52] (17.0 dBm) (radar detection)
* 5680 MHz [136] (19.0 dBm) (radar detection)
(for a Dell Wireless 1450 USB Adapter)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out, there are places, that access net->loopback_dev->ifindex
and after ifindex generation is made per-net this value becomes constant
equals 1. So go ahead and introduce the LOOPBACK_IFINDEX constant and use
it where appropriate.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strictly speaking this is only _really_ required for checkpoint-restore to
make loopback device always have the same index.
This change appears to be safe wrt "ifindex should be unique per-system"
concept, as all the ifindex usage is either already made per net namespace
of is explicitly limited with init_net only.
There are two cool side effects of this. The first one -- ifindices of
devices in container are always small, regardless of how many containers
we've started (and re-started) so far. The second one is -- we can speed
up the loopback ifidex access as shown in the next patch.
v2: Place ifindex right after dev_base_seq : avoid two holes and use the
same cache line, dirtied in list_netdevice()/unlist_netdevice()
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifinfomsg is in there (thanks kaber@ for foreseeing this long time ago),
so take the given ifidex and register netdev with it.
Ben noticed, that this code path previously ignored ifmp->ifi_index and
userland could be passing in garbage. Thus it may now fail occasionally
because the value clashes with an existing interface.
To address this it's assumed that if the caller specifies the ifindex for
the veth master device, then it's aware of this possibility and should
explicitly specify (or set to 0 for auto-assignment) the peer's ifindex as
well. With this the compatibility with old tools not setting ifindex is
preserved.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the RTM_NEWLINK results in -EOPNOTSUPP if the ifinfomsg->ifi_index
is not zero. I propose to allow requesting ifindices on link creation. This
is required by the checkpoint-restore to correctly restore a net namespace
(i.e. -- a container).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric noticed, that when there will be devices with equal indices, some
hash functions that use them will become less effective as they could.
Fix this in advance by mixing the net_device address into the hash value
instead of the device index.
This is true for arp and ndisc hash fns. The netlabel, can and llc ones
are also ifindex-based, but that three are init_net-only, thus will not
be affected.
Many thanks to David and Eric for the hash32_ptr implementation!
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various /proc/net files sometimes report crazy timer values, expressed
in clock_t units.
This happens when an expired timer delta (expires - jiffies) is passed
to jiffies_to_clock_t().
This function has an overflow in :
return div_u64((u64)x * TICK_NSEC, NSEC_PER_SEC / USER_HZ);
commit cbbc719fcc (time: Change jiffies_to_clock_t() argument type
to unsigned long) only got around the problem.
As we cant output negative values in /proc/net/tcp without breaking
various tools, I suggest adding a jiffies_delta_to_clock_t() wrapper
that caps the negative delta to a 0 value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: hank <pyu@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__fls(x) is a bit faster than fls(x), granted we know x is non null.
As Ben Hutchings pointed out, fls(x) = __fls(x) + 1
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Avoid dirtying neighbour's confirmed field.
TCP workloads hits this cache line for each incoming ACK.
Lets write n->confirmed only if there is a jiffie change.
2) Optimize neigh_hh_output() for the common Ethernet case, were
hh_len is less than 16 bytes. Replace the memcpy() call
by two inlined 64bit load/stores on x86_64.
Bench results using udpflood test, with -C option (MSG_CONFIRM flag
added to sendto(), to reproduce the n->confirmed dirtying on UDP)
24 threads doing 1.000.000 UDP sendto() on dummy device, 4 runs.
before : 2.247s, 2.235s, 2.247s, 2.318s
after : 1.884s, 1.905s, 1.891s, 1.895s
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing the cpsw device tree example to make it simpler to copy pastable to dts
file and use it directly.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
device tree implementation for davinci mdio driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While playing with CoDel and ECN marking, I discovered a
non optimal behavior of receiver of CE (Congestion Encountered)
segments.
In pathological cases, sender has reduced its cwnd to low values,
and receiver delays its ACK (by 40 ms).
While RFC 3168 6.1.3 (The TCP Receiver) doesn't explicitly recommend
to send immediate ACKS, we believe its better to not delay ACKS, because
a CE segment should give same signal than a dropped segment, and its
quite important to reduce RTT to give ECE/CWR signals as fast as
possible.
Note we already call tcp_enter_quickack_mode() from TCP_ECN_check_ce()
if we receive a retransmit, for the same reason.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing TCP ECN tests, I discovered GRO was reordering packets if it
receives one packet with CE set, while previous packets in same NAPI run
have ECT(0) for the same flow :
09:25:25.857620 IP (tos 0x2,ECT(0), ttl 64, id 27893, offset 0, flags
[DF], proto TCP (6), length 4396)
172.30.42.19.54550 > 172.30.42.13.44139: Flags [.], seq
233801:238145, ack 1, win 115, options [nop,nop,TS val 3397779 ecr
1990627], length 4344
09:25:25.857626 IP (tos 0x3,CE, ttl 64, id 27892, offset 0, flags [DF],
proto TCP (6), length 1500)
172.30.42.19.54550 > 172.30.42.13.44139: Flags [.], seq
232353:233801, ack 1, win 115, options [nop,nop,TS val 3397779 ecr
1990627], length 1448
09:25:25.857638 IP (tos 0x0, ttl 64, id 34581, offset 0, flags [DF],
proto TCP (6), length 64)
172.30.42.13.44139 > 172.30.42.19.54550: Flags [.], cksum 0xac8f
(incorrect -> 0xca69), ack 232353, win 1271, options [nop,nop,TS val
1990627 ecr 3397779,nop,nop,sack 1 {233801:238145}], length 0
We have two problems here :
1) GRO reorders packets
If NIC gave packet1, then packet2, which happen to be from "different
flows" GRO feeds stack with packet2, then packet1. I have yet to
understand how to solve this problem.
2) GRO is not ECN friendly
Delivering packets out of order makes TCP stack not as fast as it could
be.
In this patch I suggest we make the tos test not part of the 'same_flow'
determination, but part of the 'should flush' logic
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce IP latencies by placing hot MIB IP fields in a single cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two instructions to reload dev->nd_net->mib.ip_statistics pointer,
unsing a temp variable, in ip_rcv(), ip_output() paths for example.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence counter will be sent to firmware via key_material
command.
Signed-off-by: Ying Luo <luoy@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cipher' and 'seq' coming from cfg80211 add_key handler will be
parsed in mwifiex_set_encode() to handle AES_CMAC cipher suite.
Signed-off-by: Ying Luo <luoy@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This array was used for wapi_rxpn only. Now it will be used for
AES_CMAC as well. So make a generic name for it.
Signed-off-by: Ying Luo <luoy@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup TX/RX BA tables when AP receives deauthentication from
associated station. During BSS_IDLE event, all wmm queues, BA
streams created for AP interface are deleted.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for handling BA request and BA setup
events for AP interface.
RA list is marked as either 11n enabled or disabled from station's
capabilities in association request. BA setup is initiated only
after some specific number of packets for particular RA list are
transmitted.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for reception and decoding of AMSDU
aggregation frames for AP interface.
Patch also adds support for handling AMSDU aggregation event.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Separate file for uAP RX handling.
2. If received packet is broadcast/multicast, send it to kernel
as well as requeue it back to uAP TX queue.
3. If received packet is for associated STA (intra-BSS), requeue
it back to uAP TX queue.
4. In all other cases (packets for AP or inter-BSS packets),
pass packet to kernel to handle it accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After station is associated an entry would be added to station
list. This entry would have station specific information such as
11n support, AMSDU size. The entry would be deleted after
deauthentication. All station entries would be deleted during
BSS_IDLE event.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Route AP events handling to separate function defined in
uap_event.c.
AP specific event handling is removed from sta_event.c.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If HT IE is present in beacon_data of start_ap cfg80211 handler,
enable 11n flag in AP. Disable 11n flag when stop_ap handler is
called.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier scan command was postponed by 20msec multiple times to give
preference to Tx traffic until we find empty wmm queue.
There is a corner case in which wmm queue becomes empty immediately
after processing the packet(before 20msec) and there may be next
packet coming after some time. In this case we should not resume scan
operation.
We will use new flag to check Tx traffic and resume scan operation
only if there is no traffic for 200msec.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per recent patch "658f37b mwifiex: scan less channels..."
less channels are scanned per scan command in associated state.
Default number of channels per scan command for normal scan are
already 4, but those are 14 for SSID specific scan operation.
This code change in this patch is required for SSID specific scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do similar conversion for Tx packet header but it was missing
for Rx packet header. Without this fix, Rx packet header won't
be correctly parsed on big endian platform.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Padding arithmetic will always work for MSDUs provided first MSDU
ends on 4-byte boundary. Fixing it by making sure that all MSDU ends
on 4-byte boundary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
